Search Documents

By Jerry Tien

Mine regulators are normally used for proper air distribution in underground mines. They are deliberately introduced resistance in the regulated airway, and by altering sizes, they can distribute specific air quantities to regulated splits and free splits (4, 5). The enactment of the Federal Coal Mine Health and Safety Act of 1969, the Federal Mine Safety and Health Amendments Act of 1977, and the regulations adopted by the Mining Enforcement and Safety Administration (now called the Mining Safety and Health ministration) prompted greater discussions of optimal mine regulator locations because of the Act's stringent ventilation requirements (2, 3). For example, by requiring the separation of the air used in the belt haulage entries from the intake and return airways, the regulations required the creation of a third type of airway---the neutral airway, as opposed to the intake and return airways, adding to the complexity of a mine's ventilation network. It is the intent of this report to show that panel regulators should be located in intake airways at the neck of a panel for a blowing fan system and in return airways at the neck of a panel for an exhausting fan system in order to achieve optimal air control. A computer simulation model is used to determine optimal mine regulator location.

Jan 1, 1983

By Tapiwa Chenje, Victor Olivas, Peter Radziszewski

"Ore breakage and grinding media wear have always been considered and determined separately in laboratory tests. However the two processes are linked with the ore broken down in any comminution device being responsible for the majority of the steel wear experienced. The Comminution Dynamics Laboratory (CDLab) successfully developed a test methodology that can more accurately predict grinding media wear in tumbling mills than the Bond Abrasion test. This paper looks at the possible application of the abrasive wear methodology to determine breakage parameters of the same ore used in the abrasion test. Results indicate that breakage parameters comparable to t10 can be determined using the Steel Wheel Abrasion Test (SWAT), while using significantly less ore than standard breakage tests.BACKGROUNDThe Rubber Wheel Abrasion Test (RWAT) is an internationally accepted and widely used method for determining the abrasion wear behavior of materials. The abrasion wheel test was developed to primarily utilize a steel wheel (Brinell, 1921). Haworth (1949) criticized using of the steel wheel by arguing that increasing the contact area size in the steel wheel test causes a change in the wear rate with time. He suggested that the use of a rubber wheel instead eliminates this problem, leading to the adoption of the RWAT which was standardized in ASTM G65 (2004).Radziszewski (2002), however, found that the use of the Steel Wheel Abrasion Test (SWAT) was more applicable for wear testing in the mining industry for two critical reasons. Firstly, the major cause of wear in a ball mill, the most frequently used comminution device, is ball-ore-ball contact and also ball-ore-liner which both are metal-ore-metal contact. Therefore, using the steel wheel has the advantage of providing a similar abrasive environment to the one that takes place in a real ball mill. Secondly, the SWAT creates the potential of running experiments at much higher force regimes that are closer to what happens in actual mills, unlike the RWAT which is a low stress test."

Jan 1, 2011

By Wheeler Davey

WHEN metals are subjected to mechanical working, such as rolling, one of the phenomena that take place is a movement of the crystals of the metal into a system or systems of orientation which bear an angular relation to the direction of working. In rolled metal the crystals may orient themselves with respect to the rolling plane or the rolling direction, or both. Direct evidence of the existence of preferred orientations in rolled metal has been obtained by numerous investigators from X-ray patterns of the rolled metal. Most of these workers used a monochromatic pinhole method. Where the degree of preference for a single orientation is high the monochromatic pinhole pattern may be interpreted by a geometrical calculation based on the angular relationships of the planes in the crystal and the diffraction arcs on the X-ray pattern. This process may be aided by the geometrical construction of the locus sphere (Langenkugel), and reflection circles of Polanyi,1 Polanyi and Weissenberg,2 and Mark and Weissenberg,3 and of the plane polar figures (flachenpolfigur) of Franz Wever.4 R. M. Bozorth5 solves X-ray patterns from metals having a single preferred orientation by means of a series of charts which when placed over the X-ray pattern give directly certain angular relationships, between the crystal planes and the surface of the specimen.

Jan 1, 1929

By V. T. McLemore

Petrographic analysis of rocks is traditionally performed with optical microscopy using thin sections and point counting. However, this does not provide accurate mineral proportions for sedimentary, volcanic, and soil-like material, because rock fragments, groundmass, and matrix are not identified as specific minerals. In addition, groundmass phases in volcanic rocks can be too fine to identify individually, and making thin sections of intact soil-like material is difficult because much of the material is not well cemented. ModAn is a normative calculation that estimates modes ??by applying Gaussian elimination and multiple linear regression techniques to simultaneous mass balance equations? (Paktunc, 2001) and allows location-specific mineral compositions to be used. One of the features of ModAn that makes it appropriate for this study is that it can model one of several sulfide minerals. Mineral compositions for Questa minerals were determined from electron microprobe analysis and entered into ModAn. Then by combining and normalizing results, bulk quantitative mineralogy can be determined using ModAn, petrographic observations, electron microprobe analysis, clay mineral analysis, and the whole-rock chemistry of the sample.

Jan 1, 2009

By K. E. Robinson, G. Re, L. Skoski

Introduction A new technology is evolving as a result of growing industry and government concerns over the potential impacts of possible airborne emissions from uranium tailings piles. A major component of the technology is the use of earth covers to stabilize the tailings after mill operations have ceased. While various analytical models have been used to predict the thickness of required covers, experimental validation of the models has been necessary. This paper presents the results of a field program to select and test cover material to determine its suitability for eventual reclamation of a currently active tailings pile. The two main criteria guiding the study were the U.S. Nuclear Regulatory Commission radon flux requirements (reduction to less than twice background pre-1979, and to 2 pCi/m2 -sec above background post-1979) and the desire to employ locally available material. The methodology chosen for this study consisted of three main elements: o Determination of the background radon flux. o Determination of the radon flux from the tailings pile. o Experimental determination of the cover material diffusion coefficient and and calculation of cover thickness. The first two elements of the study are relatively straightforward, the last phase is discussed in detail. Background Radon Flux Measurements of radon-222 emanation rates from the surface of the ground were taken at three sampling locations. Samples were collected by means of the accumulator can method described by Wilkening, 1977. Both morning and afternoon samples were collected at each site to obtain an average. The measured fluxes were fairly uniform and did not differ greatly among sites. The overall average flux for all sites was 0.63[+]0.28(o) pCi/m2 -sec. This value is equal to the average radium-226 concentration determined in the soil, thus yielding a one to one ratio of radon-222 emitted (in pCi/m2 -sec) to soil radium content (in pCi/g). Tailings Pile Radon Flux Two sites on the tailing pile

Jan 1, 1980

By D. Fenn, A. du Kanda, D. Dukhan

"SynopsisGibb Consulting Services was contracted by Eskom Line Engineering Services to conduct an investigation to determine the absolute displacement to date and infer the current rate of displacement of unsurveyed colliery backfill.At the test site, where a 400 kV power line is to be constructed, neither the surface nor the backfill material had been monitored and it was not possible to state whether the surface will be subject to future settlement that may compromise surface infrastructure. Therefore indirect methods of estimating current and future displacements needed to be found to act as a proxy for a comprehensive long-term settlement monitoring exercise and provide a reasonable estimate for the settlement that has occurred in the decades of mining.The innovative solution was to recover essentially undisturbed core from backfill using a sonic drill rig and use the measured dry density values from the samples as a proxy for the rate and absolute displacement in the backfill.The success in obtaining an essentially undisturbed backfill core and the clear relationship of the backfill density with age and depth allowed the conclusion to be issued that the power line infrastructure can be constructed over the backfill; with a warning that once the water table recovers after mining ceases some collapse settlement may occur.With this method, the amount of settlement can be predicted and, if proven conclusively, provides a way to confidently release huge areas of currently waste ground for future surface infrastructural development.IntroductionIn coal mining, it is normal mining practice to backfill the newly mined-out voids with the excavated waste rock and soils. As there is no requirement for the mining companies to uniformly compact the spoil or accurately monitor surface or inter-backfill displacement, these backfilled voids are prone to differential compaction and consolidation settlement. They are therefore avoided as sites for future surface infrastructure work, especially for linear structures such as roads, railways, and power lines."

Jan 1, 2015

By L. L. Peterson, W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and truck at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. Haulage Cycle Established from Existing Operations For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between and the shovel and trucks with the new truck cycle times.

Jan 12, 1968

By Steven G. Grannes

The Bureau of Mines, U.S. Department of the Interior, has developed a computer image processing algorithm to determine the size distribution of moving taconite (iron ore) pellets. This algorithm interprets line-scan images to measure pellet diameters. Pellet edge detection with a peak light intensity constraint is the basis of this technique. Preliminary error analysis indicates a normally distributed experimental error with a standard deviation of 0.09 and 0.15 for pellet diameters of 0.4 and 0.9 cm, respectively. System accuracy was independent of moving pellet speed below 50 cm/sec. Computer image-based size distributions were found to be in close agreement with standard sieve analysis.

Jan 1, 1986

By K. Oraee

The empirical rock failure criteria play an important role in predicting the mechanical behavior of rocks, since affecting parameters on the behavioral properties of rocks are complex and numerous. Usually the empirical failure criteria are obtained by statistical methods, namely by means of fitting the mathematical function onto the experimental data. For evaluation and verification of the results, however, the quality and accuracy of the fit must be considered. This paper studies the efficiency and accuracy of conventional empirical rock failure criteria using a new approach, which is based on the analysis of uncertainty amplitude on the constant parameters of each criterion. The approach adopted here, is based on the combination of some parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), type of function, degree of freedom and the confidence level of constants. Correlation coefficient (R2) is then a comprehensive test and can be used effectively for comparison and accuracy of empirical rock failure criteria.

Jan 1, 2012

By CORNELIUS STEPHANUS LODEWYK SCHUTTE, WIEHAN ADRIAAN PELSER, JEAN HERMAN VAN LAAR, MICHAEL DAVID HARMSE

Rising electricity costs in South Africa have resulted in a need for optimized compressed-air networks in the mining environment. As a result, the financial benefit of air receivers needs to be reconsidered along with the economic dispatch strategy. This study investigates the use of an evolutionary algorithm in the mining industry to determine the potential financial benefit for various-sized air receivers, as well as their dispatch strategy. A genetic algorithm was selected due to the improved solution reliability and accuracy compared to other optimization techniques. This study indicates that a genetic algorithm can be used to determine the optimal dispatch of compressed air in the deep-level mining industry. Further, this study indicates that air receivers are financially viable in the mining industry and can be used to reduce operating costs, improving profitability.

Dec 1, 2022

By Michael David Harmse, Wiehan Adriaan Pelser, Jean Herman van Laar, Cornelius Stephanus Lodewyk Schutte

The South African deep-level mining industry is characterised by high operating costs and narrowing profit margins. Compressed air is commonly the largest consumer of energy in these mines, and any inefficiencies reduce profitability. Various methods aiming to optimise the compressed air networks have been implemented without an ideal economic dispatch strategy due to the lack of compressed air storage. In this study, a genetic algorithm was developed to evaluate the financial benefit of converting underground haulage to act as an air receiver (compressed air storage). By converting inactive haulage of 1.17 km in length into a volumetric air receiver, an annual monetary benefit of R2.5 million ($163 200) can be achieved, with a payback period of fewer than eight months. However, implementing the ideal size air receiver would result in an annual monetary benefit of R7.67 million ($500 700).

Jul 11, 2022

By Harry Roeser

Short cuts for determining the constants of oil decline curves, with the method of least squares as a starting point, are presented and applications made to practical examples. The nature of the raw data does not justify rigid adherence to the orthodox theory but does lend justification to convenient methods of approximation within reasonable limits. If the conventional form y = kxn were changed to y = k(x + c)', methods of determining the curves would be simplified and greater uniformity in calculated results would probably follow. As A result of the publication, several years ago, of some articles on determining the constants of empirical formulas, the determining the constant's of types of curves used for estimating the production decline of oil wells was brought to the writer for study. Methods requiring a minimum of time and labor and a maximum of rigor were sought, as it appeared that the nature of the data from which such curves are computed and the relative uncertainty of occurrence of the events predicted from them did not justify close adherence to the theory on which the solution of such problems is ordinarily based. The technical deficiencies of the solutions presented in this paper, from the standpoint of the method of least squares, are readily apparent to those familiar with that method, but their presentation in detail here is irrelevant to the subject matter. However, it is the author's conviction, after a rather exhaustive study of the problem, that the value of the solutions lose little by the approximate application of the conventional theory. It must be understood by those who use these formulas that the solutions herein given, and the formulas based on them, are merely facilities to aid the valuation engineer in forecasting future events. It is assumed, also, that before application is made of them, prescient judgment based on the circumstances in each case, shows that the forecast has some probability of realization. On this basis only will these formulas be found useful.

Jan 6, 1924

By F Radke, P A. Tilyard

Determination of the mineralogical location (deportment) of minor and trace elements (including credit and penalty elements) in base metal concentrates can indicate whether further processing is likely to (a) reduce the levels of the penalty elements, and/or (b) direct selected elements into other plant products, thereby increasing current concentrate grade or increasing payment for credit elements. To determine the deportment of elements requires knowledge of the proportions of the minerals present and their individual element contents. In addition, knowledge of the liberation and locking is important, as this can affect any possible further processing. Mineral proportions can be determined by a variety of methods including chemical analysis, point-counting, area-counting, QEM*SEM, image analysis and mineral separation. In the case of a Broken Hill zinc concentrate, several of these methods were used and gave consistent results.

Jan 1, 1998

By Smith T

Bacterial oxidation is often attributed with the advantage that a high level of gold recovery can be obtained at a relatively low level of sulphur oxidation. This is sometimes attributed to the bacteria "tunneling" towards gold inclusions, however it is often due to the presence of two or more sulphides of differing gold content which leach at different rates. Gold is liberated from the individual sul- phides linearly with oxidation. The distribution of gold between pyrite and arsenopyrite in two samples taken from a prospective gold resource was examined. The two samples showed differing responses to bacterial oxida tion and it was shown that this was due to differing intrinsic gold grades in the mineral phases and differing proportions of the minerals in the two samples.

Jan 1, 1991

Traditionally, production volume has been considered the major determinant of cost. As volume increases, total cost increases but unit cost decreases. This concept has been so widespread in industry that many of the tools used to analyze costs are based on production volume as the sole measure of activity and driver of unit cost-fixed and variable costs, cost-volume-price and breakeven analysis, contribution margin, flexible budgets, and others. Clearly, volume is a driver of cost. It is important in both a tactical sense (to the manager at an operating mine) and a strategic sense (as one determinant to the firm's overall cost position). However, many other factors influence costs as well, even though they have not been studied to the same extent. For example, production managers know that their costs will be reduced if the workforce does not have accidents. Safety costs are to a large extent independent of volume. Other cost components increase as volume increases, such as some environmental charges. Some costs may or may not reflect volume changes. Maintenance, for example, may appear as either a fixed or variable cost, as can operating labor in facilities that are highly automated. In the strategic sense, where the firm is selecting a strategy to pursue competitive advantage and increased profitability, all costs are variable. This reflects both the strategic intent and the long-term time frame associated with strategic positioning. Tactically, on a month-by-month basis, some costs are essentially fixed. Cost driver analysis must therefore consider the relevant time frame.

Jan 1, 1999

By Dr. Zach Agioutantis, Elliott Morgan

The explosives, mining, and heavy civil industries consistently battle the uncertainty that is associated with working with a heterogenous medium like rock in blasting. This has led to studies to increase fundamental understanding of material response under dynamic loading that is associated with blasting. This study looks at the dynamic strain associated with blasting the lab Split-Hopkinson Pressure Bar (SHPB) testing while also building off of previous studies with the goal of better understanding the dynamic forces that are enacted on a geologic body during a blast loading event. This is required in order to advance geologic blast response modeling. This is achieved through analyzing the stress and strain values for each specimen that are calculated from strain data collected with a SHPB. Based on this data, the dynamic material response characteristics are able to be determined. Tests were conducted on five Berea Sandstone specimens with a rough length to diameter ratio (L/D) of 1.0. The strain data from these tests were then used to create stress strain curves as well as charts depicting failure stress to both strain rate and failure particle velocities. The tests conducted returned similar results to previous tests results on Berea Sandstone while also showing a correlation between strain rate at failure and failure particle velocities. While further research is needed, there is evidence that SHPB test data could be used in conjunction with the MBF model. The MBF model states that the peak particle velocity (PPV) of blast vibrations can be correlated with deformation (strain) at a given point. With a further understanding of dynamic material response correlated to PPV measurements, further refinement could allow for better prediction of blast performance.

Jan 21, 2025

By Y Peng, D Liu, S Vink, B Wang

There have been strong industrial observations that clay minerals have a deleterious effect on mineral flotation grade and recovery. However, rigorous explanation on the role of clay minerals in flotation and effective ways to reduce their negative effects are not available. In this study, the flotation behaviour of low quality and high quality coal samples were examined at the Xstrata Oaky Creek Coal plant, and laboratory in fresh and recycled water with high ionic strength. Anionic and non-ionic dispersants including lignosulfonates and triblock copolymers were also tested with an objective of improving coal flotation in recycled water. It was found that overly stable froth was produced in the flotation of both low quality and high quality coal samples in saline water. Speciation modelling indicated precipitation of hydrophilic components which may adversely affect the flotation. Despite the overly stable froth, saline water produced much higher combustible recovery than fresh water without significantly losing the product quality. Lignosulfonate dispersants displayed a potential to improve the flotation in fresh water, but not in saline water. Significant flotation improvement was achieved with the triblock copolymer examined in both fresh and saline water.CITATION:Liu, D, Wang, B, Peng, Y and Vink, S, 2012. Determining the effect of clay minerals on coal flotation using saline water, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 151-158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S. K. Sharma, D. A. Stanley

The US Bureau of Mines is investigating the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters, namely, shear rate, polymer dosage, and polymer concentration, on floc growth and to determine the applicability of a model for predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. The results showed that the model reproduces the experimental data with only reasonable accuracy and that it was relatively insensitive to the parameters. Results of the flocculation study showed that increases in the polymer dosage had a greater effect on the time required to reach the maximum floc size than on the floc size itself: It was also determined that, given all the above parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on floc growth.

Jan 1, 1995

By S. K. Sharma

The Bureau of Mines has investigated the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters such as shear rate, polymer dosage, and polymer concentration on floc growth and to determine the applicability of a model in predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. Results show that the model, using GA as a tool to determine the unknown parameters, reproduces the experimental data with only reasonable accuracy and was relatively insensitive to the parameters. Results of the flocculation study showed that increases in polymer dosage had greater effect on the time required to reach the maximum floc size than on the floc size itself. It was also determined that, given all the aforementioned parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on the floc growth.

Jan 1, 1993

By C. J. Johnson, C. J. Bise

"As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity.Room-and-pillar mining accounts for approximately 68% of the nations underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-mid-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.IntroductionThe ultimate goal for any coal mining company is to effectively use its human and financial resources to maximize its profits through the extraction of its reserves. Although recent workforce reductions in the industry have resulted in a more efficient use of labor and increased productivity, there comes a point in time when further reductions in the numbers of workers in each operating section are impossible with existing equipment. For example, Farinelli and Bise (1987) found that labor cost constituted 62% - 73% of the cost per ton of coal at the mining section, with a minimum crew size. Thereafter, efforts to increase productivity must focus on more efficient mine plans and technology.The fact that an increase in productivity can be realized by reducing non-productive time (change-out and tram time) and converting it to productive time has been known and demonstrated for quite some time. What has not been demonstrated frequently is the quantification of the potential productivity increase of currently emerging technology or ""add-on"" equipment. It is one thing to be able to say that a piece of equipment will make an operation more productive, but it is another thing to be able to quantify the productivity increase that will justify the purchase of the new equipment. Not only is a financial benefit possible in room-and-pillar mining with an increase in productivity, but a decrease in the time necessary to develop a longwall panel can also occur.The purpose of this paper is an analyze the impacts of a changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to several scenarios incorporating emerging technology. To do this, four cases will be developed. A base case, consisting of the typical manner in which continuous-miner sections are currently operating, is compared to three layouts incorporating: (1) flooded-bed scrubbers on radio remote-controlled continuous miners, (2)a continuous miner with side-mounted roofbolters, and (3) a continuous miner with side-mounted roofbolters used in conjunction with a continuous-haulage system."

Jan 1, 1989