Search Documents

By Kot F. v. Unrug

In spite of extensive research and accumulated experience from mining operations, appropriate coal strength values for pillar design remain debatable. Coal strengths determined in the laboratory on standardized samples vary widely among various coal seams with poor repeatability. Penetrometric in situ strength testing obtains multiple measurements at multiple horizons within the coal seam to provide a strength profile. Alliance Coal has used that method in many of its mines for pillar design. Pillars in these mines perform well. This paper presents a series of case studies and discussion of issues related to coal pillar design. The analysis demonstrates that the proposed default in situ strength of 900 psi is appropriate when no other data exist. However, in the case of appropriate strength measurements combined with analysis of pillar structural composition, differing values can be used successfully. In areas where the penetrometric derived in situ strength is greater than the standard 900 psi in situ strength, reserve recovery has been optimized as required by law without compromising safety.

Jan 1, 2009

By Sumit Kumar Biswas, Moyukh De, Sibapriya Mukherjee

"The piles often are also subjected to lateral (horizontal) forces and moments. In fact, there are some structures where the primary function of piles is to transfer lateral loads to the ground. Proper analysis of laterally loaded piles is very important to the geotechnical and civil engineering profession.In the present investigation an experimental study has been carried out with free head short model cast iron hollow piles of outer diameter of 24 mm and L/d ratios of 8, 10, and 15. The experimental results have been supplemented by numerical techniques using PLAXIS-3D Foundation version 2.1 software. The results have been found to agree reasonably well with the experimental results. Further finite difference approach has been adoptedto reduce the computational time and to calculate the coefficient of modulus of subgrade reaction (?h) from the load- deflection data obtained from PLAXIS output at different pile depths. The parametric study has been extended for the non-dimensional form defined as flexibility ratio (F.R.),where ?h, L, Ep and Ip are the coefficient of modulus of sub-grade reaction, the embeddedlength of model pile, elastic modulus of pile material and the moment of inertia of model pile about the central axis respectively).The variation of coefficient of horizontal modulus of sub-grade reaction (?h) has been studied with respect to the following parameters for homogeneous soil system: relative density andL/d ratio. It has been found that the logarithm of flexibility ratio increases with increase inrelative density and increase inL/d Ratio. The values of ?h obtained by the proposed method have been, found to be close to the numerical results.As output of this research, graphs have been generated in respect of different parametric variations to gain an insight into behavior of piles under lateral load for short piles."

Jan 1, 2015

By A. H. Brisse

In considering the use of a coal or a coal blend for the production of metallurgical coke, the fact is often overlooked that laboratory data can be most effectively used to determine coke plant operating conditions conducive to maximum output as well as to predict the quality of coke produced. The discussion here presented attempts to point out the manner in which carbonization data can be interpreted for industrial use and the significance of specific laboratory test results in this interpretation. The major considerable must, of course, be the safeguarded of coke oven batteries, against wall damage arising either from excessive carbonization pressures or from the wedging of the pushing ram into non-contracting coke charges. In order to be specific in the matter of handling the laboratory data involved, two series of blends are analyzed. The first of these, referred to as the "AB" series, is typical of some d' the more highly expanding Eastern- coal blends whereas the second series, here referred to as the "CD" series, is probably more typical of the Western coal blonds. Reference to Table II should be made for rank of coals considered in these blends.

Jan 1, 1959

By Fookes R. A, Bunch K, Gravitis V. L, Watt J. S

The combustible volatile matter in coal mine roadway dusts (CVM) has been determined using x-ray backscatter techniques. The correlation between x-ray and chemical techniques is reasonably good for the 92 samples from collieries on the Bulli seam, and the maximum error expected at the maximum level of 11· 5 weight per cent CVM permitted in the N.S.W. Coal Mines Regulation Act, 1912, as amended, is about ± 2·5 weight per cent. This x-ray technique can be used only when the combustible volatile content of the coal matter (cvm) varies within a limited range, and a separate calibration is required for each coal seam.Portable equipment based on a radioisotope x-ray source ahd digital ratemeter makes possible simple and rapid analysis, and with adaptation to use in coal mines should lead to much more comprehensive testing- ofroadways and hence improved overall prevention of coal dust explosions.

Jan 1, 1977

By G. Brackebusch, S. J. Jung

Backfilling techniques are widely used in large-scale underground mines. Massive pillars, which have been left in place for stability, limit mining activity. Backfilling allows safe recovery of the ore remaining in pillars and assures long term stability. In deep mines expected high stress can be relieved with the backfill. Initially, waste rock was used to fill the openings with mixed results. The need to improve safety and reduce costs has prompted the industry to investigate alternatives. Hydraulic filling with Portland cement added has shown considerable promise, but little has been done to define the parameters of design effective system. The purpose of this study is to determine the relationship between backfill and mining components that can be used to effectively design a best-case hydraulic backfill.

Jan 1, 2000

By Z. Ruetz

Portable X-ray fluorescence (pXRF) analysis has been widely adopted in the geochemical and environmental field as a cost-saving alternative to standard analyses. This paper outlines the efficacy of a method for indirectly quantifying organic copper content in solvent extraction circuits via stripping of the chelated metal with concentrated sulfuric acid in a single contact and subsequent pXRF aqueous analysis. pXRF analysis is common within the mining industry but presents unique challenges with liquid analysis, the most prevalent of which are briefly discussed. This method was developed specifically for mining operations with regional constraints and limited resources. Providing an in-field alternative to flame atomic absorption spectrophotometry and inductively coupled plasma optical emission spectroscopy, this entirely mobile XRF analysis method produces consistent and accurate results within minutes and at a fraction of the cost.

Jan 1, 2023

By ALBERT C. RUBEL

RECENT developments in the use of the core barrel in rotary drilling have led to its wide application in all types of development. Its use is essential to the wild-catter and a valuable guide and check even in the most closely developed areas. A perfect core would be an unbroken sample of formation whose length is equal to the amount of hole made by the core barrel, whose diameter is great enough to show the lithologic character, texture and attitude of the material encountered, whose formation is so unaltered in character and so free of contamination from outside sources that it represents a true and complete sample of the formation penetrated. From such a core it would be possible to determine the lithologic character and economic importance of the formation, whether it is oil bearing or barren, the nature and attitude of the sands and shale bodies, valuable fossil evidence and other points which would assist in the correlation or in the selection of suitable points for water shut off or production.

Jan 1, 1924

By S. R. Krogh

In this investigation, a method to measure the basic characteristics of comminution has been developed. These characteristics are expressed by the three major comminution functions - crushing probability function, energy function, and breakage function. By testing three different minerals, quartz, calcite, and jasper, these three functions are determined. It is shown that the crushing qualities of a material can be valued by three constants which define the two first comminution functions. These two functions give the relation between particle size, probability of crushing, and the energy input.

Jan 1, 1980

By Cesimiro Fabian

The crystallite size of copper electrodeposits was determined by X-Ray powder diffraction analysis using a General Area Detector Diffraction Solution (GADDS) diffractometer. Crystallite size was calculated for copper thin films which were deposited on a 316 stainless steel rotating cylinder electrode (RCE) in the presence and absence of additive ?A?. The crystallite size was calculated from a corrected full width at half maximum (FWHM) of the [110] peak profile using the Scherrer equation. The test of significant difference on crystallite size was derived using Kruskal-Wallis method. It was found that in the absence of the additive the median crystallite size was 426, which decreased to 364 in the presence of the additive. As the additive degraded, the crystallite size increased to a size similar to that observed in the absence of additive.

Jan 1, 2003

By K E. Mudzanani, T A. M Msagati, D T. Maiga, T T. Phadi, M R. Letsoal, B M. Chabalala, S W. Limani

This paper addresses critical environmental, health, regulatory and scientific concerns related to gold mining activities in the specific area of Barberton, Mpumalanga, South Africa. The paper thus calls for informed decisions to be made by the authorities to safeguard both the environment and people’s health. The novelty of this study is based on its comprehensive nature of the simultaneous assessment of both cyanide and potential toxic elements (PTEs) in tailings, while taking into account their composition variability over time. By combining these aspects, it is then possible to provide a holistic understanding of the contamination risks associated with mining tailings and thus justify the need for regular monitoring and supervision to ensure compliance against regulatory limits. Additionally, this paper considered investigating the dynamic nature of tailings, which are subject to changes in their chemical composition due to exposure to weathering by various agents. In this study, the determination of weak acid dissociable (WAD) and free cyanide in tailings was performed using a validated method employing the South African Council for Mineral Technology (MINTEK) Laboratory Cynoprobe. The PTEs in tailings were determined by an inductively coupled plasma optical emission spectrometer (ICP-OES). The results revealed that the tailings contained primarily substantial amounts of PTEs, including Fe (87 566 to 37 800 mg/L), Cu (271 to 110 mg/L), Mn (2100 to 680 mg/L), Ni (400 to 390 mg/L), Zn (180 to 68 mg/L), Cr (645 to 510 mg/L), As (450 to 128 mg/L), and Pb (up to 35 mg/L). The cyanide concentrations in tailings varied between 0.20 mg/L and 0.26 mg/L for free CN (with a mean of 0.23 mg/L in water leaching), 0.23 mg/L to 0.28 mg/L for free CN (with a mean of 0.25 mg/L in alkali leaching), 0.24 mg/L to 0.35 mg/L for WAD CN (with a mean of 0.28 mg/L in water leaching), and 0.31 mg/L to 0.39 mg/L for WAD CN (with a mean of 0.35 mg/L in alkali leaching). The measured concentration of cyanide and the PTEs was compared to the minimum permissible levels enforced by the South African Department of Water and Sanitation (DWS) and the Water Research Commission (WRC) regulations that govern the disposal of hazardous constituents into the environment. Additionally, it was observed that the concentrations of contaminants in the tailings exceeded the acceptable minimum limits for hazardous waste exposure, posing risks to the environment and human health.

Apr 16, 2024

By Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"A Jet Diffuser Flotation Column (JDFC) is a newcomer flotation device whose operation principles similar with Jameson cell but it has an essential change in downcomer. By taking into account the hydrodynamic and fluid mechanic principles (Sahbaz et al. 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogenous dissipation of the bubbles in the separation tank. Thus the performance increase has been aimed for the coarse particles.According to theoretical results, obtained by the formula of Oteyaka (1993) showing the relationship between velocity gradient and maximum floatable size for the various contact angles, the d50 of quartz flotation of JFDC is about 240 µm and 310 µm for the contact angle of 50° and 60°, respectively. This result was verified by the experiments. According to the experimental results; d50 which was accepted the maximum floatable particle size of quartz flotation of JFDC was about 256 µm and 300 µm for the contact angle of 50° and 60°, respectively.INTRODUCTIONFlotation is a kinetic process used for separation of hydrophobic particles from hydrophilic particles. There are many different parameters affects the success of the flotation and particle size is one of them. While the flotation is very efficient for intermediate size, the efficiency of the process starts to decrease for both fine and coarse sizes (Trahar, 1981; Muganda et al., 2011). Therefore; researchers have tried to find a solution for the efficiency decrease in fine and coarse sizes by modifying the chemical condition and designing the new devices. For example, Jameson cell is a unique device for the fine particle flotation due to the suitable design and fine bubble producing (Jameson, 1988; Evans et al., 1995; Sahbaz, 2010). Because of this success operation the Jameson cell is applied more than 200 flotation plants in worldwide. On the contrary, the efficiency of the cell decreases for coarse particle flotation due to the turbulence occurred in the separation tank (Sahbaz, 2010; Cowburn et al., 2007). That’s why, new flotation device was designed in loboratory scale by Sahbaz, Oteyaka and Ucar in 2010s and it has been called as Jet Diffuser Flotation Column (JDFC) recently."

Jan 1, 2016

By R. Tanaskovic

The objective of study of climatic conditions in underground mines is to create a working environment suitable for normal development of operations. Disregarding the fact that the development of equipment and technology, especially during the past decade, made the work in underground mines much easier, it is observed, according to the number of professional publications, that increasing attention is devoted to the study of climatic operating conditions in mines of many countries. This indicates that the climatic operating conditions are closely connected with productivity, and in turn with mine production profitability, in addition to the protection of manpower health and working capabilities. Usually, the concept of unfavourable climatic conditions of operation implies increased mine air temperature and humidity and low air flow rate, resulting in impeded heat exhange between human organism and working environment. As known, above phenomena are present in deep underground mines where the heat problem exceeds the-problems related to other features of natural conditions of mining. On the contrary, unsuitability of climatic operating conditions in mines with shallower mining depths is manifested by inadequate heat, particularly during the cold winter period. The two stated aspects of unsuitable climatic operating conditions are not solvable only by mine ventilation, so the former case requires cooling and the later one heating of the air used to ventilate the pit, or part there of where the phenomena are manifested. Study of climatic operating conditions in mines is, due to the number of factors involved, a complex and time consuming task, and this was, among others, one of the reasons for inadequate study of these problems in many mines. However, it is evident that further development of mine production imposes the need to make the climatic operating conditions in mines similar to those existing in other activities, where increasing attention is being devoted to the improvement of these conditions. Development of mining industry in Yugoslavia, particularly over the past decades, caused several of our mines to approach mining depths where the heat regime has a major influence on climatic operating conditions. This imposed the need to determine and investigate heat regime parameters, especially those that cause unsuitable operating conditions. The results of such investigations in the case of the deep part of Lead and Zinc Mine "Trepca" - Stari Trg are briefly reported in this paper.

Jan 1, 1980

By Juan M. Antorena

A pile driving and testing program was undertaken to evaluate installation procedures, assess capacity, particularly in uplift, of 360- and 460-mm (14- and 18-inch) square prestressed concrete piles and provide foundation design parameters for the New Mid-Point Bridge project in Fort Myers, Florida. Nine piles were dynamically monitored during installation, and six piles were monitored during restrike driving to evaluate pile drivability and uplift and bearing capacity including time related capacity increases due to soil "set-up". In addition, two static load tests (tension and compression) were performed to calibrated the results obtain during the dynamic testing. This paper presents descriptions of the pile driving testing program along with findings regarding pile uplift and compression capacities from the static load testing, pile capacities from dynamic testing (CAPWAP® analyses), soil-pile adhesion values, wave equation factors, soil strength vs. time dependency, foundation design (anticipated pile tip elevation) and pile driving recommendations.

Jan 1, 1995

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By A. J. Weinig

The method described is a modification of Schutzenberger's whereby the solution in titrations and the standards are protected from the atmosphere by a layer of kerosene. Indigo-disulfonate is the indicator and sodium hydrosulfite the standard. The method is rapid and delicate. It has been tried on a variety of mill solutions and mill men have found the method of value. THE important part that dissolved oxygen plays in the cyanide treat-ment of gold and silver ores is commonly recognized by most metallurgists and mill men.. But heretofore there has been no simple method on which the mill man could rely for determining the amount of oxygen in the various mill solutions. A few methods are adaptable to the, laboratory, such as the gasometric1 determination by actually measuring the oxygen. Winkler's2 iodometric method, and Schutzenberger's3 method, which depends on the reducing action of sodium hyposulfite on a blue solution of indigo carmine; but these are not readily adaptable to the needs of the mill man and cannot be applied to cyanide solutions without modification. The gasometric method is the most accurate but it takes too long to complete a determination. White's' method (a colorimetric method that depends on the degree of coloration imparted to a solution of pyrogallic acid in the presence of caustic soda) although much more rapid than any of the methods named, often gives misleading results on account of grading of colors of different solutions, which nearly always contain various kinds of salts. The method herein described was devised for the use of the mill man, the aim being to develop a simple, practical, accurate method. It is a modification of the Schutzenberger method and depends on the reducing

Jan 8, 1924

By R. L. Castro

Currently, in several caving operations, the spacing between the drawpoints is determined by consulting Laubscher's design guide (Laubscher 1994, 2000), a methodology based on the gravity flow characteristics of the caved rock. Laubscher's methodology is based upon the height of interaction between adjacent flow zones, but does not allow calculation of primary recovery for a given layout. In this paper the authors present a technical and economic methodology based on the flow that occurs near the drawpoint and the associated development costs to estimate the optimal spacing. The flow model at the drawpoint was validated at the El Teniente mine, which extracts coarse caved rock. To validate the flow model, small-scale simulations using drawpoint clusters were conducted and results compared to extracted grades, marker recovery, and drill holes to determine ore remnants that are part of the production control programme at the mine. The results indicate that primary recovery depends on the height of interaction, which varies with the friction angle of the caved rock and the spacing between adjacent drawpoints. Primary recovery estimations indicate values from 85 per cent to 97 per cent depending on the drawpoint spacing used. Extrapolations were then conducted to estimate the primary recovery for different drawpoint configurations planned to be used in the New Mine Level of the mine. The results indicate that the optimal drawpoint spacing is 32 m x 20 m with a through length of 18 m. The methodology developed may be used to estimate optimal drawpoint spacing for block caving mines under different metal prices and mine cost conditions.

Jan 1, 2012

By M. C. Ruiz

In the present study, the size distribution, Fo(v), of organic drops produced in a continuous-mixing vessel has been determined experimentally for various conditions. The organic phase used was a 1: 1 mixture of a salicylaldoxime (LIX 860N-IC) and a ketoxime (LIX 64-IC) in an aliphatic diluent (Escaid 103). The aqueous phase was a copper sulfate solution. The results indicated that an increase in stirring speed, extractant concentration, and pH produced smaller drops. The effect of the stirring speed was the most significant, decreasing the average volume of drops by 57 % for a change from 300 to 400 rpm. On the contrary, an increase in the dispersed phase fraction, copper sulfate concentration, and retention time produced larger drops. Changes in temperature from 23 to 30°C did not affect significantly the drop sizes. In all cases, the experimental drop size distributions could be accurately represented by a lognormal distribution.

Jan 1, 2001

By J. Moore Samuel

INTRODUCTORY BEFORE the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure, that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed "chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing the same, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 6, 1916

By J. Moore Samuel

THE CHAIRMAN (WALTER DOUGLAS, NEW YORK, N. Y.).-Perhaps there is no problem that causes the modern metallurgist more worry than the question of unaccounted for loss. He has not the advantage of the metallurgist of the early days here, who could sleep peaceably with the settled conviction that there were certain copper mineral constituents of the ore which were volatile, and there was therefore nothing to worry about. The slag contents and volatilization accounted for the balance of the copper that went in the top of the furnace after the weighing of the bullion. There have been great strides in recent years toward reducing this loss. Perhaps the Anaconda company is the one we have to thank for the original pioneer work along the lines which we are all today following. We would be glad to hear from some gentlemen present with reference to their experience with this question of dust losses. E. P. MATHEWSON, Anaconda, Mont.-You mentioned the Anaconda company, Mr. Chairman. I would like to say something about what we have been doing there, and the troubles we have been having. We have a tremendous volume of .gas to handle. We adopted the system of large chambers, lessening the velocity of gases, and incidentally cooling the gases. Unfortunately in one sense and fortunately in another, we were compelled to increase the amount of gas handled in the flue system, and the results were then not so good. Still, we get a very good recovery. Our system of taking a sample is similar to the one described by the writer of the paper. We have tried all kinds of apparatus for getting a fair sample. We divided the area of the flue into imaginary squares, and have taken samples for a certain period of time from each square; and have used the asbestos bags. At present, there is a large unit of the Cottrell apparatus almost ready to connect up on the roaster flue to catch the dust from flotation concentrates. The worst things smelters have to handle at the present clay, they are coming in the Southwest as well as the Northwest, are of material much of which is as small as 500 mesh, and the ordinary methods of catching dust will not apply to flotation concentrates. The Cottrell process is going to be tried out at our plant for this material. We have devised special forms, with a view to preventing the formation of dust from this material, and we are pleased with the results so far obtained. There is another point in connection with this subject that I want to put before the members here, so they will be thinking about it. You know there has been a great deal of litigation between the farmers

Jan 12, 1916

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991