Search Documents

By Mónica P. Arenas

Aços austeníticos resistentes ao calor apresentam propriedades mecânicas que permitem seu uso em altas temperaturas e pressão, sendo frequentemente utilizados em fornos de reforma e pirolise. Devido às severas condições de operação danos de carburização podem ser induzidos. No presente trabalho foram analisados corpos de prova provenientes de fornos de reforma que apresentaram baixos níveis carburização. Com a finalidade de desenvolver uma metodologia que permita detectar e separar diferentes níveis de carburização, foi projetado, simulado e construído um sensor magnético constituído por um yoke e um sensor Hall. De acordo aos resultados obtidos, concluiu-se que o sensor permitiu determinar confiavelmente o nível de carburização em ligas austeníticas que estiveram expostas a diferentes temperaturas de operação.

Oct 30, 2017

By Volney Viana Nogueira

A recirculação interna de gases em bombas de vácuo é uma falha frequente em estações de desgaseificação de aço e está associada ao aumento dos tempos de processo, a um maior consumo energético e a não obtenção da pressão de trabalho adequada. O tratamento de tais desvios pode ser complicado pela falta de informação disponível sobre os modos de falha dos equipamentos. Este artigo descreve um método experimental para encontrar valores de referência para testes que podem ser realizados na planta para a detecção de não conformidades em bombas de vácuo constituídas de ejetores a vapor e condensadores; tal método é composto por testes lógicos, sequenciais e não intrusivos. São fornecidas tabelas com os valores esperados das grandezas testadas, assim como diversas causas de redução de desempenho e de perda de função dos componentes.

Oct 30, 2017

By Tracy Morris, Weldon Read, Luis Navarro

"During the leaching of anodic slimes, tellurium dissolves into the leach liquor together with copper and must be removed before the solution is sent to liberator cells for copper recovery. Prior to the installation of autoclaves, tellurium was precipitated using raw slimes that caused a recirculation of tellurium in the leaching circuit. After autoclaves were installed the old leach tanks were converted into tellurium reactors utilizing copper chips, steam and agitation to form a copper telluride precipitate. Tellurium levels of less than 10 rng/L are achieved in a timely manner.IntroductionThe electrolytic refining of copper consists of an electrolytic cell provided with an anode of impure copper, a cathode of substantially pure copper (starter sheet) and an electrolyte made of copper sulfate and sulfuric acid [1]. When a direct electrical current is passed between the anode and cathode inside the cell, the impure copper anode dissolves in the electrolyte and pure copper is plated onto the cathode. During this operation, many of the impurities are deposited on the bottom of the cell as an anodic slime residue composed of insoluble chemical compounds. Slimes are a major source of rare and precious metals in the copper industry [2-5],In the Amarillo Copper Refinery (ACR), the anodic copper slimes are sent to the Precious Metals department in order to extract and then refine the gold, silver, platinum and palladium from them. The remaining impurities, in the form of a soda slag or copper slag are sent to the Hayden smelter for further processing. Copper telluride is sent to the Selenium/Tellurium department inside the plant for selenium and tellurium recovery. During the leaching process of the anodic slimes, copper, tellurium, and other metal species in the slimes are dissolved into leach liquor that cannot be returned to the tankhouse unless the tellurium concentration is below 10 mg/L."

Jan 1, 2012

By W. J. Fotheringham

This paper deals with the mining techniques employed at Canada Tungsten's northern Canadian operations, particularly with respect to their effect on productivity, safety, and stability of relatively large underground openings. The ore body was originally mined commencing in 1974 using conventional pneumatic jumbos in a topslice and horizontal benching room and pillar layout. Pillar stability became an increasing problem as mining progressed, leading to a re-examination and ultimately a conversion of mining method. Rock mechanics considerations and the effect of extraction rate on ground control costs and conditions are analyzed. Other areas discussed concern the results acheived through the use of large diameter I.T.H. drills, radio remote controlled L.H.D. units, and a unique system of hydraulic backfill placement.

Jan 1, 1985

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By Horace C. Porter

Much has been written of the changes undergone by coal in storage and the deterioration of coal through exposure to the weather. In order to obtain definite information for the benefit of the Government departments and of all who store coal in large quantities, a series of tests was begun in the fall of 1909 under the supervision of J. A. Holmes, then chief technologist of the United States Geological Survey, and was continued by the Bureau of Mines after its establishment in 1910. The tests were confined to determinations of the loss in heating value of the coals and did not include a study of other deterioration; for example, in coking quality or the yield of by-products in coking. The Bureau of Yards and Docks of the Navy Department cooperated in tests of New River (W. Va.) coal, a variety largely used by the Navy. A preliminary report presenting a brief account of the early results of these tests has been published by the Bureau of Mines as Technical Paper 16.a The detailed report is presented in this bulletin, which gives a full account of the tests and the analytical data covering a period of five years' storage. Data of somewhat similar experiments for shorter periods with gas coal from the Pittsburgh bed, with Pocahontas coal on the Isthmus of Panama, and with Sheridan, Wyo., subbituminous coal, which is used for railroad and other purposes in the West, are included.

Jan 1, 1917

FRANCIS B. SILSBE,* Washington, D. C. (written discussion?). ?This paper is an interesting example of the -solution by the methods of metallography of what seemed at first a purely chemical problem. The authors have shown: in detail, how the well-known corrosion of spark-plug terminals is due to the dropping out of the individual crystals of the metal as it becomes surrounded by an oxide film. This corrosion is usually quite slow but in special cases may become a serious factor in limiting the life of spark plugs. There still remains the problem for the metallurgist to produce a material that will be entirely free from, this trouble. One of the most startling results of the work is. the demonstration that it affords of the deleterious effect of a mechanical stress continuously applied to material that is at the same time subject to adverse chemical or thermal conditions. The particular style of spark plug shown in the illustration, and in which serious trouble was caused by this corrosion, has the side terminals fastened at both ends and the method of assem-bling is such that a considerable initial tension is applied to the wire. It is without doubt this superimposed tension that causes the inter-crystal-line network to line up, as it were, into a few continuous and deeply penetrating transverse fissures instead of forming a great number of shallow surface cracks. This result is clearly shown both in the case of

Jan 11, 1919

PAUL. D. MERICA, Bayonne, N. J. (written discussion*)..-The mode of intercrystalline oxidation which the authors" have so well observed and described is characteristic of nickel that has been exposed' to: the action of an oxidizing atmosphere at higher temperatures, such as, those at which; it is annealed or heated for rolling or forging. Oxidation under such conditions proceeds inward from the surface along the, crystal boundaries' producing a net-work, probably of oxide; which causes a very brittle condition of this surface material. This, in turn, generally results in surface cracking and checking during further, rolling and a defective sheet or other product is produced. An example of this is shown in Fig. 2, which shows the surface, of a badly surface-cracked sheet of nickel produced by incorrect heating con-ditions. A cross-section of this sheet etched with nitric acid is shown in Fig. 1, which reveals the intercrystalline oxidation network adjacent to both surfaces.These layers are so brittle that it is not possible to deform them by rolling without severe cracking along these lines or, planes of weakness. The best, and possibly only, remedy for this condition lies in its prevention by the maintenance of a neutral soft flame for heating and annealing nickel during the entire course of its manufacture. I should like to suggest that, those making microscopic investigations of nickel and nickel-rich alloys try the use of acetic-acid .solutions of nitric acid for etching these metals rather than aqueous solutions, of nitric acid. I have found that a solution containing 50 per cent. nitric acid, from 25-45 -per. cent. acetic acid, and from 25-5 per cent. water gives excellent results with. Wrought and cast nickel and Morsel metal and superior results to those obtained with nitric acid, alone. The acetic. acid seems to inhibit the passivity that nickel often assumes toward nitric acid and much more uniform etching may, be obtained. The proportions of nitric and acetic, acid may be varied somewhat from those given without mate-rially altering the quality of the etching, although without any distinct improvement in it.

Jan 12, 1919

By Enrique Cervantes

Durante mucho tiempo, las vetas angostas generaron inquietud para los operadores mineros - en tanto su morfología provoca una baja productividad, así como el aspecto técnico obliga a depurar sus sistemas. En ese sentido, el presente texto refiere el método de corte y relleno como el más adecuado para la explotación de vetas puesto que puede adaptarse a las características de este tipo de yacimientos, además del alto grado de flexibilidad para adoptar algún cambio de sistema.

Sep 1, 1982

By Armando Rivera, Ángel Cueva

El proyecto Mirador, ubicado en la provincia de Zamora Chinchipe en Ecuador, es un sistema mineralizado del estilo pórfido – cuprífero, tipo cobre – oro. Constituido por una zona superior de óxidos, adyacente a un área transicional de óxido –sulfuro dentro de una zona mineralizada con sulfuro hipógeno (calcopirita– pirita), tiene potencial para generar drenaje ácido de roca (DAR), lo que crea preocupación ambiental respecto de los recursos de agua superficial y subterránea. En este artículo se describen diferentes etapas de muestreos de los núcleos de perforación con variación en profundidades y litologías, el análisis de los factores que influyen en la transformación de residuos sulfurosos, y la realización de pruebas estáticas estándares y cinéticas.

Feb 28, 2019

By Medardo Echegaray

Desde el punto de vista de análisis químico se buscaba estudiar un método de determinación de fierro que ofreciese una buena precisión en una zona de concentraciones. En ese sentido, el presente texto señala la determinación colorimétrica del fierro a través del método de complejo aceto-férrico. No existe intlerferencia por el manganeso, fluor o níquel. El cromo interfiere cuando se encuentra en cantidades mayores a su máxima concentración permisible o sea 0.1 mg .

Mar 1, 1963

By Medardo Echegaray R.

El presente texto señala la utilización del complejo acético para la determinación colorimétrica del fierro en la industria. De acuerdo a los estudios realizados anteriormente, se encontró que el método es simple, rápido, económico y exacto en su proceso y aplicación de muestras ambientales. Las condiciones óptimas de trabajo requeridas son que las lecturas deben efectuarse a 465 mu, la zona de máxima exactitud está comprendida a 2 y 30 mg. de Fe, el color correspondiente al complejo sigue la ley de Beer en el rango indicado, la curva de trabajo es reproducible, el color es estable y el pH puede variar de 3. 5 - 4. 4 sin afectar el resultado. Finalmente, no existe interferencia por el manganeso, fluor o níquel, pues el cromo solo interfiere cuando se encuentra en cantidades mayores a su máxima concentración permisible (O. l mg).

Jul 20, 1961

By Wolfang Schoeps

El presente texto describe los factores para determinar la cantidad correcta de compras en los artículos de diversas empresas a través de los costos de un pedido de compras; los costos de almacenaje y los descuentos progresivos de cantidad.

Jul 1, 1960

By Adolfo Pillihuaman, Javier Montalvo, Adriana Virrueta, Alberto Aguilar

"El presente trabajo estudia la lixiviación de un mineral oxidado de cobre en una solución acuosa de amonio, con el objetivo de obtener las condiciones óptimas de lixiviación del cobre contenido en el mineral malaquita. El mineral de cobre estudiado es proveniente de un yacimiento del sur del Perú y fue caracterizado por difractómetro de rayos-X, ICP-OES y Absorción Atómica."

Sep 1, 2017

By Ronald Benito

El presente texto señala el algoritmo basado en grafos como la técnica que determina el límite óptimo de minado a cielo abierto. Por ello, se adaptó la técnica de Lerchs y Grossmann y intermedias (algoritmos) y fue usada para crear nodos, arcos y estructuras de árboles en tablas para determinar la máxima cerradura de un grafo.

Sep 1, 2013

La protección de la salud del minero es la principal labor de la higiene industrial donde se requiere la cooperación de múltiples disciplinas como la medicina, ingeniería y química. En este sentido, el objetivo del texto señala la técnica de determinación de elementos tóxicos (plomo, cadmio y zinc), a través del uso de un método electroquímico denominado polarografía. La polarografía es un microelectrodo de forma de capilar que destila mercurio eun solución colocada sobre una celda, desde donde se aplica un potencial contra un electrodo de referencia, para luego ser medido por la corriente fluída a través de la celda. La implicancia de este método polarográfico estriba en el empleo del cloruro de calcio como elemento separador del oxígeno y auxiliar en la concentración de metales pesados en una sola muestra. De forma que, se pueden concentrar grandes cantidades de metales sin alterar o requerir grandes disoluciones. En consecuencia, la eficacia del método responde a una fácil confrontación o chequeo con la curva standard determinante de los datos.

Jul 20, 1957

By Otto Sandovel Zea

El compromiso de minería perfecta se limita no solo a la preservación del medio ambiente, sino a la prevención de riesgos por desprendimiento de rocas y aplastamiento en el interior de la mina. En ese sentido, el presente texto señala la factibilidad de minar a sección plena todos los tajeos a través de la simulación de las condiciones más favorables y desfavorables de la mina, determinando como la alternativa más viable la bóveda en arco. Dicha estructura otorga estabilidad a las labores de minado -en tanto da sostenimiento activo a través del (Shotcrete SFR y Pernos Hydrabolt), así como desarrolla mayor productividad y menores niveles de riesgo por desprendimiento de rocas, menores grados de sobre excavación y genera de vibraciones al haber implementado la voladura de Pre-corte en sus labores.

Sep 12, 2011

By J. C. Barcellos

El presente estudio describe el método de empleo para la determinación del espaciamiento óptimo de muestreo en la Mina Casapalca. La técnica comprende cuatro pasos: recolección y preparación de datos, procesamiento electrónico de datos, análisis de los resultados y la verificación de las conclusiones. Dentro de las conclusiones, se considera que los métodos estadísticos son los más útiles en la solución de los problemas de la industria minera , puesto que cualquier dato numérico pueden ser convertido a un número más simple a través de la computadora.

Nov 20, 1972

By Luis Huere

La calcopirita es uno de los minerales de cobre más difíciles de lixiviar. Si bien es posible generar un PLS en un medio muy oxidante, las recuperaciones son muy bajas como para considerarlo una alternativa de procesamiento de esta mena de cobre. Con el objetivo de elevar la recuperación de cobre en el PLS obtenido, en este estudio se realizaron diversas pruebas de lixiviación de un mineral de cobre calcopirítico para determinar los mejores parámetros de lixiviación que produzcan la mayor recuperación de cobre en el PLS que se dirige a la extracción por solventes y electrowinning respectivamente. Se realizaron prueban con oxidación por ozono, sulfato férrico, ozono-sulfato férrico, sulfato férrico-ozono y sulfato férrico con temperatura elevada. La prueba con mejor resultado fue la de sulfato férrico, pues produjo la mayor recuperación de cobre.

Sep 20, 2019

By Luis Torres Yupanqui

Dado que en el diseño de labores mineras subterráneas y superficiales se considera la caracterización del macizo rocoso a través del levantamiento litológico estructural (modelo geológico), el presente texto busca describir la cantidad de valores relacionados con la durabilidad de la roca, contrastando de acuerdo a la clasificación Geomecánica de Bieniawski el valor de la meteorización, determinando la calidad del macizo rocoso.

Dec 1, 2015