Search Documents

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.

Jan 1, 2018

By Kevin G. Stricklin

Introduction Continuous monitoring techniques have been used in the US and abroad for many years. A continuous miner has a monitor that measures methane and automatically gives a warning if the methane exceeds 1%. It deenergizes the continuous mining machine automatically at a maximum concentration of 2%. Main fans are also continually monitored to ensure operation. Alarms may also be given at a remote location should a fan slow or stop. The systems being developed can continuously monitor various gases and equipment throughout the mine and transmit pertinent data to a surface monitoring station. At this station, conditions throughout the mine can be monitored and, in some instances, controlled. These are known as Mine Wide Monitoring Systems (MWMS). History The use of environmental monitoring systems began in 1976 when a federal court approved the petition of modification to use belt air at the face. The first mine to receive a modification did install a system to supplement existing safeguards. Later, the Mine Safety and Health Administration (MSHA) and the US Bureau of Mines (USBM) conducted tests dealing with the use of belt air. Findings from these tests are being used to set guidelines as requirements of a petition. These requirements include: • Velocity of air has to be 0.25 to 1.5 m/sec (50 to 300 fpm); • Monitors will be installed at each belt drive and tailpiece and at intervals not to exceed 610 m (2000 ft); and • An alarm level of 10 ppm, above the ambient level is appropriate. The early uses of environmental monitoring could only be used outby the last open crosscut. That may be a reason for an initial slow growth of these systems. In June 1982, MSHA began evaluating systems that could be used in returns to ensure that monitoring systems being used in areas where permissible equipment is required does not of itself pose an explosion hazard. This is known as the Mine Wide Monitoring Systems Evaluations and Sensor Classification program. The evaluations and classifications granted are based on electric currents and voltages. Use of mine wide monitoring systems The environmental aspect of MWMS in today's coal industry deals with carbon monoxide (CO), methane (CH4), and air velocity. Just as all mines are different and encounter different problems, the MWMS are diverse and can be used to provide necessary data in all areas of coal mines. Mine operators in an ultragassy seam, for example, may be concerned with monitoring methane, while a mine that used diesel equipment may want to continuously monitor for diesel contaminants. In a mine with roof fall problems, airflow monitors may be helpful as an indication of whether the air is flowing in its normal course and at its normal volume. Today's MWMS can monitor any or all of these parameters. Most systems can be expanded as mining needs require. For example, a mine is now being monitored for methane and five years from now CO monitoring would help increase safety. It may be possible to use the same system by adding additional equipment. In the US, 30 environmental monitoring systems were installed from May 1985 through May 1986. In 1984 and 1985, there were 38 and 44 environmental monitoring systems in operation, respectively. Due to mine closings, 11 of these are no longer in use. However, the number of mines using environmental monitoring systems increased to 63. Use of these systems are not limited to any geographic area or

Jan 9, 1987

Earth Sciences: The standard of living of the world's people depends upon human initiative, investigation, and know-how in exploiting the earth's resources. The Earth Sciences-geology, mineralogy, geophysics and geochemistry, meteorology, geography-are basic sciences dealing with those problems concerning the origin, constitution, and utilization of the earth's materials. The development of these fields in one department provides the greatest opportunity for direct contact and stimulus for scientists and teachers working in related fields. In the Earth Sciences, geology and mineralogy are obviously closely related. As rocks are the materials of which the earth is made, so in turn minerals are the constituents of the rocks. Conversely, a study of earth structures and the interplay of physical and chemical forces in the earth is necessary in order to understand the origin and source of minerals. Building on the basic core of knowledge of earth processes, earth structures, and earth history, the geologist will continue to push out the frontiers of stratigraphy, structural geology, pale-biology and petrology with growing insight into principles that control surface and subsurface rock conditions. As the field of geology has advanced, several lines of specialization have developed. The economic geologist

Jan 1, 1950

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By Jasper D. Ward

The Indiana Limestone Company has developed an insulated, thin and comparatively light-weight pane 1 suitable for use as a spandrel panel in a curtain wall. The panel is about four inches thick and is composed of limestone backed with insulation. The inner surface of the insulation is protected with asbestos-cement board or a metal pan, depending on the type of insulation, building-code requirements and appearance (if the surface is left exposed). The limestone is cut to the size of the spandrel openings and the insulation and backup is applied in the mill ready to be shipped and in- stalled in the wall grid, A mortarless and waterproof joint with the metal frame components is achieved through the use of neoprene, thiokol, and caulking, The limestone is "dirt-proofed" (waterproofed) in the mill to slow down discoloration. The panel weighs more than some presently used materials. However, ILCO's architects and engineers have found that curtain wall systems capable of withstanding imposed wind loads are made up of sections large enough to carry this extra load of stone with little or no modification to the size of the metal frame. Limestone, a traditionally sound material, can be used in this new way without losing any of its natural qualities of dimensional stability, resistance to fire, and permanence.

Jan 1, 1959

By AIME

To be born in the East, reared and educated in the West, to do graduate work in Germany, leading to the doctorate in metallurgy, and to wind up-for the time being at least-in the Middle West as head of one of the outstanding mining and engineering schools of the country, is a unique career. Curtis Laws Wilson, dean (and in most respects, president) of Missouri School of Mines and Metallurgy at Rolla, is a native of Baltimore. He came to Anaconda in 1918 and in due course was graduated from Montana School of Mines, with an exceptional record. In 1921, after experience in metallurgical research at Anaconda, he became instructor in metallurgy at his alma mater. Because of his ability as a teacher, he rose rapidly to head of the department after special work at Columbia in 1923-24. In 1927, Wilson was granted leave of absence to study physical metallurgy under the great Tammen at Goettingen, and returned with his doctorate to his work at Montana School of Mines. His major metallurgical interest was then in age-hardening of copper alloys. Also after his return to Montana Mines, Wilson started

Jan 1, 1948

By Jetson Lemos Ferreira

O presente estudo teve por objetivo verificar a independência tanto da Curva Limite de Tensão (CLT), quanto da Curva Limite de Deformação Plástica Efetiva (CLDPE) em relação à trajetória de deformação. Para tal, foram utilizadas Curvas Limite de Conformação (CLC) de aço livre de intersticiais (Interstitial Free - IF), determinadas, primeiramente, por meio de trajetórias lineares e, posteriormente, por trajetórias bi-lineares estabelecidas por níveis de pré-deformação nos modos de tração uniaxial e estiramento biaxial simétrico. As previsões da CLT e da CLDPE, calculadas a partir das deformações limites da CLC convencional em trajetórias lineares e bi-lineares, mostraram-se independentes em relação à trajetória de deformação. Entretanto, verificou-se que o critério de escoamento adotado tem grande influência na forma e posição destas curvas limites.

Aug 17, 2017

By T. T. Wang, T. H. Huang, S. S. Zhan

"Fractures with diverse features dominate the hydraulic behavior of fractured rocks and are one of the major subjects for hydrogeological characterization of a site. This study investigates curve patterns obtained by packed tests, and as well the influence of fracture features based on 59 sets of in situ packer tests with different fracture combinations and fracture features. The result shows that, in the example of Heshe site, neat and tidy fractures usually provide stable channel for water flow during testing, and the hydraulic properties of fractures infilled with breccia and mud may change during testing because of leaching and/or washed out of infilling breccia and mud. Different combinations of fractures with diverse features in packed test sections lead to different curve patterns for in situ hydrogeological tests. For groundwater flowing predominately through neat and tidy fractures, the pressure-discharge curve of modified Lugeon tests are usually linear curve pattern, and the pressure decrease while the discharge increase in pressure-discharge-time curves of single-hole double packer tests, which benefit statistically determining the transmissivity of dominant fracture sets. INTRODUCTIONFractures interlaced in rock masses are major channels for groundwater flow and generally account for the anisotropic and heterogeneous characteristics of permeability for fracture rocks. To describe reasonably the permeability of a fracture rock, the Discrete Fracture Network (DFN) approach and others with similar ideals have been developed. Many methodologies and associate equipment, for instance, the televiewer and the in situ hydrogeological test, have been proposed to investigate the spatial distribution and the transmissivity for different fracture sets, which are two main parameters necessary for the DFN or similar model simulation (Pearson & Money, 1977; Barker & Black, 1983; Hsieh et al., 1985; Bernard et al., 2006; Quinn et al., 2012). However, diverse outlooks for the pressure-discharge curves and the temporal pressure and associate temporal discharge curves often confuse the investigation results by significant deviations on derived permeability (Houlsby, 1976; Zlotnik, 1994; Royle, 2009; Camilo, 2010).Aiming on technical development for in situ hydrogeological tests and fracture investigation, an experimental well site with 10 wells has been established in Heshe in central Taiwan since 2011 (Wang et al., 2011; Song, 2012; Zhan et al., 2013). Extensive geological survey and well-hole scanning by a televiewer provide spatial distributions and outlooks of fractures in detail. Additionally, a series of Lugeon tests, double packer injection tests and pumping tests have been performed to investigate the permeability of fracture rocks, and dominate fracture sets as well. Based on the results obtained from the Heshe site, this study classifies the curve patterns of hydraulic packer tests. The features of fractures involved in packed sections for packer tests are then inspected in detail. Relationship between the curve patterns of hydraulic packer tests and associated features of corresponding fractures in rock are discussed and addressed accordingly."

Jan 1, 2015

By Allan Rocas, Aswathy Sivaram, Daniel Cressman, Tatiana Chiesa

The City of Toronto plans to construct a 1,350 mm consolidation sewer along the East Don Roadway (EDR). The project includes installation of approximately 260 meter of 1,350 mm diameter concrete pressure pipe through microtunneling methods. The sewer alignment crosses underneath a busy 5-lane arterial road and then follows the very narrow East Don Roadway road allowance. This paper discusses the significant challenges overcome to design the Don Roadway sewer using slurry microtunneling methods through mixed face conditions below the groundwater table in a congested road allowance. A curved microtunnel was ultimately required to avoid conflicts with existing utilities, condominium tiebacks and a bridge structure.

Jun 13, 2023

By D. Royston

Curved pulp lifters have been incorporated in SAG and AG mills in Australia. The aims have been to ensure complete discharge, at high throughput, of both slurry and coarse solids, especially at high mill rotational speeds. Curved pulp lifters can overcome incomplete discharge and back-flow of solids down the pulp lifter that can occur in straight-radial pulp lifters (and is a major cause of wear). They can be designed to prevent reverse flow of pulp via grates back into the mill. Experience with curved pulp lifters now extends to three years over three mills, in one mill as an installation from new and two as retro-fitted installations. Curved pulp lifters, relative to conventional designs, offer improved discharge and wear performance and well as high impact-resistance and wear life of the curved pulp lifter grates.

Jan 1, 2000

By R J. Soriano, S Ciutina

The Masbate gold deposits are situated on the island of Masbate, 350 km south of Manila. A new plant was commissioned in April 2009. The grinding circuit consists of one semi-autogenous (SAG) mill Ø9.75 m × 4.27 m, two ball mills Ø5.6 m × 7.1 m and a pebble crushing circuit, which is usually called a SAG-ball mill-crusher configuration. The SAG mill was originally equipped with radial pulp lifters. The mill runs at fixed speed of 10.9 rev/min, which is approximately 80 per cent of critical speed (per cent CS). Due to the high speed of the mill the original radial design pulp lifters presented a high volume of recirculating load inside the chamber and consequently heavy wear on the outer circle (bottom pan).In order to address the high wear on the pulp lifters a number of avenues were considered in early 2011. The chosen solution was to change the geometry of pulp lifters from radial to curved design. The pre-existing drilling pattern on the discharge end of the mill was a major constraint. A number of designs were considered. The selection of the most suitable option was to be made based on 3D discrete element modelling (DEM) and smoothed particle hydrodynamic (SPH) simulations.The original radial design and two potential solutions for curved pulp lifters were simulated with 3D DEM and SPH software. The main three objectives were predicting the charge dynamics, the expected wear patterns and discharge efficiency. One of the solutions was chosen and implemented during 2012.Observations carried on after installation of the curved pulp lifters have confirmed, as expected, a reduction in wear intensity on the outer pulp lifters. In addition to this, at early stages of operation with curved pulp lifters, the mill operator noticed a reduction in energy consumed by the mill with no detrimental effect on mill performance.This paper is intended to further study the effect of curved pulp lifters on mill energy consumption.CITATION:Ciutina, S and Soriano, R J, 2014. Curved pulp lifters – can they save energy?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By C. R. Kuzell

INTRODUCTION KNOWLEDGE of the thermal capacity of gases is of great importance in making metallurgical calculations. The metallurgist is, frequently called upon to investigate and determine furnace efficiencies in which the heat carried into or out of the furnace by gases is a large item in the heat balance. Not only do such problems present themselves in the determination of furnace efficiency, but also in the study of the application of heat is accessory apparatus, such as stoves, regenerators, waste-heat boilers, driers,.etc. The thermal effect of the use of excess air in the combustion of fuel, the theoretical temperatures of combustion, the quantity of heat in hot blast at various temperatures, the effect of hot blast on furnace temperatures, are a few more examples of frequently occurring calorific problems involving gases. So many are the applications of the data on the heat capacity of gases that the subject merits careful study. The heat in a gas maybe due to its heat of combustion, if it is a combustible gas, and to its temperature. The latter is called its sensible heat and is the heat absorbed or evolved by a gas as its temperature is raised or lowered. The heat of combustion of gases is well established and is commonly known. The values can be found in almost any mcdern treatise on metallurgy. The sensible heat of gases has not been so well established because it is in most cases a function of the temperature, and the values of specific heats of gases over a wide range of temperatures have only recently been determined. It is the purpose of this paper to deal with the sensible heat of gases.

Jan 8, 1914

By C. R. Kuzell

The Editor desires to call attention to the charts in the paper of the above title which were published in the August Bulletin on pages 2190 and 2191. It was impracticable to include in the Bulletin. charts of sufficient size to be used as working diagrams for the direct determination of operating values, but the Institute is prepared to furnish copies of these charts on a large-size scale, at a moderate cost, to those who desire to have them for this purpose. CORRECTIONS Page 2185, line 3. For "is accessory apparatus" read "in accessory. apparatus." Page 2188. Substitute for lines 11 and 12: Nitrogen, oxygen, carbon monoxide, Cp = 6.50 + 0.0010T Hydrogen, Cp = 6.50 + 0.0009T

Jan 9, 1914

By C. S. Parsons

Custom milling-plants have been operated successfully for a great many years on this continent. One of the outstanding examples in the United States is the Golden Cycle mill at Colorado Springs, which mills the gold-telluride ores from the Cripple Creek district. In eastern Canada, the Northern Custom Concentrators, Limited, at Cobalt, successfully treated the cobalt-silver ores of that area for a number of years. Flotation plants have entered the custom field in the past few years. The building of flotation concentrators to treat ores on a custom basis indicates the advance which has been made in flotation. In fact, three years ago it was considered almost impossible to treat successfully a mixture of miscellaneous ores by flotation. The methods used at that time were considered so delicate that any change, even in a single ore, would usually result in decreasing the effectiveness of the separation. Today we find four large custom flotation plants in the United States and one in Canada for treating complex lead-zinc ores from many different localities. The advent of these mills was brought about by the serious problem confronting the lead-smelting plants due to increasing amounts of zinc in the ores presented for treatment. It was necessary to penalize the mines shipping high-zinc ores. The penalty is justified, because high zinc in the lead blast-furnace charge not only decreases the tonnage of the furnace but increases the amount of flux necessary, as well as increasing the metal loss in the slag. It has been estimated that in the Salt Lake valley alone, 75,000,000 pounds of zinc was lost in the slag-dumps from the operations of three large lead blast-furnace plants. It has also been estimated that $150,000 worth of additional flux was required to slag this zinc. It was to avoid at least a part of this wste and to help maintain an ore supply that custom flotation concentrators were built by the smelters.

Jan 1, 1928

By Michael T. McCaffrey

The wide range of potential feed materials, process steps, and products in metallurgical facilities means that standard equipment might not be available to adequately meet the project technical and economic needs. Custom designed equipment should be considered only after rigorous research precludes purchasing standard equipment. However, the decision to use custom equipment introduces a new element of risk into the project. To manage the risk, custom equipment design should be developed through the same front end loading (FEL) phases as project development. If more than incremental development of custom equipment is required, appropriate test work or pilot trials are required to test key uncertainties. Important activities during custom equipment design include maintaining clearly defined performance objectives, conducting appropriate reviews, carefully crafting commercial and intellectual property agreements with design and fabrication partners, and assembling a multidisciplinary team with sufficient development expertise.

Jan 1, 2015

By R. B. Hopler

Explosives R&D has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. This process continues at an accelerated pace today due to the tools presently available to the explosives and mining industries.

Jan 1, 1993

By J. David Chapman

There are a variety of choices of materials for mineral extraction processing. Traditionally, end users have used metallic piping for fluid handling and little is known about the advantages (or limitations) of non-metallic piping systems. This presentation will review custom FRP pipe systems and their use in severe corrosive and erosive process streams. These systems can be designed to various pressure and temperature ratings and different components (such as resin and glass type) can be varied to suit the process conditions

As Coal Mining Areas develop, problems relating to strata control increase. The "easy" coal has been extracted and the future development lies in the direction of greater depths of cover and more difficult strata conditions. To provide solutions to the problems encountered the techniques of constructing and testing physical models have been developed and refined. With a sound knowledge of model theory allied to practical experience, mining research engineers use physical cemented material models to examine, assess and solve mining problems relateu to strata behaviour and environment. For a model to provide the answer to a particular mining problem it is essential that as much information as possible be obtained from the mine or area of a mine which the model is to represent. Details relating to the strata, geological malformations, and the stress environment must be collected and collated to ensure reliable results.

Jan 1, 1976

By Robert B. Hopler

Explosives research and development has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. Today, this process continues at an accelerated pace due to the tools presently available to the explosives and mining industries. Background Explosives have been used in coal mining since the industry's earliest days. Black powder, introduced into metal mining in 1627, undoubtedly was introduced into coal as soon as a need to replace pick work was apparent. Until the invention of the safety fuse by William Bickford in 1832, the only initiation methods available were the straw, quill and miner's squib. Disastrous explosions underground in England brought about studies on their possible causes (Atkinson, 1886). The studies showed that, while explosives contributed to the accidents, the real villain was coal dust, since that was the agent that transmitted the disaster throughout the mine workings. To improve underground safety, research was applied in an attempt to make explosives that could be safely fired in a methane air atmosphere. The Prussian government was apparently the first to establish a testing station for coal mine explosives. This occurred in 1885 (Guttmann, 1909).

Jan 1, 1993

By Frank Barker

Mining operations present a very different environment to the suppliers of explosives, initiating systems and services, both on surface and underground. Typical hazards include underground movement, air quality, ground stability, moving equipment, and the use of explosives. As contractors to the mining industry we do not have management control over the environment in which our people operate. The hazards and consequent level of risk that our people are exposed to in some mining operations are significantly higher by orders of magnitude than in a normal factory environment. Orica Explosives (and other Explosives suppliers) are continually and increasingly identifying opportunities to partner with customers by adding value through the provision of services leading to a reduction in total mining costs. These services include the provision of a bulk underground loading services, delivery of product into underground magazines, magazine management, value added blasting, conversions, rock-on-ground contracts, and blast management programs.

Jan 1, 2000