Search Documents

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Variations of cut-and-fill stoping are the most com¬monly used methods for mining narrow, nearly vertical veins in the United States. These methods offer the best results for maximum recovery with minimum dilution of ore from veins that are irregular along either the strike or dip. The vein is developed along the strike length in 61 to 122-m (200 to 400-ft) blocks or stopes and vertical lifts of 48 to 61 m (160 to 200 ft). The level development is either on the vein or parallel to the vein with crosscuts intersecting the vein at right angles. Chutes, manways, and haulageways are established in the center of the stopes at the lower level of the ore block. Mining then proceeds by blasting down horizon¬tal cuts of the vein in both directions from the chutes. As the blasting continues to the outer limits of the stope, the broken ore is slushed into chutes. When a complete horizontal cut has been made, the service raise, including chutes, is raised to a height of a few feet from the back and the stope is filled with either sand fill or waste rock. Then the mining cycle is re¬peated until the stope reaches the level above. LEVEL DEVELOPMENT PRACTICES FOROVERHAND CUT-AND-FILL STOPING The two basic methods used are: the development of the haulage drift within the vein, or development of the haulage drift paralleling the vein in the foot or hang¬ing wall with crosscuts intersecting the vein perpendicu¬larly at 61 to 122-m (200 to 400-ft) intervals. The il¬lustrated methods of development show some of the variations which can be used to develop a stope block. Development for cut-and-fill stoping does not require the more elaborate schemes outlined for shrinkage or sublevel long-hole stoping. Many factors must be considered before deciding on a particular development plan and usually the nature of the vein or host rock will dictate which specific method to use. If the vein is relatively straight, then develop¬ment on the vein is feasible. Excessive ground pressures will necessitate the leaving of a sill pillar (Fig. la) and highly fractured or "heavy" ground will require timber¬ing (Fig. 1b). Development on the vein has the advan¬tage of reducing capital outlay and waste handling prob¬lems since the mined rock has value. But removal of the sill pillar is costly and time-consuming. Also, where no sill pillar is left, excessive timbering and subsequent level repair is a drawback. Development in either the footwall or hanging wall is the more common procedure and offers greater flexi¬bility in overall development of consecutive stoping blocks by partially disassociating the level development from stoping (Fig. 2). Chutes, manways, and service compartments com¬prise the next stage of development and are established in a variety of ways. They provide access to the stope, ventilation ducts, and muck removal. Several different development systems are in common use and average costs for each have been developed. Raise borers are used to establish ventilation and ac¬cess from level to level. They are normally reamed with 1.5 or 1.8-m (5 or 6-ft) cutterhead and may either be left bald or lined with a 1.2-m (4-ft) diam corrugated liner plate, depending upon ground conditions. The use of an Alimak raise climber is another effec¬tive method of driving a raise from level to level. The size usually is 2 m (7 ft) square. This will accommodate square-set timber which is later installed. This method of raising is not common, although it is a valuable tech¬nique especially when level spacing is several hundred feet.

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5'/z ft) in width, and 1.6 m (5'/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Shrinkage stope mining can be employed in steeply dipping veins where both the wall and the vein material are sufficiently strong to stand with only minimal ground support. Shrinkage stope mining takes advantage of the swell in volume produced in breaking in-place ore. This expanded volume of ore is allowed to occupy part of the mined-out vein, and in so doing provides ground sup¬port and a working surface for the miners. Only enough of the ore is drawn after each stoping cut to allow work¬ing room. Not until the entire mining block has been broken is the full amount of broken ore drawn from the stope. DEVELOPMENT PRACTICES FOR SHRINKAGE STOPING The vein is developed into stoping blocks, each of which is 76 to 91 m (250 to 300 ft) in length and 61 m (200 ft) between levels. Level development, described later, is either on the vein or parallel to it with crosscuts periodically driven over to the vein. There are usually two exits from each stope. The first entry is a raise at one end driven either conventionally by raise climber, or by a raised borehole. Present practice is that this raise, put in from level to level, is either a 2.1- x 2.1-m (7- x 7-ft) Alimak raise or a 1.2- to 1.8-m (4- to 6-ft) diam borehole. Either raise system will require pro¬visions for an ore chute carried with the stope to the haulage level or the scram drift. At 9- to 12-m (30- to 40-ft) vertical intervals, dogholes are developed from the raise so that when stoping breaks back into these dogholes, timber or steel sets and necessary service facilities can be installed. The second entry to the stope may be either a similar raise at the stope endline, or more economically, a cribbed raise carried with the stope. As previously stated, development of the ore block is achieved by either drifting on the vein or by paralleling the vein with a footwall lateral and then crosscutting over to the vein at specified intervals. In the following discussion, three basic cases are illustrated in Figs. 1, 2, and 3. In Fig. 1, development is in the footwall by a 3- x 3-m (10- x 10-ft) trackless lateral. A heading is also driven on the ore and taken either full width or driven a standard size and slabbed to the vein width. Approxi¬mately 9-m (30-ft) long crosscuts on 7.6-m (25-ft) cen¬ters are driven from the lateral to the vein. For ease in muck handling they are usually put in on a slant rather than at right angles. A single orepass, located off the lateral and in the center of one stope block, can serve not only that stope, but also one on either side, up to a tramming distance of not more than 137 m (450 ft). Raises are put at the stope endlines on 91-m (300-ft) centers. The back of the vein is shot down and just enough broken material is drawn off to permit access for men to work off the broken ore. Development in Fig. 2 progresses by driving a 3- x 3-m (10- x 10-ft) trackless heading on the footwall side of the vein. The ore block is delineated by raises on 91-m (300-ft) centers. Crosscuts are again driven on 7.6-m (25-ft) centers over to the vein. Approximately four rounds are then taken up to the vein and each round is successively belled out so that all the crosscuts (pockets, in this case) connect. In this development, as opposed to that in Fig. 1 where there were no belled

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982

By Yokozawa K, Yamamoto T, Kameoka Y

Japan Construction Method and Machinery Research Institute has been conducting various field surveys of tunnel works and other excavation works, and the cost and efficiency of these two excavation methods have been studied. Based on these data, the costs of blasting excavation and mechanical excavation represented by roadheaders were calculated. The costs were calculated and compared for rocks of various hardness. When the total construction cost is considered, the degree of overbreak becomes one of the most influencial factors, because the overbreak area must be filled up with expensive shotcrete in NATM. So, in the next step, the relation between the excavation costs considering overbreak and the rock hardness was studied using the data on overbreak obtained by the field survey.

Jan 1, 1987

By Carson Rife, Michael L. Clark

INTRODUCTION Zortman Mining Inc. is a wholly owned subsidiary of Pegasus Gold Corporation of Spokane, Washington. Pegasus has been producing gold and silver from the Zortman and Landusky mines since 1979. The Zortman and Landusky mines are two distinct open pit mines located approximately 6 kilometers apart in the Little Rockies Mining District of north central Montana. The two mines use large-tonnage, low- grade heap leaching techniques to efficiently process the gold and silver ore. PROJECT DESCRIPTION The Little Rockies rise abruptly 914 metres from the surrounding plains to about 1829 metres above sea level. The topography is quite steep, making efficient leach pad construction a major challenge. The climate is semi-arid with moderate summers and occasionally severe winters. Freezing temperatures usually arrive in late October or early November, influencing the effectiveness of leaching operations. GEOLOGY AND MINERALOGY The geology of the Little Rocky Mountains consists of steeply dipping sedimentary ridges forming an elliptical dome surrounding a core of intruding syenite porphyry. Within the syenite porphyry are well fractured and mineralized shear zones where the existing reserves and open pits are located. The ore is presently divided into oxidized, mixed, and sulfide. Only the oxides and mixed zones that are of ore grade are placed on the leach pads. The syenite porphyry host rock enables effective leaching of gold and silver to depths of 61 metres, having a major impact on leach pad construction costs. MINING All mining since 1979 has been by contractor. This enabled initial mining to commence without capital investment in equipment. Through competitive negotiations, Pegasus has been able to keep contract mining costs at levels very close to what would be experienced if Pegasus had purchased equipment initially. Contracts are negotiated yearly and are based on a unit price and haul distance for ore and waste. Haul distances have ranged from as little as 457 metres to as much as 3,050 metres. At present, Pegasus is developing a 27,000,000-tonne leach pad at the Landusky project that is adjacent to the minine area. This design feature will reduce the mining cost by 20 percent over the life of the mine. In 1987, over 5,900,000 tonnes of ore and 3,200,000 tonnes of waste will be mined at the Landusky project. Through 1986, 13,763,000 tonnes of ore have been mined at a waste-to-ore strip ratio of 0.60:l at the Zortman project, and 13,005,000 tonnes of ore at a waste-to-ore strip ratio of 0.79:l have been mined at the Landusky project. Current mining reserves are 32,769,000 tonnes of ore at a waste- to-ore strip ratio of 0.59:l. Through efficiencies of large-scale heap leaching, Pegasus has been able to lower the mining cutoff from 0.34 grams per tonne gold to 0.27 grams per tonne gold. This has reduced the mining cost per tonne of ore h percent through a reduction in strip ratio of 14 percent. Beginning in 1984, all pits were designed based on computer-generated "floating cone" pits. The geologic models were developed by Pegasus staff with a series of economic models evaluated. The resulting computer-generated pits were used as a guideline in designing the mine plans, including haul roads for final calculation of tons and grade. Input to the floating cone models consisted of mining cost, processing cost, cutoff grade (0.34 grams gold per tonne), recovery (67 percent) and gold price. Due to the gold being deposited primarily on the fractures of the syenite host rock, no crushing of ore is needed prior to leaching. This characteristic of the ore is a key in being able to profitably mine and process gold ore at an average grade of 0.69 grams of gold per tonne. Strict blasting control is also a key in success of the leaching operation. A system of splitting ore and waste in blast patterns has been devised to reduce dilution. Also, drill hole spacings are varied from 3m x 3m in breccia ore to 4m x 4m in syenite ore to 5m x 5m in waste. Drill holes

Jan 1, 1987

By Lee A. Goetz

Cost control is a lot like motherhood - everyone proclaims its need and its worthiness, but is it really appreciated and used to successfully complete a project on time and within budget? Good Cost Control is a yardstick - requiring fixed definition but this does not mean rigidity for the project. It provides the means for telling: 1. Where you are going 2. When you will complete and 3. What it will finally cost. Cost Control does not fix the price of dreams nor the cost of projects loosely defined. It does not control costs in itself but provides the tools whereby engineering decisions can be made which will ultimately affect the project cost It does not even guarantee that a project will be completed within the original funds - but only, if this reflects management desires.

Jan 1, 1970

By F. H. Mertens

The concentrators of Gecamines are fed by a great variety of ores and produce different types of oxide and sulfide concentrates. It is therefore important to translate the performances of each circuit in terns of dollars in order to reach cost optimization in each mine to product line. A new system has been recently implemented for achieving this objective. Technical data and expenses are collected, allocated and analysed on mainframe applications. On the other hand, optimization and simulations are carried out on microcomputers which are linked with the mainframe files. Various kinds of auditing reports can be produced, including those leading to investments and cash-flow pattern which are

Jan 1, 1991

By W. Zieman

"The low consumption of reagents can probably be attributed to a good clean type of ore. The cyanide level is kept at 0. 8 lb/ ton of solution and the lime at 1. 8 to 1.9 lb per ton of solution (pH 12. 2 to 12 .3). Experience in cutting down the lime level in half produced troubles in the presses, in the refinery and resulted in higher cyanide consumption. Finally the residue increased under these conditions, High lime always seems to prevent the trouble from occurring.A survey at one mine of the taxable work, performed in the mine shops for use in the mine, showed that under the new regulations, this had increased some 30 times what it was before the new rules came into effect on June 14, 1963.A water softener idea is incorporated at Lamaque with the crude addition of 100 lb of lime per shift to a spare agitator to precipitate the bicarbonates as carbonates from the water before it enters the mill. The lime titration of the softened water is about 0,2 to 0.3 lb per ton of solution (pH 11). This water is used mainly on the filters as washes."

Jan 1, 1964

By F. H. Mertens

The costs of an open-pit operation can be classified according to the following hierarchy : -overall cost of production (per ton of ore) -costs of basic operations and functions -costs of auxiliary operations -costs of machines and equipment -maintenance costs. Production cost is a measure of the open-pit mine performance and should be the final target of the management control. It is also a measure of the share of the mine in the processing stages.

Jan 1, 1990

In order to achieve optimum results for money spent in construction of new projects there is a need for mining developers to pay greater attention to cost control. Control is achieved by establishing a frame of reference, a method of checking and a means of remedial action. The frame of reference is a well coded set of budget estimates which graduate into definitive estimates as design is completed, backed up by drawings, specifications and bills of quantities. The method of checking is provided by cost engineering and quantity surveying input, at both feasibility study and design and documentation stages. Remedial action follows if the checking process reveals a need. In large complex projects where construction completion time is often of prime importance, control of costs can sometimes be relegated to second place. To avoid this it may be necessary to include specialists in cost control in project management teams. Quantity surveyors are trained specifically in construction economics and can provide develop- ers and project engineers with valuable support at all stages of construction.

Jan 1, 1983

By Gary B. Hemphill

Estimators will agree that estimating for excavation is the most difficult costing task. Equipment costs and production rates are the toughest to determine. The following illustration is a method that can be used for this determination.

Jan 1, 1976

By Jose Maria Rodriguez-Ibabe, Ronaldo Antonio Neves Marques Barbosa, Douglas Glenn Stalheim

Major costs in the production of both flat and long commodity grade structural steel products include alloy, labor and energy. Flat and long commodity grade structural steels such as ASTM A36, ASTM A527Gr50, S235, S275, S355 and other equivalent world societal standards represent over 500 million annual tons worldwide. These simple commodity grades consist of a minimum of three base common alloying elements, carbon, manganese, silicon and then can be supplemented with microalloying elements of either vanadium or niobium. Since 2016 raw material costs for two of the five alloying elements in these commodity grade structural steels, FeMn and FeV, have risen significantly and/or have become volatile making it difficult to maintain stability in profitability for these commodity grades. For steel plants producing hundreds of thousands and in some cases over a million tons annually of these common structural steel grades because of the significant alloy cost increase for Mn and V alloy additions has squeezed profitability of these grades. These grades typically represent the base loading for cost controls in most all steel plants and hence a significant cost increase or volatility in two of the five elements used for these grades having a negative effect on overall production costs. However, with a proper strategy for alloy designs working in conjunction with the mills existing processing capabilities to achieve the desired end metallurgy/mechanical properties, alloy costs and operational efficiencies can be realized.

Oct 1, 2019

By Allen H. Gipson

Innovative thinking has led to the development of safe, environmentally sound, and cost effective methods for expanding existing tailings storage facilities (TSF). Three case histories are discussed here to demonstrate methods that have recently been used or are being considered for such expansions. Maintaining the integrity of the structure and reducing costs were primary goals in each case.

Jan 1, 1997

By Gigmai W

Ok Tedi Mine is a high production open pit porphyry copper mine located high in the Star mountains of Papua New Guinea. The mine produces an average of 160 000 tonnes of ore and waste daily at a 1:1 strip ratio. Full scale drilling and blasting began in 1988, prior to which time all material was ripped and dozed.Drilling and blasting procedures at Ok Tedi underwent a major review commencing mid-1989. As a result of a mutual commitment by management at Ok Tedi and the mines explosives supplier ICI, significant reductions in overall blasting costs have been realised. These cost savings are primarily the result of the introduction of air bags, expanded patterns and better field execution.

Jan 1, 1992

By T. W. West

A description of a coal washing spiral is presented, together with a discussion of the parameters which define the envelope within which the spiral can be successfully applied. The correct process engineering, installation, operating and maintenance parameters are addressed as well as actual results for new and retrofit installations on USA coal capital and operating costs of spiral circuits are compared to those of traditional fine coal circuitry.

Jan 1, 1988

By P. M. Tait, N. A. Warner

"The refining of thermally produced zinc is currently performed using a highly energy intensive and arguably outmoded process, distilling zinc under atmospheric pressure at temperatures of 900°C to 1000°C. In order to produce refined zinc more profitably and with less environmental impact a new process has been proposed. This process is generic to all thermal zinc smelters and aims to match the purity of zinc from current technology (99.99%-99.999%). The objective is to perform all separation processes using only the heat contained in the smelter product stream. Vacuum conditions are extensively used lowering operating temperatures and enhancing separations. As part of this process zinc is distilled under vacuum from high concentration obtaining a refined product with respect to lead content. A mathematical model has been developed from fundamental principles to describe this stage, the distillation of zinc across a temperature difference between two circulating zinc streams in open channels under vacuum. Heat for the distillation is supplied by the liquid phase, necessitating a large recycle to maintain high operating temperatures, and keep zinc concentrations high. In determining this model and the operating conditions required, relationships between temperature, pressure and composition are considered.IntroductionCurrent technology (the Refluxer) used to refine thermally produced zinc is both expensive and highly inefficient. At present 80% of the worlds zinc is produced via the electrolytic process reflecting the poorer performance of the thermal route, the zinc-lead blast furnace and Refluxer. A new process is proposed to overcome the drawbacks of current processes. These drawbacks are both economic and environmental. The Refluxer requires 6.6 GJ of energy to refine one tonne of SHG zinc 1, other disadvantages of the Refluxer stem from high operating temperature, around 900°C, and liquid zinc being highly corrosive towards ferrous metals. The Refluxer is constructed from silicon carbide sections which join together by means of flat machined faces making liquid metal leaks inevitable. The Refluxer columns are very sensitive to thermal cycling, thermal shock and mechanical vibration, which easily lead to structural failure. To avoid thermal stress on the columns the feed rate and feed temperature need to be kept constant which means the feed baths to the columns must be able to accept solid and liquid feed as the Refluxer has to operate when the smelter is shut down."

Jan 1, 1998

By G Lane

This paper discusses the factors that contribute to the cost effective design of a concentrator. Concentrator design and layout outcomes are functions of the team (engineer’s and owner’s) participating in each particular project. The benchmark for relatively modest projects was set in the 1980s and 1990s during the ‘gold boom’ when numerous cost effective plants were designed and constructed on a lump sum basis in a very competitive market. A number of factors contribute to lack of transference of the lessons learnt in gold plant design to concentrator design including established paradigms in the design and layout of concentrators, lack of experience in cost effective design, operator’s preferences for flowsheet and layout and simple lack of appreciation of the impact of plant footprint on materials quantities and resultant capital costs.Experiences with recent copper concentrator projects (both small and large) are used as case studies.

Aug 8, 2011