Search Documents

By Rob van Dorp

Most traditional foundation designs are based on soil investigations using Standard Penetration Testing (SPT), sometimes combined with static load testing on sacrificial trial piles. However, this design approach has two major shortcomings. First, SPT data do not provide direct and continuous informa- tion about soil resistance as a function of depth. Second and more important, because of the relatively wide spacing between borehole locations, SPT soil investigations do not provide adequate information about variability of soil profile and/or soil resistance over the project area. Preliminary pile load testing on an SPT location can compen- sate for the first disadvantage but cannot address the second disadvantage. A design approach based on an adequate soil investigation campaign with Cone

May 1, 2022

By D Reid, A Fourie, J Ayala

This paper discusses cone penetration test correlations for loose gold tailings that were developed within a critical state soil mechanics framework. The development of a new calibration chamber for cone penetration testing that consists of a modified triaxial cell is described. Some of the early development and commissioning issues that were encountered, as well as the solutions adopted are outlined, including the system to prepare the samples and to acquire high-quality data from the testing. Also, the triaxial laboratory testing required to achieve the critical state line is described, including some of the basic precautions considered necessary as good practice. Additionally, the system adopted for volume tracking of the calibration chamber sample is described, which is essential for ensuring a reliable state parameter comparison against the acquired cone penetration test data. Finally, some laboratory test data from the calibration chamber is plotted against the soil behaviour type charts currently available from various authors.

Jul 1, 2021

By J. D. Prater, H. R. Spedden, E. E. Malouf

Application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production, whereas formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing so1utions.l Detailed investigations made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a precipitation cone-type recovery system having advantages over older methods.

Jan 4, 1966

By Baltus Cornelius Bonse

Foi desenvolvido um composto de elastômeros termorrígido (ebonite) para a fabricação de um selo mecânico de vedação de hélices de barcos, para substituir os modelos comumente encontrados de cerâmico, que possuem alto custo e são fabricados no exterior, e de borracha com face em Teflon®, que apresentam problemas de adesão na linha de junção entre estes materiais, resultando em vazamentos. O composto de elastômeros deveria possuir dureza em torno de 90 Shore D, baixo coeficiente de atrito, resistência térmica, a abrasão e a intempéries marítimas, ao ataque de radiação UV e ser autolubrificante. A formulação que resultou no melhor produto consistia das borrachas natural, nitrílica, nitrílica carboxilada, e fluorada (Viton®), aditivadas com alto teor de enxofre (37,5 phr), cargas reforçantes, plastificantes e lubrificantes sólidos, entre outros aditivos. A aditivação e mistura das borrachas foram realizadas em misturador interno Banbury e misturador de cilindros aberto, enquanto a conformação e vulcanização dos corpos de prova e dos selos foram realizadas por prensagem a quente. Foram realizadas análises de curva reométrica, morfológicas por microscopia eletrônica de varredura, de resistência à tração, rasgo, dureza e de abrasão em torno mecânico simulando a pressão de vedação em atrito com o aço inox girando a 800 rpm. O êxito do selo ficou evidente, pois após a montagem em barcos, durante um ano tem realizado com sucesso a sua função.

Aug 8, 2018

It?s a pleasure to be with you in Vancouver today to reinforce the good work you and your companies do to develop and operationalize new technology as a lever to improve operational performance and reduce our impact on the environment in absolute terms. Although I will use the work we do at Shell to reinforce this perspective, the principles apply to all of us in this industry regardless of whether you are a producer or supplier. I?d like to help demystify the future of Canada?s oil sands based on Shell?s view of global energy developments, including forecasted demand. One of the incontrovertible truths of this era of global energy defines change as an unchangeable law of progress. Another tells us that the art of progress is to preserve order amid change and to preserve change amid order. These axioms help frame the increasingly public debate about the future of Canada?s oil sands. I hope to illustrate how Shell?s commitment and investments create positive progress that embraces change amid order in the oil sands. I?m going to spend a little time today to focus the spotlight on the future of the oil sands to help demystify Canada?s hydrocarbon energy future. To do that, I?ll identify the features of our future energy security, including three hard truths about global energy that drive Shell?s business imperatives. Then, it?s instructive to examine Canadians? current consciousness about oil sands sustainability.

Oct 1, 2009

Africa is rich in natural resources, much of which remain untapped. Despite that, international mining companies have largely stayed away from the continent due to political instability in many countries, lack of infrastructure and the inability to gain control of mineral deposits. Today, optimism is growing concerning African mining. Many of its nations are moving toward privatization of their mining industries. They see it as a way to improve the lives of their populations and become politically stronger. Ministers from 22 African nations were Denver, CO in June for the World Bank's Multilateral Investment Guarantee Agency's Fourth Annual African Mining Investment Symposium. The three-day symposium drew more than 400 mining executives and government representatives. Foreign mining investment in Africa is on the increase. In 1996, international mining companies spent about $418 million on exploration. That is more than double the $190 million spent in 1994. Mining executives say the mining climate in Africa is improving because countries are privatizing the industry and rewriting mining laws that encourage natural resource development. They estimate that private mining firms now control about 80% of mining today. Mine development will help lift the living standards for Africans, the ministers said. The average income for ordinary Africans is about $500 a year. If this new mining boom continues, citizens of nearly all African nations will reap the benefits of better infrastructure and government services, as well as more higher paying jobs, the ministers said. They also issued a word of caution to mining companies attempting to join in the African boom. Concerns are being raised about the treatment of villagers and the environment. In the past, foreign companies would "behave about like colonial masters," said Gerald Ssendaula, natural resource minister for Uganda. Africa is in a different position now, he said. "Now we are solving our own problems." Mining companies must respect local communities or risk creating unrest that will threaten fragile new governments, said Akolang Tombale, chief geologist for Botswana. On the other hand, he said villagers must accept that mining development will benefit them. "They feel these are their natural resources. There must be a mutual interaction between the companies and the people."

Jan 1, 1997

Following the suggestion of Engineering Council and at the direction of, the President, representatives from each of the Federal Government bureaus interested in map-making were called into a conference for the purpose of coordinating all of the Government's map-making activities. This conference has now reported back to the President the results of its findings, which indicate that Engineering Council's recommendation in this matter was well founded. While the conference report states that its members were of the opinion that little duplication of effort existed, it recommends the formation of a permanent Board of Surveys and Maps. An extended review of the map-making activities, which is given as an appendix to the report, indicates that this recommendation is a logical step. The conference recommendations concerning this Board of Surveys and Maps are as follows: (1) the Board is to he com-posed of representatives of mapping bureaus to be assisted by outside engineering organizations, which have been named above; (2) the estab-lishment of an information office in one of the Government bureaus, preferably the Geological Survey, which is to be under the supervision of the Board and is to be a mapping information clearing house for the Government and outside engineering organizations; (3) copyright laws are to be so changed that copies of all. maps made in the United States and with Governmental authority, will go to the central information office; (4) the Government departments are to receive orders to cooperate, with the Board; (5) future topographic maps of all kinds are to conform with specifications for the standard topographic map; (6) the U. S. Coast and Geodetic Survey to have supervision of final adjustment of all important control data under specifications approved by Board of Surveys and Maps; (7) surveys in the form of maps and publications are to be issued as soon as possible after field work has been completed; (8) program of the Interdepartmental Committee on Aerial Surveying was approved. Outside technical and scientific organizations that are called in for consultation are to operate in an advisory capacity only, responsibility for action on Governmental work is. to rest solely with the Governmental agencies.

Jan 12, 1919

Seventy-one delegates, representing 74 organizations with a membership in excess of 105,000, attended a conference of technical societies, in Chicago, Apr. 23-25. It was called by Engineering Council, and unanimously adopted a resolution urging Congress to establish a Department of Public Works. This would include the services and bureaus having to do chiefly, with matters of engineering and architecture. Among the bureaus, services, and activities, which logically belong to a Department of Public Works, are the following: Bureau of Public Roads; the United States Reclamation Service; the Alaskan Engineering Commission; the Construction Division of U. S. Army; a Bureau of River, Harbor and Canal work, including such functions as are now exercised by the Mississippi River Commission and the California Debris Commission; a Bureau of Architecture; a Bureau of Surveys, including the Coast and Geodetic Survey; a Bureau of Mines; the Geological Survey; the Forest Service, at least until the same is divorced from the supervision of water powers and road building; and the Bureau of Standards. Later, the following resolutions were unanimously adopted: RESOLVED, That this conference be known as the Engineers, Architects, and Constructors Conference on National Public Works; that it continue in existence until dissolved by its own action and that its officers and committees be empowered to further the organization and development of a National Department of Public Works. RESOLVED, That for the purpose of furthering the passage of a bill for the creation of a National Department of Public Works there be set tip by this Conference an Executive Committee, a Committee on Text of Bill, and a Campaign Committee. The Executive Committee shall have the power to create a Finance Committee and other committees and to add to its own membership or to that of its committees.

Jan 6, 1919

By W. R. Toeplitz

Probably a more descriptive title would be "Much Ado About Nothing." By "nothing," of course, I refer to the porosity which is the main feature of this type of bearing. Porosity has a decided effect on the manufacturing techniques, the structure and physical properties, the oil content, and on the installation and service of oil-retaining porous bronze bearings. A simple curve can be drawn by plotting specific gravity along the abscissa and percentage of porosity by volume on the ordinate. A bronze composition, analyzing 89 Per cent copper, 9.75 Per cent tin, and 1.25 per cent graphite, has an absolute solid specific gravity of 8.5. At this specific gravity, of course, occurs the point of zero porosity. Conversely, at loo per cent porosity, the specific gravity is zero. A similar curve can be drawn for bearings impregnated with oil; the only change being that the specific gravity at loo per cent oil will be 0.89 if we assume that that is the specific gravity of the lubricant. The curve is useful in determining the oil content by volume for any specific gravity. The normal range of oil content for porous bronze bearings of this composition is from 35 to 16 per cent, which is in the specific gravity range of from 5.8 to 7.3. In addition to the amount of porosity, the type of porosity is important. The first consideration here is that the porosity must be intercommunicating. This can be determined by a number of simple tests. The first method, which is very accurate, is to extract the oil in the bearing by cycling

Jan 1, 1945

By W. R. Toeplitz

H. N. Ghenn.*—It has been established that the accuracy obtainable from any precision machine is a function of the wear resistance, maintenance and closeness of fit of the bearings, hence I would like to ask Mr. Toeplitz how these oil-less bearings compare with cast iron or babbitt or similar materials when used on precision machinery. Could these bearings be used, for example, on a grinding machine in which work must be held to a tolerance of plus or minus 0.000025 inch? W. R. TOEPLITZ.—The metal-powder bearings can be held to very close tolerances and are used in place of cast iron and babbitt on precision machinery.

Jan 1, 1945

By R. R. Hoffman

The name L'brush,l as applied to the parts to be briefly considered in this paper, is not clearly descriptive of the design and function of those parts when the usual definition of the word is applied. In a general way, the brushes to be considered here are the parts employed on certain types of electrical equipment to facilitate the transfer of electrical current between a rotating or moving element and a stationary element. These machines are generally motors and generators of both the slip-ring and commutator types, rotary converters, battery charges, etc. Parts that serve a similar purpose on relatively slow or intermittently moving devices such as rheostats, switches, controllers, etc., are generally referred to as contacts. A few special applications involve the use of current-carrying washers, rollers, bushings, etc. As may be inferred, therefore, the design of these brushes and allied parts is dictated by both electrical and mechanical considerations. In most cases these factors are closely interrelated, and unfortunately many of them are not subject to exact scientific or mathematical analysis. Special Advantages Since brushes operating on direct-current machines must carry the load current, resist destructive action from voltage induced in imperfectly compensated armature coils, and in addition act as a bearing material, maintaining intimate contact with the commutator at peripheral speed, which may be as high as 70 miles per hour it is difficult to obtain in one brush the ideal properties necessary for perfect functioning under all operating conditions. The engineer-designer, therefore, when selecting a brush for a specific application, must choose a grade that possesses the characteristics most adequate to meet the conditions involved. In many cases a characteristic that makes a specific grade of brush the ideal selection for one type of machine may be of secondary importance to some other property when the brush is applied on another machine. Frequently different grades of brushes must be applied to the same type of machines when they operate under different or unusual atmospheric conditions. Completely satisfactory brush operation depends on freedom from appreciable sparking, minimum electrical and mechanical losses, negligible commutator or slip-ring wear, uniform film over the commutator or slip ring, quiet operation and good brush life. The ability to produce special structures, and to combine in widely varying proportions materials that are incompatible, through conventional melting and alloying procedures has been the basic contribution of powder metallurgy to the solution of problems involving brushes and allied parts. This is especially true where current-carrying capacity is a major factor, owing to the limitations of all carbon or all graphite brushes in that respect. Metal-graphite Brushes With very few exceptions, friction between moving elements. across which

Jan 1, 1945

By F. R. Hensel

The present paper describes a number of experiments with fine silver, coin silver, silver-cadmium oxide and silver-nickei-copper compacts, prepared by powder metallurgical methods. The test data are of a preliminary nature, since most of the work was exploratory. Fine Silver Eject of Compacting Pressure on Hardness and Density during Cold and Hot Pressing The cold-welding properties of silver have received considerable attention and the welding characteristics are functions of such variables as: cleanliness of metal particles (impurities and adsorbed gases), chemical nobility of particles, plasticity and hardness, particle assortment, particle shape, particle porosity, apparent density, temperature, pressure, time, recrystalliza-tion characteristics. Chemical nobility, plasticity and low temperature of recrystallization after work-hardening are responsible for the excellent low-temperature bonding properties of silver. Several series of compacts were pressed at pressures of 5, 10, 20, 30, 40, 50, 60 70 and 80 tons per square inch, at temperatures of 32°C. (room temperature), l00°, 2000, 300°, 400°, and 450°C. Silver powder of minus 325-mesh, produced by displacing silver from a nitrate solution by means of copper, was used. The density was calcuiated from accurately measured and weighed compacts. The hardness was measured on the Rockwell F scale. The investigation shows that an increase in pressure promotes a higher density and hardness regardless of pressing temperature, up to a temperature of 400° C. The pressure-density curves at various pressing temperatures are shown in Fig. I, the pressure-hardness curves at various pressing temperatures, in Fig. z. The greatest increase in both hardness and density was obtained in the pressure range of 5 to 20 tons per square inch. A compact from each series was annealed at 300°C. in air, for various lengths of time. The hardness values after annealing are shown in Table I. A minimum hardness was obtained after one hour of annealing. No change in density occurred during annealing. The maximum density was obtained at 80 tons per sq. in., and at this pressure the hardness is equal to that of hard-drawn wrought

Jan 1, 1945

By F. R. Hensel

P. R. Kalischer.*—I should like to amplify a little one of the points made by Dr. Hensel, and rather violently disagree with him at the same time. He brought out the point that when the higher forming pressures are used on the green compacts there is a marked decrease in the density as sintered. We found that to be true and, of course, many of you notice that that is true with copper compacts also. But, in my opinion at least, it is not true that the expansion is due to entrapped air. We have vacuum-pressed both silver and copper compacts and obtained almost exactly the same numerical expansion as we secured by pressing in air. The powder, however, that is vacuum-annealed does show a slight decrease in expansion on sintering, but almost the entire increase on expansion can be overcome by very slow rates of heating. And it is our opinion that a majority of the expansion is due to dissolved oxygen in the discrete metal particles themselves rather than to entrapped gases. Another interesting observation that we have made is that often with silver or copper compacts it is desirable to silver solder or braze the compact into some part of a piece of equipment after completing powder metallurgical operations on it. If such a compact is sintered and coined, say a silver compact, given an initial forming pressure of 10 to 15 tons per square inch, and sintered, there is an adequate amount of shrinkage and it can be coined at about 50 or 60 tons per square inch and bring up the density nearly to theoretical. If, then, that compact is silver-soldered into some part of a fixture or a machine, it will expand very beautifully, and the only way that this can be overcome. as far as we know, has been to reanneal after the coining operation at a temperature higher than is to be used in any subsequent operation. In that way, a density very nearly theoretical can be achieved, but the coining operation cannot be carried to the excessively high pressures or expansion and bubbling of the compact will occur again.

Jan 1, 1945

By F. H. Rhines

Page Foreword. By F. N. Rhines............................525 Design Factors for the Metal Forms with Which Powder Metallurgy May Compete. By Fred P. Peters...................... ......527 Discussion..................................530 Powder Metallargy as Applied to Machine Parts. By A. J. LanghamMer........531 Discussion......................... . Pole Pieces for Electric Motors from Iron Powder. By F. V. Lenel...........535 Discussion....................... . Bearings from Metal Powders. By W. R. Toeplitz.................542 Discussion.........................'.........549 Brushes and Allied Powder-metal Parts. By R. R. Hoffman . .............'550 Electrical Contacts Manufactured from Metal Powders. By E. I. Larsen........554 Sintered Magnets. By C. B. Fulton........................557 Friction Articles from Metal Powders. By C. T. Cox..................565 Discussion..................................567 Certain Characteristics of Silver-base Powder Metallurgical Products. By I?. R. Hensel and E. I. Larsen........................ ....569 Discussion............................... . . . . 579 Some Properties of Sintered and Hot-pressed Copper-tin Powder Compacts. By C. G. Goetzel..................................580 Discussion..................................593 The Sintering of Metal Powders—Copper. By C. J. Bier and J. F. O'Keefe......596 Some Experiments on the Effect of Pressure on Metal-powder Compacts. By Jerome F. Kuzmick..................................612 Discussion.................................. 630

Jan 1, 1945

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy's future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By Fred P. Peters

T. D. Yensen.*—As my information is of a negative nature, I think it belongs under this paper. We are particularly interested in magnetic materials and we would like very much on occasions to make use of powder metallurgy. We have tried repeatedly to use powder metallurgy in preparing our nickel alloys but always. with negative results; that is, we cannot get as good magnetic properties by powder metallurgy as we can by starting with a molten material. We have tried by all possible means to make materials' like 50 per cent iron-nickel alloys by powder metallurgy. The compacts can be regularly lorged and rolled but no matter what we do in the way of annealing, the magnetic properties come out very much poorer than if we start with molten material. F. V. Lenel. †—I want to mention one characteristic of articles made from metal powders which distinguishes them from die castings; that is, their wear resistance. Die castings usually are made from zinc or aluminum alloys and a few copper-zinc alloys; all of them are comparatively soft and not very wear resistant. I know of a number of cases where powder metallurgy rather than the die-casting method was used for producing a certain part because higher wear resistance was needed than could be attained in die castings. A, J. LanghammeR.*—The subject of powder metallurgy is somewhat difficult to discuss, and portray, in the time that his been allotted. Most of you would rightly be bored if we went into details. However, I will cite one incident that possibly will help illustrate some of the potentials. Last summer I was in Washington and met Navy officials for the purpose of studying the possibility of making a certain part by powder metallurgy. The part is highly intricate and I happened to remark that the material cost would be high; that is, the cost on one raw material. Promptly a high-ranking Navy officer said: "Mr. Langhammer, if you must pay x dollars a pound for the raw material, but achieve the desired results, the cost of the finished part would still be low."

Jan 1, 1945

By E. I. Larsen

Powder metallurgy has been described as being "as old as the pyramids and yet as new as the latest bomber." While this may be true literally, it has been only in the last Io or 1 5 years that widespread use has been made of this method of fabricating various articles One of the first items fabricated by powder metallurgical methods on a commercial scale was electrical contacts, which were fabricated from metal powders as early as 1920. The reason why these contacts have been made for so many years by powder metallurgy is because the compositions of most of these materials arc such that they could not be made by the conventional methods of melting, casting, rolling, drawing, etc. Classes of Contacts In general, electrical contacts fabricated from metal powders fall into two classes, both from the point of view of the method of fabrication and the components that make up the chemical composition. One class is composed of silver or copper and a refractory metal such as tungsten, molybdenum, or compounds thereof such as carbides. The second class contains a predominant amount of silver and a semi-refractory material such as cadmium oxide, nickel, cobalt, or graphite. Electrical contacts of the first class have been developed primarily as facing materials for heavy-duty circuit-interrupting devices. This class of material unites the high melting point, high boiling point, great resistance to electrical erosion, and the refractory characteristics of molybdenum, tungsten, or their carbides with the high thermal and electrical conductivities and low contact resistance properties of silver or copper. The second class of material is used for lighter duty or specialized applications such as heavy-duty, direct-current aircraft relays. Varieties Electrical contacts fabricated from metal powders are made in a wide variety of compositions, shapes, and sizes. In general, the sizes of electrical contacts fabricated from powders vary from contacts weighing approximately 0.001 oz. up to those weighing 3 to 4 Ib., the contacting face being as small as 0.001 sq. in. up to approximately 6 sq. in. in area. The shapes consist of: sound or rectangular buttons, some of which have radii or bevels on the contacting faces; rings, cups, rectangular bars, the contact face of which may have a radius across the width and/or at one end; and form-pressed pieces of a wide variety such as angles, both acute and obtuse, irregular shapes comprising a radius blended into a flat, which in turn may have steps. The size or shape of the contact is dictated principally by the mechanical design of the manufacturer, who in turn may have problems to be met such as: (I) size, weight, or space limitations; (2) electrical conditions such as blowout coils arc chutes, baffies, gas passages.

Jan 1, 1945

By C. T. Cox

The title of this short paper necessarily implies that friction articles comprise a distinct and unique field and are different from the other metal-powder articles, such as bearings, electrical contacts, and magnets. However, this distinction is rather hard to define in that it is really one of degree and not Of kind. It would appear that the main distinction is that friction are are articles of rather large pressing area. In other words, they are articles in which the area Of the mold in which the metal powder is pressed is relatively large. Other articles made from meta1 powders are generally of rather small area, usually a few square inches, while in friction articles the area ranges up to several hundred square inches. The satisfactory production of meta1-powder friction articles involves many production problems and a large number Of these are accentuated by the large area' Since it is impossible in the short space of this Paper to describe adequately all the problems involved, I have thought it best to merely mention some Of them and to place particular emphasis upon a problem that is common to all metal-powder articles, although it is of greater importance in the making of friction articles. This problem has to do with the effect On the properties of a friction article of small variations in the composition. However, before discussing the problems, it is probably appropriate that some mention be made of the limitations on the use of friction articles. Most engineers are familiar with the general field that can be characterized as constituted by clutch facings and brake linings, and undoubtedly have heard many stories of how metal-powder friction articles have had a service life 10 times as long as nonmetallic friction materials, and of instances where metal-powder friction articles have operated satisfactorily where no other material could be used. These instances should not be regarded as criteria for the assumption that metal-powder friction articles are capable of universal use in the friction field and will always outperform other materials. On the contrary, metal-powder friction articles are unsuitable for numerous applications, either on a performance or on a cost basis. Metal-powder friction articles will not replace wooden block brakes for wagon wheels nor cast-iron brake shoes for railway car wheels, to mention just two obvious examples. Metallic friction articles cannot be used where they must act as heat insulatorsl for they have a relatively high thermal conductivity as compared with asbestos. This is a detriment in some uses, as in certain airplane brakes having hydraulic actuators provided with rubber seals. The metallic friction material readily transfers the heat developed at the braking surface back through the material to the rubber seal and destroys it. Within its limited field, metal-powder friction material has proved satisfactory, but many problems are involved in the Selection of the proper material to use in an application and in the commercial pro-

Jan 1, 1945

By C. T. Cox

W. A. Reich.*—I should like to ask Mr. Cox if he has any information on the change in

Jan 1, 1945

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945