Search Documents

By H. A. Schwartz

FROM time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion1 of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composition: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213° to 1132° C., the latter figure agreeing with Gontermann's data .2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the metastable diagram, from a temperature somewhat below the eutectic freezing point to a temperature below Ar1 and for a graphitic-carbon content from practically nothing to the original total carbon of the specimen (see Fig. 6). More especially we desired to locate the line in the stable diagram corresponding to the Acm line of the metastable system, which is designated by analogy, the Atm line (tm from temper carbon) ; also to determine the location of Aim with respect to Acm toward their lower extremities at Ar1 in order to determine whether or not graphitization is completed by the separation of an iron-carbon eutectoid analagous to pearlite in the iron-cementite system. This would involve further a comparison of the locations of the stable and metastable A1 points.

Jan 8, 1922

By I. O. Flores, A. Anani, H. Li

Current technological advancement has increased the exploitation of deeper ore bodies using underground methods. In certain cases, the mineral deposit starts near the surface and continues deep within the earth's crust. Such deposits are best mined with both underground and surface methods. Two main techniques are used to determine the optimal transition depth from surface to underground - a disintegrated approach and an integrated approach. Both methods have limitations in their use to determine the optimal transition depth. The objective of this research is to investigate the conditions in which an integrated approach to the transition depth problem is superior to a disintegrated approach. Three binary integer linear programming models are developed for this purpose: a surface and underground model for the disintegrated instance and an integrated model. A case study is performed to validate the models, with a comparative sensitivity analysis to obtain operational insights.

Sep 1, 2021

By Mark A. Krall, Robert L. Geddes, James C. Frost

Introduction The Conda Partnership's Dry Valley phosphate mine is a thinly bedded, multiple seam open-pit mining operation where selective mining techniques are used to recover phosphatic shales. The mining methods used are truck/shovel and scraper/dozer operations. Ore is shipped 32 km (20 miles) by rail to a beneficiation facility. The ore is upgraded by washing and calcining. The mine and beneficiation complexes are owned by the Conda partnership. It is a joint venture between Beker Industries Corp., of Greenwich, CT, and Western Co-Operative Fertilizers (US) Inc., of Alberta, Canada. The Partnership operates as a separate entity of the two partners. The Dry Valley mine is located 48 km (30 miles) northeast of Soda Springs in Caribou County in southeastern Idaho. The mine is situated on the Caribou National Forest. Mining operations take place between 2 and 2.4 km (6400 and 7900 ft) in elevation. It is accessible partly by 32 km (20 miles) of paved roads and 16 km (10 miles) of dirt roads. The winters are long and severe, and the summers are short and mild. This article describes the history, geology, exploration, mining, and reclamation that makes this mine Idaho's largest producing mine and the western US' leading phosphate producer. History and production In the mid-1950s, Western Fertilizers of Salt Lake City, UT, drove an exploratory drift in Maybe Canyon. A large bulk sample of phosphatic shales was analyzed for phosphate content and processing characteristics. No large scale mining or processing operations were undertaken. In the late 1950s, the Dry Valley property was sold to Central Farmers of Chicago, IL. No major operations took place. In 1964, Central Farmers sold the property to El Paso Products Co. of Odessa, TX. El Paso Products supervised the mining operations of Wells Cargo Mining Co. from 1965 through 1967. During this time, El Paso Products built a beneficiation facility and a fertilizer complex in Conda. A 32-km (20-mile) railroad was also constructed from the mine to this facility. From 1968 through 1972, the mine was shut down due to a depressed fertilizer market. In 1972, El Paso products sold its ore reserves, beneficiation plant, and fertilizer complex to Beker Industries Corp. In 1979, Beker Industries sold 50% of its ore reserves and 50% of its beneficiation plant to Western Co-Operative Fertilizers (US) Inc., of Alberta Canada, forming the Conda Partnership. It has operated the mine and beneficiation plant since January 1979. From the mid-1950s to the mid-1960s, no substantial production took place. From 1965 to 1967, El Paso Products stripped 3 Mm3 (4 million cu yd) and mined 2.3 Mt (2.5 million st). From 1972 through 1983, 50 Mm3 (66 million cu yd) were stripped and 18 Mt (20 mil¬lion st) were mined. Geology The Wells Formation forms high ridges and hillsides in the Dry Valley area. It is best exposed along the west face of Dry Ridge. It forms the imposing wall on the east side of Dry Valley. The formation is divided into two members. The lower member, about 213 m (700 ft) thick, is dominantly thin to medium-bedded limestone and silty limestone. It contains nodules and stringers of chert and minor sandstone. The upper member is composed principally of thick-bedded to massive cross-bedded, light-gray to orange-yellow, fine grained sandstone. There is some interbedded brown to light-gray limestone. This member varies from 369 to 457 m (1300 to 1500 ft). Recent investigations indicate that the upper Wells is of Permian age. Under some conditions, the Wells may be water-bearing. Otherwise, it has no apparent economic significance. Grandeur Member (Park City Formation) Overlying the Wells Formation is a distinctive light-gray to white dolomitic fossiliferous limestone. This unit has been identified by the US Geological Survey (USGS) as the Grandeur Tongue Member of the Park City Formation. This member is sometimes absent due to its contact with the Meade Peak Member of the Phosphoria Formation. It is easily detectable by its color, hardness, and fetid odor. Phosphoria Formation The Phosphoria Formation of Permian age was named from Phosphoria Gulch, Bear Lake County. The formation has been studied extensively and developed for its economically valuable phosphate reserves.

Jan 11, 1985

By Glen A. Knox

The writer has been asked to set forth for this Institute, the experience of the past eleven months in the mining operation conducted at Sweetwater Mine in which coal has been produced by the use of Link-Belt Conveyors on long faces. The coal in this mine has an average of six feet three inches in thickness, and lies on an average pitch of five degrees. The roof is a sandy shale of medium hardness and has been generally considered as good top in the room and pillar method of mining. When our company became interested in conveyors, the writer visited most all of the mines in the East where conveyors and other mechanical methods of mining were in use and decided that the modified method of w-hat is in use at the Norton-West Virginia mine would be the most feasible for our conditions. We in- stalled three hundred feet of conveyor as an experiment to see whether or not our roof could be handled and taken care of on long faces. This three hundred feet was installed as two separate conveyors, one as a face conveyor-100 feet in length, the other as a heading conveyor that delivered the coal into the mine car on the main entry. This face was worked directly on .the strike and down the pitch. This did not prove to be a success as the caving of the roof carried over to the working face and necessitated propping between the conveyor and the face and it was also necessary to shovel coal on the conveyor up the pitch. After working out this block, 200 feet in length, we installed these two conveyors at a place adjoining this worked out block, but on a half V shape shown on the sketch. This block of coal was sixty feet wide. This method proved to be very successful. We cut a place, moved the conveyor against the face before shooting and carried two rows of cribs between the conveyor and the cave, and caved the roof every second cut. After working out this block we were satisfied that this system was feasible with our mine. We then ordered twelve hundred feet more of the same type as the trial conveyor with the exception of a very few modifications. We then installed this fifteen hundred foot unit on the four faces shown on the sketch, with one hundred feet to each face, two hundred feet on each heading and three hundred feet on the main conveyor that delivered the coal into the pit cars. We also had a head and rear section for each of the four advancing places shown on the sketch. As the sections were taken out of the heading conveyors they were installed on the advancing conveyors, and when the faces approached the main conveyor, the main conveyor was taken out and installed in the next uphill or main conveyor place. The roof caved very well in line of the points and was broken about every twenty feet. It broke in a straight line and did not curve at each V. We encountered no trouble unless we permitted one of the points to get behind. The maximum tonnage possible to be produced on this method was estimated to be seven hundred and twenty-five tons a day, assuming that all places were cut and cleaned up in one shift, and this we did for several consecutive days. While this was a success from a cost standpoint, we felt that we could

Jan 1, 1925

By Oliver C. Ralston, Foster Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of l/z to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles.

Jan 10, 1950

Federal Regulations require that coal producers conduct a written, in-house investigation with every lost time injury accident. Besides their obvious value in accident prevention, competently conducted investigations can provide a number of additional benefits to include positive supervisor involvement, the control of rising worker's compensation costs and a measure of protection from civil/criminal proceedings. The paper describes such topics as MSHA minimum requirements, investigator selection and training, accident site procedures, witness interview techniques and the management review process. The reader is also presented with a number of information resources available through MSHA, the National Safety Council and other sources.

Jan 1, 1995

By P Holtham, K Duffy, B, W Valery, E Tabosa, rade

Pre-concentration has potential to significantly improve Mineral Resource efficiency by removing gangue early in the process, before energy intensive and expensive comminution and fine processing. However, there are numerous options for pre-concentration and the performance and benefits of these are very case specific. To determine the best option for a particular deposit and to successfully integrate it into the overall mining and processing operations requires comprehensive evaluation. This needs to consider orebody suitability, technology capability and economic viability. The in-situ variability of a deposit and how it is influenced by mining methods and the liberation size of gangue are key factors which are generally not well understood. Geostatistical methods provide an insight into orebody variability, and the overall selection of any pre-concentration solution must be an integrated approach between geology, mining and processing. Many pre-concentration evaluations investigate the potential of just one option. Technology selection should start wide and may include: selective mining, pre-screening (with or without selective blasting), sorting (bulk and or particle), coarse gravity separation (e.g. jigging, DMS), coarse particle flotation, magnetic separation, etc. The upgrade performance of these processes is very ore specific and should be determined from testing, with detailed multi-component modelling used to determine the overall process performance. Many of these pre-concentration processes require significant ancillary equipment, feed preparation and materials handling. It is important to realistically estimate all costs to understand overall economics and select the best option. Some examples showing evaluation and comparison of pre-concentration options are presented in this paper. These include assessments of in-situ variability using geostatistical tools, process modelling of pre-concentration options and overall performance, preliminary layouts and cost estimates, and economic evaluations.

Nov 10, 2020

By C J. Greet, J Kinal, C Hitchen

Following the successful completion of a marked ball test defining the potential wear benefits the high chrome alloys may offer against forged steel, as well as laboratory test work investigating changes in pulp chemistry and improvements to metallurgical performance, a plant trial was commissioned at NewcrestÆs Ridgeway concentrator. The paper briefly describes these results.Newcrest decided to convert their media charge by the top-up method. To monitor the trial a sampling protocol was put in place whereby the pulp chemistry was monitored before, during and after the purge. The metallurgical shift data was analysed using various statistical methods to determine if the metallurgical performance had improved with the change in grinding media. While the analysis indicated that the metallurgy had improved, not all of the benefits could be assigned to the change in grinding media alone. However, the combination of reduction in media wear and the increases in copper and gold recoveries suggested that it was economically viable to operate with high chrome grinding media.As with many trials of this nature the prevailing economic conditions are fluid and a decision was made to revert back to forged steel grinding media in an effort to reduce operating costs. It was further agreed that Magotteaux could monitor the pulp chemistry and metallurgical changes in this reverse trial to confirm the results observed in the earlier conversion to high chrome grinding media.CITATION:Greet, C J, Hitchen, C and Kinal, J, 2012. Conducting high chrome grinding media trials at NewcrestÆs Ridgeway Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 56-64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Milton E. Wadsworth

The evolution of engineering education and research has been profoundly influenced by computer technology and has concomitantly followed changes in this technology. Today, virtually all faculty have access to at least two hierarchies of computers: desk personal computers and at least one echelon higher (workstations or a variety of mid-sized computers). Most faculty have access to three or even four hierarchies: the two listed, plus super-mini and super computers. The ready availability of computers at a low cost has increased dedicated and site-specific computer technology. This has permitted universities to move into the field of macro-engineering, to address increasingly complex problems in resource recovery, manufacturing and many other areas, including important societal problems, like the environment. The creation of university research centers indicates the growing importance of macro-engineering involving large systems of interactive components. Funding agencies have increasingly favored such centers since they cross disciplines, generate inter-university consortia and foster university-industry programs.

Jan 1, 1992

By George M. Leonard

Mineral commodities on National Forest System lands contribute to the nation's well being. Access to these commodities is dependent on public perceptions of the effects of mineral operations on other resources. An outlook is described which the Forest Service believes is essential to the minerals industry if it plans to continue seeking minerals on National Forest and Grasslands.

Jan 1, 1991

By V. L. Ketellapper

This paper discusses the technical issues and stakeholder collaborative processes which resulted in achieving a balance between the reclamation of abandoned mine sites, providing affordable housing, and preservation of open space at the French Gulch Site. Through this process, it was discovered that mine site reclamation would need to be conducted in conjunction with two priorities for community sustainable development: providing affordable housing for locals who work in the resort town of Breckenridge, and open space preservation. It was found that conducting these activities concurrently would result in providing resources necessary to complete mine site reclamation. The first phase of the affordable housing development is almost completed. This development resulted in redevelopment of mining impacted lands and was recognized by the U.S. Environmental Protection Agency (EPA) with a National Smart Growth Award in 2002.Negotiations are also underway to preserve the remaining 1,800 acres of land held by the mining company as open space. This transaction will in turn provide resources to address water quality issues associated with mine discharges.

Jan 1, 2004

By N. Ono, H. Fujiwara, S. Otsuka-Yao-Matsuo, T. Omata

"The electrical conductivity and the oxygen release and uptake of sintered indium tin oxide (ITO) upon heating and cooling under the condition that P(O2)/P*=4.9X10-4 (P* = atmospheric pressure), :when P(O2) was approximately 50Pa, were simultaneously measured by using a closed-system oxygen-gas analyzer. A large increasing in -the electrical conductivity - upon the· oxygen release detected in 1130<T<1273K was observed. Quantitative relationship between the number of oxygen atom released from ITO and the conduction electron density in ITO was studied. The release of one oxygen atom agreed with the generation of two conduction electrons, i.e., the efficiency-carrier-generation for the oxygen release from the ITO was almost one. The oxygen atom released must be originally at the quasi-anion site in the C-type rare-earth lattice, i.e., the 16c site in the space group of Ia3, as an interstitial excess oxygen, Oi"". It was concluded that the mechanism of conduction carrier generation and compensation upon SnO2 doping into In2O3 can be expressed by the defect equation, 2SnO2-2Sn1n +2(1-z)e'+zOi""+3O0 x+(l-z)/2O2, and that the oxygen release bringing the increase in the electrical · conductivity can be expressed by the equation, Oi""-1/2O2+2e'.IntroductionThin films of SnO2-doped In2O 3 (generally designated as ITO, for indium tin oxide), which have high optical transparency for visible light and high electrical conductivity, have been used as transparent electrodes for liquid crystal and electrochromic displays. It is well known that the electrical conductivity of ITO depends on the content of SnOi-dopant and oxygen. However, a reliable relationship between electrical conductivity and the absolute oxygen content in ITO has yet to be reported. The elucidation of such a relationship is one of the important clues for realizing extremely highly conductive ITO electrodes."

Jan 1, 2000

By K. S. Raja, F. Battick, B. Pesic

"CeO2 doped with lower valence cations, such as Y3+, Sm3+, Gd3+ etc. is considered as electrolyte material for low temperature SOFC. Doping introduces additional oxygen vacancies and improves ionic conductivity. This work describes the preparation of yttria-calcia doped-ceria precursor material, its sintering in DC and AC field methods, and characterization of sintered electrolytes with respect to the ionic conductivity. Doped precursor materials were prepared by a controlled co-precipitation process. Sintering of prepared, pelletized particulates was carried out using three different methods such as: 1) conventional; 2) spark plasma sintering; and 3) an alternating current field at 1125°C (AC assisted sintering). The mechanism involved in the conductivity improvement as a function of defect density, grain boundary area and phase stability will be discussed. INTRODUCTIONThe performance of SOFCs depends highly on the properties of materials. Subtle variations in the composition, microstructure, or density of SOFC components can considerably alter the power output capabilities of fuel cells. Early SOFCs utilized zirconia based electrolytes but efforts in lowering the operating temperatures of SOFCs have prompted investigations into several other oxygen ion conductors – often modified with dopants to either promote the formation of oxygen vacancies or to stabilize a vacancy rich high temperature phase – such as bismuth oxide, lanthanum gallate, and ceria.The transport of oxygen ions through the electrolyte first begins with diffusion into the material. While this is generally a surface kinetics phenomenon, it is safe to say that it is highly dependent on oxygen pressure and vacancy gradients. The role of the cathode in SOFCs is to reduce oxygen at the electrolyte surface creating an O2– ion gradient which induces permeation into the material. Once inside and under the influence of a potential field, O2– ions migrate by a vacancy hopping mechanism, Catlow, C.R.A. (1990), effectively exchanging positions throughout the matrix until they reach the anode and react, thus leaving the matrix."

Jan 1, 2012

By Susumu Imashuku

A pseudoternary phase diagram of the BaO?ZrO2?ScO1.5 system is established and the conductivities of the scandium-doped barium zirconate are measured in wet conditions. According to the phase diagram, the molar fraction of scandia in the barium zirconate phase that equilibrates with the cubic zirconia (ZrO2) and scandia (Sc2O3) phase is 0.03. On the composition line, where the molar fraction of barium oxide (BaO) is 0.50, the solubility of scandia into barium zirconate is 0.27 as a molar fraction of scandia. At around 500 °C, the conductivities of scandium-doped barium zirconate are estimated to be almost same as that of yttrium-doped barium zirconateThe activation energies for bulk proton conduction in scandium-doped barium zirconate (0.57 eV for BaZr0.90Sc0.10O3-d) are higher than that of yttrium-doped barium zirconate (0.44 eV for BaZr0.90Y0.10O3-d). In addition, the bulk conductivity of scandium-doped barium zirconate in this study is 10 times higher than the reported conductivities in the temperature range of 75 °C to 300 °C.

Jan 1, 2006

By J. D. Miller, C. L. Lin

As the techniques and resolution for three-dimensional spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional X-ray microtomography offers a unique imaging capability. Spatial resolution on the order of 10 µm can be achieved with the use of microfocus X-ray generators. Recently, a state-of-the-art cone beam X-ray microtomography system was installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility was designed to obtain 2,048 by 2,048-pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind instrument can be used to obtain three-dimensional spatial reconstruction for many applications, such as three-dimensional liberation analysis, pore structure analysis of particle beds during filtration and the air-void system of concrete structures. The utilization of X-ray microtomography not only allows for the quantitative analysis of multiphase systems but also allows, for the textural characterization and determination of phase continuity. This paper presents information regarding the current use of this new facility and a review of potential applications for the advanced analytical system. Key words: Cone beam X-ray microtomography, Three-dimensional analysis, Material characterization

Jan 1, 2003

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By U. S. Sawant

During the last few years, Process Machinery Division, Rexnord, has conducted extensive research on the effects of cone crusher variables such as speed, throw and cavity design on the productivity of the crushers. Simultaneously, Rexnord&apos;s engineers have developed advanced design and testing techniques and criteria that assure efficient and reliable crusher designs. The combination of these two has resulted in a design of the 2390 Omnicone (1000 hp) crusher which fits on an existing 7 ft. Symons foundation and yet is capable of producing twice the tonnage compared to our 7 ft. super heavy duty (500 hp) crusher. Both speed and throw can be varied to give a wide application flexibility from making twice the tonnage to the finest product. The 2390 Omnicone also incorporates innovative features such as full balance, cavity clearing, adjusting under load with automation capability, maintenance-free seals, one head for all cavities, ease of maintenance and servicing, etc.

Jan 1, 1987

By A. J. Magerowski

Energy consumption is a main component of operational costs for the comminution of mineral bearing ores. Reduction of energy consumption has continually been addressed by mill operators and equipment manufacturers. Our testing over the last few years strongly indicates that the overall energy needed to comminute a mineral bearing ore can be brought down significantly, if more work is done in the crushing stages of the comminution circuit.This calls for uprating of the conventional crushing equipment into a new generation of crushing equipment to produce finer products. This will result in the emergence of new ideas in the design and application of equipment and corrnninution circuits.

Jan 1, 1986

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

By M. D. Flavel, J. C. Motz, G. V. Jergensen

Introduction Compared to the gyratory crusher, the cone crusher is character¬ized by its higher speed and a flat crushing chamber design which is intended to give a high capacity and reduction ratio for materials suitable to this type of processing. The aim is to retain material longer in the crushing chamber to do more work on material as it is being processed. A concept of how a piece of stone might flow through a secondary crushing chamber is shown in Fig. 45. The number of times material will be nipped during crushing will depend on material size, friability, and the geometry of the crushing chamber as well as its speed and eccentric throw. Cone crushers are usually specified in terms of closed-side setting (CSS) and a given quantity of material passing a particular square-mesh screen size. A criterion of product passing closed-side setting is often available. This value will vary according to the particular crusher design and the details of its applica¬tion. Essentially, cone crushers can be classified into distinct types, depending on their duty. Crusher sizes for all duties are described by terms arising out of common industry usage, such as 3-ft, 7-ft, etc., which refer to the crushing-head (mantle) diameter. At present the range of sizes available varies from approximately 2 to 10 ft diam. Weights vary in the range of 5 to 200 tons, and connected horsepowers range from 10 through 700. There are so many variations that specifics should be obtained from machine manufacturers. The crushing chambers that are fitted to various machines are also often referred to by terms arising out of common usage, such as standard for secondary crushers, and short head for tertiary crush¬ers, which refer specifically to the Symons design. Also used are more specific but equally vague descriptions, such as coarse, intermedi¬ate, and fine chambers. Some manufacturers such as Allis-Chalmers with their Hydrocone crushers refer to the model number of the machine by the feed opening and the diameter of the mantle. For example, a Model 10-84 Hydrocone crusher has an 84-in. diam man¬tle, and is capable of accepting a 10-in. diam sphere at the feed point to the crushing chamber. Rexnord and Telsmith define crushing cavi¬ties in their capacity tables as feed openings at minimum recommended discharge settings (closed-side settings). Each practice offers guidelines which should be carefully defined for the specific crushing problem. The utilization of a cone crusher depends on how well it is controlled and the features of the circuit in which it operates. Normally, it will operate in the range of 75 to 85% of the peak capacity. It is likely that industry pressures will call for a standarized de¬ applied crushing power. Experience has shown that the crushing process is more controllable if certain reduction ratios are adhered to for each stage. Technically, this is defined as that size of feed (in. or mm) of which 80% will pass, divided by the size of the product (in. or mm) which 80% will pass. Secondary Crushers These are the cone crushers which accept suitable feed size material either prepared by a primary crusher or occurring naturally, and reduce it to a size suitable for marketing in one stage, or make feed for subsequent crushing or grinding stages. Secondary crushers have feed openings of 4 to 25 in. in the larger (7-ft) models down to a 2&apos;/a to 4 in. in the smallest 24-in. models. Reduction ratios normally range between 3:1 and seldom more than 5:1. In the 7-ft models, the cone crusher typically makes a product all passing 2 in., but this is dependent on the machine design and properties of the material being treated. Secondary crushers most commonly operate in open circuit. They also are operated in closed circuit with a vibrating screen, depending upon product requirements and conditions where the reduction ratio does not cause excessive power draw and build-up of circulating load. Screening ahead of secondary crushers is generally recommended, especially where the feed contains more than 25% material smaller than the desired closed-side setting. Tertiary Crushers These are cone crushers that normally take secondary crusher product and reduce it to a marketable product or make it suitable for subsequent comminution steps. The reduction achieved is a func¬tion of the crusher design and the properties of the material to be treated. The reduction ratio is normally in the range between 1.5 and 2 to 1, and seldom more than 3 to 1. The tertiary crusher normally operates in closed circuit with a vibrating screen and makes a product smaller than all passing &apos;h or 5/8 in. Fine Crushers Sometimes these machines are called sand crushers and are called by various manufacturer brand names, such as Gyradisc, Hydrofine, V.F.C., and others. A cross section of a Symons Gyradisc crusher is shown in Fig. 46. Essentially, these crushers would be used in a fourth-stage crushing operation, but could be called on to reduce a screened feed size fraction from a secondary or primary crushing operation. This type of crusher normally receives feed no coarser than 1&apos;h in. that is scalped of all over-sized material and operates in closed circuit with a vibrating screen. For average materials, typical product is &apos;/e in. top size, although a -10 mesh product can be produced on those materials having suitable characteristics. The crusher is nor¬mally operated in a separate circuit from the main crushing plant because of the variations in output rates that are caused by varying physical properties in the feed. The reduction ratio is generally less than 2:1, and circulating loads are generally high. More interparticle crushing takes place in these machines than with conventional cone crushers and capacities can be more sensitive to changes in moisture content, feed size graduation, and other physical properties. Design Features For the various applications, crusher manufacturers normally have a range of crushers of different sizes and power ratings to select from.

Jan 1, 1985