Search Documents

By R. H. Watson

A paper read by J. A. H. Church before the Northern Alberta Branch last February described a method of working thick inclined coal-seams from the dip upwards, with the view to preventing fire risk by using water for the stowage of waste workings, and extinguishing a conflagration should such break out, was favorably received; but there was some doubt as to the cost of such a method, as it involves a retreating system, which might prove too expensive for practical adoption. Let us consider a typical leasehold such as we are familiar with in the Rocky Mountains. The leasehold is crossed at one end by a mountain river, which is cut by the outcrop of a seam of coal, 30 feet in thickness, pitching as shown on the drawing herewith, which also shows the general line of the outcrop in elevation through the leasehold, which is two and a half miles long and contains 1,500 acres. The average lift is about 600 feet above river level and drilling has proved that the coalseam can be tapped at a depth of 1,500 feet, 2,000 feet down the pitch from the outcrop in the river, all as shown in the illustration, which is typical enough of our mountain conditions to serve the purposes of comparison of methods. We take up the leasehold and invest $30,000 to pay for drilling and prospecting; $30,000 more for the price of the lease to locator or holder, and say $100,000 to pay for a railway spur (it might cost twice this sum, but we are only comparing two methods in the same location) and "now we are ready to consider equipment and the cost of development.

Jan 1, 1924

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By C. H. Mathewson

CHARACTER OF THE WORK IN HAND IN planning the present experiments, we have made a particular effort to secure that adjustment of working conditions which would render the forthcoming tests most serviceable by way of indicating the comparative properties of the three different commercial grades of copper used. More specifically, we have endeavored to obtain certain definite information with respect to the relative behavior under test of ordinary electrolytic copper and furnace-refined lake copper containing (a) a moderate percentage of arsenic and (b) a rather large percentage of arsenic, in addition to the usual content of silver and other impurities. These comparisons were made systematic and comprehensive by testing throughout a series of (eight) reductions running from 0 to 70 per cent. in the case of cold-rolled metal, and throughout a series of (15) temperatures running from 100° C. to 1,000° C. in the case of annealed metal. In other words, a survey of properties similar to that made by Grard,1 in the case of electrolytic copper, was here repeated (with modifications) and extended to two other commercial varieties of copper.

Jan 7, 1916

In order to test the applicability of elastodynamic codes in the modeling of mining related problems, comparisons are made between seismic data and numerical analyses. The dynamic finite difference program WA VE is used for the modeling of a horizontal stope in a deep mine. The slip along a vertical fault situated within the positive excess shear stress lobe of the stope initiates seismic waves. The stope-fault geometry is modeled in both two and three dimensions. The three dimensional non-slip weakening WAVE analyses correlate well with Brune's analytical model. For accurate modeling of the peak particle velocities predicted by McGarr's empirical relationship, it is recommended that a three-dimensional stope -fault model is used, with the amount of slip weakening dependent on the magnitude of the event.

Jan 1, 1995

By Steve P. Signer

A study of rock support interaction mechanics was conducted by the U.S. Bureau of Mines at the Jim Walter Resources No. 7 Mine, Brookwood, AL. Bolt loads and entry deformation were monitored at four sites in a tailgate roadway. Two sites were areas supported by fully grouted resin bolts, and two sites were supported by tensioned bolts that used resin-assisted mechanical anchors. The yield capacity of the tensioned bolts was 37 pct higher than that of the grouted bolts. To monitor loads, instruments were mounted on 16 bolts, which were installed during entry development in the standard bolt pattern. Additional instrumented bolts were installed as supplemental support just prior to the headgate pass of the first longwall. Instruments to measure roof movements included three-point roof extensometers and convergence stations. Readings were taken during section development and as each longwall panel passed the test area. The fully grouted bolts showed localized loads that were higher than loads on the tensioned bolts; however, overall loading magnitudes were similar. Many sections of the fully grouted bolts passed the yield point of the bolt steel (98 kN or 22,000 lb). However, the maximum strain measured at any loca¬tion was 50 pct of the ultimate strain, and there was adequate bolt length to transfer the high loads into the rock. Significant bending was detected at many points along the length of the bolts and seemed to be the most significant mechanism in support-rock interaction. Loads on the tensioned bolts did not exceed the yield point of 160 kN (35,000 lb). Entry deforma¬tion, supplemental bolt loading, and general entry degradation appeared to be slightly less at the tensioned bolt sites. Local geology and in situ horizontal stress were also observed to affect con¬ditions at the test sites.

Jan 1, 1993

By Frank Firmstone

IT is proposed to consider here only comparisons made between results obtained when the materials employed are precisely the same, two furnaces at the same works for example, or the same furnace under different conditions as respects temperature of blast, method of charging, etc. With this limitation, the most important point in the comparison is the amount of fuel consumed per ton of iron. This, in fact, is the only item in the prime cost of the iron which can properly be said to vary in consequence of changes in the furnace process ; for of the other principal items, the ore used per ton of iron, and also the amount of fluxing material, will depend on its richness, which, under the assumed conditions, will be practically invariable when taken over any considerable period; the labor cost also, from its nature, should be very nearly constant when estimated on the ton of iron. Moreover, as it consists principally in handling and moving material, it is greatly affected by circumstances quite independent of

Jan 1, 1876

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

By Peter A. Oshust

The EKATI Diamond Mine has successfully completed the development and commissioning of the Panda Underground Project to extract the ore below the Panda open pit. The dominant kimberlite domain of the Panda Underground, intermixed olivine-rich and mud-rich resedimented volcaniclastic kimberlite (RVK), is very similar to the kimberlite domain characterizing the open pit portion of the pipe. A sublevel retreat mining method is in operation underground at Panda; near-vertical blast rings are drilled and blasted into an open void. Broken ore is mucked with load, haul and dump trucks (LHD?s), sized underground then moved to surface through a conveyor system to the process plant. An advanced feasibility study is in progress at the Koala Underground Project. The Koala pipe is geologically more complex than Panda. The pipe below the open pit is comprised of at least five distinct kimberlite domains. There is a 100 m thick zone of incompetent low-grade mud-rich RVK between the open pit and the stable high-grade olivine-rich primary volcaniclastic kimberlite where mining will be initiated. As a result, it is proposed that Koala will employ sublevel caving; each blast ring shot would be confined and mucked in sequence to maintain the cave of the over-lying low-grade RVK ore. The sublevel cave method seeks to safely defer the mucking of the low grade ore to the latter part of the mine life.

May 1, 2006

By Cermets

Ti(C,N)-based cermets offer good high temperature strength, perfect chemical stability, excellent wear resistance, and relativly better machinability. In the present work, the tribological behaviors of Ti(C,N)/SiC sliding pairs lubricated in water and seawater were evaluated using a ball-on-disk tribometer. The experimental results show that a relatively low friction coefficient (about 0.025) can be obtained when lubricated with artificial seawater at the sliding speed of 200 mm/s, while the date is about 0.2 in purified water. The wear surface profiles and the lubricants collected after running-in process for the high/low friction conditions were compared. In addition, the effect of salt molar concentration of the lubricant on the Ti(C,N)/SiC friction properties was investigated. It was found that the smooth and flat surface is the premise to gain the low friction. At the same time, the proper concentration of silica colloid, which is affected by the salt ions, is also an essential one. Moreover, the high sliding speed (200 mm/s) is beneficial to achieve low friction.

Jul 31, 2018

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By Hans Jürgen Maier, Hans-Bernward Besserer, Gregory Gerstein, Florian Nürnberger

The formation and development of voids in both the single-phase ferritic steel DC04 and the dual-phase ferritic-martensitic steel DP600 are discussed. Various mechanisms and kinetics of void formation are considered regarding the influence of dislocation glide, precipitates and other parameters. Different characteristic locations in the microstructure are investigated at which strain concentrations during plastic deformation can occur and cause the formation of voids and microcracks. For the specimen preparation ion slope cutting is applied. Voids and cracks revealing ductile damage are analyzed by Scanning Electron Microscopy (SEM). Stress concentrations in consequence of plastic deformation could be shown by extinction contours on images recorded by Transmission Electron Microscopy (TEM).

Jan 1, 2015

By Tian Li

Simple compartmental models of a laboratory batch gibbsite precipitator were used to investigate the influence of the number of compartments, the local shear rate and solids distribution on the crystal size distribution (CSD) under the conditions where aggregation is the dominant mechanism. In the current work, a power law relationship was assumed between the local agglomeration and shear rate. The simulation results showed that both the local shear rate and solids distribution have significant effect on the CSD responses, and the interchanging flows has a lesser impact with its influence strongly depending on the former two factors. Overall, the results reveal that in an aggregation controlled precipitation system, the influence of each of the factors on the CSD depends on the local hydrodynamic conditions in the precipitator, as well as their interactions.

Jan 1, 2003

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

Testing is in progress to address compatibility issues with regard to long term storage of plutonium in contact with two different intermetallic systems. The two intermetallic systems are: 1. dental amalgam, i.e., mercury plus silver alloy powder, and 2. liquid gallium alloy plus copper powder. Both of these are plasto-metallic materials that undergo a solidification reaction at room temperature. Each system is allowed to react in contact with both high-purity alpha plutonium and a delta stabilized plutonium alloy at varying temperatures in an argon atmosphere. Wetting characteristics and possible interaction will be studied metallographically in the post-mortem condition. Complete results including metallographic examinations will be presented.

Jan 1, 1995

By Salvador Gómez, Rodolfo Espinosa, Jaime Bravo, Leopoldo Gallas

"Compañia Fresnillo, S.A. de C.V. - Proaño Mine, is owned by Industrias Peñoles S.A. de C.V. (Peñoles). The Proaño Mine, is one of the richest silver underground mines in the World, and for this reason, production capacity has always being expanded, based on generated reserves. Reserve generation has not being an easy task as this is a vein type deposit.This paper presents the growing stages at the Concentrator, for about the last twenty years; which can be listed as follows:1.,Increase in capacity from 1,000 to 4,500 tonnes per day, at several stages; on the same infrastructure, and without production interruptions.2.,Addition of a new flotation circuit to recover a zinc concentrate with a high silver content.3.,Installation of a semi-autogenous (SAG) mill, to replace a conventional crushing circuit. 4.,Modernization. Installation of an on stream analyser, an automatic reagent dosification system, 4500 ft3 unit cells, pressure filtration, a closed circuit video system to help process monitoring, an automatic ball addition system for SAG and ball mills, and on-line particle size analysers.5.,Silver recovery from old tailings, installing a 2,350 tonne per day treatment plant.INTRODUCTIONIndustrias Peñoles, S.A. de C.V. (Peñoles)Peñoles’ mission is to add sustainable value to non-renewable natural resources. Peñoles seeks to: build long-term shareholder value; provide customers with the highest quality product services; maintain productive long-term relationship with suppliers; develop and promote the capabilities of their personnel; foster mutually beneficial relationship with the communities in which operates; protect and preserve the environment."

Jan 1, 2002

By Ricardo Cortés Arana

El presente texto describe el ausentismo y las relaciones humanas como factores de productividad y equilibrio dentro de la compañía minera Atacocha. La asistencia continua al trabajo asegura la estabilidad del empleo y no altera el ritmo de producción de la planta minera. Por consiguiente, la ausencia inmotivada de un trabajador en la mina, afecta el rendimiento de los demás miembros y a la misma empresa. En cuanto las relaciones humanas, estas deben ser constructivas y basadas en el espíritu de cooperación entre obreros y patrones, así como destacar el conocimiento técnico, interés genuino y personal por las personas que trabajan en ella.

Jul 20, 1960

By Agustín Arias

El presente artículo describe brevemente la historia, métodos de explotación, mecanización, energía eléctrica, las plantas de preconcentración y flotación y el consumo de reactivos de la compañía minera Milpo.

Nov 1, 1954

By Jr. Moulton

Extractions of minerals from Searles Lake brines have taken place since 1873. Early operations were for borax and raw trona found on the surface, expanded after 1914 to include potash, salt cake, and soda ash. A new soda ash plant now in operation will double area production. The evaporite beds were formed by desiccation of Eastern Sierra runoff. The resulting series of brine-bearing salt beds supply the fluids necessary to feed the area chemical plants. Production methods include evaporation and crystallization for potash, borax, and salt cake; carbonation of brine to recover soda ash; and organic extraction of borax.

Jan 1, 1980

By G. F. Moulton

Extraction of minerals from Searles Lake brines has taken place since 1873. Early operations for borax and raw trona found on the surface were expanded after 1914 to include potash, salt cake, and soda ash. A new soda ash plant now in operation will double area production. The evaporite beds were formed by desiccation of eastern Sierra runoff. The resulting series of brine-bearing salt beds supply the fluids necessary to feed the area chemical plants. Production methods include evaporation and crystallization for potash, borax, and salt cake; carbonation of brine to recover soda ash; and organic extraction of borax.

Jan 1, 1982

By Óscar Queirolo

El presente trabajo explora la legislación nacional en cuanto a los ecosistemas que necesitan medidas especiales de gestión, la norma aprobada de compensación ambiental y los lineamientos internacionales vinculados con la gestión de ecosistemas en proyectos mineros en función de su pertinencia con la realidad minera peruana. Asimismo, propone una metodología a seguir para una adecuada gestión de los impactos sobre la biodiversidad y presenta algunos ejemplos tangibles desarrollados en nuestro medio y realidades similares.

Oct 21, 2015