Search Documents

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By Kim Le Roux

Cemented paste backfill (CPB) is a relatively new material that is increasingly being used in open stope mining across the world. The advantages offered by this high density tailings backfill include: a lower total cost associated with backfill placement, reduction of excess water underground; and the elimination of the need to process the tailings prior to placement. However, almost all backfill design is based on the performance of laboratory prepared samples since it is difficult to obtain undisturbed samples and conduct in situ testing due to the lack of access to backfilled stopes and the safety concerns in accessible areas. The logistical problems associated with conducting in situ testing and obtaining undisturbed samples of cemented paste backfill (CPB) has lead to the reliance in the mining industry on performance data obtained from laboratory prepared CPB samples. The degree to which these laboratory prepared samples represent the actual in situ condition is not well defined, partly because the influence of the mixing, transport and placement process on the material properties it is not well understood. Therefore, there is a need in the industry to understand how the material properties and hence the performance of the laboratory prepared CPB compares with in situ material. This paper reports the findings of an investigation into the in situ properties of CPB at a gold mine in Northern Ontario. A combination of in situ and laboratory testing, conducted on undisturbed samples, was used to quantify the in situ properties and performance of the CPB. These results were then compared to those of a laboratory based investigation of the same CPB. It is evident from this investigation that the bulk properties of the in situ CPB are different from those of the laboratory prepared CPB. The most significant observed differences are that the in situ CPB has a higher void ratio and a lower degree of saturation than the laboratory prepared material. The implication of these differences on the stability and performance of the CPB will also be explored in this paper. 1

May 1, 2002

By H. Möller, L. Mashigo, C. Gassmann

Wire-arc additive manufacturing (WAAM) is a directed-energy deposition technology that uses arc welding procedures to produce computer-aided designed parts, such as three-dimensional printed metal components. A challenge of additive manufacturing is the anisotropy. Interstitial elements play a significant role in the mechanical properties of Ti6Al4V of different grades. In this research, the mechanical properties of Grade 5 and Grade 23 Ti6Al4V were compared for this application. Samples were extracted from WAAM-produced Ti6Al4V walls in different directions (horizontal and vertical) and at different positions (top and bottom). The samples were subjected to optical microscopy and tensile and hardness tests. Grade 5 Ti6Al4V samples were found to have greater strength, greater hardness, and lower ductility, owing to the higher content of interstitial elements compared with Grade 23. The bottom samples had higher strength than the top samples, which is attributed to thermal cycling during manufacturing, resulting in different microstructures.

Jul 1, 2021

By E. Vilaescusa, J. Eloranta

The work presented in this paper investigates the influence of non-ideal detonation characteristics related to the blasthole diameter, base emulsion sensitivity (micro-balloon sensitised versus unsensitised) and percent emulsion on the explosive shock energy available to break rock using ANFOemulsion blends. A series of theoretical equal powder factor bench blasting patterns with hole diameters of 127mm (5”), 140mm (5.5”), 152mm (6”) and 165mm (6.5”) are compared to assess the non-ideal confined shock-state work energies. The Non-Ideal Shock Energy Factor (NSEF), which is the available shock energy per cubic meter of blasted material (MJ/m3) or kilocalories per cubic yard (kcal/yd3), is used to compare the different blasting patterns charged with a range of ANFO-emulsion blends from zero to 50% emulsion.

Jan 1, 2012

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Filippo Maria Leoni, Alessandro Bertero, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed by the U.S. Army Corps of Engineers (USACE) to reduce flood damages in the City of New Orleans and surrounding parishes through the construction of new pumping stations and better drainage canals, the SELA-22 project entailed the installation of a concrete covered canal along Jefferson Ave. and Prytania Street, in a highly urbanized portion of Uptown New Orleans, LA. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate underseepage and provide structural support for the concrete culvert. The USACE selected the jet grouting (Jet Grout) technology for the construction of the bottom plug. The bottom plug is between 18 and 21.5 ft thick with a maximum depth of approximately 40 ft, for a total length of approximately one mile. The treated soil comprised soft clays and silts with occasional presence of sands. Project specifications required 100% area coverage, a 28-days unconfined compressive strength of 100 psi and hydraulic conductivity of 1x10-6 cm/s, to be verified by testing specimens from cored samples. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid Jet Grout technology, and elected to perform a pre-construction bench scale laboratory mixing program to determine the most suitable grout mix features (i.e. binder type and proportions, binder content, etc.) to be applied in the subsequent field test and production stages. This paper will summarize and compare the results obtained from the different pre-construction and construction stages; interpretations of the data will be provided, along with general considerations regarding the effectiveness and significance of bench scale testing for jet grouting applications.INTRODUCTIONIn general, the effectiveness of the construction parameters in any ground improvement work depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2016

By B. R. Benner

Progressive improvements in crusher design, screening efficiency, and operating experience along with the downsizing of many taconite operations has resulted in the abilitv of some crushing plants to produce a substantially finer product. This finer product opens the possibility of replacing the rods in the rod mill with balls as is the current practice at Sydvaranger, Norway. If this replacement could be accomplished substantial savings associated with metal wear and the elimination of rod charging may be realized. The purpose of this study was to compare the performance of a mill charged with rods with the performance of the same mill charged with balls at the pilot scale. The first objective was to establish whether we could achieve the same throughput rate at the same mesh-of-grind in a mill in which the rod media has been replaced by balls. The second point was to determine whether the ball media would create a significant tramp oversize problem.

Jan 1, 1990

By Michael J. Beare

Requirements of both local permitting and international fundraising are forcing increasing numbers of projects in Russia and CIS to carry out dual technical studies. The principal focus of Russian mining project design is to satisfy local regulatory requirements. However, the technical documents are not generally accepted by international banks for project finance outside Russia. Similarly, international study documents are not accepted for permitting in Russia. The purpose of this paper is to compare and contrast Russian and international approaches to mine technical studies and draw conclusions from this. The Russian design and permitting system is centered around two key statutory technical documents termed the TEO Konditsy and the TEO Project. These documents are subject to regulatory approval and are broadly equivalent to the international prefeasibility study and the feasibility study respectively. A comparison of study criteria suggests similar approaches are used for the main technical disciplines in project design by the time projects are at the point of construction, but there is divergence on environmental matters where the OVOS (Russian ESIA equivalent) differs from an ESIA in some significant areas. The key differences relate to project footprint, level of technical detailed required for baseline studies, level of public consultation, consideration and disclosure of information, labour, coverage of community and social issues and the preparation of a Social and Environmental Management System (SEMS). It has been noted that the Russian Design Institutes often leave the detailed economic analysis until after the TEO Konditsy. A common problem is design teams tend to look for ?technological solutions? without due concern for project economics. The end result of this can be mines that are overcapitalized and hence sub-optimal. It can be concluded that Design Institutes have the monopoly on Russian permitting reports and this is likely to continue. Similarly, Russian institutes generally do not prepare feasibility studies to international standards and this is likely to continue to be the case. Therefore to achieve the requirement of dual technical studies, the international consultants and Russian Design Institutes will need to cooperate on a joint work program. Key issues will be to ensure the most appropriate option studies are carried out at the right stages, that project economics are considered throughout the study, and that the environmental work program covers the additional studies necessary for the ESIA.

May 1, 2009

By Douglas E. Rawling

The successful genetic manipulation of T. ferrooxidans is partly dependent on an understanding of the molecular biology of the organism. For optimum controlled expression of foreign DNA in T. ferrooxidans it is important that donor DNA is derived from bacteria that are genetically similar to T. ferrooxidans or placed under the control of T. ferrooxidans transcriptional promoters. Several structural genes and their controlling regions from T. ferrooxidans have been isolated and their DNA sequenced. These include the genes that encode the nitrogenase enzyme (nifHDK genes), glutamine synthetase (glnA gene) and the recA gene. These genes and the identical genes from a wide variety of other bacteria have been compared at levels of DNA sequence, protein sequence. Where possible, gene expression as well as transcriptional control and protein function of the cloned genes were tested in the enteric bacterium Escherichia coli. The two genes involved in nitrogen metabolism were either expressed or possessed the necessary elements for expression in other bacteria. In contrast the recA gene was not expressed in E. coli from its own promoter. The two gene products that would be tested (glnA and recA) were fully functional in E. coli. The relevance of these findings to the genetic manipulation of T. ferrooxidans is discussed

Jan 1, 1989

By Mark D. Hannington

Drilling of the active Trans-Atlantic Geotraverse (TAG) deposit during ODP Leg 158 indicated that the size of the mound-stockwork complex is approximately 3.9 million tonnes, including 2.7 million tonnes of massive and semi-massive sulfide (ca. 2% Cu) at the seafloor and 1.2 million tonnes of mineralized breccias (ca. 1% Cu) in a subseafloor stockwork. Quartz-pyrite veining in the stockwork zone extends from about 40 meters below seafloor (mbsf) to a depth of 95 mbsf. Siliceous wallrock breccias in the lower part of the stockwork grade abruptly into chloritized basalt breccias at the margins of the mineralized zone, and massive sulfides at the flanks of the deposit onlap relatively unaltered, partially hematized basalts. The pipe-like dimensions of the stockwork zone do not exceed the diameter of the sulfide mound. Comparisons with samples collected during earlier dive series confirm that the vent complexes at the surface of the mound are not representative of the bulk composition of the deposit. Dramatic vertical zonation of metals within the mound suggests that a long history of hydrothermal reworking has effectively stripped the constituents that are soluble at lower temperatures from the massive sulfides and concentrated them at the top of the deposit through a process of zone refining.

Jan 1, 1998

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

Comparison of the Zadra, Anglo-American and organic solvent procedures for desorption of gold from activated carbon loaded in carbon-in-pulp gold circuits indicates that the Anglo American and the organic solvent procedures are considerably more effective than the commonly used Zadra procedure. Organic solvent elution procedures, particularly those using acetonitrile and acetone, can provide effective gold elution and very high concentrations of gold in eluate solutions. The operational simplicity and effectiveness of the Anglo American procedure would appear to make it the most satisfactory procedure available at the present time but this may change as the solvent elution procedures become better developed. INTRODUCTION The carbon-in-pulp technique has been introduced into the gold processing industry to by-pass the often lengthy CCD and filtration steps required in the conventional Merrill Crowe cyanidation procedure for gold recovery. Adsorption of gold on to carbon is also a valuable technique for recovering trace amounts of gold from low level waste streams from conventional processing procedures.

Jan 1, 1982

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of the general negative perception of mining activity by the public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to control vibration at neighboring structures.

Jan 1, 2013

By N Yarahmadi

Characterization of pore pressure is critical for appropriate design of tailings dams. Furthermore, if seepage rates through tailing embankments increase unexpectedly or become uncontrolled, undesirable conditions may prevail to progress piping or internal erosion that could lead to the dam’s instability or ultimate failure. A three-dimensional seepage analysis was performed on a tailings dam using finite element method to find the rate of seepage and pore water conditions in the embankment and foundation. The results were then compared to a conventional two-dimensional seepage analysis carried out on the typical cross section of the embankment and the field data acquired from the instrumentation system. Considering the monitoring data, comparison of seepage analyses results for the two and threedimensional models, showed that the results of the conventional two-dimensional seepage analysis are significantly underestimating reality. Relying on two-dimensional seepage analyses might result in underestimation of seepage rates and impact the safe operation of tailings dams. Similarly, unrealistic prediction of pore water pressure conditions, based on simplified seepage analyses, can lead to overestimation of the rate of strength gain of material and consequently safe embankment raising rates.

Jul 1, 2021

By Wael Abdellah

Mine haulage drifts are the primary access to the mining blocks of an orebody in a multilevel mining system of a tabular ore deposit. The stability and functionality of haulage drifts are thus crucial to the success of a mining operation. Drift instability could lead to serious consequences such as injuries, production delays and higher operational cost. In this paper, the performance of the haulage drift stability is evaluated on the basis of the primary rock support system comprising 1.8 m resin grouted rebars in the drift walls and 2.1 m long bolt in the back. Two failure criteria namely the extent of Mohr-Coulomb yield zones around the drift, and linear elastic brittle shear failure are adopted and compared, with respect to lower level and same-level mining and filling sequence in the vicinity of the haulage drift. The case study is one of the #1 Shear East zone of the Garson Mine in Sudbury, Ontario. Random Monte Carlo (RMC) technique, which has been previously established to assess the haulage drift stability, is employed in this investigation. The RMC technique is used in conjunction with finite difference modelling software FLAC for random assignment of model input parameters in the FLAC grid. Deterministic model results reveal the drift behaviour in terms of deformation (convergence) and mining-induced stress distribution. Comparison between the two different criteria is carried out to determine which method is most suitable in evaluating unsatisfactory drift performance. The results are presented in terms of probability of instability and categorized with respect to failure condition and mining step. It is shown that the brittle shear failure condition based on linear elastic response calls for enhanced support system at a later mining step than what Mohr- Coulomb yielding condition does. The paper presents a detailed discussion of the stochastic analysis results.

Jun 1, 2012

By George A. Desborough, David L. Fey, Stanley E. Church

About 100 mine-waste dumps from past metal exploration and mining in Colorado and Montana were sampled using surficial-sampling methods for laboratory studies of the minus-2-mm fraction. In the laboratory, the composite samples were split into l00g samples that were leached to assess their acid-generation potential and associated release of potentially toxic metals that may degrade water quality in the headwaters of the Animas River watershed in Colorado and the Boulder River watershed in Montana. Two leach methods were studied: a passive leach using de-ionized water, and a more aggressive leach following the EPA-1312 method. The resulting pH values of the leachates using both methods are comparable. The concentrations of sulfate and several, but not all, dissolved or water-soluble metals are higher in the EPA-1312 leachates than in the passive leachates; however, the overall trends of the data are very similar. The passive leach method is less labor intensive and may be more representative of the natural weathering process occurring on the mine-waste dumps, simulating the natural precipitation and snowmelt. Three chemical characteristics of mine wastes studied here provide a relative ranking of mine-waste dumps for the purpose of determining priority for removal or remediation. These characteristics are: net acid production (NAP), sum of dissolved toxic metals (?As+Cd+Cu+Pb+Zn), and dissolved iron in leachates. Ranking can be done evaluating plots of NAP versus the sum of dissolved toxic metals, and NAP versus dissolved iron. These two plots serve as a basis for relative ranking of polymetallic-vein and acid-sulfate mine wastes studied. This ranking scheme may apply to mine wastes from production of other deposit types in other watersheds.

Jan 1, 2000

By A. Y. Senchenko, Y. V. Kulikov

"The most common technique for selection of grinding equipment is the Bond method implying determination of a ball mill work index (BWi). The method is perfect for greenfield projects where a ball mill must be sized to grind an ore to 80% passing 75-100 µm. Finer grinding will require application of specific correction factors to a standard equation since initially the method was not designated for sizing of fine (minus 75 µm) grinding mills. Significant issues are related to selection of grinding equipment for treatment of originally fine materials when the standard procedure is not applicable. In 1984, Levin published his special technique titled as “A proposed test for the determination of the grindability of fine materials”, where he offered to use the standard Bond ball mill for determination of a specific grinding energy. However, this method did not meet with wide recognition. In 2017, Institute TOMS under guidance of JKMRC’s specialists performed a testwork aimed at verification of a new universal technique for determination of grindability of initially fine materials. An object was to test three aged tailings samples for the subsequent modelling of comminution circuit and evaluation of potential throughput of the existing ball mills with final grind size of ?80 passing 53 µm. In parallel with development of the universal approach, TOMS’ specialists carried out tests according to the Levin method in order to compare the data resulted from two methods. The results from lab ball mill testing on three products following the alternative test methods are presented in this paper along with the testing methodology and results analysis. Specific energy was calculated for regrinding of the materials to the required size. Difference of the examined methods and assessment of their applicability for sizing of full-scale equipment are explored."

Jan 1, 2018

By C Artica

Two quantitative methods for Mineral Resource classification have been applied to a copper skarn deposit beneath a large open pit that is mining a world-class porphyry complex. A drill hole spacing study (DHSS) using the single block kriging method (SBK) and a conditional simulation method (CS) were applied to the skarn deposit and the results compared. Inputs to both processes included the proposed mining rate and stope designs to estimate the likelihood of achieving grade and metal production targets. Mineral Resource classification of the deposit considers the relative precision of tons, grade and metal predictions over quarterly and annual production periods. These relative precision estimates are calculated at 90 per cent confidence interval (CI). The SBK method represented the production period as a single large block. Kriging estimates were performed in the large block for various synthetic drill hole grids, and the estimation errors derived. The error was assumed to be normally distributed due to the large block size and quantity of samples, allowing CIs to be deduced. The CS method followed a conventional sequential Gaussian simulation workflow where grades were simulated with a 5 ft × 5 ft × 5 ft grid node spacing inside mineralisation domains. Each realisation was then averaged up to monthly production volumes represented by a combination of designed stopes, and the coefficient of variation (CV) for the averaged grade was calculated. CI on the relative precision of grade predictions were then deduced from the CVs. The two methods produced similar results; despite being calculated independently. CS results were used to report uncertainty in the proposed life-of-mine plan and highlight areas for additional drilling. SBK results were used as the basis for Mineral Resource classification as this method has been previously applied to the skarn deposit.

May 24, 2023

By S. D. Thompson, G. T. Lineberry, A. J. Basu

Conveyor belt haulage has become the preferred mainline transport method in underground coal mining, especially for multi-unit mines. Proper designs for belts (width and speed) and surge bins (placement, capacity, and discharge rate) are necessary to achieve efficient mine haul- age. Two computer simulation models, CMBCS and BELTSIM, available for designing these parameters were compared. These comparisons included modeling, input data requirements, statistical flexibility, accuracy of simulated loading, and execution time.

Jan 1, 1991