Search Documents

By H. R. Manouchehri

"Pyrrhotite (Po) is one of the most abundant sulfide minerals in processing industry and must be rejected in most cases. Particularly, Po rejection and its selectivity against pentlandite (Pn) have long been a challenge due to similarities in the mineral composition of the two minerals and the collectorless flotation characteristics of Po. Xanthates have been widely used to promote sulfide mineral flotation; however, in the presence of xanthates, the redox potential established at the mineral/solution interface is most important, determining the flotation performance. In this paper, the importance of electrochemistry in Po and Pn flotation has been demonstrated and a comprehensive study was conducted on two different feed streams (i.e., magnetic concentrate and scavenger cleaner streams, containing magnetic and nonmagnetic forms of Po, respectively), from Vale’s Clarabelle Mill in Sudbury, Ontario, with an objective to determine if improvements in Po rejection and Pn recovery could be achieved by controlling pulp electrochemistry. By conducting a series of flotation tests under different Eh conditions and reagent usage schemes, it was revealed that higher Po content in the magnetic stream may protect Pn from being oxidized, improving Pn recovery. The results indicated that at low oxidizing pulp chemistry, the rest potential for the Pn is still high enough to allow the formation of dixanthogen to promote its flotation. Using a Pt electrode, it was found that by controlling pulp potential at -50<Eh< +50 mV, the Pn recovery and Po depression would be satisfactory. The results, using mineral electrodes (Outotec Chena analyzer), indicated that selective separation can be achieved if low-to-moderate oxidation potentials (0 to 100 mV) or reduction (0 to -100 mV) potentials are monitored using Pn and Po electrodes. Mixing two streams at 50:50 wt % would be possibly beneficial in selective separation.IntroductionPyrrhotite (Po), Fe1-xS, is one of the most abundant sulfide minerals in the processing industry. It is an iron-deficient sulfide that occurs either in monoclinic or hexagonal form. The monoclinic one is richer in sulfur and is ferromagnetic, whereas the hexagonal Po is poorer in sulfur and has no magnetic properties. In general, the ferromagnetic properties of natural Po increase with increasing sulfur content. Although Po holds significant iron content, it is not used as a feedstock for the iron and steel industry due to the difficulty in achieving complete removal of sulfur. The common availability of iron oxide ores makes the iron sulfides irrelevant for the steel industry."

Jan 1, 2015

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

"The paper treats the spatial aspect of mine sequence optimization. This aspect is revealed in the context of determination of the optimum number of cutbacks of an open pit mine. Cutback mining is a dominating method currently in base\precious metal mining and it is based on a pseudo-economic discretization of the pit space by using advanced pit design algorithms. The result of the implementation of such approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks for maximization of the project value. A mathematical solution of this problem is developed with the utilization of a combinatorial analysis. The solution provides a multi-variant investigation of the optimum mine sequence with the implementation of an author’s method for production scheduling optimization, which uses the Net Present Value as a criterion for assessing the economic efficiency of mine sequencing. A case study is provided for the conditions of a hypothetical open pit gold mine to illustrate the applicability of the approach. The results obtained reveal the complex nature of the variation of the Net Present Value as a function of the cutback geometry. INTRODUCTION The mine sequence optimization in open pit mining is a procedure that predetermines the efficiency of the production scheduling optimization. From a technological standpoint, the mine sequence optimization deals with two aspects – spatial and time. Each of them plays a tremendously important role in searching for the optimum solution of the open pit design problem. Original results on the time aspect of mine sequence optimization are published by Halatchev [2002]. They reveal a wide range of the Net Present Value (NPV) variation for a multi-variant arrangement of mine sequence over time and using a fixed geometry of the cutbacks, which determines the economic potential of a single open pit mine from a deterministic standpoint. The results show a range of NPV variation up to 30% depending on the stripping ratio of the mine. The effect of this variation is mainly due to the implementation of the mine planning principle of waste deferment in the scheduling optimization and using all theoretically possible variants of mine sequence arrangement by the inclusion of the bench sequences over the Life-Of-Mine (LOM) in the production process."

Jan 1, 2015

By J. F. Mack, P. R. Michael, J. M. Shapaka, S. J. Self, M. W. Richmond

"On October 11, 2000, an estimated 306 million gallons of water and coal waste slurry drained from an impoundment in Martin County, eastern Kentucky into an adjacent underground mine. Approximately 230 million gallons of the water and slurry discharged from two underground mine portals and affected over 75 miles of streams in Kentucky and West Virginia. In response to this and several other similar events, the U.S. Office of Surface Mining Reclamation and Enforcement (OSMRE) commissioned an oversight study that evaluates how well state and federal regulatory programs established under the Surface Mining Control and Enforcement Act are ensuring that impoundment operators are minimizing the potential for impoundment-basin breakthroughs. The study focuses on slurry impoundments constructed in the hollows of Appalachia where numerous coal seams and steep topography combine to result in a large number of mined seams intersecting and underlying impounding facilities. Factors under consideration include: (1) full accounting of all mineable coal seams intersecting and underlying the impoundment; (2) identification and accurate location of underground mines close enough to the impoundment to potentially affect its stability; (3) assessment of the stability of coal barriers between the impoundment basin and adjacent mines, and stability of roof rock and pillars in mines subjacent to the structure; (4) determination of the flowability of the impounded slurry when expanding or undermining the facility are being considered; and (5) measures undertaken to reduce breakthrough potential when necessary. The oversight study began in 2012 after program-evaluation criteria were defined in an OSMRE technical position paper. The study is scheduled to be completed in 2017. BACKGROUND The Surface Mining Control and Reclamation Act (SMCRA) authorizes the disposal of coal mine waste by constructing a coarse coal mine waste embankment across a valley and pumping the fine coal mine waste (slurry) into the resulting basin (Figure 1). A concern shared by many engineers, geologists, and mine inspectors familiar with coal mine waste slurry impoundments is related to the common occurrence of underground mine workings adjacent to or beneath the impoundment: the potential for slurry “breakthroughs” into mine works and subsequent breakouts into the surface waterways (Figure 2). On October 11, 2000 a combination of coal refuse slurry and water from the Big Branch impoundment in Martin County, Kentucky broke through into an underground mine and subsequently discharged into the receiving streams. The location of the point of breakthrough, pathways of slurry/water flow within the mine workings, and two points where the liquid exited the mine are shown in Figure 3. An estimated 306 million gallons of water and coal refuse slurry drained from the impoundment into the adjacent underground mine. Approximately 230 million gallons subsequently discharged from the underground mine at two portals."

Jan 1, 2015

By K. Feledi

"A booster fan is an underground mechanical ventilation equipment installed in series with a main surface fan that is used to boost the air pressure provided by the surface main fan passing through it. As mining continues to expand and go deeper, the need for improved and efficient ventilation increases. This has led to the use of booster fans and other auxiliary ventilation devices in underground mines. This paper details experiments and results carried out at Missouri S&T Experimental Mine that investigated air leakage and recirculation caused by the use of booster fans. The results were compared with the situations where booster fans are used and not used.The variables considered were the booster fan blade angle and the fan combinations. Air quantity measurements were taken at each individual stopping under a number of scenarios and across four blade angle settings. The first set of situations examined were; the main surface Joy fan only running, the main Joy, and the west booster fan running, and the main Joy fan and east booster fan running. Observations were made which lead to the conclusion from the experimental analysis that booster fans affect the behavior of leakage and recirculation. The locations of the booster fan and the blade angle setting have the most effect on leakage and recirculation. To limit the potential for system leakage and recirculation, the location and size of a booster fan in a ventilation system should be thoroughly evaluated.INTRODUCTION Missouri S&T Experimental Mine ventilation system The Missouri S&T Experimental Mine has two shafts. One currently serves as the main intake shaft. Air is forced through the main shaft by a Joy Manufacturing Vane Axial fan and follows the direction shown on the map on Figure 1. The air is currently naturally exhausted through the Wheeler portal. As indicated on the map there are eight stoppings in the mine, with stoppings number 2 and 8 fitted with man doors. The mine also consists of three raises which are either fully or partially blocked, two portals with one acting as an exhaust and the other generally closed by a hydraulic Kennedy door."

Jan 1, 2015

By B. N. Conley, K. D. Luxbacher

"The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. The explosions that occurred at the Sago Mine in 2006, the Darby Mine in 2006, and the Upper Big Branch Mine in 2010 have caused a ripple in an otherwise steadily improving safety record. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reached a level of diminishing returns. Risk management, a safety approach that has been successfully applied in various industries including mining across the world, may provide a means to surpass the safety plateau in the U.S. RISKGATE is an Australian risk management program for mines that shows great potential for application in the U.S. However, fundamental differences between the coal mining industries in Australia and in the U.S. prevent direct implementation. This paper discusses aspects of the RISKGATE body of knowledge that require some adaptation before this program may be applied to the U.S. mining industry. INTRODUCTION The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reach a level of diminishing returns. In order to combat this stagnation in performance, a modification to the manner in which the mining industry approaches worker safety may be warranted. The implementation of a risk management based approach presents a potential method for not only surmounting the current safety plateau but also for achieving the long desired objective of zero harm. RISKGATE a risk management body of knowledge designed for the Australian mining industry that shows great potential for application in the U.S. This paper discusses aspects of the RISKGATE body of knowledge that require adaptation before implementation in the U.S. mining industry. These adaptations are based on differences in operating practices and governmental regulations. This discussion will focus on the three major U.S. risk areas of explosion prevention, ground control, and moving equipment."

Jan 1, 2015

By P. James

"INTRODUCTION High sulfate (SO4-2) levels often occur in MIW (mining influenced water) either as the result of oxidation of sulfide minerals exposed by mining activity or by deliberate addition – commonly by sulfuric acid (H2SO4) use in hydrometallurgical leaching activities. Increasing regulation of sulfate discharge is creating new pressure to treat or mitigate sulfate release to prevent its entry into the environment. Current treatments include precipitating as gypsum during lime treatment, filtration separation using membranes such as reverse osmosis and nanofiltration technology, and biological elimination via methods like constructed bioreactors. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform can also remove sulfate from target streams as a byproduct of its usual primary treatment focus points of metal species elimination and/or pH adjustment.[1-6] This powerful new capability can mitigate sulfate contamination and recover the sulfate in a useful and potentially saleable form as a byproduct of improved primary treatments focused on enhancing production or treating waste. This provides a new treatment opportunity and value proposition for lowering overall sulfate consumption/addition or creating new revenue to defray conventional treatment costs. The DEMET Alternative DEMET utilizes a patented electrolytic technology platform employing proprietary dynamic high surface area electrodes in innovative configurations to achieve a variety of novel selective chemistries. DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells. Secondary reactions (Figure 1A) which could also occur at the cathode (plating/electrowinning, precipitation/scale formation, etc.) are controlled through process tailoring and operation parameter selection. Additionally, DEMET‘s innovative dynamic system mitigates potential fouling and electrode occlusion or shorting challenges which could occur when process particulars demand some of these secondary side reactions occur."

Jan 1, 2015

By M. U. Khan

"Underground mine diesel equipment generally offers more flexibility as compared to electric powered systems. Diesel exhaust is an adverse agent which affects the health of underground miners. The National Institute of Occupational Safety and Health (NIOSH) regard diesel exhaust as carcinogenic. The NIOSH 5040 method is an established technique for measuring Diesel Particulate Matter (DPM). This process inherently involve a lag time before an accurate exposure determination can be made during which miners are potentially overexposed to DPM. This issue can be addressed by using realtime DPM monitors. This paper presents underground mine shift average based and realtime monitored DPM values monitored in US mines. A FLIR Airtec instrument has been used for realtime measurement whereas shift average based DPM has been determined by the use of NIOSH 5040 method. A log of diesel equipment movement was kept. DPM concentrations versus time were plotted and analyzed. High DPM sources were identified and the FLIR Airtec was demonstrated to be satisfactory for realtime DPM measurements. INTRODUCTION The use of diesel equipment in mines is an attractive option due to its ability to convert a large fraction of available energy into useable work. Diesel engines are rugged, dependable and fuel efficient. It is very common for diesel engines in heavy duty trucks to have a life of 1,600,000 km [Anon, 1999]. Generally in underground mines compared to electric powered equipment, diesel equipment provides more maneuverability. It can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment keeping in mind the recent developments in other energy alternatives [Anon, 2001a]. A harmful aspect to the use of diesel as a fuel is its resultant emission as an adverse environmental exposure agent. Generally diesel particles are approximately one order of magnitude smaller than respirable dust aerosols in underground mines (typically less than one micron in size) [Kittelson, 1998]. Force of gravity has less effect on DPM due to its small particle size. The phenomenon of less gravitational attraction increases the settling and residence time of DPM in the mine atmosphere. High residence time of DPM as compared to other mechanically generated particles increases the chances of diesel particles deposition in the human respiratory tract. The small sized diesel aerosols penetrate deeply into regions of the human lung [Morawska. et al. 2005], which increase the health risks associated with long term exposure to diesel aerosols. Published studies documented the adverse health effects of DPM exposure [Walsh M.P., 1999]. Continuous and long term DPM exposure can result in respiratory disease, lung cancer, reduced lung capacity, and heart disease. NIOSH has declared that the reductions in DPM exposure would reduce cancer risks. In underground mines DPM determination is a challenging task and it is becoming a matter of serious concern due to the harmful health effects associated with the exposure of DPM. The current study involves the determination of realtime and shift averaged based DPM in underground mines of United States of America (USA). Realtime DPM was measured using FLIR Airtec monitors and shift averaged based measurement was performed by the MSHA approved NIOSH 5040 method. FLIR Airtec uses laser scattering approach to measures the Elemental Carbon (EC) component of the DPM. The results from the FLIR Airtec were compared with the results of NIOSH 5040 method and its performance was found satisfactory."

Jan 1, 2015

By Yuexin Han, Mu. Yufan, Yanjun Li, Peng Gao, Yongsheng Sun

"The objective of this study was to evaluate the effect of reduction temperature, reduction time and binary basicity on the size of metallic iron particles in coal-based reduction products of an oolitic iron ore. The particle size distribution behavior (i.e., cumulative passing percentage and mean size of metallic iron particles) during reduction was investigated in detail. Results showed that the particle size distribution of metallic iron particles was strongly influenced by reduction temperature, reduction time and binary basicity. The cumulative passing percentage and mean size significantly increased with reduction temperature and time in the entire range of the experiments. All curves of cumulative passing percentage versus particle size under different conditions demonstrated a similar trend (continuous increase). The size distribution parameters and mean size slightly increased with increasing binary basicity and significantly decreased when the binary basicity exceeded 1.0. The size of metallic iron particles could be controlled by adjusting the reduction conditions during coal-based reduction.IntroductionThe increasing demand for iron ore coupled with diminishing high-grade iron ore reserves has resulted in the urgent need for innovative technologies in order to use refractory iron ores. Oolitic iron ore is a typical refractory iron ore with tremendous abundance globally. Based on published literature, oolitic iron ore reserves are approximately 140 million tons in Europe, 10 billion tons in China and 66 million tons in Pakistan (Kazmi and Abbas, 2001; Wu et al., 2011; Yu and Qi, 2011; Sun et al., 2013a). Therefore, the efficient exploration and use of oolitic iron ore resources can play a significant role in easing the mineral resource crisis in the iron and steel industry. However, oolitic iron ore cannot be effectively upgraded by traditional beneficiation methods due to its mineralogical characteristics (e.g., low grade of iron, poor liberation of iron minerals and high phosphorus content) (Li et al., 2011b; Sun et al., 2013b).Researchers recently proposed coal-based reduction followed by magnetic separation to recover iron from refractory iron ores (especially oolitic iron ore) and a certain degree of breakthrough was achieved in both theory and practice. In this technology, iron minerals in the ore are directly reduced by coal to metallic iron, which grows into particles of different sizes. After comminution and liberation, metallic iron is concentrated by magnetic separation (Srivastava and Kawatra, 2009; Sun et al., 2013a; Li et al., 2011b; Sun et al., 2013b; Li et al., 2011c; Gao et al., 2013). Sun et al. and Gao et al. used this technology to examine the recovery of iron from oolitic and Bayan Obo iron ores, respectively (Sun et al., 2013a; Li et al., 2011b; Li et al., 2011c). Metallic iron powder with more than 90% iron content was obtained as the final product, which could be used directly in steel production."

Jan 1, 2015

By K. N. Han, H. C. Cho, R. Kim

"A comprehensive analysis of the effect of OH- on various cations in hydrometallurgical systems has been investigated. Cations chosen for this analysis included groups 1A and 2A, rare-earth elements and other common transition metal ions such as Cu2+, Fe2+, Fe3+, Mn2+, Ni2+, Co2+, Ag+, Cd2+, U4+, UO2 2+, Hg2+, Al3+ and Zn2+. The Newton-Raphson technique was used to calculate and plot various metal species over a wide range of pH. This study has clearly shown that by adjusting the concentration of OH-, the separation of Fe from Mn, U from V, Ce and Eu from other rare-earth elements, and In from Sn is possible. The effects of hydrated metal ions on the separation and removal of various metals from each other under various conditions is discussed.IntroductionThe primary purpose of hydrometallurgical processing is to extract, remove and purify various metals from diverse sources. Hydrometallurgists are frequently preoccupied by the extraction of cations in metallic form, but overlook the important role anions play in such processes. A proper choice of anions can determine the fate of successful extraction, removal and purification of metals (Esmaeili et al., 2005; Brbooti et al., 2011; Wei et al., 2005; Jeppesen et al., 2005; Al-Tarazi et al., 2004), and also separation (Farha et al., 2011; Sevenich and Fritz, 1983; Rashid, 1974) of cations from various solutions.In this study, the authors have examined some of the effects that anions play in various solutions. The anion considered in this study was the first hydroxide, OH-. Other anions, such as Cl-, Br-, I-, and CN-, will be dealt with in the second part of the series of two papers."

Jan 1, 2015

"Foreword by Emily SarverAssistant professor, Mining and Minerals Engineering, Virginia Tech, Blacksburg, VAThe Mineral Processing Division hosted its fifth Student Poster Contest during the 2014 SME Annual Meeting and Exhibit in Salt Lake City, UT – and, by all accounts, it was a huge success! This year, the contest more than doubled in numbers of individual entries and schools represented. A total of 30 students participated, including 23 graduates and 7 undergraduates, representing 13 US and international institutions: Colorado School of Mines, Michigan Tech, Missouri University of Science and Technology, Montana Tech, New Mexico Tech, South Dakota School of Mines, University of Kentucky, University of Utah, Virginia Tech, West Virginia University, Autonomous University of Chihuahua (Mexico), UNAL Medellin (Colombia), University of British Columbia (Canada). In addition to constructing their posters, students submitted abstracts and gave short oral presentations highlighting their research. Based on tallied scores from all three components of the contest, the judging panel selected 1st, 2nd and 3rd place winners at the undergraduate and graduate levels, which were announced during the MPD Luncheon on February 26.In the undergraduate division, University of Utah’s Lucas Pich was awarded the 1st place prize for his poster “Solid-liquid mixing studies in lab-scale flotation tank using electrical resistance tomography.” His extended abstract is included in this issue of Minerals & Metallurgical Processing. Joshua Chidester, also of Utah, won 2nd place for his poster presenting “Evaluation of detectors for radiotracer RTD measurement by MCNP.” And Lucas Rojas-Mendoza, of UNAL Medellin, took 3rd place for his poster on “Preg-robbing in Colombian gold ores.”In the graduate division, 1st place went to Caelen Anderson, of the Colorado School of Mines, who also placed in this contest in 2012 and 2013! The 2nd and 3rd place prizes were awarded to Jacob McDonald and Joseph Halt, respectively, both of Michigan Tech. Extended abstracts describing the work of these up-and-coming researchers are also included in this issue.The 2014 Contest was chaired by Emily Sarver (Virginia Tech) and Lisa Schlink (Freeport-McMoran Copper and Gold, Inc.). Aaron Noble (West Virginia University), David Perkins (Derrick Corporation) and Derek Novotny (Eriez) graciously served on the judging panel this year.Special thanks are extended to all sponsors of the 2014 MPD Student Poster Contest, and to all student participants. Please watch for upcoming details on the 2015 Contest. We look forward to seeing you in Denver!"

Jan 1, 2015

By B. I. Pålsson, H-Å. Häggblad, J. F. Stener, P. Jonsén

"Understanding mill charge motion is important. In the charge, the center of gravity is shifted from the rotational center of the mill system, and its motion is induced by rotation of the mill. At the same time, the charge creates a torque in the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to this motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty of measuring inside a tumbling mill. Experimental measurements in a lab mill were done for a number of load cases: varying feed material, mill filling, mill speed and pulp liquid. The mill is set up to measure the charge-induced torque. The accuracy is good, with relative uncertainty less than ± 2% for relevant load cases. A full three-dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill startup behavior for torque and mill power. This proves that the model is physically correct, and can be used for modeling large-scale mills.IntroductionUnderstanding of the charge motion within the mill is of importance in mill optimization. The breakage of ore particles and the wear of liners/ball media are closely linked to the charge motion. To study these phenomena in a physically correct manner, appropriate numerical models for different parts of the mill system must be used. Validation of these models is of major importance. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behavior of the mill charge.For structural analysis, the finite element method (FEM) is the most developed and most frequently used numerical method. FEM is a numerical solution method based on continuum mechanics modeling. A constitutive relation for the actual material is described, and the governing equations are solved in Zienkiewicz and Taylor (2000). Varieties of different constitutive models for a large number of materials are implemented in modern FEM code. The computability of nonlinear problems in solid mechanics is investigated in Belytschko and Mish (2001), among others."

Jan 1, 2015

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By P. Conrad, S. Rosenthal

"Engineers remain in demand. Job opportunities in the United States still exceed the number of students graduating from college with degrees in Mining Engineering. Although enrollment is up for freshman studying Mining Engineering, many of those students will either change majors or not complete their degree, maintaining that deficit of available Mining Engineers. What can be done to ensure that enough Mining Engineers will graduate to fill the needs of the mining industry over the next ten to 20 years? The authors believe that this need can be met by recruiting students to Mining Engineering programs who are genuinely interested in working in the mining industry. With this in mind, Montana Tech conducted its first Mining Engineering camp in July 2014 to get junior and senior high school students interested in careers in the mining industry by showing them that Mining Engineering is both an exciting and rewarding career. This paper discusses What a Blast! The 2014 Montana Tech Mining Camp. INTRODUCTION The concept of summer camps for high school students is not new. For example, Missouri University of Science and Technology has offered their “Explosives Camp” for several years. A large percentage of attendees to these camps discover or confirm an interest in Mining Engineering and enroll in the school’s program. The Dean of the Montana Tech School of Mines and Engineering challenged department heads to develop and offer summer camps for prospective high school students to get a taste of engineering with the goal being to improve recruitment for each discipline. Mining Engineering embarked on the concept of a summer camp in 2013 with a concept to provide a week’s experience in Mining Engineering during the summer of 2014. What it takes to progress from concept to reality, with some of the learnings to be shared, follows."

Jan 1, 2015

By R. J. Visintainer, J. M. Furlan

"Due to the time-consuming nature of froth testing in a laboratory environment, practical limitations require the development of a method of applying a single set of performance test data (Visintainer and Whitlock, 2012) obtained for a single froth pump at a given speed to a range of froth pump speeds and sizes, % air content and liquid viscosities. Head, efficiency and flow all vary as functions of both liquid viscosity and air content. As such, it is necessary to develop a technique that can be used to interpolate from existing test data in order to predict froth performance for pumps of various sizes running at variable speeds. Details of the technique developed in order to achieve this goal, as well as the insights gained from analysis of the resulting regressions, are discussed. Additionally, comparisons are made between the performance predictions of this test-derived method and those of the Hydraulic Institute standard for the effects of liquid viscosity on centrifugal pump performance (ANSI, 2010).IntroductionPump performance data (Visintainer and Whitlock, 2012) has been collected for a froth pump using an experimental loop outfitted with an array of pressure transducers, mass flow meters, an inverted U-loop, magnetic flow meter and an assortment of other instrumentation. Experiments were performed on pure water, water and air, pure corn syrup, and corn syrup and air. Data was obtained for % air contents of 0-30% and viscosities of 1- 15,000 cSt at eight specific valve positions (eight different flows as a percentage of best efficiency flow points) and the viscosity was changed by allowing the system temperature to increase during testing. The test pump is a 710-mm diameter impeller, GIW HVF, open shrouded, vented design that has its discharge axis oriented at 45° upward from the horizontal. A schematic diagram of the froth pump test loop can be seen in Fig. 1."

Jan 1, 2015

By Yuemin Zhao, Daniel Tao, Rick Honaker, Maoming Fan

"Froth flotation is the most widely used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubbles on the flotation performance of different particle size fractions of coal was investigated using a bank of 10-L flotation cells, a specially designed 50-mm inside diameter column and a 152-mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during the froth flotation process improved flotation efficiency. The use of nanobubbles in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.IntroductionFor minus 0.6 mm fine coal or minus 0.15 mm ultrafine coal particles, froth flotation is known to be the most efficient and the most cost-effective separation technique. However, flotation efficiency decreases sharply with ultrafine and relatively coarse coal particles. Studies have shown that the low flotation efficiency of ultrafine particles is mainly due to the low probability of bubble-particle collision (Yoon et al., 1989; Ralston and Dukhin, 1999). Enhanced flotation of fine and ultrafine coal can be achieved by increasing collision and attachment probabilities.The top size of particles that can be recovered by flotation depends on the combination of mineral properties and flotation devices. Turbulence in flotation devices is an important factor that affects the stability of bubble-particle aggregates. Even in the flotation of fine particles, bubble-particle detachment can significantly influence the kinetics of flotation taking place in mechanical cells, which provide intensive turbulent agitation (Deglon et al., 1999). Coarse particle flotation is more difficult, because increased agitation is required to maintain particles in suspension and coarse particles are more likely to detach under turbulent conditions (Mankosa and Kohmuench, 2002; Soto and Barbery, 1991). More efficient attachment of particles and improved flotation rate has been observed when tiny bubbles coexist with conventional-sized flotation bubbles (Attalla et al., 2000; Tao et al., 2010; Fan et al., 2010a, b, c, d; Fan et al., 2012)."

Jan 1, 2015

By Steve Trussell, William H. Langer

"Arizona aggregate (sand, gravel and crushed stone) producers enjoyed more than a half a century of nearly constant growth in demand for aggregates. Approximately 80 percent of the aggregate produced in Arizona is sand and gravel, and 20 percent is crushed stone (U.S. Geological Survey, 2015). Figure 1 shows the generalized distribution of potential sources of sand and gravel (yellow) and potential sources of crushed stone (other colors described below). Black dots show locations of aggregate operations.Sand and gravel commonly is produced from modern river channels and terraces although some alluvial fans and high-level paleo-river terraces also serve as aggregate resources. The gravel clasts are a mix of rock types that reflect the types of rock in the source area of the rivers. Generally processed river gravels meet stringent specifications for highend uses.Crushed stone, which makes up about 20 percent of production, primarily comes from a variety of metamorphic rocks and light-colored intrusive igneous rocks such as granite (brown areas), dark colored extrusive igneous rocks such as basalt and scoria (rust colored areas), and carbonate rocks such as limestone or dolostone (green areas). Carbonate rocks are also used in the manufacture of cement and lime.Construction and aggregate production in ArizonaBecause aggregate producers have limited facilities for storing product, stockpile changes are insignificant compared to production. Therefore, demand or consumption of aggregate in Arizona is considered to be equal to production. Production figures used in this paper reflect shipments, sales or marketable production, including aggregate used by producers to make readymix concrete and asphalt. Production figures were reported by the U.S. Bureau of Mines from 1950 until 1995 and by the U.S. Geological Survey (USGS) since then. Production figures are reported voluntarily, and major operators are the primary source for these figures. Because many smaller operators do not report their production, the figures are conservative values that provide an approximation of aggregates production activity."

Jan 1, 2015

By Eric Lutz

"Great effort has been expended for more than 40 years to improve the workplace safety and health of surface and underground miners across the United States. When looking at the past decade, withstanding the 2010, Upper Big Branch (UBB) disaster that took the lives of 29 miners, this effort has resulted in a generally decreasing trend from 57 fatalities (22 coal; 35 metal/non-metal) in 2005, to 45 (16 coal; 29 m/ nm) in 2014. Through August of this year, there have been 23 mining-related deaths (eight coal; 15 m/nm). These results reflect continued diligence and perseverance on the part of miners that stay true to our legacy; and demonstrate significant investments from mine-site leadership, mining corporations, and state and federal regulators. However, over the past five years there have been an average of 32 fatalities per year, with a low of 36 (2011 and 2012) to a high of 45 (2014). If we know that there will be somewhere between 30 and 50 mining related deaths next year, which of us will volunteer to be counted as one of the numbered? Clearly, we all agree that one fatality is too many; and as evidenced by changes following UBB, deaths in any sector are deaths reflective of all mining across all sectors.The impact of each miner death touches us all. Miner’s deaths are felt deeply by family and friends, most significantly the children; their communities in which they served, supported, and worshiped; and by society that has lost a hardworking, dependable contributor. Further, to take a slightly cynical, but realistic view, miner fatality events impact the financial vitality of mining and contracting companies and broadly diminish investor confidence. Just as important, these events significantly impact our communities and result in negative public perceptions, which ultimately drive regulatory policy and related compliance pressures. This resulting pressure forces operations to broadly address safety and health gaps in very specific ways (i.e., see U.S. Mine Safety and Health Administration (MSHA) regulations regarding lids for trash cans) minimizing a mine site’s opportunities for operational flexibility. To break this cycle that is the operational reality, mining companies are focusing tremendous efforts on fatality prevention and specifically on dedicated investment to prevent multiple fatality events."

Jan 1, 2015

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015