Search Documents

By Roland Trunk, Marcel Imbach, Yves Boissonnas, Jan Vesely

"INTRODUCTION The expansion of the Suez Canal, which runs between the Mediterranean and Red Sea, is at the top of Egypt’s economic agenda. The £8 billion development plan includes a new channel alongside the existing one which will double the number of ships able to pass each day and several tunnels to connect the Sinai peninsula to the main part of Egypt. The Egyptian government ordered three new tunnels under the Suez Canal in the area of Port Said as part of the Canal Region Development Plan. The three tunnels will contribute to the North Sinai expansion, helping to create a vast industrial zone and completing the coastal road extension from Rafah to Nuewiba. Two of these three tunnels will be allocated for roads and the third for railway traffic. A further part of the Suez Canal development mega project are an additional six tunnels in the area of Ismailia and Suez. The focus of this paper is on the two road tunnels in Port Said and will give an overview of the project and the challenges encountered regarding the technical complexity and tight time schedule both in its design and execution. PROJECT OVERVIEW The tunnels will be built in the area of Port Said (see Figure 1) which is the most northern part of the Suez Canal.The road alignment connects the Port Fuad Road in the east bank of the Suez Canal to the Port Said-Ismailia highway in the west bank with a dual carriageway section. Each of the carriageways has two lanes. The bored diameter of the 2.8 km long road tunnels is 13.050 m and will be driven with two Mix-Shield TBMs. The distance between the two tunnel axes is planned with 42.5 m (discussion about a reduction are ongoing). The width of the Suez Canal is around 340 m at upper level and around 170 m at the bottom. During the TBM drive, three main geological layers are expected. Below a depth of around 40 m in a very soft clay layer, a dense to silty sand layer is predicted. Within the sand layer another silty hard clay is expected in different depths with variable thickness. After finishing the excavation of the road tunnels, the same TBM will be used for the railway tunnel. The lowest points of the road tunnels will be located 59 m below the surface (tunnel invert to surface) and only 18 m of ground cover exists between the tunnel crown and the Suez Canal invert. Minimum ground cover over the tunnel crown is approximately nine meters at the tunnel portals."

Jan 1, 2016

By Olivia Perkins, Shawn Sismondi, Adrian St. John, Vicky Potts

"INTRODUCTION An inherent aspect of any tunnelling project is ground risk: how it is identified, quantified and managed throughout the various stages of a project. Early identification of these risks, such as adverse ground conditions or potential obstructions is crucial; however specific identification of all risks will inevitably be limited by the extent of the desk study, ground investigation and accuracy of as-built information available, particularly in a densely populated urban environment such as London with a long and varied history of development. It is therefore crucial to have suitable plans and procedures in place for dealing with potential ground risk scenarios if they occur during construction work to ensure the safety of the workforce and to protect nearby critical assets. A number of experiences of potential ground risk were encountered during the Sprayed Concrete Lining (SCL) works on Crossrail contract C300/410 which was constructed by a joint venture of BAM Ferrovial Kier (BFK). The C300/410 works, undertaken in the heart of London, comprised of over 2.5km of SCL tunnels for Bond Street and Tottenham Court Road Stations and the Fisher Street crossover, as well as two 6.2km TBM tunnel drives between Royal Oak and Farringdon. BFK appointed Donaldson Associates as their SCL designers for the works; together they were responsible for excavation stability up to the point of ring closure. Despite the majority of SCL tunnelling works at Bond Street and Tottenham Court Road being through the favourable medium of London clay, there remained areas of local geotechnical challenges. Some of these were expected from the outset, some became apparent as works progressed from records of other nearby excavation works, and some were only encountered during tunnel excavation. Being located in the centre of London meant that there always remained a possibility of meeting some form of obstruction from previous structures. However, identification of all potential issues prior to the commencement of the works was challenging and proved to not be entirely possible. Through a series of case studies, this paper documents incidents where obstructions or adverse ground conditions arose. These scenarios all had the potential to cause safety risks, impact the tunnel design and/or construction methods and ultimately add time and cost to the works. The paper discusses how these challenges were overcome which utilised in part, a progressive risk reduction cycle, feeding back knowledge gained at all stages of construction into the approach for undertaking the works. It also examines what could be done in future to further reduce the ground risk through early identification, communication, education and appropriate contingency measures."

Jan 1, 2016

By Ulrich Maidl, Gustavo Aguiar, Argemiro Ferreira, Marco A. Peixoto Silva, Marc Comulada

"Metro Line 5 in Sao Paulo is being constructed. This lot extends for 4,940 m with twin EPB shield tunnels under a dense and busy urban area, with an excavation diameter of 6.9 m. The tunnels run predominantly in the tertiary soils of Sao Paulo where extensive experience exists from previous EPB shield tunnel projects. However, new experience is being gained in Sao Paulo in shield tunnelling through Saprolite, the weathered product of the underlying Gneiss crystalline basement, through the resulting residual soils and in rock-soil mixed face conditions. Furthermore, experiences in difficult mixed face soil conditions with overconsolidated clay at the face in combination with loose sands at the crown under the groundwater table will be presented. Additionally, the design, operational and controlling approach followed for the shield drive at particular critical cross-sections where the shields were driven close or under buildings. INTRODUCTION Within the framework of Sao Paulo´s metro network expansion, the excavation of the shield tunnels for Metro Sao Paulo Line 5 is currently taking place. The present paper deals with the description of the most relevant features from the construction of the Line 5 – Lot 3 tunnels. The paper presents how particular challenges were dealt maximising potential of EPB shield tunnelling technology. Challenges were posed not only by the difficult boundary conditions of urban shield tunnelling, such as shield drive under buildings, but also by complex geotechnical situations. PROJECT DESCRIPTION The great urban area of São Paulo is one of the biggest cities in the world, with around 20 Million people living in the city and in the suburb area. The city faces great mobility problems and in the last years the government has been investing great amounts on the megacity´s metro expansion. The Line 5 Extension plays an important role to connect the south area to the central area of the city, with a whole extension of 11 kilometres, including 11 new stations. It is estimated that this line will transport almost 900.000 passengers/day. The first stretch of the expansion, Lot 3, consists of two single tunnels, almost 5 kilometres long each, crossing 4 stations. Figure 1 shows details of the Line 5 Expansion."

Jan 1, 2016

By Salam Moubarak, Thomas Camus

"INTRODUCTION Since the introduction, several decades ago, of the first concepts of tunnel boring machines (TBMs), the unremitting increase of mechanized and automated tasks and the reduction of manual tasks carried out by human operators have gone hand in hand with the continuous improvement of these machines. In the present state of TBMs, the replacement of worn cutting tools is a critical, tedious, and dangerous manual operation especially for earth pressure balanced (EPB) and slurry TBMs. For such pressurized TBMs, hyperbaric interventions are used. They consist in replacing the pressurized soil/mud inside the chamber with compressed air that balances the face pressure. The operators can then ""dive"" into the chamber; however, because the human body cannot naturally undergo pressure changes, they have to follow strict procedures that have been developed for subsea divers, based on decompression stops. Indeed such interventions are actually quite often performed by professional deep-sea divers. The pressurized TBMS are consequently equipped with a manlock that allows for the required compression and decompression cycles. Hyperbaric interventions increase risk to the operators and require long decompression procedures that increase the TBM idle time and reduce its efficiency. At higher pressures, over 3.5 bar (ITA Report No 10, 2011), specific equipment and special gas mixes and/or saturation techniques are recommended (Lamont, 2012). Such procedures are even more expensive and time consuming although the duration of work in the pressurized area can be very limited for health and safety reasons. Contractors are therefore increasingly interested in automating these operations to reduce the risks to human workers and improve the TBMs performance. Moreover, the demand for new, ambitious and challenging tunneling projects (very deep, high pressure boring) is ever increasing, but the supply of suitable TBMs is limited and the risk from working in the hyperbaric environments becomes increasingly unacceptable. Impact of hyperbaric interventions The UK Health & Safety Executive has analyzed the consequences of working in intermediate pressure compressed air. The retrospective study of decompression illness (DCI) indicated that at certain pressures its incidence was around 2% of all exposures. More worryingly it showed that over 20% of the exposures commonly undertaken by shift workers in tunneling (those over 1 bar pressure for 4 hours or more) resulted in DCI. It was concluded that on some contracts up to 50% of shift production workers experienced DCI at some time during the contract, a situation which was considered to be wholly unacceptable (Lamont, 2006)."

Jan 1, 2016

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

"Hecla Limited has been investigating the potential benefits of using a Spendrup/Compact Filter Technic (CFT) diesel filtration system to remove diesel particulate matter (DPM) from the mine atmosphere to optimize use of the available air. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the scrubber efficiency for dust and DPM which is to be presented in another report. This paper reports on a new mining application of a carbon particulate sensor’s ability to continuously monitor long-term mine DPM levels in conjunction with the scrubber evaluation. Magee Scientific is the manufacturer of the Aethalometer®, a continuous black carbon monitor which has been used extensively in worldwide ambient air quality monitoring networks. Two Aethalometers were used at the mine to assess their potential to continuously track underground DPM levels. In this first underground mine application, the Aethalometers were used to continually monitor black carbon (BC) in the intake and exhaust of the CFT scrubber system. Results showed that an off-the-shelf Model AE33 Aethalometer could continually track underground BC levels for extended periods of time over the course of the six-week trial. Data at the scrubber intake over 14 days of testing showed that DPM filtration would be required less than half of the time to maintain BC levels below 50 µg/m3. If the Aethalometer BC data output were “smart coupled” to control a 200-HP in-mine scrubber, significant electrical cost savings would be realized. INTRODUCTION Mine ventilation airflow quantities are calculated to maintain a safe and healthy environment for miners. Dilution of diesel particulate matter (DPM) is often a key factor used to determine the required quantities of ventilation air (Bugarski et al. 2011). DPM emissions and exposure levels are highly variable depending on mine schedules and activities (Janisko & Noll 2010); however, lacking technology to continuously monitor levels, mine ventilation systems are often over-designed in order to handle worst-case scenarios to ensure that DPM levels are maintained at or below regulatory limits. As mines go deeper it becomes more difficult to supply air, and the development of new shafts for air is not economically feasible (Basu et al. 2008). Cleaning and reuse of available air then becomes an attractive option to maintain good air quality."

Jan 1, 2016

By Vincent Tricot, Daniel Altier, Roger Storry

"INTRODUCTION The Liantang / Heung Yuen Wai Boundary Control Point (BCP) project, located in the north-east New Territories of Hong Kong, will form the seventh land crossing between the Hong Kong Special Administrative Region (HK) and Shenzhen in China (Figure 1). The BCP project comprises an 11km long dual two-lane trunk road linking the border crossing facility to the existing road infrastructure in HK and when completed it will facilitate future regional development and alleviate frequent traffic congestion at the existing Boarder control points.In December 2013 Dragages Hong Kong (a member of the Bouygues Construction Group) was awarded the 5.4km long Contract 2 section of the project, including the 4.8km long Lung Shan Tunnels, by the Civil Engineering and Development Department of the Government of the HK SAR. To overcome the difficult ground conditions anticipated along the Contract 2 section of the project the tunnels will be constructed using mechanical and drill and blast (D&B) excavation techniques together with a 14.1m diameter multi-mode Earth Pressure Balance Tunnel Boring Machine (TBM). Land constraints imposed on the project alignment require that the final 500m section at the northern end of the Lung Shan tunnels, under Princess Hill (Figure 2), takes an almost 90 degree turn towards the north. The resulting 354m radius curve restricts the sight-line of road users to below the minimum 110m at 80km/hr hence, the internal span of the tunnels needs to be increased from 12.6m, in the standard straight section, to 15.4m in this curved section to accommodate a widened shoulder which will provide the required sight-line distance."

Jan 1, 2016

By S. Amirshenava, S. Nadimi

"Premature and unplanned mine closure can result in significant adverse impacts on the environment and community and need to be managed appropriately. Risk management techniques can reduce the negative impacts and risks of early mine closure. Risk Assessment 3D Model, is an efficient tool to quantify risk. The aim of this paper is to identify the mine closure risks in Choghart iron ore mine, and calculate the overall mine closure risk level. The result shows that 51.4% of assessed risks have low risk level and the overall risk level of early mine closure is low. Keywords: mine closure, risk assessment 3D model, Choghart iron ore mine INTRODUCTION The modern mining life-cycle can be divided into three main stages; exploration, mining (opening and production) and post mining (mine closure, and reclamation). Mine closure is the critical component of the modern mining life-cycle and it refers to the period of time when the operational stage of a mine has permanently ceases (Heikkinen et al, 2008). Planned closure occurs due to the depletion of ore reserves, but sometimes it is premature. Laurance (2006) shows that only 25% of mine closure in the past 30 years was due to resource depletion and in 75% of the cases the mines were closed for the other reasons. Ghanbari et al (2010) demonstrated that 48.6 % of copper mine closure in the past 100 years was due to resource depletion and 51.4 % of copper mines have been closed due to other reasons. The main reasons of premature mine closure are as follow (Laurance, 2006; Ghanbari et al, 2010; Maiti, 2013): • Economic, (low commodity prices or high costs) • Geological, (over-estimation of grade and tonnage) • Geotechnical (adverse geotechnical conditions) • Technical (equipment failure) • Regulatory, due to safety or environmental breaches • Social or community pressures • Closure of downstream industry or markets • Flooding or inrush Minaei Mobtaker and Osanloo (2013) developed a mine closure prediction model based on the data collected from closed iron ore mines in the past 100 years. They showed that economic factors, exhaustion of ore reserve and geological conditions are the main reasons of iron ore mine closure. They treated mine closure as a decision making problem in order to predict the causes of mine closure, including the uncertainties of some mine plan parameter such as iron ore price, production and consumption."

Jan 1, 2016

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By J. C. Stankus, R. Ochsner, B. Hanson

"Bull Mountains No. 1 mine of Signal Peak Energy made another success in its 4 Right pre-developed recovery entry on March 23 and 24, 2015, after the first successful cut-through and shield retrieval of 3 Right pre-developed longwall recovery entry in 2014[1]. Under the same geological conditions, the major difference of 4 Right and 3 Right is the 600 psi Unconfined Compressive Strength (UCS) value of light-weight concrete in 4 Right versus 800 psi in 3 Right. In addition, one more recovery chute was added in 4 Right. The unique geological conditions in this mine include: (1) the low overburden of approximately 200-260 ft, (2) prevalence of roof joints parallel to the face in the sandstone/siltstone dominated overburden, (3) proximity of the Rehder rider seam to the bench Mammoth coal seam, and (4) prompt surface subsidence with the face advancement. The 4 Right recovery entry was 42 ft wide and developed in two stages, 20 ft wide in the inby Phase I, and 22 ft wide in the outby Phase II. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, primary bolts, and high-capacity supplemental SUMO cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. It took approximately half time to easily cut through the concrete with less dust in 4 Right as compared to the concrete-cut-through time in the 3 Right. The updated study further explored the nature and mechanism of effective roof control approaches in the pre-developed recovery entry of this unique geology mine, aiming at providing the safest working environment for protecting the miners. GEOLOGICAL AND MINING CONDITIONS OF THE RECOVERY ENTRIES Bull Mountains No. 1 mine is located 30 miles north of Billings, Montana, and currently mines bituminous coal from the Mammoth coal seam. The mine employed a conventional recovery face in Panel #1 and pre-developed recovery entries in Panels #2, #3, and #4 (Figure 1). The typical mining and geological conditions are as follows:Overburden Depth The overburden above the Mammoth coal seam in the #1-#4 Right recovery areas is approximately 200-260 ft. This low cover, in combination with specific roof geological features (especially the prevalent roof joints and proximity of rider seam), constitute unique ground movement characteristics when the longwall face advances into the recovery entry if no sufficient roof support is installed."

Jan 1, 2016

By Günther M. Volkmann

"INTRODUCTION The construction of the BAB 44 motorway between Kassel and Herleshausen (both Germany) is an important part of the trans-European road network. After its completion, the A 44 will permit an efficient connection of the Benelux States in the West and Poland in the East. In the section between Eschenstruth and Hessisch Lichtenau the Hirschhagen Tunnel is constructed with a length of 4.1km. Most sections of the tunnel are situated in weak ground conditions. Hence a combination of face bolts with spiles (short forepoling) or pipe umbrellas (long forepoling) additionally support the tunnel heading on a regular basis This article will focus on the application of a newly developed method to connect the pipe umbrella support, which is mostly installed by conventional drilling machines nowadays. The installation method limits the outer diameter to a maximum of 168mm and a pipe wall thickness of 12.5mm because workers must be able to handle pipes and its drill steel. Typically these pipes are connected with threads that create a weak link in the support system so during the last decade alternative connection systems were developed to overcome this disadvantage. One of these alternative coupling systems is the so called Squeezed Connection, which will be explained in this article followed by a discussion of its advantages and disadvantages regarding technical specifications, construction time, and safety issues. THE HIRSCHHAGEN HIGHWAY TUNNEL The German highway A 44 directs from Aachen through the Ruhrgebiet to Kassel (all Germany) and it is extended to Herleshausen (Germany). The new section connects the A 7 to the A 4 after completion. This upgrades the east-west highway connection starting at the Benelux Union and heading to Poland so it is an important part of the trans-European road network. The newly constructed section has a total length of approximately 63 km and comprises 13 tunnels. All tunnels are constructed as double tube tunnels with 2 lanes and emergency sidewalks on both sides and 14 emergency cross passages. The Tunnel Hirschhagen starts in the north of Eschenstruth and ends near Hessisch Lichtenau (Figure 1). The length of the northern tube is 4,147 m and that one of the southern tube is 4,204 m. So it is the longest tunnel of the A 44 and the second longest highway tunnel in Germany when it is put into operation. On its alignment it crosses underground the Losse valley with the state road 7, the streetcar Kassel-Hessisch Lichtenau and the Losse stream. The cover above crown varies from 10 m to 95m and it is the lowest when crossing the Losse stream."

Jan 1, 2016

By Matthias Neuenschwander, Andreas Theiler, Patrick Steinle, John Singer, Martin Vogel, Diego Martini, Ömer Ündül, Markus Weh

"Quartz Dust is a major health hazard in underground works, wherever the ground contains quartz and depending on the chosen method of excavation. A research project initiated by the Swiss Tunnelling Society and realized by the Swiss Federal Institut of Technology, Zurich, established a correlation between the potential of quartz dust generation during excavation and well known geotechnical characteristics – the Cerchar Abrasivity Index CAI and the Uniaxial Compressive Strength UCS - of ten typical Swiss rocks. The results are at the center of a new guideline by the Swiss Society of Engineers and Architects on the requirements for early project stages regarding ventilation and logistics in function of the quartz dust related risk of the expected ground type of the project. The approach presented could be applied worldwide, contributing to more effective health protection as well as to better cost stability in underground works. CONTEXT Respirable quartz dust (aerodynamic diameter of particles < 10 micron) is universally recognized as a major workplace health hazard. Chronic bronchitis, silicosis and lung cancer can be caused by excessive exposure to quartz dust, as has been proved by many medical studies. Therefore, the legislations of many nations specify a maximum workplace concentration (Maximale Arbeitsplatzkonzentration MAK, Occupational Exposure Level OEL). In Switzerland, for example, the Threshold Limit Value TLV for respirable Quartz or Crystalline Silica imposed by the Federal Committee on Exposure Levels (Grenzwertkommission) is 0.15mg/m3 air. Some nations refrain from establishing a OEL because of the carcinogenic nature of quartz."

Jan 1, 2016

By Patrick Oriez, Chris Norris, Alain Mercusot

"Temporary mechanical ventilation is one of the fundamental requirements in guaranteeing a healthy atmosphere in underground construction works in order to protect the health of persons working on the site. It is therefore essential to conceive a system which meets the requirements of the whole of the worksite and for all phases of work which takes into account all aspects pertaining to its design, dimensioning, justification, installation, maintenance and validation. In doing so, the ventilation design and the selected apparatus to be installed shall meet with the degree of health protection and the quality of air of the worksite as defined by the legislation in force in France, through limiting the concentration of the different pollutants associated with the site activities. Consequently, when presenting a mechanical ventilation project, all of the participating parties and especially the contractor make a commitment to guarantee sufficient volumes (or airflow rates) of fresh (non-polluted and oxygenated) air and extracted (polluted) air in order to meet these limitations and maintain them in all conceivable site configurations. This article sets out the most important aspects of the implementation of a ventilation project from the initial design stage through to its application, discussing French legislation, ventilation principles, calculations and techniques with regards to underground construction sites. BASICS OF VENTILATION Mechanical ventilation studies are concerned with all of the site workstations and work phases which are sources of pollution and apply to all zones of the underground worksite with the goal of maintaining the concentration or composition of this pollution below the permitted levels and comply with the following three basic principles which are complementary to one another without being in contradiction. •,The first principle consists in eliminating or limiting as much as possible the emission of any polluting, irritant, or dangerous substances, by specifying appropriate construction techniques and equipment (use of electric motors, combustion engine equipment: filters, tanks, catalyzers, use of less polluting explosives, damping down dust with water or wetting products, damping down and diluting certain gases using water mists). •,The second principle is designed to capture residual polluting substances emitted close to the source in order to prevent them from spreading into the worksite atmosphere (extraction ventilation with ducting up to the source – upstream of the extractor fan – and use of downstream filters before expelling the polluted air to the exterior). •,The third principle involves accompanying the capture of the pollutants with additional blowing ventilation specific treatment of substances dissipated by and distant from the source of pollution (acceleration of the drift air flow in order to confine dust and better capture it, supply ventilation with ducting in order to dilute the gases emitted and discharge them to the exterior)."

Jan 1, 2016

By Mohamed Gamal, Bill Zietlow

"In oil fields that have been depleted with conventional surface oil wells but still contain significant reserves, an extraction alternative that has been constructed recently consists of a drilling gallery below the oil-bearing formation at the bottom of a 1,200-ft deep shaft where upward sloping wells are being drilled to allow oil collection by gravity. The gallery is 92-ft diameter with a flat ceiling supported by rock bolts and shotcrete structurally connected to the shaft liner, which doubles as a large tension support element. A special excavation sequence was implemented for the gallery to maximize arching in the stress above the large diameter gallery. The gallery was located in competent sandstone, constructed with sequential excavation methods, and designed with a 3D finite element model. Special consideration was given to optimizing the gallery location to take advantage of the geology for construction and support while giving good positioning to the well drilling equipment. BACKGROUND Brierley Associates was contracted to provide both design and construction management services for an approximately 1,165-ft deep, 18-ft excavated diameter vertical shaft that opens to a 92-ft diameter flat roof gallery. The geotechnical data for the site was based on information available from literature and from data obtained during core drilling and from in-situ testing in a 1250-ft deep borehole. Wire line coring was conducted using a HQ, 10-ft long core barrel with a mud-rotary drilling method through sedimentary bedrock. The geometry of the shaft and the bottom gallery is shown in Figure 1(a). GEOLOGIC SETTING AND STRUCTURAL GEOLOGY The stratigraphy at the site includes a series of interbedded marine limestone, shale, claystone, siltstone, sandstone, and chert units. Limestone and shale are the predominant lithologies in the upper approximately 675 ft, while the lower portion contains five distinct sandstone units and more abundant shale, claystone, siltstone, and coal than the upper zone. A cherty sandstone at a depth of 1,130 below ground surface (bgs) was encountered. At a depth of about 1,000 ft to 1,116 ft bgs, a non-marine sandstone unit was encountered. This sandstone is the hydrocarbon bearing layer. Joints and fractures observed in the limestone had dips ranging from 0 to 90 deg. from horizontal with joint and fracture surfaces that ranged from planar to irregular and smooth to rough. Several, near vertical shear planes with slickensides were observed with surfaces that were generally smooth and planar. RQD values for the limestone ranged from 0 to 100 percent but in general were good to excellent."

Jan 1, 2016

By Alfredo Valdivia, Hamed Nejad, Vincent Monaco, William Cao

"The East Side Access (ESA) CM005 Contract - Manhattan South Structures - consists of the installation of the waterproofing and final concrete lining for railroad tunnels, 3-Level Wye track turnout structures, segments of the Main Cavern Station, and a series of Ventilation Structures excavated beneath the existing Metro North Railroad (MNR) Grand Central Terminal. Several key team decisions made collectively by the Construction Manager (CM), Designer, and the Contractor has allowed the scheduled construction duration of 29 months to be maintained. These strategies include the use of alternate design and construction methods, including the use of pneumatically applied concrete lining and precast lining. This paper discusses these strategies, and illustrates how successful teamwork and cooperation during the execution of a large-scale construction project can lead to lowering costs, improving quality, and maintaining the overall project schedule. INTRODUCTION The East Side Access Project The Long Island Railroad (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already over congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodate the NJ Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the NYCT Subway System and Metro North Rail Road. The ESA Project includes building new tunnels and facilities under Manhattan and Queens. (See Figure 1).The Manhattan Alignment In the Manhattan segment of the ESA Project the excavation in hard rock of tunnels, cross passages, caverns and shafts has been completed by tunnel boring machines, drill and blast, and road header. The construction of the structural concrete final lining, interior structures and fit-out of the previously excavated caverns and tunnels are currently being performed under Contract CM005 Manhattan South Structures awarded to Michels Corporation and Contract CM006 Manhattan North Structures awarded to Frontier Kemper Constructors Inc. This paper focuses on the design and construction aspects of Contract CM005 which is the first ESA Contract in Manhattan to successfully construct concrete final linings in pre-existing excavated areas."

Jan 1, 2016

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By Basar Arioglu, Jaeung Kim, Mehmet Öztürk, Jinmoo Lee, Dongho Lee, Taek-Kon Kim

"Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) includes 3.34 km of a bored double-deck tunnel under the Bosphorus Strait, at a maximum depth of 106 m from the sea level, and 1 km of twin NATM tunnels on the Asian side. The region’s variable geology, hydrology and propensity for seismic activity, combined with high water pressure and large-diameter/double-deck tunnel configuration, make the Eurasia Tunnel one of today’s most challenging and complex projects under construction. Due to the site’s proximity to the active North Anatolian Fault, the tunnel is designed to withstand a 7.5 magnitude earthquake. The tunnel penetrates through both the Trakya bedrock (on both European and Asian sides) and the alluvial sediments at the bottom of the channel. The tunnel is designed to accommodate differential displacements by introducing seismic/flexible joints at proper locations at the transition zones between rock and soft soils. Tunnel fire is also a significant design consideration for undersea tunnel due to that the rubber protecting it in close proximity of the seismic joint should resist a fire for long term safety and durability. This paper mainly focuses on the design for method of tunnel response analysis in transverse and longitudinal direction against seismic demands relating with the seismic joints. INTRODUCTION Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) will build and operate a roadway tunnel under the Borphorus connecting Kazlicesme on the European side and Goztepe on the Asian side, to provide additional road-access across the Strait and consist of three main parts as shown in Figure 1."

Jan 1, 2016

By William W. Edgerton, Moussa Wone, David H. Corkum, Carlton M. Ray

"The DC Clean Rivers (DCCR) Project is a 25 year, $2.6 Billion court ordered project to reduce combined sewer overflows (CSOs) discharging into the Potomac and Anacostia Rivers and Rock Creek, and also reduce flooding in the northern areas of the District of Columbia. Like all massive infrastructure programs, DCCR faced technical challenges, management challenges, risks of cost and schedule overruns, procurement challenges, and financing challenges. While DC Water is no stranger to large capital improvement projects (CIP), this CSO Program represents a once in a lifetime event for the Owner requiring the assembly of a single purpose team to implement. Some of the DCCR Project team’s most successful accomplishments to date are attributable to its introduction of early contractor involvement (ECI) to thoroughly vet the work from the perspective of the future constructors, development of functional baselines to share risks that are difficult to price and reduce reliance on geotechnical baseline interpretation during tunnel excavation, and attainment of financing through Municipal Century Green Bonds based on using design criteria of a minimum of 100 year life for the structures to establish intergenerational equity and fairness. This paper will discuss these innovations in detail and provide some sets of recommendations for the underground industry on when and how to use different approaches to better manage projects of this magnitude. INTRODUCTION The District of Columbia Water and Sewer Authority (DC Water) is an independent multi-jurisdictional authority that was established in 1996. Its primary mission is to provide water distribution services to more than 640,000 residents in the District of Columbia (District), and sewer treatment and disposal to 1.6 million residents of the District, Montgomery and Prince George’s counties in Maryland and Fairfax and Loudoun counties in Virginia."

Jan 1, 2016

By Scott Lewis, Andrew Kositsky

"INTRODUCTIONThe South Napa Earthquake of 2014 caused ground motion at numerous reinforced concrete-lined (shotcrete-lined) winery tunnels in Napa County and Sonoma County, California. The occurrence of seismic ground motion at these tunnel complexes, known as wine caves, presented an opportunity to reevaluate seismic performance of reinforced concrete and reinforced shotcrete lined tunnels. The authors of this paper updated the most recent comprehensive compilation and evaluation of case studies by Power and others (1998), which correlates peak ground acceleration (PGA) at tunnel sites to damage. For this update, the authors evaluated the seismic performance of 31 wine caves near the South Napa Earthquake epicenter; including some of the 90 wine caves they designed since 1991, some caves designed by others, and additional caves constructed by contractors that they frequently work with. Tunnel designers can use the new data presented in this paper to help evaluate the usefulness of detailed seismic design analyses. THE SOUTH NAPA EARTHQUAKE The South Napa Earthquake occurred at 3:20 AM Pacific Daylight Time on August 24, 2014. Figure 1 shows the approximate location of the epicenter, the measured/estimated PGA contours, and the location of wineries with wine caves added to the database where the PGA was at least 0.2 g. The epicenter was along the West Napa fault, about 5 miles south-southwest of downtown Napa, California. The earthquake moment magnitude was 6.0, and measured/estimated PGAs were up to about 0.7 g. The duration of strong shaking was about 10 seconds. This earthquake was characterized by right lateral strike-slip fault movement, ground surface rupture, and after slip at the ruptures. Increased surface water flows were observed at seven creeks after the earthquake. Groundwater level rises of up to 5 feet were observed in Sonoma County wells after the earthquake. The earthquake was the largest seismic event in the San Francisco Bay Area, which includes Napa and Sonoma Counties, since the 1989 Loma Prieta Earthquake. The Napa event caused an estimated $400 million in damage. This damage included moderate to extensive structural damage to older commercial buildings and to some newer buildings in downtown Napa. This damage resulted from ground motions, subsequent fires, and failed underground utility systems."

Jan 1, 2016