Search Documents

By K. M. Mohamed, I. B. Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to reduce rib fall accidents and fatalities in underground coal mines. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified. The paper presents a coal rib model to simulate the mechanism of the coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff mine in Australia. Fracturing of the coal rib was defined by critical values of shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data. INTRODUCTION Coal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities [1]. Despite the threat of rib falls, the amount of rib falls and rib support research conducted in the U.S. is limited compared with what has been done in pillar and roof support design. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to minimize the number of rib fall accidents and fatalities in underground coal mines."

Jan 1, 2016

By Apostolos Vrakas, Georgios Anagnostou

"INTRODUCTION The small strain assumption routinely made in tunnel analyses remains sufficient from an engineering point of view as long as convergences do not exceed 10%. More specifically, small strain theory assumes that deformations are so small (in relation to the size of the underground opening) that any geometric change in the continuum can be disregarded (Fig. 1a). In fact, however, the geometry is updated during loading (or unloading) according to large strain theory and thus equilibrium and stiffness are evaluated on the deformed configuration of the continuum (Fig. 1b).In problems involving large deformations, where the undeformed and the deformed tunnel geometry differ significantly, small strain theory leads to erroneous and sometimes even nonsensical results (i.e. it can predict wall displacements even greater than the excavated radius under conditions of very low stiffness and strength, high in situ stress and low support pressure). This can easily be verified from the widely applied relationships for the ground response curve. For example, in the ideal case of linearly elastic behaviour, the convergence of an unsupported opening equals (1+?) s0 / E (where E, ? and s0 denote the Young’s modulus, Poisson’s ratio and initial isotropic stress, respectively) and is greater than 100% for E < (1+?) s0. Although convergences are less than 10% in the great majority of tunnelling projects, very large deformations may take place when tunnelling through weak rocks under a high overburden (Fig. 2). This paper will first present a very simple and practicable way to account for large strains, based entirely on the results of routine small strain analyses, and will subsequently show the importance of addressing large strains in tunnel analysis and design with reference to three typical case studies of tunnelling in squeezing ground."

Jan 1, 2016

By D. Kruse, M. Sanaei

"A three dimensional nonlinear finite element model was constructed to simulate and analyze the behavior of large diameter segmentally lined shafts when subjected to seismic waves. To reduce computation time, a less complex shell model was also constructed. Transient excitation was applied to the supported nodes of both models, at the base of the shaft, with a time-function representing the 1994 Northridge earthquake. The models are developed at the end of an original phased construction-stage analysis of the shaft. Displacements, forces and moments are monitored and compared during the analyses steps. During the initial 15 seconds of the earthquake, the top and bottom of the shaft show similar displacements. The maximum horizontal displacement within the shaft is approximately 3.5 inches in the solid model and the shell model results conform to this by a factor of 50%. Keywords: Segmentally Lined Shaft, Soil Structure Interaction, Seismic Analysis, Finite Element Modeling, Ground Modification INTRODUCTION TO SEGMENTALLY LINED SHAFTS Large diameter segmentally lined shafts (SLS) are underground systems, constructed sequentially using precast concrete segments to form a ring which provides both temporary earth support during excavation and permanent structural support. The segments are connected via alignment pins, bolts, packer material and other structural components that ensure the continuity of the SLS. In this analysis, the construction process uses a top-down sequence wherein each soil layer is excavated, damp-proofing is installed and concrete segments are assembled to form each ring. This process is repeated until design depths are achieved completing the shaft. It is known that cylindrical structures sustain lateral (earth) pressure mainly through the mechanism of hoop-stress. As Timoshenko’s ring theory goes, a cylinder shell structure is prone to buckling under external pressure [1]. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. However, in shafts with large diameter to wall thickness ratios, buckling could become a critical issue. In any given mode, as buckling occurs in a ring, some sections of the structure move inward while alternating sections protrude. Although the presence of the surrounding soil could mitigate the buckling by resisting the movement (Soil structure interaction) seismic loads can cause ground movements and lateral pressures, exceeding the capacity of the structure. It is therefore essential to design the load bearing capacities of the shaft to minimize the possibility of any catastrophic failure due to earthquakes. This study explores the structural response of the SLS when subjected to seismic loads."

Jan 1, 2016

By Seokwon Jeon, Ho-Young Jeong

"Various numerical methods have been tried to estimate the cutting forces of a TBM disc cutter. In this study, SPH/FEM coupled method was newly employed to improve the traditional FEM analysis. The disc cutter and rock were modeled by Lagrange and SPH codes, respectively. The numerical cutting test was carried out for representative Korean rocks with different cutting conditions. The results show that the cutting forces obtained from numerical simulation had a good agreement with those from LCM tests, and that applying SPH method to rock cutting model has advantages and improvement compared to traditional FEM method. Erosion criterion and erosion limit were not required to simulate the rock fragmentation process, and the cutting forces from the numerical simulation was more stable and accurate. The results indicate that the numerical simulation can be successfully used to estimate cutting performance of a TBM. 1. INTRODUCTION Various numerical studies have been carried out to accurately simulate the limitations of linear cutting machine (LCM) tests. Numerical modelling methods have advantages comparing with full scale tests in terms of cost and time involved. Many numerical methods have been used to simulate rock cutting process by different cutting tools and the studies are summarized in Table 1.In 2D simulations listed in Table 1, because they do not take account of rolling force and horizontal rolling mechanism of a disc cutter, indenter was selected as cutting tool in their modelling. For these reason, 2D modelling is not suitable for rock cutting modelling using a disc cutter. In contrast, 3D numerical models can take account of the indentation process by thrust force and penetration processes controlled by rolling force."

Jan 1, 2016

By Nasri Munfah, Raymond E. Sandiford

"Superstorm Sandy (Sandy) created a storm surge that inundating many of the tunnels that pass beneath the Hudson and East Rivers. The tunnels are vital infrastructure links for the economy of New York City and the northeast region. The sea water, which contains highly reactive salts, caused significant damage to electrical and mechanical systems. In addition, the salt water inundation left corrosive precipitants on the tunnel linings and on and within electrical duck banks. After the salt water was evacuated from the tunnels, condition assessments were performed using a state of the art approach involving high resolution laser scanning, digital imaging, and thermal imaging. These scans were performed prior to hands on inspections. The damage assessment concluded that, although the tunnel structural linings were not damaged, the interior elements of the tunnels needed major rehabilitation to arrest the continual deterioration of the structures. This paper details the state of the art approach used for these tunnel inspections. INTRODUCTION On October 29, 2012 Super Storm Sandy flooded a large number of both transit and vehicular tunnels in the New York Metropolitan area. The region’s transportation network was severely disrupted. The storm damage is estimated to have been in excess of $30 billion, and with the tunnels out of service, the local economy was losing hundreds of millions in economic activity. Restoration of these tunnels was a very high priority and the resulting expedited restoration process did not always provide adequate time for comprehensive condition surveys. This resulted in many of these surveys being conducted after service restoration. Inspecting highly trafficked transit tunnels is challenging and the logistics of working in short night outages led to a rethinking of the conventional inspection approach. Traditionally, visual and tactile methods are first used to inspect tunnels and then quite often followed by LiDAR (Light Detection and Ranging) scanning and perhaps infra-red scanning. For multi-mile tunnels, the time required to visually map tunnel features can be quite extensive. By performing the scanning first and then performing the visual and tactile inspections, one is able to use the scan data to identify the specific areas that need detailed inspections. This approach was used quite successfully for a number of the NYC tunnels."

Jan 1, 2016

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By Takuya Tani, Tomoyuki Aoki, Kazuo Saskai

"The authors have proposed a unique methodology in the evaluation of rock mass stiffness for the range of five to twenty meters ahead of the tunnel face, with the use of small diameter inclinometers. The inclinometers are installed at the tunnel crown at a pre-determined constant interval, about one meter behind the face in order to obtain the slight change in inclination angles during tunnel excavation. This method was developed as a daily control measurement such that the geological condition and its possible change ahead of the face could be detected early by monitoring the trend of inclination angles. This paper describes the results of the ground stiffness ahead of the tunnel face evaluated at a mountain tunnel construction site. This stiffness is evaluated automatically and displayed visually by the current system equipped with a result display screen, together with a warning message against a weak zone when detected. 1. INTRODUCTION In a conventional planning of a mountain tunnel, according to the Japanese Standard (JSCE, 2006) seismic refraction surveys from the ground surface are performed and tunnel support patterns are then designed based on the seismic wave velocity. The resolution of the velocity profile estimated by this technique, however, is poor as the tunnel overburden becomes large. The tunnel face is therefore often encountered by unforeseeable fault zones or weak rocks. Such an unpredictable weak zone occasionally causes the collapse of the tunnel face. Clarifying the forward geological information during excavation is hence significant for safe and well-controlled construction. According to the geological conditions ahead of a face, auxiliary methods typified by forepiling and face bolting could be preliminarily prepared for prompt execution. For the purpose of acquiring forward geological information, pilot borehole drilling and seismic reflection methods represented by the TSP (Tunnel Seismic Prediction) or HSP (Horizontal Seismic Profiling) are often applied. Those exploration are carried out near the tunnel face for a couple of days. This often leads to the interruption of excavation procedure and has no small effect on the construction schedule. On the other hand, some forward ground prediction methods in the daily control measurement have been developed e.g. by Schubert et al. (1995). In this method, tunnel displacements in the direction of the tunnel axis are used together with the crown settlements. We have tested their method at a few of our tunnel projects and found difficulty in the evaluation of the forward ground condition due to insufficient resolution of the axial displacement measured by a total station theodolite that we usually use for the tunnel measurement. We have therefore developed a novel methodology of monitoring slight inclination at the tunnel crown near the face, so that the forward ground conditions can be predicted and evaluated as part of a routine measurement procedure."

Jan 1, 2016

By A. Juganda, Jr. Bogin, S. Saki, R. Gilmore, J. Brune, J. Grubb, S. Lolon

"In longwall mines, atmospheric or barometric pressure fluctuations can disturb the pressure balance between the gob and the ventilated working area of the mine, resulting in a phenomenon known as “gob breathing”. Gob breathing triggers a gas flow across the gob and the working areas and may result in a condition where a methane accumulation in the gob flows into the face area forming an explosive mixtures. This paper discusses results of Computational Fluid Dynamics (CFD) modeling carried out to analyze this phenomenon and its impact on the explosive mixture development under a bleeder-ventilated longwall gob panel scheme. Modeling results indicate that the gas inflow and outflow across the gob and the formation of Explosive Gas Zones (EGZs) are directly affected by the barometric pressure changes. Methane gas and EGZs in the gob expand out toward the face and bleeder entries during the falling barometric pressure. Where methane zones interface with mine air, EGZ fringes may form along the face and in the bleeder entries. When the atmospheric pressure increases, an ingression of oxygen into the gob is observed that can also increase EGZs in volume. The findings from this study help assess the methane ignition and explosion risks associated with fluctuating atmospheric pressures. INTRODUCTION Methane explosions continue to be a daunting risk for underground coal miners, although the number of related fatalities and injuries in the U.S. coal mining industry has steadily decreased since the establishment of the U.S. Bureau of Mines in 1910. Still, the consequences of a methane explosion are often disastrous with multiple fatalities and property damage often leading to permanent shutdown of the mine. Methane is formed during the coalification process and is released from the coal seam to the mine atmosphere when the coalbed is disturbed by mining or natural causes such as earthquakes. If not properly diluted by appropriate mine ventilation, this methane may accumulate in the active mine workings and gob areas. Researchers at the Colorado School of Mines have developed numerical models showing how and where explosive methane may accumulate in gob areas. Historical mine explosions appear to show a connection between mine explosions and fluctuating barometric pressure as a result of stormy weather. McIntosh (1957), Boyer (1964), and Kissell et al. (1973) studied the influence of barometric drops on major coal mine disasters in the United States prior to 1970. Their statistical analyses found that a majority of these disasters occurred in the fall and winter months when the barometric pressures were influenced by unstable weather conditions and noted increased methane content in the mine workings during times of falling pressure. Studies conducted by Fauconnier (1992) and Hemp (1994) found similar connections between methane explosions and barometric pressure fluctuations in a majority of gas explosions in South African mines. Ten out of twelve major mine explosions with five or more fatalities in the U.S. after 1970 were found to have occurred during the months of November through April when barometric pressure swings were more abrupt and intense (Lolon et al., 2015)."

Jan 1, 2016

By Charles A. Stone, Eric C. Wang

"Top-down wall construction was selected to excavate the tunnel portal headwall areas of the ORB East End Crossing tunnel. Benefits included an expedited construction schedule realized by staging excavation and rock support with development of temporary construction access roads. Rock mass properties, proximity to right-of-way lines, and blasting impacts were considered to design suitable lift heights, intermediate bench locations, and permanent ground support systems to provide supported permanent excavations. Carbonate rock formations contained adverse subsurface geotechnical features including solution cavities, clay seams, weathered joints, pinnacled rock, and boulders, which were addressed by flexibility in design. The resulting over-break conditions and long-term water infiltration issues required economic design solutions. This paper discusses the unique considerations required during design of top-down tunnel portal headwalls excavated in carbonate rock formations including temporary excavation and permanent ground support systems which provided flexibility for unforeseen over-break, minimized construction delays, and provided long-term stability. PROJECT BACKGROUND The East End Crossing is an approximate 8-mile highway connection of the Louisville-Southern Indiana Ohio River Bridges East End Crossing (ORBEE) project. Currently under construction, this connection will link State Road 265 in Indiana with the Gene Snyder Freeway in Kentucky to form an outer loop bypassing the Louisville-Southern Indiana metropolitan area. This highway project features a 2,510-foot long, three-span cable-stayed bridge over the Ohio River, and a 1,680-foot long tunnel. The project, being managed by the Indiana Finance Authority and Indiana Department of Transportation, is scheduled to open to traffic by the end of 2016. The new twin three-lane tunnel under the historic Drumanard Estate requires steep cut excavations for approach and tunnel portal walls on the order of 60 feet deep through overburden soil and carbonate bedrock formations. This paper focuses on the design considerations for the permanent support of the top-down wall construction of the tunnel portal headwalls and approach retaining walls."

Jan 1, 2016

By A. Haghighat, B. Lattimer

"Mine face ignition due to a high levels of methane is one of the most common fire incidents in underground coal mines. This work exams ignition scenarios in continuous miner headings. Depending on the magnitude of the ignition or resulting fire, the ventilation curtain in the continuous miner (CM) heading may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to the ventilation curtain on the ventilation flow into the CM area. The computational fluid dynamics software Fire Dynamics Simulator (FDS), Version 6.0 was used to predict the conditions that develop due to a 200 kW fire in the coal mine face following a methane ignition with different levels of curtain damage. Smoke layer depth, temperatures and mass flow into the CM area were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed of the curtain. Partial removal of the curtain allowed more smoke to accumulate in the CM area and a reduction in ventilation into the CM area. With full removal of the curtain, the smoke accumulated through the entire depth of the CM area and flowed out the entrance to the CM area and the ventilation completely bypassed the region. INTRODUCTION Active working faces in underground coal mines are one the most hazardous locations in terms of fire events. According to Mine Safety and Health Administration (MSHA) data analysis, the highest number of non-fatal fire incidents was reported at mining faces, intersections and crosscut areas in comparison with other locations from 2000 to 2012. About 464 fires happened at active working faces from 2000 to 2012, most consisting of a methane ignition, in some cases followed by localized fire. These are high risk incidents due to the potential to raise float dust and damage ventilation systems, particularly auxiliary systems such as curtain or tubing. Depending on the magnitude of the ignition or fire, the ventilation curtain in the continuous miner (CM) area may be damaged or dislodged, affecting the ventilation into the area. Five computational fluid dynamics (CFD) scenarios were considered to investigate the smoke layer depth, temperature, visibility, mass flow rate, and the behavior of airflow in an entry with a continuous miner (CM) located in it. The state of the auxiliary ventilation was varied based on the assumption that as an ignition increases it magnitude it will affect ventilation curtain proportionally. Visibility and temperature along the height of the entry at different sections were investigated and the interface height at each section was determined. Also, the fresh air height was studied for tenability analysis in future. FDS, Version 6.0 was used to predict the conditions that develop due to a 200 kW fire on the coal mine face following a methane ignition with different levels of curtain damage. Smoke view software was used as the post processor to visualize and analyze methane fire behavior at the face. Most entry fires are reported as fuel-controlled fires as they are rarely restricted to air access (Ingason et al, 2014). The working face fire in the following models was assumed to be a fuel-controlled fire."

Jan 1, 2016

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

By Roger Storry, Donald Bruce, Arnaud Hochart

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands and under the main shipping channel in Biscayne Bay (Figure 1).The POMT was a unique project which embodied many technical firsts and involved the first large diameter tunnels constructed through Florida’s challenging sedimentary carbonate strata. At the outset, a comprehensive ground investigation was performed, using both conventional and less conventional investigation techniques, to characterise the highly heterogeneous ground conditions.The findings of the investigation had a major impact on the tunnelling methods, triggering a series of mitigation works to ensure that the tunnels could be excavated safely and effectively. The mitigations included modifications to the already designed Tunnel Boring Machine (TBM), to facilitate an innovative excavation process, and a unique grouting campaign (Storry et. al. 2013a). The project was completed and opened to traffic in August, 2014 and has significantly alleviated traffic congestion in Downtown Miami.GEOLOGICAL CONTEXTThe geological conditions at the project site consist of carbonate sediments which can be divided into distinct geologic units; the Miami Limestone Formation (Layers S3, S4), the Fort Thompson Formation (Layer S5), the Anastasia Formation (Layer S6), the Key Largo Formation (Layer S7) and the Tamiami Formation (Layer S8). Multiple changes in sea level over a relatively short geologic time scale have resulted in a heterogeneous profile consisting of interbedded sedimentary rocks and sediments, which vary widely, both vertically and laterally (Figure 2)."

Jan 1, 2016

By David Caiden, Petros Fortsakis, Alan Hodgkinson

"1. INTRODUCTIONDo contractual practices affect project outcome? Can better contractual practices improve the likelihood of project success? The consensus amongst experts is that better contractual practices really do improve project outcomes. With this in mind the members of the International Tunnelling Association (ITA) Working Group 3 on Contractual Practices (WG3) pooled their collective knowledge to publish in 2011 the document entitled The ITA Contractual Framework Checklist for Subsurface Construction Contracts (ITA Working Group 3, 2011). Written for projects involving significant subsurface works, e.g. tunnels and caverns, the ITA Framework Checklist explains the major contractual issues that must be considered to ensure a successful project. Its goal is not to specify how each issue should be resolved, but rather to highlight the issues and give recommendations on how they should be addressed. The Checklist is compatible with, and provides guidance for reviewing, standard contracts such as FIDIC and NEC. One of the authors is a co-author of the Checklist and has contributed to previous papers describing the Checklist and its applicability to hydropower projects (Hodgkinson & Wilson 2014, Hodgkinson & Wilson 2015). The Checklist identifies a series of issues that should be contractually defined, which can be summarized as follows: •,Methods for dealing with geotechnical uncertainties should be defined in the contract •,There should be an appropriate level of geotechnical/geological investigation •,Sufficient mobilization periods should be allowed •,Sufficient time should be allowed for testing and commissioning •,Procedures for timely dispute resolution should clearly defined •,Quality and performance requirements should be clearly defined and measurable •,Provision should exist for cost consequences of unforeseen circumstances •,Dispute resolution processes should be clearly defined •,Payment processes should be fair and clearly defined •,Risk should be clearly allocated and parties should be able to bear the risks they carry •,There should be a mechanism for adjusting payments according to conditions •,The risk management approach should be clearly defined •,Admeasurement or unit price approaches are recommended •,The responsibilities of each party must be clearly defined •,The consequences of non-performance should be clearly defined •,The construction programme (schedule) should be realistic."

Jan 1, 2016

By Petr Salak, Adrian St. John, Angelos Gakis

"INTRODUCTIONCrossrail will provide London and the South East of England with a world class, high-capacity railway to ease congestion on London’s public transport system and enable better access between business, residential and entertainment districts. At the heart of this £14.8bn scheme lies Farringdon Station, which will form a major interchange between Crossrail, Thameslink and London Underground. The £400m Farringdon Crossrail station was awarded to a joint venture of BAM Ferrovial Kier (BFK) in 2011, and comprises two ticket halls, two platform tunnels and a multitude of connecting tunnels all constructed using open face sprayed concrete linings (SCL). BFK appointed Dr. Sauer & Partners (DSP) as their specialist SCL designer. As the main contractor for both C300/C410, the Western Running Tunnels and Station Caverns, and also for C435 Farringdon Station, BFK were in a unique position to develop strategies to reduce cost, time and risk for the Client. One such innovation involved the continuation of the TBM drives for the running tunnels right through the length of the new Farringdon platform caverns. This created large diameter precast concrete pilot tunnels for the subsequent platform enlargement using SCL. The benefits of such an approach are described in detail by St.John et al 2015. BFK also introduced another alternative strategy to reduce cost, time and risk, by proposing to abandon the TBMs in the ground (“Turn & Bury”) permanently rather than recovering them through the ticket hall shafts. This de-risked the programme, enabling critical ticket hall construction to proceed unhindered. However, one consequence of this revised strategy was an area of increased underground congestion, with two SCL tunnels (RTE2 and ES2) and a bored tunnel (complete with abandoned TBM) in close proximity to a ticket hall excavation (see Figure 1) and a sensitive, listed railway structure. Faced with this complex geometry, and combined with challenging geotechnical conditions (Gakis et al 2015), the team chose to install enhanced monitoring to study the behavior of tunnel RTE2 and provide additional assurance that the tunnels were performing as predicted. Applying advanced 3D numerical modelling and taking into account the residual tensile strength of the SCL helped avoid unnecessary reinforcement installation in primary lining and/or early installation of a secondary lining in RTE2 prior to ES2 construction."

Jan 1, 2016

By Ignazio Carbone

"During the design of a typical modern subway, engineering aspects prevail since underground structures remain hidden to most humans. Aligning the advanced architectural concepts with the engineering requirements of the Naples Metro Line 1 (Italy) called for a thorough rethinking of the design process so that the engineering could be kept aligned with the architecture, integrating seamlessly the two with the construction methods, standards and technology.The preliminary design process consisted of three major phases: •,geotechnical and geological issues, preselection of construction methods; •,functional scenario based on engineering and construction requirements; •,review and merging of the architectural concept with the functional and engineering aspects. The last phase proved the most demanding one, matching the first outline sketches with the applicable construction methods. This required continuous alignment of approaches, eventually leading to the design consistent with the original architectural vision, yet fully compliant with the engineering and construction framework. At the beginning general information on Line 1 will be provided, followed by some main features of the construction work along the Dante – Garibaldi section both for the tunnel and the stations. At the end, the selected methodology and the related consequences on the functional, technical and architectural design will be outlined.City of Naples current municipal transportation plan envisages a circle ring line for the metro line M1. Actually it’s open to public the segment Piscinola – Dante – Garibaldi run by AMM, municipal company. This ring segment has been built by Metropolitana di Napoli, while Napoli Metro Engineering (company belonging to MMspa Group) is in charge for the planning of entire system and construction management. Line 1 connects Piscinola-Secondigliano northern periphery to Vomero shopping neighborhood, downtown and Central Railway Station."

Jan 1, 2016

By J. E. Dreier, R. E. Scheffel, A. Guzman

"This paper outlines a comprehensive, cost-effective testing program for the acid-ferric sulfate heap leaching of oxide, supergene and primary copper ores. It is based on extensive experience in copper heap leaching and uses the many technological advances in the field developed over the past several decades. The approach described requires firstly a detailed resource evaluation, then a hydrodynamic characterization of representative samples and, finally, a focused metallurgical testing program. The principles communicated here can be applied to other acid leachable minerals. The program varies considerably from conventional testing in its disciplined, orderly, step-by-step approach, its application of hydrological and chemical principles to leaching, and its reliance on fewer, more tightly controlled column tests. The purpose of the test program is to optimize the financial, time and other resources devoted to the program, while minimizing the financial risks to the development company or companies and the project funding providers. IntroductionThe major goal of any process development testing program should be the successful implementation of the project. With respect to heap leaching, the metallurgical testing program plays a critical role in the larger objective, as described in Scheffel (2013, 2014). McNulty’s series of papers (1998, 2004, 2014) confirm that the success of any project is directly proportional to the extent and quality of the testing program on which the process is designed.Therefore, a key development objective is to conduct a well-focused metallurgical test program. While the primary focus of this paper is copper, the acid leaching of any substance would benefit from a similar approach.This paper addresses primarily the sulfate system, which is compatible with the bioleaching of sulfide minerals. Nicol et al. (2011) described the advantages of the chloride leaching of copper sulfide minerals. United States patents Nos. US 2009/0173188 A1, US 8,597,933 B2 and US2015/0232963 A1, assigned to BHP Chile Inc. and BHP Billiton S.A. Ltd, describe methods for both the oxidative and nonoxidative leaching of primary and secondary copper sulfides. Reyes (2013) and Ipinza and Flaquer (2014) described commercial applications of chloride-based heap leaching. The testing disciplines discussed in this paper will also apply to the development of an acidic chloride leaching system."

Jan 1, 2016

By Gerald Pinter, David Nitsche, Márton Bredács, Markus Haager, Andreas Frank

"The reliable prediction of service lifetime of tunnel constructions is of essential technical and economic interest. Polymers used for tunnel liners have to fulfill the requirement of 100 years lifetime. However, today no reliably proven test method is available which confirms such long lifetimes. The current paper introduces a recently started research project which focuses on lifetime prediction of highly flexible, very low density polyethylene (VLDPE) for tunnel geomembranes. Different PE grades in combination with different antioxidant packages are conditioned at elevated temperatures and immersed in different media. Initial results confirmed significant material aging of unstabilized resins already after exposure of up to 34 weeks, at least at the highest exposure temperature of 80 °C. To consider application relevant material properties the material characterization was done by means of tensile tests and dynamic oxidation induction temperature tests. High pressure liquid chromatography was used for further investigation of antioxidant consumption kinetics. 1. INTRODUCTION For a reliable service of modern tunnel constructions a sustainable proofing against water infiltration is essential for the lifetime of the structure. Geomembranes made of polymeric materials have been used successfully for tunnel lining since several decades. Whereas previous geomembranes usually were made of plasticized polyvinylchloride (PVC-P), due to several technical advantages today very low density polyethylene (VLDPE) has become a more and more popular material for such applications. For modern geomembranes, current guidelines expect minimum lifetimes of at least 100 years (ÖBV-Richtlinie 2012). In contrast to this requirement it must be considered that today no test methodology is available which reliably confirms such long lifetimes of polymeric materials."

Jan 1, 2016

By Xuehui Zhang, Yun Bai, Qiaosong Li, Huiming Wu

"Construction activities account for a large share of the global Greenhouse Gas emission. In the past 10 years, project decision-makers and researchers have been paying more attention to the carbon emission of tunnel projects. In this paper we study the carbon emission calculation in shield tunneling. The objective of this paper is to: (1) analyze the complex variables which affect the total emission of shield tunneling; (2) develop and illustrate a new data-mining-based method to estimate the carbon emission in the construction phase; (3) assess the emission prediction reliability of a data-mining-based method—the Randomforst model, with R programming language. This study is based on a large-diameter shield tunnel built in Shanghai, China, and shows that a reliable predictive performance can be achieved with this new data-mining-based method. INTRODUCTION Climate change caused by the Greenhouse Gas (GHG) emission has been a hot topic in recent 20 years. Both governments and non-government-organizations are trying its best to control the climate change. Since the 1990s, the general consensus is that carbon emission reduction and carbon sinking (the work of capturing the emitted carbon) are two ways of mitigating the global warming effect, with the former being more exercisable. The challenge posed by global warming also motivates the project decision-makers to take measures to reduce the GHG emission. The 5th Assessment & Report on Climate Change (published by IPCC, the Intergovernmental Panel on Climate Change) suggests that building industry contributes to 5% of the total direct emission. The building industry has shown more awareness of the impact of GHG emissions with construction activities. Shield tunnels act as an important component of the infrastructure system, and have been the dominant way of utilizing the underground space, as well as a competitive alternative to passageway underneath rivers. To study the environmental effects of shield tunneling, there is a need to quantify the carbon emission of shield tunnel construction."

Jan 1, 2016