Search Documents

By R. Hogg, E. Kaya

The presence of agglomerated particles in airborne dust in coal mines has been confirmed by SEM examination of static samples collected on substrates. In addition, the effect of agglomerated particles on the performance of cascade impactors and cyclone- type personal samplers has been studied. Simple procedures have been developed for evaluating the extent of agglomeration in air-borne dust by comparing the observed size- selectivity of the sampling devices with that expected under idealized conditions. Applications of these techniques in the laboratory and in underground mines are discussed.

Jan 1, 1992

By R. H. Grau

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing some practical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers? exposure to airborne contaminants.

Jan 1, 2008

By T. Ruff, J. Steele

The lack of visibility near earthmoving equipment results in an average of five fatalities in U.S. surface mines each year. These accidents occur when a piece of equipment either strikes another vehicle or worker, or travels over the edge of an embankment. Researchers at the National Institute for Occupational Safety and Health have evaluated off-the-shelf proximity warning systems that sense obstacles near the equipment and provide an alarm to the operator. Limitations of existing systems have necessitated the development of new systems designed specifically for mining equipment, including a GPS-based proximity warning system and a computer-assisted stereovision system.

Jan 1, 2004

By Rimas Pakalnis, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

Jan 1, 2005

By S. A. F. Murrell, M. Hong, L. J. Bond

This paper investigates the propagation, interaction and scattering of explosively generated seismic waves with discontinuities in rock masses using numerical models which employ a finite difference method. The models consider 2-D systems and give a full solution including mode-conversion in the mid-frequency scattering region where feature dimensions are of the order of the wavelengths involved. The paper has two parts, the first of which considers wave propagation and diffraction by simulating an explosive body source in a half- space containing a step or a slot on the surface which represent a cliff and a rift valley that has dimensions of the order of the wavelengths in the source. The second part of the paper reports a hybrid technique which combines a perturbation method and the finite difference method for wave propagation again caused by an explosive body source in a 2-D half-space system but with a shallow surface obstacle, such as a smooth ridge, with elastic constants slightly different from bulk material and the slope of this surface topography are shallow. This hybrid technique is also reported being applied to a half-space with a horizontal void or insert.

Jan 1, 1986

By Pablo Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occuring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, California recovers potash from natural brines, but uses fuel to accomplish evaporation. Under proper meteorological conditions the use of solar evaporation might be desirable from the economical standpoint. Of course, this may not be true when, if by artificial evaporation, a group of very valuable salts are recovered. This is the case of the American Potash operation at Trona. Solar evaporation has its limits. The working temperature is low. We may say, just to cover most areas of the world where solar evaporation may be practical, that it will take place between 18°C and perhaps around 45°C. In most cases the average working temperature expected will be around 25°C.

Jan 1, 1963

By Chris Laughton, Bernhard Spoerr

"Tunnel inspections are increasingly needed to ensure that aging infrastructure does not fail in service. To this end the time between inspections is being reduced, the thoroughness of each inspection is being increased to provide for a more detailed assessment of conditions and inventory defects. The conventional Tunnel Report, containing hand-drawn maps and/or photos, and a log describing observed defects and areas of deterioration, is being increasingly replaced by LiDAR generated 3-D surface maps. The data collection process that traditionally supports development of a Tunnel Report is labor-intensive, taking crew-days of engineering effort, and requires partial or full stoppage of tunnel operations. In an urban setting, such multi-day interruptions in service are difficult to countenance for a near-capacity tunnel operation. Under time pressures, the detail and accuracy of the manual inspection process will inevitably be compromised, resulting in a high cost, low quality product. As the tunnel inspection window decreases the argument for incorporating laser scanning in to the inspection process is increased dramatically... The 3D scan technology allows detailed and accurate data to be collected within the tight time frames demanded by the owners and operators of critical infrastructure. Not only does the use of laser scanners improve the 3D accuracy of the data collected, it also, enhances the efficiency and safety of the inspection process, reduces data collection and processing costs and enhances the reliability of results over time. The paper will also demonstrate the value of adding photogrammetric data to the 3D Model to show surface defect discoloration. The accurate and detailed data collected by a combination of LiDAR and photogrammetric techniques provide superior data needed to inform critical asset management decisions related to maintenance, repair and replacement."

Jan 1, 2016

By Satya Harpalani

An investigation was carried out to study the microscopic structure of coal in order to understand the phenomenon of methane migration. A Scanning Electron Microscope (SEH) was used to study the surface and pore structure of bituminous coal taken from an underground mine. Micrographs obtained showed the highly porous nature of coal which explains the large quantities of gases that remain within the pores in the compressed and adsorbed forms. These micrographs further showed that most of the pores within the coal matrix are the 'dead-end' type and do not contribute much towards the flow of gas. The most important finding was that solid coal has a network of cracks and fractures indicating that it is these cracks that are primarily responsible for the gas flow, rather than the pores. The size and distribution of the pores within coal influence the capacity of coal to retain methane but movement of the gas molecules is the responsibility of the microfractures. Any mathematical modeling to simulate gas flow through coal must take this into account. For purposes of modeling, the structure of coal can be considered to have dual porosity. First, the gas molecules are released from the pores and there is a gradual migration towards the fractures. Once the gas reaches the fractures, its movement is eased greatly along these fractures.

Jan 1, 1987

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

By Jaime Lomelin

The brines from the sub-surface of the Laguna del Rey dry lake are pumped to Química del Rey, S. A. plant, where they are cooled in adiabatic crystallizers precipitating sodium sulphate decahydrate. This salt is dehydrated in multiple effect evaporators and dried in rotary kilns producing high purity anhydrous sodium sulphate. The spent brines from the sodium sulphate operation are concentrated in solar ponds, precipitating astrakanite and leaving a brine with a higher concentration of magnesium ions. This brine is treated with calcium chloride solution to eliminate the remainder of sulphates, leaving a solution of magnesium chloride ready for the manufacture of refractory grade magnesium oxide or periclase. The magnesium chloride is reacted with dolime to produce magnesium hidroxide which is washed, filtered, and calcined to produce soft burned magnesium oxide, which is briquetted and dead burned to produce the periclase.

Jan 1, 1984

By P. Legast

Serpentinite minerals are available in large quantities from asbestos mining activity. The granular or fibrous serpentite, at temperatures greater than 700°C, will recrystalize into olivine, forsterite and enstatite. These minerals have been used and studied for decades and are environmentally safe. The thermal process changes the composition and properties of the original mineral. Therefore, the substitution of the original mineral cannot simply be made and the applications for these new synthetic minerals need to be redeveloped. The two original mineral forms allow a wide range of new synthetic raw materials which can be adjusted to specific applications or custom needs.

Jan 1, 1993

By D. Lelinski, X. Nie, J. D. Miller, J. Hupka, K. Bukka

A preliminary characterization of soil components contaminated at a low level (7 nanocuries per gram) with toxic/radioactive metals has been carried out. Most radioactivity and metals content were present in the minus 100 mesh (<150 µm) size fractions. None of the size fractions examined qualified for uncontrolled disposal at dump sites, thus all material would have to be moved to discharge-controlled landfills. The metal content of the sample was below the limits for economical recovery, therefore eventual processing would be dictated by environmental concerns.

Jan 1, 1992

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By L. L. Gagné

The Churchill Falls Development will eventually be the largest source of hydroelectric power in North America. Churchill Falls was discovered in 1839, but until recent years it was not practical to begin development of this site to tap the 7 million horsepower available. This $1 billion project is located in Labrador, 700 miles northeast of Montreal and 650 miles northwest of St. Johns, Nfld. The construction will divert the Churchill River 5 miles upstream from the 245 foot Churchill Falls. Rapids above and below the Falls, together with the Falls proper, give a natural head of 1,040 feet. In contrast to the basic simplicity of the surface installations, the powerhouse labyrinth is astounding in size and complexity. The largest in the world, it consists of three major chambers - the powerhouse, 972 feet long by 81 feet wide and 154 feet high; the surge chamber, 763 feet long, 40 feet to 64 feet wide and 148 feet high; and the transformer gallery, 856 feet long by 50 feet wide and 39 feet high. Other major features include eleven inclined penstocks, each 1200 feet long and 20 feet in finished diameter; eleven draft tubes averaging 37 feet in finished diameter and 162 feet long; six vertical cable shafts each an average of 865 feet in length; a series of eleven short bus tunnels linking the powerhouse and the transformer gallery; a vertical power-

Jan 1, 1997

CVRD was established on June 01, 1942, during the Second World War, through an agreement between Brazil, the United States and the United Kingdom, to produce 1.500.000 tons/year of iron ore from Itabira mines in the State of Minas Gerais. As a result of several circumstances and political problems (the end of the 2nd World War reduced the Anglo-American support to its development and implementation), the venture just reached the originally targeted production 10 years after its establishment, operating within a mine, railway and port integrated system. Currently, this operational system from the South of Brazil owns mines in the State of Minas Gerais with an annual capacity of approximately 65 million tons, 900 km of railways, of which more than 500 km is a double line railway, six pelletizing units and the Port of Tubarao for ships with large carrying capacity.

Jan 1, 1994

By M. A. Berdine, C. N. Thompson, D. Brock

The raise bore method of shaft construction has been success-fully used in the mining and construction industries for over thirty years. In the mid 1990’s, Twentymile Coal Company (“TCC”), now affiliated with RAG American Coal Company, used this method for a moderately deep small diameter shaft and the raise bore and slash method for a shallow larger diameter shaft. In late 2001, TCC contracted to raise bore a 431-meter deep, 6.2-meter diameter shaft. During the raise bore and shaft lining processes, regional horizontal stress fields resulted in extensive elliptical caving beyond the original design diameter. This paper discusses the engineering approaches and procedures used to safely complete construction of the raise bore shaft.

Jan 1, 2004

By Zefang ChenLi, Laijun Ma, Lei Mao, Fang Lian

"In our work, the preparation technique of high pure manganese sulfate directly from low-grade rhodochrosite ore (MnCO3) was studied and improved intensively, including the effective leaching process and the short purifying process. Based on the same ion effect, the repeated leaching of rhodochrosite with sulfuric acid is proposed to improve the solubility of Mn2+ and inhibit the dissolution of the impurities Ca2+ and Mg2+. Moreover, the repeated leaching process could make full use of rhodochrosite and lower the dosage of sulfuric acidas raw material. With the aid of theoretical calculation, Ba(OH)2 was chose to adjust the pH value of manganese sulfate solution, and BaF2 to remove Ca2+ and Mg2+completely in the process of purifying. The results demonstrate that the extraction ratio and the recovery ratio of manganese reached 94.3% and 92.7%, respectively, which shows the prospect of industrial application. In manganese sulfate production, the heavy metal impurities have been decreased to less than 1ppm. Moreover, the content of calcium, magnesium and sodium has been decreased to less than 20ppm, which meets the standards of high pure reagent for energy and electronic materials. Our study enlightens an approach to the sustainable application of low-grade rhodochrosite.Introduction Low-grade manganese carbonate ores (=14%) becomes gradually the main resources for exploitation and applications in China according to national mineral resources survey (Tan et al 2004 and Singh et al 2017). Therefore, the electrolytic deposition technique of rhodochrosite faces great challenges including low electrolysis efficiency, high-resource input and high-pollution discharge (Fu et al 2010, Michelis et al 2009, Zhang et al 2013). Recently, more and more amount of manganese series with high or super high purity such as MnSO4, MnO2, Mn3O4 and MnO is demanded with the development of energy and electronic materials. Due to low-grade ores containing multiple elements such as iron, silicon, calcium and magnesium, conventional preparation of manganese sulphate with high purity from electrolytic product is characterized by long production-cycle and high-energy consumption (Subrat et al 2011, Mpho et al 2013). By contrast, hydrometallurgical method combined with thermal decomposition, hydrothermal synthesis and sol-gel processes has been widely studied because of its high efficiency, low consumption and low cost (Chen et al 2008). But the key problem in direct preparation of manganese series form low-grade rhodochrosite is to remove completely the multiple impurities such as iron, silicon, calcium and magnesium (Liu et al 2014). So it is urgent to develop a sustainable alternative approach with character of short process, high efficiency and environmental friendly."

Jan 1, 2017

By J. A. Oraniscak

Longwall mining operations continue to increase extraction rates and the potential to generate higher amounts of airborne respirable dust (ARD). The National Institute for Occupational Safety and Health (NIOSH) has gathered data from underground longwall surveys and laboratory crushing tests to identify the important factors influencing the amount of ARD levels generated. Coal-seam characteristics, operational parameters (i.e.,cut sequence, mining height, etc.), extraction rates and dust-control parameters (i.e., airflow, water flow, etc.) were examined to determine their influence on ARD levels measured at longwalls during actual mining operations. ARD generated by a laboratory crusher while crushing bituminous coal samples collected from underground longwalls was also examined to determine if there were cor relations with coal-seam properties. Results from the longwall and laboratory data collected indicated that low-ash, high-volatile coals (low moist fuel ratio or MFR coals) generate higher amounts of ARD. It was found that face ventilation and water application to the coal product are essential elements to controlling longwall ARD levels.

Jan 1, 2000

By Jeffrey J. Schwoebel, Jianliang Li, Daniel J. Brunner

A United Nations (UN) administered degasification technology transfer project, funded by the Global Environmental Fund (GEF) is underway at the Shihao Mine of the Songzao Coal Mining Ad- ministration in the province of Sichuan, Peoples Republic of China. This mine exploits multiple seams at depths ranging from 300 to 600 m below surface. In-seam boreholes and frequently spaced in-mine vertical boreholes, developed from underlying galleries constructed specifically for this purpose, currently degasify the seams in advance of mining at the Shihao Mine. Because of ventilation system constraints and the in-situ gas con- tent, longwall mining of the coals at this mine could not proceed without some form of pre-mining degasification. This paper presents a simulation based degasification plan of long, in-seam horizontal boreholes for the Shihao Mine. Simulations with a coalbed reservoir program assessed time dependent degasification characteristics of both vertical and in-seam horizontal boreholes. The simulations used input data from reservoir and desorption tests conducted at the mine site. The results produced system design nomograms to assist mine engineers in defining the appropriate borehole spacing necessary to degasify the seam in the time available for pre-mining drainage. The predicted effectiveness of the current vertical degasification scheme was compared with that for a horizontal borehole program and served as the basis for the recommended in-seam borehole configuration for the project at the Shihao Mine. The horizontal borehole degasification program requires substantially less gallery and borehole development than the present vertical degasification scheme.

Jan 1, 1997