Search Documents

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

Jan 1, 2006

By G. E. Sreedhar, R. Kumar

The pockets of high silica blue dust across the entire high grade hematite deposits in the Bailadila sector bothers the excavation activity due their iron content, which is higher than the threshold value specified by the Indian Bureau of Mines and the agony of stacking them separately due to their fragile & powdery nature. The physical nature of blue dust and its negligible alumina content makes these a potential source of hematite, which is a blessing in disguise. As most of the particles are in the form of an independent grain making it appropriately suitable feed for dry magnetic separation and thus the dry beneficiation has turned a bane into boon by enabling to produce concentrate either suitable for using as DSO or amenable for blending. The emphasis on carrying out dry beneficiation studies in the present context serves the purpose of mineral conservation, mitigates the issues of excavation and stacking as well as conservation of water resource. This paper describes the laboratory and pilot scale dry beneficiation studies carried out on blue dust of 48 – 60%Fe and Silica up to 30% at 25 Kg/hour to 400 Kg/hour, resulting in production of concentrate assaying 60 – 65%Fe. INTRODUCTION High silica blue dust (HSBD) is associated with Banded Hematite Quartzite (BHQ) and is available in abundance in various pockets across the Iron ore body in the Bailadila region of Chhattisgarh state. High Silica Blue dust occurs in the form of free granular particles and also as friable lumps. The chemical quality of this falls under sub-grade category (45 – 55%Fe) and as per the guidelines of Indian Bureau of Mines, these are to be stacked and conserved as future resources of Iron if it can’t be utilized in the present circumstances. Due to its friable nature, stacking of HSBD is a challenge and it is also compounding the problem by polluting the air under high velocity wind conditions. Because of its physical nature and occurrence in pockets pose challenge to systematic mining. The existing processing set up of the operating mines is designed to treat either Direct Shipping ore (DSO) or Run-of-Mine (ROM) have grade >60% Fe. The present practice of beneficiating iron ore fines (<1 mm) comprise combination of two or more processes such as desliming, hydraulic classification, magnetic separation and flotation apart from requirement of grinding depending on liberation characteristics. The HSBD which is predominantly occur as free granular particles, is significantly low in its alumina content. This gives us an opportunity to utilize them by exploring a suitable beneficiation process so that the concentrate produced can be used as a sweetener for alumina rich iron ore/concentrate. Thus, in the present study, an attempt has been made to adopt dry high intensity magnetic separation technique to explore the amenability of the high silica blue dust for beneficiation.

Jan 1, 2019

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation&apos;s Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By Kadri Dagdelen, M. Waqar Asad

Cement production involves the processing of raw materials that contain - Si02, A1203, Fe203, CaO, MgO, LOI (loss of ignition), S03, K20, Na2O, Ti02, P2055 and Cl- to produce the synthetic mineral mixture called "clinker". The use of other additives - sandstone, flyash, iron ore, and clay - is also mandatory in order to achieve the optimum blending requirements of cement. However, the use of these additives needs to be minimized due to their significantly higher costs ($/Ton). This paper presents a mixed integer programming (MIP)-based optimum quarry scheduling algorithm, which is used to generate quarry plans, satisfying geometric and production capacity constraints while providing minimum cost/optimum blend of raw materials mix to a cement plant. The benefits of this new methodology are demonstrated on a case study.

Jan 1, 2002

By M. Sengupta, N. I. Johansen, A. K. Sinha

In Arctic surface mines, frozen ground adds to the complexity of slope stability analysis. The seasonal temperature change may thaw permafrost, and this thawed ground is often unstable. A computer program, GEODYNE, was used to simulate the movement of the thaw front in bare and insulated permafrost slopes. The simulation shows that the insulation can be used on mine slopes to prevent thawing.

Jan 1, 1990

By N. Arbiter

During the first four decades of flotation practice, close to 200 machine designs were patented, although only about a score were ever used commercially. By the end of that period, the rigors of use had resulted in obsolescence of most pneumatic cells, with a few mechanical cells dominating the field. After World War II, newer designs began to appear but most were modifications in varying degrees of older designs with special features added. Of the dozen or so most recent developments, almost all are pneumatic, relying on compressed air instead of impellers for motive power, although in several cases pumps supplement compressors. Table 1 lists a few of the more fully documented new cells, with their significant characteristics, along with similar characteristics of a widely used mechanical cell. New designs in general are emphasizing: bubble size control; in several cases, methods for delivering feed directly to the froth; methods for introducing and dispersing air through nozzles, eductors, packed beds, or permeable walls; and variable cell volumes, relative to capacities, ranging from very small, with less than a second of retention time, to the largest, with retention times of over 20 min. An important question is the extent to which any of the newer designs are based on locating weaknesses in current mechanical cell designs and then using these as a starting point for innovations. In the present study, the key subprocesses which must take place in a cell are outlined; mechanical cells are analyzed to establish where weaknesses may exist; and then alternative subprocesses are considered which could effect improvements. COMPONENTS FOR CELL DESIGN It is assumed that mineral surface chemistry has been modified as necessary to provide optimum potential floatability. While the cell process may affect this to a degree, cell design is primarily concerned with actualizing the existing potential floatability. The cell design problem is to provide more effectively for the following: 1) Dispersion of air to obtain an optimum bubble size distribution at an optimum ratio of air volume to feed volume. 2) A hydraulic environment which permits most effective contact of potentially floatable particles with bubbles: [Table I - Cell Comparisons* Cell Type Mechanical Column Deister Miller ASH No. of units Multiple Single Single Single Retention time min.10/20 17/27 3.8 ca. is Capacities mt/m3s 0.022/0.066 0.066/0.20 0.11 10.4 st/ft3d 1/3 0.3//0.9 m5.0 469 Air hold-up % 15/20 20 n.a. 50/80 Air escape velocity m/s 0.015/0.0200.020/0.025 n.a. n.a. ft/m 3/4 4/5 n.a. n.a. * References: Mechanical (Harris, 1976,1985), (Bassarear, 1985); Column (Travis, et al. 1987); Deister (Zipperian and Christophersen, 1985); ASH (Air-Sparged Hydrocyclone) (Miller 1989).]

Jan 1, 1989

By Jim W. Rosteck, Anthony Del Vescovo

In December of 1992, the City of New York, Department of Environmental Protection, solicited bids for Contract 543B. The low bidder was a joint venture of Schiavone Construction Co., Inc. and the J. F. Shea Co., Inc. When completed, the project provides a 4.88 meter diameter water tunnel 8,840 meters long. This paper presents a case history of the equipment and construction methods utilized for this, the first portion of the New York City Water Tunnel constructed by use of a tunnel boring machine.

Jan 1, 1997

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By R. Shields

"Hard rock mines move large volumes of material. But the conveyors essential to this movement suffer lots of problems, including carryback, spillage, dust, and belt wander. Many of these issues are created at the transfer points where the belts are loaded. This presentation will start with an overview of the latest transfer point systems that incorporate safety and serviceability by design. It will then report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, Nevada. Here performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine. THE IMPORTANCE OF TRANSFER POINTS Conveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance are the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created. The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material—cargo released in the form of carryback, spillage, or airborne dust—that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems, and issues with community relations. As estimate attributed to the U.S. Mine Safety and Health Administration (MSHA) notes that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points. TECHNOLOGIES TO IMPROVE TRANSFER POINTS A number of techniques to improve the performance of conveyor transfer points have been developed. They include: • Absorbing impact, to prevent damage to belt, belt support systems, and conveyor structure, and reduce spillage caused by the impact energy arising from long material drops or large lumps of material loaded onto the receiving belt. • Stabilizing the belt line, to eliminate sag that allows spillage and encourages material entrapment that can damage the belt. • Protecting the skirtboard seals, by sheltering the sealing strips from the mass of cargo pushing material toward the edges of the belt. • Using self-adjusting, multiple-barrier edge seals, to keep material on the belt by providing long-lived seal efficiency with minimum maintenance requirements. • Controlling and centering the belt’s path, to eliminate belt wander and the spillage and damage it can cause. • Allowing dust to settle, through the incorporation of chutework that provides expanded stilling zone and the use of dust curtains at the points where the belt enters and exits the transfer. • Adding supplemental dust control systems, through the installation of systems for passive dust gathering, water-based dust suppression, and/or active dust collection."

Jan 1, 2017

By Merrill P. Allen

The Vernal phosphate rock concentrator is located in the Uinta Mountains near Vernal, Utah. Ore is sedimentary rock from the Phosphoria Formation. Truck and shovel mining is done at a rate of 11,500 TPD. Run of mine ore is crushed and then milled through a SAG mill and ball mill to minus 16 mesh. Milled ore is deslimed using cyclones and hydrosizers. Sands are conditioned with fatty acid, petroleum sulfonate, diesel fuel and frother prior to primary rougher and cleaner flotation. Primary flotation tailing is milled to 95% minus 48 mesh, deslimed in cyclones, conditioned using reagents previously described, and then processed through rougher and cleaner scavenger flotation. Product of scavenger cleaner concentrate is upgraded by reverse flotation of dolomite. Flotation concentrates are combined and dewatered, pulp being milled to 99.5% minus 65 mesh and then thickened to 65% solids. Product is pumped from storage through a 10 inch, 94 mile pipeline to a conversion plant at Rock Springs, Wyoming. Mill tailing is stored behind an earthen dam, water from the settled tailing being reclaimed for mill use.

Jan 1, 1993

By R. Jin

Fine coal flotation using gaseous carbon dioxide has demonstrated the potential for producing superclean coal. The success of this new flotation .procedure is attributed to the coal&apos;s high adsorption potential for CO2. To understand the nature of gas-phase CO2 adsorption at the coal surface, in-situ FTIR spectroscopy in a controlled-environment chamber with an ultravacuum sys-tem has been used and the results are discussed in view of other experimental results from differential scanning calorimetry. It has been found that specifically adsorbed CO2 molecules at the coal surface are polarized and have a characteristic doublet at 2336 and 2361 cm-1. Two adsorption states have been proposed to account for the doublet observed from in-situ FTIR spectroscopy measurements. It is believed that the band at 2336 cm-1 originates from the activated site adsorption of CO2 and that the band at 2361 cm-1 arises due to the molecular aggregation of CO2 within the coal pores.

Jan 1, 1988

By D. Gove

All mining operations using trucks have a common need to properly match the number and size of hauling units (trucks. wagons. scrapers. etc.) to a loading unit (wheel loader. hydraulic shovel/excavator, cable shovel. push tractor. etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length. grade. or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool which, among other things, can be used to optimize the truck-loader match.

Jan 1, 1994

By André Vien, Robert Edwards, Rob Perry

A metallurgical control application can only succeed if the system&apos;s lowest common denominator, its instrumentation and regulatory control is implemented and maintained correctly. This paper describes the basics of regulatory control implementation including some practical guidelines for instrumentation installation, operator interface design, loop tuning, and continuous loop performance analysis. Tuning and analysis techniques are illustrated by step-by-step industrial examples. A small investment in basic control pays dividends in better overall plant performance and provides a solid foundation for advanced control efforts such as expert systems.

Jan 1, 2000

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By J. E. Warm

Florida’s ancient beach ridge sand deposits, mined for construction aggregate, are highly variable. Rinker Materials utilizes a small reverse-circulation drill rig to prospect and profile unconsolidated fine aggregate deposits more effectively and inexpensively than other drilling methods. Sample data is stored in a spreadsheet that calculates yield and volume. Rinker also uses a Trimble ProXR backpack GPS to locate boreholes in the field, track mine progression on a monthly basis, and to map restrictive features such as wetlands. Autodesk Land software is used to create detailed deposit maps and mine plans. Rinker believes that these practices have led to improved awareness of deposit characteristics and deposit utilization.

Jan 1, 2004

By D. A. Elgillani

Oxidation potentials have been measured in the presence of various concentrations of cyanide, ferrocyanide, and ferricyanide and ethyl xanthate at various values of pH and related to flotation response. Eh-pH diagrams are constructed and show that the formation of surface ferric ferrocyanide is probably responsible for depression when cyanide is added. The influence of cyanide in the depression of pyrite with xanthates as collector has been the subject of many investigations (1,2,3,4,5,6), and from these studies several theories on the mechanism of depression have evolved. Wark and Cox (7) and Gaudin(8) have suggested that the depressing effect is due to a competition of cyanide ion with xanthate ion for the surface. Cook and his colleagues (9,10,11) have explained this phenomenon in terms of competition between hydrocyanic acid and xanthic acid. Sutherland (12) has shown that both of these theories describe accurately the relation between pH value and cyanide addition at constant collector addition but fail to describe the relationship, between pH value and the amount of collector required to cause flotation. Taggart(12) suggested that depression in these systems is due to the formation of a reaction product between ferric ion at the pyrite surface and ferrocyanide ion derived from solution. Majumdar(4,6) has attempted to prove this hypothesis by measuring the contact angles of pyrite in the presence of 25 mg/liter ethyl xanthate and different concentrations of potassium ferrocyanide and ferricyanide. In all cases the contact angles were quite high up to pH 10; these results indicate that pyrite should not be depressed by either potassium ferrocyanide or ferricyanide. In view of these facts, Majumdar has assumed that the compound Fe(CN)2 forms at the surface.

Jan 1, 1968

By Ronald L. Wiegel

The United States produces approximately 40 mil- lion tons of phosphate rock per year. Most of this rock is converted to diammonium phosphate and used as a fertilizer component for the domestic and international agricultural market. Much of this phosphate rock production is concentrated in the southeastern United States, with about half coming from washing and screening operations and half from flotation separation from sand and clay. This paper summarizes current operating practice in the industry and touches on some of the emerging technologies required to solve the problems associated with a diminishing high- grade reserve and the need to implement dolomite/francolite separations on a commercial scale.

Jan 1, 1999

By M. Lonoff

G. Campbell The paper by M. Lonoff looks at the importance of byproduct prices on copper production. The paper develops several interesting points on this topic, but there are some points in the theoretical discussion that could use further development. A couple of these theoretical topics will be considered here using the paper&apos;s framework of assumptions without concern about how realistic the assumptions are for the copper industry. Lonoff&apos;s theoretical model is based on a static, homogenous world where all copper/byproduct deposits are identical, and these deposits are the main source of these metals. Due to the importance of the byproducts to the production decision, the term coproducts will be substituted for the term byproducts to reflect more accurately this condition. The conclusion is drawn that a rise in coproduct prices necessitates a decrease in copper prices because copper production is increased as a consequence of increased coproduct production. The observation that real world behavior does not always follow this pattern is dismissed as "speculation." However, it can be easily shown that within this simple framework market forces might create the observed behavior. The key question to be answered is what causes coproduct prices to rise. Three possible cases will be used as illustrations. The first case is the one implicity assumed by Lonoff. Here, the demand for coproducts increases at all prices (an outward parallel shift of the demand curve) with the demand for copper remaining constant. As reported in the paper, the results are higher coproduct prices, an increase in coproduct production, and lower copper prices due to the resulting increase in copper production. The second case is when the supply of coproducts are constrained-leading to higher market prices. Copper production, as required by the simple model, is also reduced which Reply by M. Lonoff Campbell&apos;s comments give me an opportunity to clarify a few points in "Copper and Its Byproducts." That paper examined the affect of byproducts on the copper market and considered the relative riskiness of multi-metal deposits from an investment standpoint. That brief note made no attempt to be exhaustive. Nevertheless, Campbell&apos;s comments miss the point of the paper and necessitate a response. My "theoretical model" was static and I freely conceded after introducing the assumption of identical deposits that "none of the assumptions hold." These simplifying assumptions allowed me to bound the possible effects of higher byproduct prices on the copper price by assuming identical deposits and computing average price effects. I took great pains to subsequently explain that since deposits are not identical the identity of the marginal deposit might change due to byproduct price changes. In this case, average price affects will overstate the affect of byproducts on copper prices. According to Campbell, I dismiss as speculation any "real world behavior that does not always follow this pattern" (of metals prices moving in opposite directions). In the byproducts paper I noted that gold, copper, and silver price movements often parallel each other on an intra-day or day-to-day basis. Such movements are largely due to market anticipation of or reaction to changes in interest rates that affect carrying costs of metals stocks. Other movements may be due to anticipated changes in available supply or physical requirements. I loosely grouped these effects as speculative. To distinguish this statement from the main thrust of the paper, I contined "In the long run if gold and silver prices remain high the equilibrium copper price will be lower." The paper set out long run equilibrium conditions rather than attempting to explain price movements on a daily basis or on a year-to-year basis.

Jan 11, 1983

By Delon Hampton, Francis K. Mensah-Dwumah

INTRODUCTION The state-of-the art in the area of soil-structure interaction is not sufficiently developed that one can accurately predict the earth load distribution on buried structures. This lack of knowledge has led to the use of high factors of safety in their design and conservative assumptions for the loading diagrams. As a step towards the improvement of the design methodology for buried structures, it is important to be able to apply new analytical techniques and monitor the performance data obtained on full-size buried structures. The performance data should preferably include: 1) the actual stress distribution on the buried structure, 2) stress distribution in the buried structure and surrounding soil media, 3) vertical and lateral movements in the soil adjacent to the buried structure, and 4) deflection of the buried structure. Brown (1967), Davis (1972), Krizek, et al (1974), Krizek and MacQuade (1978), and some few others have compared the performance of full-size culverts with finite element results. Despite all these efforts, a complete understanding of the soil-structure interaction problem has not yet been fully achieved. In an effort to make improvements in the existing design procedures for buried structures constructed in an open-cut, the Department of Environmental Services (DES), Washington, D.C., in conjunction with Howard University, undertook a detailed study of Section II of the Capitol Hill Relief Sewer (CHRS). Inclinometers were used to measure lateral movements of the excavation wall and the total normal interface stresses acting on the concrete sewer were obtained using glotzl total pressure cells. This paper describes the results of the field instrumentation program for acquisition of data, their comparison with the design assumptions, and the results of a series of post-construction finite element analyses of the CHRS project.

Jan 1, 1979

By C. D. Secrest

Visiting Spring Canyon, a historic coal mining district near Helper, Utah, I was impressed by the great accomplishments that had taken place there. A tour book of the region tells of a period that began in the early 1900&apos;s, when the land was still very much the Old West, when settlers lived out their lives in coal company towns and produced a resource that was to build a nation (Cunningham, F., 1990). Between 1912 and the early 1970&apos;s, 11 mines had come and gone in that narrow canyon less than 15 kilometers long. Spring Canyon is a historic district now, but I could not dwell too long on the richness of its history. I was there to look for evidence of PCBs.

Jan 1, 1993