Search Documents

By J. S. Hattrup

INTRODUCTION Tunnel boring machines in non-abrasive competent rock with little or no water have set new performance standards in the driving of tunnels. However, when the machines have hit blocky or running ground, they have encountered difficulties. The success of a tunnelling machine is usually due to a thorough geological investigation which accurately describes the rock conditions, a well designed tunnel support system, and a tunnel boring machine designed to cope with these conditions. In some cases machines have had to be modified in the tunnel after the machine had commenced boring, because geological conditions were not correctly anticipated before tunnelling began. The features described herein are not a panacea for all conditons, and some of them, like an auxiliary thrust system that thrusts off a precast invert segment requires pre-planning of work on the part of the contractor. CUTTERHEAD DESIGN Figure 1 shows typical cutterheads of ten to fifteen years ago. Note the large buckets and large openings between the buckets. These large openings were considered necessary to gain easier access through the cutterhead for cutter changes. The standard cutter in those days was an 11 inch or 12 inch cutter with small bearings, and was generally a delicate tool for the duty it was to perform. These large buckets would clog up if a formation with clay seams was

Jan 1, 1981

By B. J. Arnold

Coal blending inherently means homogenizing a mixture of coals so that the properties of the blend meet some specifications for maintaining power plant performance and emission requirements. In practice, however, coal blending is, at best, coal mixing. The degree of blending sophistication required depends on the reason for coal blending in the first place. If it is to maintain fuel characteristics that will diminish the chance of slagging and fouling, then some swings in variability may be tolerated at some power stations. However, if emissions limits are the issue, then more sophistication may be needed. Emissions limits are becoming stricter with requirements to meet averages for shorter time frames (hours and days instead of weeks and months). These restrictions require closer control over the quality of the blend being fed into the bunkers at the station. Even scrubbed units should have a consistent quality of fuel as feed so that sorbent additions can be minimized. To meet these challenges, engineers must consider available equipment and control techniques and the properties of the parent coals when evaluating new blending systems.

Jan 1, 1994

By T. F. Deems

The nature, usage and comparatively rare occurrence of ball clay is described. The importance of these white firing plastic clays in ceramics, particularly in the production of industrial sanitary ware and tiles, is emphasized. The US deposits are briefly discussed. What is known about relevant deposits in Brazil, Argentina, Colombia and Venezuela (the four largest ceramic producers in South America) is also described. The ceramic plants have been sited near the centers of population rather than the plastic clay deposits. At present, extraction is probably concentrated on surface residual deposits and lenses which require minimum investment. Native plastic clays are used exclusively in the tile plants, but in sanitary ware, they are often used as extenders of imported ball clays.

Jan 1, 1997

By James S. Browning

The principal uses of fine ground mica are as filler in wallboard joint cement, as a filler and surface coating for roofing, as an ingredient in paints, and in oil well drilling mud. The mineral has other uses in the manufacture of rubber, wallpaper, plastics, welding rods, electric insulation, house insulation, and textiles, and as an annealing agent in metal treatment. In recent years, more than 999 percent of the domestic mica produced has been scrap and flake mica (mica which does not meet specifications for sheet mica and is used for producing fine ground mica). There has been a continued increase in mica production for, several years, the 1963 production of scrap and flake mica totaling 117,251 tons.

Jan 1, 1966

Eldorado Resources Ltd.(ERL) uses a solvent extraction process for the processing of uranium ores. The solvent extraction plant consists of 4 extraction and 5 stripping stages with regeneration carried out as required (Wyper, 1982). Extraction is carried out with a solvent consisting of 4.5 vol % Alamine 336, 4.5 vol % Isodecanol and 91 vol % kerosene. The extraction step can be represented as In equation (1).

Jan 1, 1988

By J. Paul

Mining engineers in charge of open pit mine planning very often face decision making situations dealing with the selection of the most economical method for the removal of overburden. Ripping versus conventional drilling and blasting are the options considered. The choice of a particular overburden removal method depends upon the physic-mechanical properties of the overburden material as well as the various cost factors involved in the process. The analysis of techno-economical factors involved in different methods of overburden removal needs detailed study and investigation by a technical expert. But the expert system "Fragmentation System Design" has been created in a way such that it will help and expedite the decision making process relating to overburden removal in surface mines. Furthermore, this expert system can be used for detailed design aspects of overburden removal in open pit mines.

Jan 1, 1988

The paper describes the procedure of data inquiry on the structure of mineral production in Austria and selected results. Goal of the endeavor was to gain more tangible insights into the mining industry as a basis for regulation balancing economical, ecological and social aspects.

Jan 1, 2006

By J. Craig Green

Companies mining for coal, oil shale, and minerals in the western US must often complete extensive geotechnical studies to satisfy federal and state regulations. The modern mining process is further complicated by the legal problems and liabilities associated with mineral rights and land leasing. Yet the study of water rights-unique to the West is often incomplete or ignored until the latter stages of mine planning. Water rights in the West are not adequately understood by many mining companies and their geotechnical consultants. Some firms, headquartered outside the western US, have not had to contend with the water supply problems of a semi-arid region. Water problems encountered by eastern mining companies, for example, are primarily water quality, drainage, and flood control. Even when water quantity is a problem in these areas, ownership and/or use of it is governed by entirely different legal and administrative concepts than in the West. Both legal and engineering issues have to be considered when studying western water rights. Legal issues, such as existence and title, must be addressed to insure that a particular water right is properly established and maintained. The exercise of a water right, however, often requires engineering analyses that focus on preventing injury to the properly established water rights of others.

Jan 8, 1981

By R. Allan Wallis

In the past mining engineers have tended to rely heavily on the advice of fan manufacturers in relation to fan equipment issues. A more adequate approach was advocated in a paper [ Wallis, 1965 ] submitted to the Eighth Commonwealth Mining and Metallurgical Congress held at Surfers Paradise, Australia during 1965. At that time Mount Isa Mine were in the process of installing 3 large 6096mm (20ft) diameter vertical axial flow surface fans of an advanced type [ Mathews et al, 1967 ]. The preliminary feasibility studies prior to preparing the detailed job specification for this project were extremely thorough with the result that it was possible to include detailed information and instructions in the document, ensuring the procurement of equipment that was satisfactory in all respects. Full advantage was taken of expert services provided by external organizations during the large coordinated multi-disciplinary exercise. My continuing activity and development in relation to the technology of axial flow fans is now at a stage where all known design and performance data are accessible through CAD programs [ Wallis and Kipp, 1987 ]. The extensive calculations that were necessary in 1983 can now be carried out in a mere fraction of the time, and with complete confidence. Model testing in order to validate the fan and duct design proposals is, in my view, no longer essential. The first of the computer programs enables a mine ventilation engineer to study a large number of alternative axial fan arrangements for comparison with the centrifugal alternative. By entering the volume flow rate, fan pressure and air density, he can then with ease, and rapidly, investigate the effect of various blading arrangements, downstream evasee area ratios, and hub ratios, on fan diameter and speed, with their related attainable fan efficiencies. This procedure had its origin back in the 60s when I was advising mining companies on new fan equipment. At that time such an investigation was quite lengthy and lacked the precision and completeness that is now available within the present programs. To obtain the major benefit from these outputs, it is most important not to be disconcerted by the three very important nondimensional parameters, namely, the tip flow coefficient (LAMt), the fan pressure coefficient (Kt or Kit), and the swirl coefficient (Es and/or Ep) as these are important when assessing the various design proposals. When seeking an understanding of the role and importance of each of these variables, ample help is provided in the user manual; the design recommendations are summarized in the help screens which are readily accessible within the design programs.

Jan 1, 1989

By S. W. Asihene, K. Osseo-Asare

The leaching and solution treatment operations used in the ammoniacal treatment of laterites depend on the ability to establish and maintain close stability relations between soluble metal ammine complexes and solid phases such as oxides, hydroxides, basic carbonates, sulfides and ammonium double salts. This paper presents a quantitative treatment of heterogeneous equilibria in ammonia/laterite hydrometallurgical systems, by means of several.types of hydrometallurgical phasedia- grams (e.g., Eh-pH, log [NH3 + NH4+] - pH, log [C02] - pH, log SO42-] - pH, log [Metal] - pH). Dissolution/precipitation phenomena associated with nickel and cobalt recovery and with magnesium scaling are discussed in the context of the phase diagrams.

Jan 1, 1979

By Robert L. Wade

The two primary goals in underground coal mining are to improve safety and to lower mining costs per ton through increased productivity. However, as evidenced by the drastic decrease in. productivity since the enactment of the 1969 Coal Mine Health and Safety Act, (the Safety Act), these goals appear to be mutually exclusive. Millions of dollars have been spent in the res, arch and development of systems to solve this problem. Before the Safety Act, "productivity had experienced a 25-year history of continued increases ...? (Douglas, 1980). But since its enactment there have been dramatic decreases in productivity accompanied by phenomenal increases in mine costs. Labor trends, depletion of the more readily minable underground coal reserves and other factors have contributed to this situation, but the dominant factor is undoubtedly the Safety Act itself. To illustrate, prior to 1969 underground coal mine production was much greater than surface mine production but since then underground mine production has been declining at a rate greater than the overall growth rate of total coal production.

Jan 1, 1985

By M. Kockler, S. J. Jung

Underground operations at the Rain Mine averaged 360 tonne/day (400 ton/day) utilizing underhand drift-and-fill and longhole stoping with delayed fill between 1993 and 2002. Mining from four ore zones produced over 803 800 ore tonnes (886 000 tons) at a grade of 9.32 gm/tonne (0.270 oz/ton). Even though openings in the ore could be as large as at 9 m (30 ft) wide, 30 m (100 ft) high, and over 60 m (200 ft) long, the weak rock surrounding the ore zones restricted development size to 3 m (10 ft) wide by 3.7 m (12 ft) high.

Jan 1, 2004

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By Tom Bruington

This paper discusses the accuracy of determining the quantities of gold and silver on activated carbon in various stages of process for typical precious metals flowsheets. Accurate plant performance evaluation depends upon reliable estimates of carbon and precious metals inventories. The sources of sampling error are identified and methods of reducing them discussed. Several case studies illustrating the sensitivity of flowsheet performance to sampling error are presented.

Jan 1, 1991

By R. Matikainen

Since the Brundtland Commission in 1987, the use of natural resources has been an issue of global concern. Minerals are among the most important Earth resources and will definitely be essential for the development of societies also in future. Increasing scientific effort is needed not only to discover new deposits, but also to promote resource management in ecologically and socially sound way. Sustainable resource management is essentially a multidisciplinary challenge of developing life-cycle analysis and recycling of non-renewable resources from local to global scale. It offers great opportunities for geological surveys not only in EU, but all over the world to contribute positively to the welfare and sustainability of societies.

Jan 1, 2003

By H. J. Bogert

Shallow, gently dipping quartz veins at the Mineral Hill Mine are mined in room and pillar stopes. Ore zones are severely folded and fractured, thus actual pillar strength and physical properties of the rock mass deviate significantly from conventional laboratory tests and pillar theory. Laboratory specimens large enough to include pre-existing fractures proved to be representative of actual pillar strength. Further adjustment for specific pillars was based on RQD. Deformation and stress were measured in several pillars during pillar recovery. Stress data and finite element modeling were used to estimate absolute pillar stress at failure. The stress/strain relation provided an excellent indicator of pillar behavior. Good agreement between lab data and underground data was found.

Jan 1, 1995

By V. Galla

In the present paper, two large diameter columns 2 m tall and 1.3 m diameter filled with crushed (finer) and run off mine (coarser) heap leach materials respectively were used to perform unsaturated flow studies. Instruments measuring moisture content and matric suction were placed in the columns at different depths as water was applied at calibrated flow rates from the top of the columns. The outflows from the columns were recorded using tipping bucket rain gauge placed at the bottom of the columns. Unsaturated hydraulic parameters were also obtained for the heap leach materials, scalped (passing 4.75 mm sieve size) and whole (passing 37.5 mm sieve size) sample. The measurements obtained from the columns were later compared with unsaturated flow modeling results. The comparison indicated sensitivity towards the sample size selection for unsaturated hydraulic parameters, and initial conditions considered in the model.

Jan 1, 2009

By D. Buranek, J. G. Wulff, F. W. Gifford

I. INTRODUCTION During the past few years, the state of the art of disposal of solid and liquid waste products from uranium mining and milling operations has experienced some rather interesting and significant changes. Some of these changes have resulted from technological advances in the milling operations and in the engineering aspects of the actual design and construction of the disposal facilities. However, the most significant changes, at least those which have had the greatest impact on the comparative cost and economics of modern disposal systems, have been environmental requirements and regulatory controls, which have become increasingly stringent in recent years. Without delving into the details of the myriad of new laws and regulations which now control the uranium industry, it can be stated with reasonable confidence that one of the principal purposes of more rigid state and federal controls over this industry is the basic desire to promote safer, more reliable and longer term means of effectively controlling and disposing of the potentially objectionable waste products resulting from uranium mining and milling operations. It is difficult to take issue with these basic goals because their need was spawned by past lack of awareness and inattention on the parts of both government and industry to the long term environmental problems and potentially hazardous conditions which can be created by limited planning and ill-conceived or poorly controlled and executed disposal practices. On the other hand, despite the good intentions of those who developed and those who are administering the regulatory controls now in effect, the basic danger exists that overgeneralization of the approach to disposal problems and overrestriction of the potentially acceptable solutions for uranium mine and mill waste disposal could have a significant, adverse economic impact on the mining industry and the ultimate consumers of their products. The regulatory pendulum, which perhaps swung too far toward lack of controls over uranium mill waste disposal in the 1940's, could now well be headed too far in the opposite direction, that is toward over-regulation in the form of restrictions based on technically unrealistic or weakly supportable

Jan 1, 1980

By Shulin Xu, Moreno Pescara, Nicola Avagnina, Piergiorgio Grasso

The Roreto Tunnel is a shallow, twin-bore, road tunnel on the connection between the A6 and the A21 motorway in NW Italy. The challenges faced the design and construction of this tunnel derive from 1) the presence of groundwater, both phreatic and artesian; 2) excavation in loose and/or little cohesive materials; 3) excavation in cohesive materials containing water-saturated, sand lenses; and 4) surface constraints due to the urban environment. In this paper, these problems are examined and the rationale led to the optimum design choices and construction solutions explained. The experience should be useful to others when tunneling in similar situations.

Jan 1, 2003

By J. Leinart

As is readily apparent, the reliability of the early-stage costs estimated for any mining project are critical to the viability of that project. An estimate too high might leave a potentially profitable deposit undeveloped or worse yet, available to a competitor. One too low might waste investment dollars in a project not yet economically ripe. There are two aspects critical to any estimate: 1. The cost data used to represent the values of the wages, salaries, supplies, and equipment. 2. The design used to determine the engineering parameters upon which the above estimated values are based. Given that all of the information contained in Mining Cost Service is provided by suppliers, equipment manufacturers and mine operators, one wonders why there is any question as to the reliability of cost estimates developed using this information. Given that it is all actual (as opposed to statistically derived) data, where do the problems with estimate reliability lie and what is the impact of the data on that reliability? The following presents a series of analyses designed to assess the reliability of the cost estimating process. Both the actual cost data and the engineering parameters upon which they are based are examined in an attempt to quantify and understand the importance of each. While several sources of cost information are available (Means, Richardson, Primedia?s Equipment Watch, and individual suppliers and manufacturers), the following rely solely on data contained in InfoMine USA, Inc?s, Mining Cost Service and in its Sherpa Mine Cost Estimating Software.

Feb 27, 2013