Search Documents

By Jurgen H. L. Stuve, Rick E. M. Widelski

Any one who has been involved with the mining or the treatment of gold-bearing ores will agree that at the end of the total process, the quantity of gold recovered is never as much as was expected. These short falls are usually explained away by claiming that:- the original evaluation of the ore being mined was inaccurate the plant treatment process is not at its optimum theft is taking place excessive dilution occurs during mining The truth of the matter is that the gold is being "lost". During all the stages of its production, starting from the mining, right through to the smelting process, a certain amount of gold is not recovered. When a newly found gold deposit is being evaluated and the drilling data being analysed, cautionary factors are applied so that the grade is not over-stated. Once the decision has been taken to start mining and development is in progress, the exposed ore is sampled. When Again, when this data is being analysed more safety factors are used to ensure that when a piece of ground is given a block-value, the gold content is not over estimated. mining actually takes place and the ore transported to the plant for treatment, the metallurgical department also introduces certain safety factors when predicting how much gold will be recovered. This shows that the quantity of gold that one expects to finally recover is already a conservative figure. The actual quantity recovered invariably falls short of this figure, in fact, South African gold mines are satisfied when achieving a Mine Call Factor (MCF) of 85%. In the last few years a great deal of work has been carried out to investigate how this unaccounted for gold is lost and what steps can be taken to remedy the situation. Previously mined areas were re-swept using the traditional hand brush method; experiments were carried out with water jets sometimes in conjunction with compressed air and even small portable vacuum cleaners were tried. None of these methods were totally successful in recovering the left over gold but the use of vacuum systems showed the most potential. the In South Africa this has resulted in introduction of high-powered vacuum systems on the gold mines to suck-up this lost gold. These were initially introduced in the mining areas, particularly old areas, to recover any left over ore. The results proved extremely profitable, So much SO that presently, well over 120 suction systems are doing this type of work. This success encouraged plant operators to look at areas of potential loss in the plant itself. This has resulted in an increasing number of machines being supplied to gold plants mainly for clean-up applications with the bonus that the material sucked up invariably contains gold.

Jan 1, 1993

By Ian Mcgaffin

P.T. Kellan Equatorial Mining (KEM) is an Indonesian incorporated company owned 90% by CRA Limited of Australia and 10% by PT. Harita Jayaraya of Indonesia. The Kelian gold mine first commenced production in January 1992 and has produced in excess of 21 tonne of gold (675,000 oz) in its first 18 months of operation. The operation is a large tonnage low grade deposit that accepts a low gold recovery by industry standards due to the partially refractory nature of the orebody.

Jan 1, 1993

By Dennis J. Appelhans

Lac Minerals Bullfrog conducted research and testwork to find an environmentally acceptable alternative to lead for fire assaying. The result of this work was the substitution of bismuth for lead in all fire assaying performed at the Bullfrog Mine. The environmental and economic ramifications of this discovery are highlighted.

Jan 1, 1993

By Gary L. Simmons

Aqueous pressure oxidation at low temperature, although desirable from a process engineering and operations point of view, presents unique problems when temperatures approach 160°C (320°F). In developing the pressure oxidation process for the Lone Tree Mine, elemental sulfur formation and agglomeration with pyrite proved to be a problem. This paper discusses some of the unique mineralogical and chemical characteristics of the Lone Tree sulfide deposit that make it amenable to low temperature pressure oxidation. Problems encountered during pilot plant operation and their solutions are also discussed.

Jan 1, 1993

By Yeonuk Choi, Gus Van Weert

cyanide control in effluents is becoming a critical environmental issue for the gold extraction industry. Silver impregnated carbon removes free cyanide effectively to the ppb level from solution in high throughput columns. By re-calcining the cyanide saturated carbon, the impregnated silver is restored to activity and the cyanide destroyed outside the effluent stream. Many gold mills already have an activation kiln on site, which could make retrofit relatively easy.

Jan 1, 1993

By Eric Jones, Leslie C. Thompson

Biological processes for cyanide detoxification in mine waste are receiving attention as an alternative to conventional chemical treatment options. Some of the advantages of biological treatment include: Low comparative treatment cost * Shorter treatment time * In Situ Treatment * Complete Detoxification - Ends long-term liability - Eliminates in-perpetuity monitoring - Natural Re-Vegetation potential Natural and non-toxic nutrients, by-products and process end-products Hecla Mining chose a bio-neutralization process developed by Pintail Systems, Inc. for cyanide detox in spent are and process solutions from heap leach operations at the Yellow Pine Unit. The Yellow Pine operation is located 50 air miles east of McCall, Idaho, in the Stibnite Mining District. This district is a historic mining district dating back to the early 1900's. During World War II, this district produced a majority of the antimony and tungsten the United States using for the war effort. More recently, the Stibnite district has been known for its gold production. Hecla Mining Company is based in Coeur d'Alene, Idaho, and is a leading domestic producer of precious metals and a major supplier of specialty aggregate and industrial minerals. Pintail Systems, Inc. is a company specializing in the development of biological treatment processes for mine waste remediation. PSI has offices in three states and a laboratory, pilot plant and field office in Aurora, Colorado

Jan 1, 1993

By G. M. Bernard

This paper provides an overview of the various methods and techniques for transporting and stacking ore on heap leach pads. Towards this end, brief discussions of the various methods and techniques important to this process are presented.

Jan 1, 1993

By J. M. W. Mackenzie

Three major developments have dominated the recovery of gold from ores, viz; 1846 Elsner's studies of gold solubility in aerated alkaline cyanide solutions 1887 MacArthur and Forrest's process based on zinc precipitation 1980+ Large scale development of the CIP process The brevity of this list for a metal whose extractive metallurgy has been as widely studied as any metal reflects the fact that the chemistry of the gold recovery process, as opposed to the engineering has seen few significant breakthroughs in over a century of application. to The purpose of this paper is introduce a new chemistry for gold recovery which may, in the future, add significantly to the technology of gold recovery. This new chemistry is based guanidine functionality - (R2R2N) 2 C = N R2 on the In developing the use of the guanidine functionality for the recovery of gold as the aurocyanide anion from leach solutions and pulps, Henkel has, as its objective, the development of an effective gold selective ion exchange resin. As will be seen, the initial investigation of the properties of the guanidine functionality in the solvent form for gold recovery lead to some significant metallurgical developments of their own but, the foremost objective was, and remains, the development of a resin for gold recovery. As a part of this development project, Henkel has entered into association with Mintek, South Africa, and this ongoing association has the potential to develop RIP/RIS technology for the gold industry. More details on Henkel's gold recovery technology and Mintek's role in this programme are given in (1). an The application of ion exchange resins to gold recovery is not new and many reviews have been published on the advantages of this process, and on the current state of the art of gold recovery by ion exchange resins. (2)(3)(4) Widespread application of ion exchange resin based processes for gold recovery has, however, not occurred to date. Fleming and Cromberge (5), described some significant pilot plant RIP trials in South Africa and the partial success of these pilot plant trials held out the tantalising possibility of a breakthrough in gold recovery based on RIP technology. Despite this pioneering work, only two really significant applications of RIP technology for gold recovery exist today. These are the Golden Jubilee Plant in the Eastern Transvaal South Africa and the widespread, although in some respects technically backward, use of ion exchange for gold recovery in the former USSR. There are two main reasons for the current scarcity of RIP and RIS plants used for gold recovery. These are: 1. 2. The perceived problems of engineering RIP plants The lack of a resin having suitable chemistry for both gold loading and gold elution The problems of engineering RIP plants have been largely overcome in the last 25 years. Much of the development in RIP plant design took place in the uranium industry during the rapid expansion of that industry in the mid 1970's. In addition, the development of CIP engineering systems has lead to the development of in-pulp solid extractant based metallurgical plant designs which can, with limited modification, be adopted to RIP. The lack of a resin having suitable chemical properties has almost certainly been the main reason for RIP/RIS not being introduced into the gold industry over the past decade. Attempts to use RIP/RIS have focussed on either conventional we ak base or conventional strong base resins. The weak. base resins have the disadvantage that they

Jan 1, 1993

By A. Nieto

This article is a review of previous discussions about underground mining method selection and classification with the purpose to clearly define and classify the two groups of variables (indicators) involved in the mining selection process: key deposit indicators (KDIs) and key mining method indicators (KMIs). This paper provides a simple and clear approach for the classification and selection of a feasible underground mining method based on a predetermined set of favorable deposit characteristics, which are defined as key deposit indictors (KDIs). This article also gives a summary of the key advantages and disadvantages associated with every underground mining method based on their key mining indicators (KMIs). The selection method given in this paper is based on defining field KDIs and comparing them to the KDIs that are favorable to every considered mining method. By cross validating a matrix of favorable KDIs, the paper presents a simple approach to rank several underground mining methods using a scale from favorable to less favorable accordingly to the ore deposit characteristics (KDIs). KMIs are used to further complement KDI rankings by analyzing every method’s KMI performance based on the expected productivity of the mining operation being considered. To further assist the reader through the selection process, this paper gives basic sketches representing each of the primary underground mining methods discussed in this paper. Each method is given using the same 3D isometric view as spatial reference to assist the reader with visual interpretation and comparison between methods.

Jan 1, 2010

By S. Peng, Yi Luo

Subsurface strata movements and deformations associated with underground longwall mining activities could cause certain influences to subsurface structures and water bodies. Methods have been developed for the prediction of final and dynamic subsurface movements and deformations induced by underground longwall mining operations in the eastern coal fields. Two new types of strata deformation, vertical and total strains, which could be useful in the field of subsidence research in assessing subsidence influences to the subsurface structures and water bodies, have been introduced. Using the subsurface subsidence prediction model, three types of subsidence influences to surface and subsurface hydrological systems have been identified. Attempts have been made to quantify the two types of subsidence influences that could cause water loss and could lower water levels in aquifers.

Jan 1, 2010

By M. E. Buzon, M. E. Gunter, B. D. McNamee

A Google search on talc asbestos yields more than 500,000 hits due to the growing number of civil lawsuits in this area. Historically, the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos and whether the amphiboles had an asbestiform habit. Ultramafic-hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc, but they can occur in the surrounding black-wall. In these deposits, the serpentinite host rock is in direct contact with the talc, therefore, allegations can be made that non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. We analyzed talcs from both metamorphosed carbonate- and ultramafic-hosted talc deposits using polarized light microscopy (PLM), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), electron microprobe (EPMA) with wavelengthdispersive spectroscopy (WDS), transmission electron microscopy (TEM) with EDS, and powder X-ray diffraction (XRD). Compositions of minerals determined by EDS alone are not sufficient to confidently identify asbestos, despite common practices by some researchers. We emphasize, using both historical samples, and analyses of currently contested minerals, the importance of determining both the structure and composition of a mineral, as well as defining its morphology, before concluding whether it is asbestos.

Jan 1, 2018

By C. J. Bise, P. Bucks

Central Appalachian coal reserves are a valuable natural resource in high demand, both domestically and internationally, justifying efforts to increase percentage recovery through pillaring. Unfortunately, the challenge associated with pillar extraction introduces additional safety risks during the activity. Although pillaring developed prior to mechanized mining, current technology and mining practices have made this form of mining highly modernized. However, current fatality trends suggest that work still needs to be done to control the residual risk that is not controlled by modern practices, such as those having a personnel-performance-based component. This paper investigates the application of modern coal pillaring techniques and will present a risk-management-based strategy that targets personnel-performance-based risk, in order to improve the ability of safety engineers, managers and trainers to provide training programs addressing the needs of pillaring sections.

Jan 1, 2012

By L. S. Gertsch, M. Z. Abu Bakar

Linear cutting tests of a porous sandstone with a radial drag pick show that saturation of rock with water can increase the specific energy of fragmentation. This appears to be due, in this case, to a saturation-induced increase in the forces acting on the cutting tool without a concomitant increase of the fragmented volume. The mechanisms of this reaction are explored by examining various responses of the parameters controlled and induced during the linear cutting tests, such as cut spacing, cutter penetration, three-dimensional forces and muck production. A program of load-indentation testing is underway to evaluate the permeability threshold of this behavior. These findings are opposite from those made when the same rock is cut with a constant cross-section disc cutter reported elsewhere (Abu Bakar and Gertsch, 2011). Such results highlight the effects of different cutting tool designs, and indicate the need for a well-coordinated program of research to support effective excavator design and selection.

Jan 1, 2012

By R. H. Grau, C. D. Taylor, A. L. Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Mine Improvement and New Emergency Response (MINER) Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the National Institute for Occupational Safety and Health (NIOSH) Bruceton Experimental Mine was pressurized using a 1.1-m (42-in.) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By J. Brune, P. J. Coleman, L. Martini

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners’ activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly understand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985. This report describes an alternative method of analyzing and presenting MSHA data for the purpose of identifying high-cost, high-severity injuries and illnesses. Researchers at the NIOSH Spokane Research Laboratory (SRL) developed programs to find the top five most frequent accident classes, natures of injury, types of accidents and other selected variables from the MSHA database. Studying these variables gives a cross-sectional snapshot of the most frequent groups of injuries within a commodity, regional group or time period, and allows researchers to quickly understand developing patterns for new research projects. The primary benefit of this approach is to

Jan 1, 2009

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By J. L. Hoover, P. W. Conrad, J. Downey, S. Parrow, S. Rosenthal

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect drill bit wear and use that equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel software package. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015