Search Documents

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

By R. Lawrence

Mineral property valuations to be used for Canadian securities regulatory purposes must comply with CIMVal1. The technical basis for a CIMVal report is the same as that required for a technical report that complies with NI 43-1012. NI 43-101 describes the content to be covered in a technical report, while also covering other requirements, one of which is that the report should be based on a property visit. CIMVal is based on five tenets that the valuator must follow: ? Materiality. ? Independence. ? Transparency. ? Competence. ? Reasonableness. Upon its adoption by CIM Council in 2003, it was hoped that the new CIMVal code would be adopted without change by the several Canadian regulators.

Jan 1, 2011

By T. R. Ellis

Minerals Appraisers/Valuers often find great difficulty or failure in attempting to employ the Sales Comparison Approach to the Market Value Appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income producing property. Common criticisms of the sales comparison approach by minerals appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the Income Approach are usually derived by minerals appraisers, and by review of some conspicuous examples of the much too common misuse or abuse of the income approach in market value minerals appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables (see APPENDIX). The examples are used as the basis for discussion of ways to employ adjustments for operating economics and many other factors, while cautioning about the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

By B. A. Osei

Research to evaluate possible metrics for predicting dredgeability of compact aggregates, by hydraulically actuated clamshell dredges, shows work done by the pistons as a viable metric. Analysis of field data shows that there is a low, positive, correlation between cycle time (CT) and work done. If this correlation exists, then CT has to be considered an independent variable affecting work done during dredgeability assessment. Further research is required to elucidate the relationship between CT and work done during dredging. The objective of this paper is to test the hypothesis that work done during dredging increases with increasing CT. Kinematics and dynamics of the hydraulic clamshell were modeled and implemented in Simulink® in MATLAB. The model was validated using field data. The model was then used to test the research hypothesis. The results show that work done increases with increasing CT. This work confirms that work done during dredging increases with increasing CT. This result indicates that though an operator can increase the CT to deal with difficult digging, inputting unduly high CTs results in higher energy consumption during dredging.

Jan 1, 2011

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By B. Anameric

Considerable effort has been directed towards understanding the carbothermic reduction mechanisms of self-reducing, fluxing dried green balls to produce pig iron nuggets. Given the geometry of the situation, some investigators believed that the shrinking core model was applicable. Hence, this study involved investigation of the applicability of the shrinking core model to pig iron nugget production. The experiments involved heat treatment of dried green balls utilizing either a laboratory-scale resistance box furnace or a gas-fired muffle furnace at various furnace temperatures and residence times. The products were analyzed for the following: (i) preferred reaction pattern, (ii) distribution of the metallized areas, (iii) % iron content variation in the pig iron nuggets from surface to center, (iv) carburization pattern and (v) physical and chemical properties of the pig iron nuggets. It was determined that the reduction of iron oxide occurred simultaneously throughout the sample and not beginning at the surface and propagating inward; thus the shrinking-core model was not applicable. Heat transfer and gas diffusion from surface to center were not the rate-limiting steps for reduction and carburization reactions.

Jan 1, 2011

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011

By F. Habashi

Chile is at present the largest copper and rhenium producer and was before World War I the largest nitrate producer. She is also an important producer of lithium carbonate and molybdenum oxide. An important event in the history of the country is the Pacific War of 1879-1883 in which she acquired the northern provinces initially belonged to Bolivia and Peru. In 1888 Chile annexed Easter Island. The Chilean mineral and cultural history is briefly reviewed together with the people who contributed to her development. The present report is the result of a number of academic and industrial visits to Chile during the period 1992 to 2009.

Jan 1, 2011

The Virginia Center for Coal and Energy Research has been developing models of wireless signal propagation in underground coal mines since 2007. The current mine propagation modeling software, named COMMS, is able to locate potential broadcast points for underground wireless mesh systems and estimate their coverage. COMMS utilizes programmed routines to calculate necessary values to both quantitatively and qualitatively solve and analyze predicted coverage areas. The program approximates the spatial relationships that are encountered, such as ventilation regulators, belts and other obstructions. Using this model for propagation allows the optimal communications node locations to be calculated, by using lessons learned from current installations and experience with the new technology. In addition, the optimization can be calculated by checking all possible combinations of broadcast locations. This paper compares these optimization calculation methods. The ability to solve a mine?s communication network provides a pre-installation mine network design map, creates coverage maps of the mine and allows planning for future communication activities

Jan 1, 2011

By M. Botz

Alacer Gold Corporation is constructing the Çöpler Gold Mine in eastern Turkey. Mining commenced in the fourth quarter of 2009 and gold production started in the fourth quarter of 2010. The mine is a 15,500 t/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production, but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life, approximately 40 Mt of ore will be placed on the leach pad, which will contain about 35,000 t of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the life of the mine. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By F. L. Pirkle

A heavy-mineral deposit about 1.6 kilometers (I mile) in length and averaging about three meters (10 feet) in thickness is exposed approximately130 kilometers (80 miles) east of Denver, along Interstate 70, in Elbert County, Colorado near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium Ridge. The dominant heavy minerals, accounting for about 70% of the total heavy mineral suite by weight, are ilmenite, garnet, and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan, and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Georgia. Thus, Titanium Ridge provides evidence that heavy-mineral accumulation models for late Cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2011

By V. T. McLemore

Rare earth elements (REE) are becoming more important in our society. REE deposits are found throughout NM. Some REE past production (1950s), as bastnaesite, came from the Gallinas Mountains district, Lincoln County, NM. Several companies and the U.S. Bureau of Mines (USBM) have conducted exploration programs to identify REE potential. Four types of deposits are found in the district: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipe and iron skarn deposits; all are associated with Tertiary peraluminous, alkaline to alkalic-calcic volcanic rocks. District zonation is defined by base metals (REE-F-Cu veins) that form center of the district, surrounded by REE-F veins. The magmatic-hydrothermal breccia pipe deposits form a belt partially surrounding the veins. Iron skarns formed at the top and edge of the trachyte intrusion and are likely the earliest stage of mineralization. In 1991-1992, USBM calculated an inferred resource of 0.487 million metric tons with a grade of 2.95% total REE. With the projected increase in demand of REE, areas such as the Gallinas Mountains district in New Mexico are being re-examined for additional REE potential.

Jan 1, 2011

At long last, mining is on the rebound in Minnesota?s Iron Range and the excitement is starting to show. The SME Minnesota Section?s annual meeting was once again held in the heart of Iron Range country, at the Duluth Entertainment and Conference Center on the Duluth waterfront. The conference boasted a record attendance of 475 people and its largest-ever trade show. Appearances by Governor Mark Dayton?s new Iron Range Resources & Rehabilitation Board (IRRRB) appointee, Tony Sertich, as well as a local Fox news crew (see clip on SME website [link: http://fox21online.com/news/duluth-mining-conference-breeds-optimism-tech-innovation]) made clear that a lot of eyes [ ] are on the industry as it dusts itself off from the 2008-2009 recession. While the early years of the 21st century were very good to the Iron Range, the global drop in commodities prices and production left many companies reeling and brought back bad memories of the collapse of the industry in the 1980s. However, two years of solid growth and a rebound to above pre-2008 production levels have let the Minnesota mining industry to relax a little and talk seriously about long-term growth and stability.

Jan 1, 2011

By S. Khoshjavan

Separation of refractory rock phosphate (P2O5 = 11.5%) from the Dalir area, Iran, containing quartz, calcite and other impurities, by calcination and flotation processes has been successfully used to upgrade the phosphate values. Petrographic studies of this ore showed that collophanite was the major phosphate mineral and the main gangue minerals were calcite, dolomite and quartz. The results of characterization studies showed that the liberation degree of apatite occurred below the average grain size of 140 µm. Preliminary flotation tests were used to process the phosphate samples. Results of preliminary flotation tests showed that they don?t contain any desirable efficiency (grade or recovery) of P2O5. Calcination was the best process for preconcentration of this ore. In the desliming stage, about 14.4% of total P2O5 was removed. Encouraging concentrate grades were obtained after flotation with anionic and cationic flotation, successively. The reagent schemes that have been used in this study consisted of COCO-amine acetate and fatty acid as silicate and apatite collectors, respectively, as well as fuel oil and anionic poly acryl amid as promoter collectors. The optimum pH values for direct and reverse flotations of phosphate were 11 and 6, respectively. Experiments conducted using d80=140 µm deslimed fractions has yielded an acceptable grade of more than 30% P2O5 with a recovery of more than 62%. Finally, a laboratory flowsheet for the processing of Dalir refractory phosphate ore has been proposed.

Jan 1, 2011

By C. Frenzel

Tunnel boring machines (TBM) utilize disc cutters as the primary means for excavating hard rock. Depending on rock excavatability and rock abrasivity disc cutters can exhibit significant wear. A detailed analysis has been carried out to characterize failure modes and wear patterns of disc cutters. The relationship between rock properties, op-eration of the TBM, and failure modes of cutting tools is clearly high-lighted. On that basis a prediction tool for disc cutter consumption has been developed that allows to estimate not only gross cutter life, but accounts for cutterhead design, premature cutter changes, and disc cutter repair costs.

Jan 1, 2011

By S. Frimpong

Shovel excavation constitutes a significant component of production costs in any surface mining operation. This makes shovel loading an important cost center that needs to be improved to lower production costs. Optimization of tool design will improve energy efficiency in earthmoving operations. However, modeling the soil-tool interaction is a complex process due to the fact that forces for excavating particulate material are functions of many variables. The magnitude of this resisting force depends not only on the type of soil but on the size, shape and orientation of the cutting element. Moreover, part of this complexity is attributed to the fact that the behavior of the material during excavation is not yet well understood. For the past five decades, researchers have mostly used the passive earth pressure theory to study the soil failure patterns around a cutting tool and to develop force prediction models for design optimization with some success. Although the force models developed from the passive pressure theory have been successful to some extent, they can hardly be extended to a general case because of the underlying assumptions and simplification of tool shapes. This paper aims at reviewing some of the existing empirical and analytical methods of cutting and excavation tool modeling with a focus on their merits and limitations. The paper also explores the use of numerical methods, specifically the discrete element method, for dealing with the unresolved aspects of soil dynamics in excavation.

Jan 1, 2011

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) am-mines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Jan 1, 2011

By S. Torno

The elimination of ultrafine (<10 µm) clay particles is essential to the treatment of abandoned coal-washing plant tailings for the recovery of the remaining coal fraction by enhanced gravity processing. Effective hydrocyclone classification is required to remove this fraction. The highly variable composition and particle size distribution of such wastes creates significant difficulties in the operation of hydrocyclones for such classifications. Hydrocyclone laboratory investigations and their plant setup require lengthy or time-consuming tests. The use of empirical models of such classifications frequently requires modification to correspond to actual operating conditions. Results of the evaluation of computational fluid dynamics (CFD) modeling to predict hydrocyclone classification of coal-washing plant tailings are presented. Results of the standard k-epsilon turbulence, SSG turbulence and large eddy simulation CFD models are compared with the results obtained from analyzed hydrocyclone classifications. The CFD models tested are shown to be very effective in the simulation of hydrocyclone classifications for the determination of the classification particle size and adequate for determining the efficiency index values for many applications. The large eddy simulation model was identified as the most precise, but it is recommended that all three models be improved simulations of classifications above and below the classification particle size.

Jan 1, 2011

By I. Gombköto, G. Földing, G. Mucsi, B. Csoke, J. Faitli, B. Kovács

This paper summarizes the main achievements of our previous project entitled "Development of a technological system producing quality guaranteed fly-ash based binder". Furthermore, this study deals with the laboratory experience of lignite fly ash utilization for two different goals. On the one hand the fly ash was tested as a binder; on the other hand it was investigated as an underground mine backfill material. Considering the first goal, the utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of relationship between the degree of activation of fly ash and the strength of the obtained concrete. The results confirmed that this hydraulic binder is suitable for construction of stabilization and capping layers or base layer. Regarding the backfilling application, this paper presents laboratory experiments, their results including settling tests, hydraulic permeability and strength measurements and dense slurry technology related results.

Jan 1, 2011

By M. Botz

Anatolia Minerals Development Limited (AMDL) is constructing the Çöpler Gold Project in eastern Turkey and commenced mining in the fourth quarter of 2009 with gold production scheduled to begin in the fourth quarter of 2010. The project is a 15,500 tonnes/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life approximately 40 million tones of ore will be placed on the leach pad, which will contain about 35,000 tonnes of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the mine life. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011