Search Documents

By D. M. Richards, A. D. MacPhail

Highland Valley Copper currently mines two low-grade ore bodies, Lornex and Valley. The partnership was formed in 1986. As a cost reduction measure, it was decided to use an in-pit crushing and conveying system to deliver the ore from the Valley Pit to the Lornex mill 3 km (1.8 miles) away and 175 m (575 ft) above the pit rim. The system uses two gyratory crushers that feed a series of conveyors to transport up to 130 kt/d (143,000 stpd) to the main stockpiles. This paper describes the performance of the in-pit crushing system as it is currently configured, as well as its evolution to date and future planned moves.

Jan 1, 1995

By A. D. MacPhail

The Highland Valley Copper partnership was formed in July 1986 and was the logical result of a mine with a large ore reserve but no adequate mill, and a mine with a large, modem mill but dwindling ore reserves. The original partners -Cominco and Lornex -were joined in January 1988 by Highmont Mining Co. which contributed a two-line concentrator. During 1988/1989, the Highmont mill was moved 7.5 km to adjoin the Lornex mill, forming what is now called the Highland mill, with a current nominal capacity of 130 000 tonnes per day. The mine is located 220 km northeast of Vancouver, British Columbia and is close to four communities in which personnel make their home: Logan Lake, Merritt, Ashcroft, and Kamloops. The map in Figure 1 2.2 shows the general area. Kamloops is a major service centre and is serviced by two railways, two major roads and a regional airport.

Jan 1, 1993

By J. Korak

Belt conveyor systems, long the standard transportation technique in soft-rock open-pit applications, are encountering growing interest in the hard-rock open-pit sector as economic factors force companies to seek an alternative to costly truck haulage. A general review of mine conveyor systems is followed by detailed analysis of the mobile and semi-mobile in-pit crushing plant essential to successful use of mine conveyors. A final section presents case studies of three crusher-conveyor systems handling overburden, copper ore and granite.

Jan 1, 1985

By James B. Fletcher

The Miami mine is located near the town of Miami, Gila County, Arizona. The Miami mine started mining in 1910 and finished in July, 1959. The orebody was divided and mined as follows: Tons High Grade 24,400,000 - Top slicing, sub-level caving, etc. Low Grade 105,100,000 - Block caving Mixed ore 9,800,000 - " Low Grade #2 13,100,000 - " Total Mining 152,400,000 GEOLOGY Ore minerals are largely in pre-Cambrian Pinal schist intruded by tertiary Schultz granite porphyry and covered to some extent by Quarternary Gila conglomerate. The structures are highly faulted and shattered. The Miami fault on the east cuts off the ore and the Pinto fault on the southwest caused re-oxidation of enriched sulphides producing mixed ore. MINERALOGY The chief mineral is chalcocite, with chalcopyrite, bornite, covellite, malachite, azurite, chrysocola, cuprite, native copper, and molybdenite as minor minerals. The ore minerals occur in seams, veinlets and disseminated particles. In block caving there is always some dilution, and drawing of ore stops when the grade drops past an economical point. This results in a small amount of copper left in the stopes below the capping. There is some copper in the capping, probably below 0.03% or less than 0.6 lbs. per ton. Over the low grade #2 orebody and portions of the high grade there was an oxide capping which was not mined. The crushed pilars are another source of copper. The leaching at Miami is an attempt to recover this last remaining copper of a worked-out mine. The enrichment at the Miami mine had gone more nearly to completion than most ore bodies in the southwest. There is practically no pyrite in the capping and very little in the ore.

Jan 1, 1971

By G. Granger, D. Malhotra

The paper briefly reviews the criteria employed in the selection of chemical reagents for testing and discusses the steps involved in laboratory and plant evaluation of these reagents. An example of successful implementation of reagent change in the plant is illustrated.

Jan 1, 1986

In order to overcome some of the deficiencies associated with conventional fine coal cleaning methods, a novel process known as microbubble column flotation (MICROCEL?) was developed at Virginia Tech. This article provides an overview of recent commercialization efforts and in-plant testing of this technology. The results of the in-plant test work indicate that the MICROCEL technology offers several advantages for the upgrading of difficult to clean coals. The test data have also been used to develop guidelines for the design of coal flotation columns and to validate existing scale-up procedures.

Jan 1, 1991

By Bernard A. Kilgore

Kaolin is a hydrated aluminum silicate mined primarily in middle Georgia along the "fall line", the location of the coast line in prehistoric times. It is used extensively as a filler for paper, insecticides, tires, plastics, a pigment for paints, as a coating for fine gloss paper, and for high grade ceramic products, such as catalytic converters. During its journey from the open pit mine to its final use, kaolin takes many forms, and must be handled in many different ways. The purpose of this presentation is to follow kaolin through its process and briefly describe some of the methods Georgia Kaolin Company, one of the world's largest kaolin producers, uses to handle and convey its product and some of the peculiarities involved.

Jan 1, 1983

By Charles C. Mosher

An in-mine seismic technique for detecting faults has been tested in a Western U.S. coal mine. This technique has been used extensively in the U. K. to help guide longwall mining operations. Explosives detonated on the face of a seam generate sound waves which propagate into the seam. Reflections from faults are picked up by sensors on the same face. Computer processing is then used to determine the fault locations. A known fault was successfully located in this test. Modifications to the U. K. procedures were required for the relatively thicker roan and pillar mines common in the Western U. S.

Jan 1, 1983

By Iain M. Mason

Linear meridional zones of bad roof conditions have been frequently encountered in producing collieries working the Permian age Lithgow seam in the western coalfield of New South Wales. The prediction of such zones ahead of mining is desirable for reasons of both safety and economics. In March, 1981, we carried out an experimental, three-component in-seam seismic survey at Invincible Colliery to discover whether such zones have any unambiguous seismic effect. The underground survey was the first of its kind to be attempted in an Australian mine. The data quality was excellent with the spectra broadband and clear. Polarisation analysis disclosed two modes: one compressional; the other shear horizontal. The SH model was clearly dispersive and well gound to the plane of the seam. Modal velocities decreased by up to 15% at the fracture-swarm site. There is a strong suggestion on the RLS maps obtained here that the distributed fault zone is acting as a composite scatterer of channel waves. The P-SV and SH wave tomograms obtained show, in a general way, the distribution of stress in the coal panel.

Jan 1, 1982

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled- waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SB) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 1, 1984

By M. M. Foss

Geophysical methods are gaining acceptance in the evaluation of coal mine ground control condition. The use of in-seam seismic investigations has contributed significantly to the body of information concerning ground control feature identification and analysis. Seismic methods have been used successfully in locating voids, faults, fracture zones, roof and floor rock interfaces, and more recently in characterizing in-seam stress distribution. Seismic tomography is an effective tool in data interpretation for several of these applications, but as is the case with other engineering application of geophysical techniques, there are limits as to how much substantive information can be interpreted from a given data set. This paper discusses some of the applications of in-seam seismic geophysical tomography, and the limits to which the transformation from raw data to information should be taken.

Jan 1, 1995

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

By R. Schlüter

"The global mining industry is facing increasing challenges in terms of geological, technological and social aspects. Potential exploi-tation of deposits shows a tendency to increasing depth with complex ores and decreasing grades. A promising approach to deal with these constrains is by applying alternative extraction methods like (bio-)hydrometallurgy as in-situ leaching (ISL) technology. The Bergakademie Freiberg University of Mining and Technology established the “Biohydrometallurgical Center for strategic Elements” (BHMZ) to foster the interdisciplinary research along the entire biohy-drometallurgical process chain to extract indium from sulfide ores. The involved Department of Underground Mining Methods deals with the design and implementation of a pilot-scale underground testing facility for microbial in-situ stope leaching in its “Research and Educational Mine”. This paper discusses the potential of in-situ bioleaching under technological aspects. In addition, different conditioning approaches based on hydraulic and explosive methods for enhanced permeability in the formation are introduced and the gathered data will be presened. INTRODUCTION A reliable, substantial and sustainable supply of raw materials is of crucial importance for any industrialized country. This dependency applies to “strategic elements” including rare earth elements (REEs), platinum group metals (PGMs) as well as a variety of other metals like indium and germanium which are needed for high-tech industry and products such as electric and electronic devices, fibre optics and laser technology (Barakos et al., 2016; European Commission, 2010). Due to the economic growth of the BRIC-countries (Brazil, Russia, India, China), the resource policy of China as well as the volatile world mar-ket prices of different metals the availability of these critical raw materi-als and therefore the dependency of the high-tech producing countries has become increasingly important (Barakos et al, 2016). Adequate supply is often affected by the increasing depth of de-posits, lower metal concentrations and more complex ore mineralogy. In addition, mining activities are increasingly restricted by their envi-ronmental and social impact and footprints. As a consequence, con-ventional mining and processing methods are limited by high energy consumption and technical constraints."

Jan 1, 2018

By A. M. Johnson

Although known primarily for native copper, the Keweenaw Peninsula of northern Michigan also has deposits of copper sulfide (chalcocite) ore. A number of small, but rich, deposits are present at relatively shallow depths near the base of a thick, steeply dipping sequence of volcanic and sedimentary rocks. Because much of the ore is fracture-controlled, the deposits appear to be ideal candidates for in-situ leaching. Fracture mapping from drill core and borehole logs coupled with borehole packer permeability tests are being applied to evaluate the suitability of the ore for in-situ leaching. A leaching scheme utilizing a bacterial-assisted ferric iron lixiviant is being tested at bench scale. A pilot scale test is being designed to evaluate the system in the field.

Jan 1, 1988

By P. Somasundaran, A. Sivakumar

Surfactants and polymers are used in a number of processes such as flotation and flocculation. The structure of the adsorbed surfactant and polymer layers control the interfacial properties of the solid and hence an understanding of the structure of the adsorbed layers at the molecular level is essential. In this paper, a review of different spectroscopic techniques (fluorescence, electron spin resonance and Raman) used to characterize the adsorbed layers [in-situ] is presented. Information on the micropolarity, microfluidity and size of the surfactant aggregates was obtained and the growth of the adsorbed layer was followed. [In-situ] conformational states of polymers at the solid/liquid interface were determined for different pH values.

Jan 1, 1989

By W. Lin, E. Heuze

This paper focuses on tests performed on sandstones and shales from four gas wells in the Mesaverde formation. A previous document showed a comparison of the static and dynamic laboratory moduli. This publication describes how field velocity logs were used to derive field dynamic moduli. A 3-way comparison was then performed for these stiffness properties; the results show no agreement between the three sets of values. Differences between dynamic stiffness coefficients from the field and the laboratory exceed 200%; differences between static and dynamic coefficients range up to 600%. In turn, this indicates that a reliable method of estimating mechanical rock properties for hydraulic fracturing design has not been established, and that such a task should be pursued.

Jan 1, 1986

By Sidney A. Suhler

The persistent requirement for methods and equipment capable of detecting hazardous anomalies in advance of underground mining has led to the development by the U.S. Bureau of Mines of a directional radar probe. The probe operates from boreholes drilled from the surface into the underground region to be mined. The engineering model radar was completed in early 1982 and field demonstration tests were performed in May of that year at a selected coal mine. Preliminary in-situ electromagnetic tests were performed at several candidate coal mines to evaluate the radio-frequency characteristics of the coal. A coal mine in New Mexico was selected on the basis of low EM propagation losses in the coal and the presence of an extensive coal seam displacing fault as a radar target. The borehole radar was operated in two vertical boreholes which intersected the coal seam at approximately 25 and 40 feet from the fault interface. Radar reflections from the coal/ rock interface were detected in both tests. Underground tests in a horizontal borehole in the coal were less successful because of interfering reflections. Additional borehole-to-borehole tests were performed with a separate ground penetrating electromagnetic system to obtain radar range calibration data. The coal was found to be bounded by very lossy roof and floor sandstone and shale while propagation through the coal seam was obtained at distances up to 175 feet between test boreholes. Coal seam continuity was indicated by the hole-to-hole experiments through a section of the seam previously thought to be completely cut off by the fault.

Jan 1, 1983

By Jon J. Kellar

The adsorption of oleate at the surface of a fluorite single-crystal internal reflection element has been investigated using Fourier transform infra-red/internal reflection spectroscopy (FTIR/IRS). The application of this innovative experimental technique has added a new dimension to the investigation and understanding of collector adsorption phenomena. It is now possible, for the first time, to measure in-situ and in real time the adsorption density and bonding nature of collector species adsorbed at mineral surfaces. In this regard, oleate adsorption densities were calculated from spectral data, and the equilibrium adsorption isotherms were found to agree quite well with other adsorption isotherms reported in the literature. At low equilibrium oleate concentrations(<10-5 M), monolayer-type cover-age was observed in the chemisorbed region. It was found that in this region the adsorption density increases with an increase in temperature, which sup-ports experimental results from previous ex-situ FTIR studies and thermochemical studies in which it was shown that the chemisorption reaction was endothermic. At higher equilibrium oleate concentrations (>10-5 M), the adsorption density increases dramatically at the point of surface precipitation. The oleate adsorbed in the chemisorbed region has a distinctly different spectrum than the oleate adsorbed in the surface precipitation region of the adsorption isotherm. In the chemisorbed region, the oleate appears to be mono-coordinated at the fluorite surface.

Jan 1, 1989

The properties of interfacial water at hydrophilic surfaces are of great importance in many technological areas including flotation, solid-liquid separation, dispersion and emulsions, flocculation, adsorption, corrosion, and soil contamination. This paper examines the use of FTIR/internal reflection spectroscopy (FTIR/IRS) to study the spectral characteristics of interfacial water at silica surfaces. FTIR spectra were characterized by consideration of the OH stretching region (3000-3800 cm-1) associated with the vibrational spectra of interfacial water. The broad peak in this region was deconvoluted in order to isolate overlapping spectral features that describe the nature of hydrogen bonding in interfacial water. Three distinct bands were found; -3600 cm-1 (free OH), -3400 cm-1 (incomplete tetrahedral coordination), and -3240 cm-1 (complete tetrahedral coordination) and the variation of their intensities with pH was found to be significant. This spectral information helps to explain orientation and bond ordering of interfacial water molecules at hydrophilic surfaces.

Jan 1, 1998

By Brian H. Jasperse, Nicholson Peter J.

Gravity retaining walls have been constructed using Deep and Shallow Soil Mixing (DSM and SSM) since 1991 in the United States. These walls, for both temporary and permanent uses, were constructed by mixing cement with in-situ soils over a volume containing 100% of the required gravity wall zone. Modern design techniques have reduced costs substantially by forming the required gravity wall section as a composite mass. Using ratios of 15-35% by volume, treatment f the ground forming the required gravity section has reduced the cost from about $40 to about $20 per square foot. Design, construction and actual performance of these gravity walls are presented.

Jan 1, 1999