Search Documents

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015

By PATRICK R. TAYLOR, NICHOLAS BELLUSCI, D. ERIK SPILLER, VICTOR BRAMAN

Most of the world’s production of natural soda ash comes from the mining and processing of trona found near Green River, WY. The processing of trona ores to ultimately yield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale, is water and energy intensive. It is speculated, however, that the glass-manufacturing industry, which is the largest consumer of soda ash, may be able to use product of a lower grade and consistent level of the insoluble constituents. Thus, the viability of using sensor-based sorting to produce a beneficiated trona stream that would be fed to calcination was investigated. The study encompassed the preparation of a run-of-mine (ROM) Green River ore sample; selection of specimens sized 25 to 75 mm; imaging of the specimens by sensors based on X-ray transmission (XRT), color and laser-induced fluorescence (LIF); insolubles analysis of the specimens; and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content exists, and that a surface-detection-based sensor, particularly LIF, is apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65 percent separation efficiency and a 70 percent recovery of trona could be achieved.

Feb 1, 2023

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By David T. Kao

The energy situation the world faced during the decade of the Seventies resulted in actions throughout the free world to reduce its dependence on OPEC oil. Many nations heeded the indicators early in that decade and commenced efforts to reduce their oil requirements. Those nations which did not heed these warnings had the message brought to them more emphatically in the last portion of the decade with the further rapid and continuing rise in prices of OPEC oil. Furthermore, the demonstrated unstable nature of large oil-producing countries has made it clear to all free world nations that their energy demands of the future must be provided for by some more stable and assured supply. Now, early in the decade of the Eighties, we see the need for expanded use of coal as an energy supply to be essential. The result in 1980 and 1981 has been a great increase in demand for steam coal worldwide. In essence, a new business for the United States has developed in steam coal export. In the United States, the large growth in foreign demand for our steam coal is now well recognized and documented. A major impediment in meeting this growing demand became abundantly clear in 1980. This impediment is the congestion existing at U.S. coal export ports. With the recognition of this constraint, a plethora of activity has been observed in announcements for alleviating the problem by improving and expanding current export port facilities. In addition to improvement and expansion, an abundance of totally new facilities has been announced in an effort to find ways to meet this large demand in the new business of steam coal export. This is needed; and hopefully, many of these plans will be translated into action. While total implementation of all stated plans is not expected, much of the implementation depends upon large- scale dredging, large waterside ground storage sites, and improved handling equipments in the conventional type of export ports. The time and capital required for implementation is great, and environmental problems associated with dredging are substantial. Host significantly, and unfortunately, implementation that does include dredging our ports will still not permit use of the truly large colliers of 140,000 DWT and greater, which are evolving as the "state of the art" in long-distance sea transport.

Jan 1, 1981

By M. A. Sochocky

Rod mills were developed, as a logical substitute for the rolls crusher when larger tonnages had to be handled, on a continuous basis. Today, with even larger tonnages to process, the trend is to install larger equipment, automate the plant and develop the highest availability possible, in order to cut costs. The rod mills, because of design limitations in size and speed 1'2, are not able to meet these new requirements. The autogenous mill was a timely development and serves as an excellent alternative for ores that are suitable to this type of grinding. When ores are not amenable to autogenous grinding, selection of a flowsheet is dictated by liberation characteristics and unit operations to be used for mineral recovery.. The following alternatives are available: (a) Multiple rod mills, capable of drawing no more than 2000 HP each, followed by ball mills. (b) Gyradisc crusher followed by two stages of ball mill grinding.3 (c) Tertiary crushing followed by closed circuit single stage ball mills grinding to approximately -100 mesh, as in the copper industry. (d) Tertiary' crushing followed by two-stage, ball milling. Each stage will operate in closed circuit with either screens or cyclones. It is this last alternative, particularly as it

Jan 1, 1972

A new separator, known as the HydroFloat cell, was developed to overcome the limitations of traditional flotation cells in recovering coarse particles. The HydroFloat cell separates particles based on differences in mass after the selective attachment of air bubbles to the hydrophobic component of the feed stream. Proof-of-concept testing, utilizing phosphate matrix, heavy mineral sands and anthracite slag, indicated that significant improvements in separation efficiency can be achieved using this air-assisted teeter-bed system. Based on the encouraging laboratory results, a pilot-scale HydroFloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the +35-mesh plant feed can be increased by snore than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the +16-mesh particles in the HydroFloat concentrate. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 2002

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Jan 1, 2011

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Nov 1, 2011

By G. Brooks, J. T. Ellington, M. Yensco, G. E. Mcquien, M. T. Ityokumbul

Coarse silica flotation from intermediate pebble (IP) product has been carried out a pilot plant Dual Extraction Column (DEC) at an operational phosphate mine in Central Florida. The solids feed rate ranged from 4.16 – 5.3 TPH while the amine dosages ranged from 0.32 – 0.93 lb/T. The optimum amine dosage when using recycled process water was deter-mined to be 0.6 lb/T. With a feed containing 40-45 BPL and 38-45% insol, the results show that the IP can be upgraded to 56-61 BPL and insol of 16-22% at 85-90% BPL recovery. The results show that the DEC is an effective device for flotation of coarse silica from the IP. The advantages of upgrading the IP prior blending with the pebble are presented and discussed.

Jan 1, 2004

By Bradley S. Van Gosen, Anjana K. Shah, George M. Bedinger, Donald I. Bleiwas, Karl J. Ellefsen

"Ancient and modern coastal deposits of heavy mineral sands (HMS) are the principal source of several heavy industrial minerals, with mining and processing operations on every continent except Antarctica. For example, HMS deposits are the main source of titanium feedstock for the titanium dioxide (TiO2) pigments industry, obtained from the minerals ilmenite (Fe2+TiO3), rutile (TiO2) and leucoxene (an alteration product of ilmenite). HMS deposits are also the principal source of zircon (ZrSiO4), from which zirconium dioxide (ZrO2) is obtained for uses mostly in refractory products. Sometimes monazite [(Ce,La,Nd,Th) PO4] is recovered as a byproduct mineral, sought for its rare earth elements, and thorium (Ault and others, 2016; Sengupta and Van Gosen, 2016; Van Gosen and Tulsidas, 2016).HMS are sediments containing dense (heavy) minerals that accumulate with sand, silt and clay in coastal environments, locally forming economic concentrations of the heavy minerals (Fig. 1). Economic (mined) HMS deposits include Holocene sediments on modern coasts, such as examples in India and Brazil, as well as coastal deposits formed by transgressions and regressions of the seas during intervals in the Quaternary, Tertiary and Cretaceous, such as in Australia and the southeastern United States. Economic deposits typically contain heavy-mineral concentrations of at least two percent. Individual heavy minerals are commonly defined as minerals with a specific gravity greater than approximately 2.9 g/cm3. These minerals are generally resistant to chemical weathering and physical degradation and thus survive well in fluvial and coastal environments. Heavy minerals in coastal HMS deposits may include, in order of general abundance, ilmenite, leucoxene, rutile, magnetite, zircon, staurolite, kyanite, sillimanite, tourmaline, garnet, epidote, hornblende, spinel, iron oxides, sulfides, anatase, monazite, cassiterite and xenotime. Of these, ilmenite, leucoxene, rutile and zircon are the primary economic minerals. Garnet, monazite, cassiterite and xenotime are occasionally recovered as byproducts. The heavy minerals as a suite typically make up no more than 15 weight percent of a deposit and usually much less. Quartz and clay minerals form the bulk of the sediment. The geology of HMS deposits and examples of significant districts are summarized in Van Gosen and others (2014) and Hou and Keeling (2016)."

Oct 1, 2016

By Mark D. Cocker

Georgia?s Coastal Plain contains important sediment-hosted deposits of kaolin, bauxite, heavy minerals, sand and gravel, silica sand, carbonate rocks, and fuller's earth. Genesis, location, size, and quality of these deposits are related to terrestrial, marginal-marine, and shallow-marine depositional environments that evolved during development of the southeastern North American continental margin. From the Cretaceous to Eocene, kaolin and aluminous sediments, which contained mica and feldspar, were deposited in marshes, ponds, and bays located in deltas or behind barrier islands or spits. In the Cretaceous sediments, subsequent, intensive, in situ chemical weathering converted mica and feldspar to kaolin. Kaolin eroded from deeply weathered granitic rocks in the Georgia Piedmont was deposited in Paleocene to Eocene sediments. Subaerial exposure during the Paleocene and Eocene desilicated kaolin sediments to form bauxite. Sand and gravel, silica sand, and heavy-mineral deposits are found in Cretaceous to Eocene fluvial and shoreline sediments, some of which are associated with the kaolin and bauxite deposits. Source areas, intensive chemical weathering in the source areas, transportation by the major river systems, and deposition of these clastic sediments in similar or nearby depositional environments are common elements in the genesis of these resources. Eocene fuller's-earth deposits are opaline claystones in near-shore to shelf-marine sediments, which overlie the kaolin-bearing strata. These claystones consist of montmorillonite and opal/ cristobalite derived from alteration of diatom frustules. Favorable ocean currents provided nutrients for extensive planktonic growth. Oligocene and Miocene carbonate rocks were deposited principally in shallow-marine embayments. Miocene fuller's- earth deposits in south-central Georgia and adjacent parts of Florida contain palygorskite that formed through alteration of montmorillonite/bentonite clays. Deposition and subsequent alteration occurred in shallow, brackish-water lagoons under relatively high temperature and subtropical conditions. Middle and late Miocene phosphorites were deposited on a shallow carbonate-shelf platform and were concentrated proximal to anticlinal highs. Numerous marine transgressions and regressions since the beginning of the Pleistocene resulted in shoreline detrital deposits containing aggregate sand, silica sand, and heavy minerals on the Coastal Plain and on the Continental Shelf. Major river systems transported sand and heavy minerals from source areas in the Piedmont and Upper Coastal Plain. Deltaic deposits of heavy minerals were redistributed and concentrated by longshore currents, shoreline processes, and aeolian processes. River-terrace sediments, correlative with the Pleistocene shoreline deposits, contain sand-and-gravel and silica-sand deposits. Aeolian dune sands are associated with both Pleistocene fluvial and shoreline detrital deposits.

Jan 1, 1999

By T. J. Driscoll

The effect of coatings on the incendive properties of aluminum alloy 6061-T651 in air-6.4%CH4 was studied for collisions between rusted steel and both uncoated and coated projectiles with incident energies as high as 300 J (220 ft-lb) and velocities as high as 200 m/s (660 fps). These conditions were intended to simulate the rough handling of equipment in coal mines. The ignition probability using uncoated alloy projectiles increased with increasing relative humidity and appeared to be influenced by atmospheric ozone content. The incendive properties of both the uncoated and coated alloy depended on the type of rust used, but the dependence of the coated alloy was very different from that of the uncoated alloy. A number of coatings developed in the last 25 years were found to offer protection from ignition and to remain largely intact for occasional collisions or collisions randomly distributed over the coating surface, but probably not for repetitive collisions at any given point on the coating. These protective coatings utilize a hard anodized aluminum alloy surface coated with one or more layers followed by heat treatment of the coating. Coatings containing Teflon and MoS2 and thicker than 50 µm (2 mils) appear to be most effective.

Jan 1, 1987

By Mark A. Koestel

Cobalt-sulfide mineralization can he found in potentially economic quantities where permeable, basal Cambrian formations "pinchout" against Precambrian pal eotopographi c highs. These environments are common around the Saint Francois Mountains of southeastern Missouri and they share many similarities with the geologic environments of Zambia and Zaire in South Africa. Exploration for this type of deposit involves test drilling targets identified by trend analysis from past drilling, geophysics, geochemistry and a comprehensisve study of regional geology and isopach maps. Innovative ideas, new exploration concepts and insoluble residue geochemical methods may provide the necessary "edge" needed to complement basic geologic understanding leading to ore discovery.

Jan 1, 1987

By M. Rodgers

Dow Water & Process Solutions (DW&PS) was approached by ASARCO Inc. to attempt to recover cobalt and copper from their copper solvent extraction (SX) raffinate. Cobalt is added to many copper electrowinning tankhouses to help to prevent lead electrode corrosion. With cobalt?s high price this can be a large expense. ASARCO has ore that contains a small amount of naturally occurring cobalt. Currently they have no way of capturing this high value metal from their leach or raffinate streams. DW&PS has some chelating resin technologies that should be able to help solve this problem.

Jan 1, 2010

By Peter Amelunxen, Kain Nugent, Brandon Akerstrom, Willem Duyvesteyn, Todd Harvey

In 2024, Capstone Copper Corp commissioned a new sulfide flotation plant at Mantoverde in the Atacama region of Chile to process copper ore at a design rate of 32,000tpd. The pyrite associated with the copper ore body contains cobalt in solid solution, with Co replacing Fe in the pyrite matrix. As per the existing sulfide flotation flowsheet most of the pyrite is depressed and sent to tailings via the cleaner scavenger tail stream. A new project considers the recovery of the pyrite from the cleaner-scavenger tails via froth flotation to produce a cobaltiferous pyrite concentrate, which is then leached via the existing dynamic copper leach pad to oxidize the pyrite and dissolve the cobalt. The cobalt is recovered from the solution by treating a bleed stream of copper SX raffinate through a continuous, counter-current ion exchange (CCIX) facility. This approach to by-production of cobalt confers numerous benefits, including reduced costs compared with alternative cobalt recovery processes, reduced acid consumption in the heap leach, increased copper production, and reduced acid mine drainage potential due to the removal of pyrite from the mill tailings.

Feb 1, 2025

By P. Ashayer, J. Curran

Introduction Rockfalls occur when rocks or boulders detach from mountains or hills and tumble down. They can pose significant hazards to infrastructure such as highways, buildings, and mine open pits, and they sometimes result in personal injury or death. Prediction of rockfalls is a difficult task. Slopes that are at risk of rockfall have highly variable geometries. The location, mass, and shape of the rocks that might dislodge and fall are uncertain. Moreover, the materials that make up a slope can vary considerably from one section to another. Furthermore, the relevant material properties are usually not well known. Performing probabilistic simulations of rockfalls, combined with proper statistical analyses, has proven to be an effective and acceptable method for dealing with these difficulties [1, 2, 3]. The movements of a falling rock can be classified as freefall, bouncing, sliding, toppling, or rolling. The falling trajectory is controlled mainly by the geometry of the slope, the block shape, and the energy dissipated at each contact of the block with the slope. A rockfall model is evaluated based on its ability to efficiently predict the velocity, frequency, height of bounce, and run-out distance of falling rocks. With this information, the engineer can design remedial measures such as restraining nets and ditches. Most of the existing rockfall simulators are based on particle models that consider the falling rock as an infinitesimal particle with a mass, called the lumped mass or stereomechanical models [1, 2, 3, 4]. Other models involve hybrid methods relying on simplified assumptions. The most common hybrid methods are based on contact searching for the movement of a dimensionless object and incorporate some aspects of rigid body impact for bouncing [5, 6, 7]. There are also some rigid body models in the literature that employ simplified versions of rigid body models [8, 9]. This study applies a more sophisticated rigid body theory based on rigid body impact mechanics (RBIM), which was developed by Stronge [10, 11, 12]. The new theory captures all modes of rigid body movement. Due to the importance of the rock geometry, single impacts of ellipsoidal and prismatic rocks with rectangular cross sections are investigated. The effect of rock slenderness on rebound velocities and energies is also investigated for ellipsoidal rocks. The correspondence between the model parameters and the data from the rockfall literature data will be discussed.

Jan 1, 2007

By Diana Diaz, Rakshith Shetty, Vitaly Proschenko, Mike Mooney

Cohesive clay soil poses a significant risk to earth pressure balance tunnel boring machines (EPBM) due to unstable face pressure, clogging potential, high cutterhead torque, poor muck flow, low advance rate, etc. This paper details the performance measures desired when EPBM tunneling in clay soil, and the scientifically-supported conditioning methods to transform in-situ clay to a muck with such characteristics, giving particular attention to ground conditions. The paper then examines TBM data from multiple clay soil projects in the context of these performance measures to demonstrate the influence of cohesive soil conditioning on EPBM performance.

Jun 13, 2023

By John D. Price

In the constant search for ways and means of improving the quality of coke and thus making its use at the blast-fornace more satisfactory and economical, it has become increasingly evident that the present laboratory tests do not show the full picture of a coke's value as a blast-furnace fuel. This fact was recognized by Dr. A. C. Pieldner thirty-five years ago: (Ref. 1) here is perhaps no phase of fuel technicology which has aroused more discussion or regarding which there is more difference of opinion than the properties of coke which make it most suitable for blast-furnaces and other uses." Dr. Fieldner followed this assertion with a statement to the effect that men who write on this subject today (1923) have, because of conflicting experimental evidence brought forth in recent years, far less positive opinions on the matter than did writers of some years past. One is led to wonder if these statements are not just as true now as they were when first made.

Jan 1, 1959

By Richard J. Wilson

The importance of coal as a major source of energy used by the steel industry has been increasing due to the gradual changeover from steel- making by the open hearth process to steelmaking by the basic oxygen process. Since the production of steel by the BOF process increases the demand for hot metal, there is a growing need to ensure the supply of coke required for the production of hot metal. Coal used for cokemaking has become, therefore, an increasingly important raw material for the steel industry in recent years. Our current projections indicate that coal will be the source of 71% of the total energy requirements of Inland Steel Company in 1985. As a result of the energy shortages of the last few years, various conservation programs have been initiated by the steel industry to reduce the consumption rate of fuel. The efforts to conserve energy have been successful to a great extent due to the rapid advances made in the technology of ironmaking that facilitated gradual reductions in the quantity of coke used per ton of hot metal produced in the blast furnaces. The decrease in the consumption rate of coke was made possible by the use of improved raw materials, such as iron ore pellets and fluxed agglomerates, the operation with high blast temperatures, the injection of auxiliary fuels, and the enrichment of the blast with oxygen. It is expected that additional reductions in the fuel consumption rate will be possible in the ironmaking operations of the large blast furnaces that are being equipped with facilities for proper burden distribution and for operation with higher blast temperatures at high top pressure. The purpose of this paper is to show the effects of coke quality on the production of BOF steel. The importance of coke quality will be pointed out by discussing the effects of the physical strength of coke on both the blast furnace productivity and the steelmaking operations of an integrated steel plant, such as Inland Stee1 Company.

Jan 1, 1980

By Paul Hosford, B. Thrall

There has been a surge of exploration activity and interest in mineral properties located in cold Northern climates, with gold and copper properties as the two most attractive targets. There are already a number of mining operations located in the Arctic, for example, Red Dog, Polaris, and Lupin, all located in the Canadian Arctic. The logistics of sustaining operations, the engineering design and construction methods for such inhospitable regions are now relatively well understood. However, at least three of the proposed new mines in the Yukon Territory, Canada are designed to be heap leach operations. Rescan Engineering has recently completed Feasibility studies for two heap leach operations in the Yukon, one of which, the Brewery Creek Mine, is now in operation. The purpose of this paper is to explore some of the engineering and operating concepts that have been developed to make heap leaching an appropriate process method for gold recovery in a cold climate. Many of the readers will be familiar with the general and specific details of heap leaching, and it is not the intention of the authors to deal with any of the established "do's" and "don'ts" that have been addressed in numerous previous papers, but only with those pertaining to cold weather operations. This paper also examines these design concepts in specific relation to the results of the first winter's operation at Brewery Creek Mine, the first "far" North heap leach operation.

Jan 1, 1997