Search Documents

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

By Robert L. (Original by) Llewellyn

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment.

Jan 1, 1981

By Vas Choudhry

The eighties are likely to witness the first commercial-size coal-to-gasoline plant(s) in the U.S., although uncertainty regarding crude prices and cautious involvement of the Federal Government in the synfuels development are evident. The formation of The U.S. Synthetic Fuels Corporation with passage of the Energy Security Act is projected to pave the way for some of the projects on a moderate scale. The corporate objectives (1) are to provide funds for supporting a number of feasibility studies and loan guarantees for the construction of at least some commercial-size plants and the possibility of product price supports or purchase commitments. There are a number of coal conversion processes (2) currently under evaluation for producing either gaseous or liquid plus gaseous fuels, the other processes such as SRC I are for producing desulfurized deashed clean solid fuel for commercial use.

Jan 1, 1982

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By J. N. Cox

Coal preparation is based on the properties of noncombustable materials (impurities) in coal being different from the organic constituents. The most commonly used property difference is density, via its affect on settling rates; and either gravitational or centrifugal forces can be used to remove impurities. However, examination of various particles settling rate correlations shows that at smaller sizes, particle drag becomes a very important factor. Classification, based on differential settling rates, becomes impractical and some property other than density must provide the basis for fine coal cleaning. Froth flotation and agglomeration employ differences in surface properties to clean coal. These methods are very successful except that the oxidized surface of a pyrite particle is somewhat hydrophobic and will tend to be collected with the organic portion of the coal. Surface property cleaning techniques have not been very effective in rejecting sulfur, except for two-stage flotation.

Jan 1, 1984

By Eugene R. Palowitch

From the late 1880s to the present, the Appalachian region continues to be a dominant supplier of premium-quality coals. The region contains an estimated 93.4 Gt (102.7 billion st) of demonstrated reserves in Alabama, eastern Kentucky, Maryland, Ohio, Pennsylvania, Tennessee, Virginia and West Virginia. Therefore, Appalachia will remain a source of quality coals for the metallurgical, export and utility markets. Figure 1 shows the annual production of coal in Appalachia and nationally from 1970 through 1993 (Energy Information Administration, 1994). During that 23-year period, annual domestic coal production almost doubled. Coal production from Appalachia increased at an average annual rate of only 0.7%. Coal production remained essentially constant at about 409 Mt/a (450 million stpy). Thus, Appalachia's market share decreased from 69.8% in 1970 to 47.2% in 1993 - a drop of almost one-third (Energy Information Administration, 1994).

Jan 1, 1995

By Elmer H. Citron

The Monterey Coal Company, a wholly owned subsidiary of The Carter Oil Company of Houston, Texas, recently awarded a contract to build the Monterey No. 1 Preparation Plant, which will be located near Carlinville, Illinois, to the McNally Pittsburg Manufacturing Corporation. The preparation plant will be one of the most modern jig preparation plants in the State of Illinois. Illinois No. 6 coal will be delivered by a 48" slope belt having 35-degree carrying idlers, operating at 650 FPM and operating on an incline of nearly 17 degrees. The slope belt is driven by two 450 BP motors and will deliver the mined coal at the rate of 1800 TPH to a stationary step-type ' screen having six-inch openings. The overproduct from the stationary screen will discharge into a 10' x 24' McNally Rotary Breaker and the underproduct will bypass the rotary breaker. The rotary breaker is equipped with heavy manganese screens with 6 ½" diameter openings. The sized 6" x 0 coal from the stationary step screen and the rotary breaker will be discharged by gravity to a 4%" raw coal incline storage belt. The 48" raw coal storage belt will deliver the 6" x 0 sized coal at the rate of 1800 T?H to an 8000 ton concrete raw coal silo, 70 feet in diameter and 1x7 feet high. The 6" x 0 sized coal will be drawn from the concrete storage silo by seven (7) 36" wide reciprocating plate feeders. Five feeders are to have constant speed drives at a rated capacity of 145 TPH each. Two (2) feeders will have remote con- trolled variable speed drives, to provide a varying feed.

Jan 1, 1970

By M. Kaya

The main purpose of this study was to design a modular/mobile coal preparation plant with a capacity of 300 t/h for Seyitömer B3 vein (almost 70% of the whole SLI deposit). Firstly, coal washing properties and washability curves were determined by sink and float tests. Then, equipment sizing, selection, flow sheet development, economic evaluation, investment and operating costs were determined for coarse (-150+18mm), fine (-18+0.5mm) and slime (-0.5+0.1mm) coals. Economic evaluation of the proposed flow sheet showed the feasibility and profitability of the investment.

Jan 1, 2006

By J. W. MacDonald

PROPERTY AND PRODUCTION: Around 100 Million Tons of Recoverable Coal are available from the approximate 10,000 acres allocated to the mine. Over 1300 acres of surface land holdings extend well beyond the limits required for plant site, storage tracks, water supply reservoir, settling ponds and waste disposal. COAL: Extensive core drilled testing confirmed the early indicated high quality of the #6 Seam Washability data show less than four percent of the' coal seam required removal to provide a superior product for the available market. PREPARATION PANT DESIGN: The limited needs enabled Preparation Plant Design to meet the requirements without inclusion of novel equipment. The simplified needs afforded ample opportunity for considering increased automation where advantage or economy was antioipated. Plant design included protection of opportunity for pre-drying in advance of air cleaning the fine coal and accommodations for addition of Dense Media separating equipment in event warranted or required by future market changes. Protection is also afforded for addition of Raw Coal Storage accommodations in event warranted. Figure I shows the Preparation Plant Flow Sheet.

Jan 1, 1961

By John Hillman

The reconstruction of the British mining industry which began shortly after nationalisation in 1947 continued until well into the 1950s with the support of the Government. This support diminished as plentiful supplies of cheap oil from the middle East made many coalmines un¬economic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined the financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A Government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal' (1). Plan for Coal aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The Plan proposed action along the following lines (a) increase output by major Investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output (b) invest in extending the life of existing collieries by gaining access to additional reserves, to give 12 million tons per annum extra output © by sinking new mines, produce an extra 20 million tons per annum. Figure 1 shows the contribution (2) expected from each of the three sources up to 1990/1. The measures taken were expected to offset the inevitable exhaustion of existing pits and provide the additional 40-42 million tons capacity needed to restore annual output in 1985 to 120 million tons. Parallel to this programme for expansion of deep mined output, opencast mining was to produce 10-15 million tons per annum. A recent review however, indicates that new mines are likely to yield only 10 million tons per annum by 1985, mainly owing to the need for public inquiries into proposals for new mining and the resultant fact that planning approval takes 'much longer than originally expected. Nevertheless the objective of 120 million tons deep mined output by 1985 is still considered achievable of means of a greater contribution from existing mines. This programme was originally estimated to cost 2,-56 million dollars at March 1974 prices, out revised estimates of the cost of Plan for Coal indicate that it may now exceed 6,960 million dollars at mid-1977 prices. Plan for Coal includes a substantial investment in new and reconstructed coal preparation plaints. At mid-1977 prices more than 322 million dollars Ls so be invested in coal preparation projects in the UK, at the rate of, about 70 million dollars a year. This rate 3f capital expenditure has been maintained over the past three years and covers investment in a wide range of coal preparation coals for the power station, coking and domestic markets.

Jan 1, 1978

By Atmesh K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high Btu low sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high Btu midwestern coal and blending it with low sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal is presented.

Jan 1, 1984

By V. Russel Burkhart

One of the most difficult items to justify economically on any budget is a training program. The costs can easily be identified--primarily the cost of the program and the inconvenience and cost of filling in for the men taking the training by working other personnel extra hours at overtime rates. Operating efficiency, higher productivity, increased plant availability, development of confidence, improvement in morale and less absenteeism are only a few of the benefits which far exceed the costs. A good preparation plant training program can accomplish more in 5 weeks than can be accomplished in five years of on-the-lob operation. During recent years, coal preparation plants have become more sophisticated and complex as the specification for coal used by electric utilities in their power plants have required improvements in coal quality to adhere to air quality regulations and to improve boiler performance and reliability.

Jan 1, 1981

By Keith Kern, Joseph P. Matoney, Kenneth E. Harrison

INTRODUCTION "When there is an economic need for cleaning fine coal to low ash, the technical difficulties will be solved. The utilization of fines below 28 mesh will determine the degree to which beneficiation will be carried. Whenever these "fines" will be processed into smokeless fuels or used as new materials for the chemical industry or for hydrogenation, a higher degree of cleaning will be economically justified”.(l) This quote from the 1943 edition of Coal Preparation correctly anticipates the use of fines as "smokeless" fuel or as a future component of boiler fuel and a1 so as a raw material for the chemical industry or possible new uses such as for internal combustion engines. Fines utilization depends upon an economic need and possibly neglects to say an environmental need or a government funded development program as the prime mover for development. In any event, this conference is faced with the "need" to beneficiate fine coal and undoubtedly among the processes that will be discussed are the unit processes of future coal preparation facilities. HISTORY OF DEVELOPMENT It is interesting to look at where we have been, where we are now and where we possibly will be in the future. In order to put some limitations on this presentation, we will for the most part confine our remarks to this century and particularly developments since World War II. We also will limit our remarks to the preparation of bituminous coals in the United States, and for the most part, to wet processes. In the 1943 edition of Coal Preparation, clues to the processes being used to beneficiate coal are contained in the Chapter Titles. An extensive treatment of "Hand Picking" was contained in Chapter 8. Chapter 7 contained a description of methods for "Preparation at the Face". Chapter 18 dealt with "Slurries, Sludges, Slimes and Water Treatment" and defined this size of coal as being the size at which "Jigs and Chance Cones are usually dispensed with and other methods such as the hydrator, tables, and froth flotation are employed. Generally the limit is 1.7mm to 3.4mm. In the days before World War I1 the then modern bituminous coal preparation plant contained jigs or Chance Cones for the coarse material +6.35mm, concentrating tables, launders or some classifier type of coal washer for the fines (6.35 x 0.15mm), and froth flotation as the only method of cleaning minus 0.15mm coal which was used very sparingly.

Jan 1, 1988

By William Gleason

"Once the primary fuel source for the United States and the economic backbone for communities from Appalachia to Wyoming, coal has been on a steady decline since the mid 1990s, and is now at the center of political debate in the United States.The political spectrum of the United States is divided on the future of coal and its place in the energy sector. The coal mining industry and the communities that rely on coal have increasingly been pitted against forces that wish to regulate coal to the history books.In 2008, President Obama launched what many have called his war on coal, and during his eight years in office, he pushed through numerous pieces of regulations and legislation and that he said were aimed at reducing carbon emissions, but that others viewed as direct assaults on the domestic coal industry. Obama led the United States delegation to Paris to sign the Paris Accord in 2016, a 196-country agreement pledging that the United States would do its part to reduce carbon emissions. His administration also instituted clean air, power and water regulations that added extra environmental burdens to many industries, but perhaps none more so than the coal industry.In this month’s lead feature, “A study of U.S. coal mine closures since 1994” (page 18), the impact of the war on coal, and other factors, can be seen in text and figures. Author Jacob Brinkman and coauthors Jay Schafler and Catherine Johnson scoured the data of the U.S. Energy Information Administration (EIA) and the U.S. Mine Safety and Health Administration (MSHA) to show how coal production and mines have been impacted since 1994 and how the years 1994 to 2000 and 2008 to 2016 were particularly hard on the industry.For example, in 1994 there were 2,354 coal mines in the United States. Currently, there are 1,035 mines in operation.In 2016, then candidate Donald Trump promised to end the war on coal and to put coal miners back to work. In 2017, President Trump has followed up on those promises. He announced plans to withdraw the United States from the Paris Accord, signed an executive order designed to undo the Clean Power Plan put in place by President Obama, halted the research on the health effects of mountaintop removal coal mining, directed the U.S. Environmental Protection Agency (EPA) to revise the guidelines of waste water from power plants and has touted that more than 1,000 coal miners have returned to work since he was elected."

Jan 9, 2017

By Rodrigo Jerez

This paper describes a Mixed Integer Linear Programming model that was developed for planning the coal operations at Mountain Coals, Inc., in Kentucky. The model incorporates the use of stockpiles as practiced and allows the operator to find the least cost combination of raw coal feeds, washing densities and blending to produce the different quality coals as required by the coal contracts.

Jan 1, 1984

By Robert J. Greaves

High-resolution seismic reflection profiling can be used to evaluate detailed struc¬tural and stratigraphic features of coal pros¬pects. Since most coal prospects are relatively shallow (less than six hundred meters deep), the vertical and lateral resolution of seismic data can be significantly improved by high sampling rates in space and time. The case study present¬ed shows the effective use of seismic data in evaluation of the Wyodak coal at a prospective coal gasification site. The data were used to map the detailed structure and thickness of the coal and to search for lateral discontinuities, such as pinchouts and. faults. An important find was a paleochannel cutting across the base of the coal seam, which was later confirmed by drilling.

Jan 1, 1983

By N. S. Harding, M. C. Mai, A. G. Fonseca

Many coal characteristics affect combustion performance. Mill wear, boiler efficiency and derate, slagging, fouling, and ash collection and removal are only a few of the impacts of coal quality on boiler performance. The ability to assess fuel characteristic impacts on busbar costs is essential, although difficult to obtain. The relationships between coal characteristics and ignitability, operability, slagging, and fouling were investigated. The examination of combustion data/performance from a laboratory study, a boiler simulation system (pilot combustor), and commercial boilers indicated the benefits of burning improved quality coal. The specific effects of cleaning are discussed. A validation of the necessity of commercial-scale and/or pilot-scale testing is presented.

Jan 1, 1988

By J. C. Willett, J. R. Sanfilipo, P. D. Warwick

The U.S. Geological Survey has conducted an assessment of the Nation’s coal deposits that potentially could be mined during the next 30 or more years. For the Gulf Coastal Plain region, the assessment includes reviews of the stratigraphy, coal quality and resources, and coalbed methane potential of the Cretaceous, Paleocene, and Eocene coal deposits in the region. The results of these efforts are a series of digital maps, text, and tables published in CD-ROM format. Although abundant coal resources are available in the Gulf Coast region, coal quality issues may limit large-scale development in the future. Additional data are required to better evaluate the coalbed methane resource potential for the Gulf Coast region.

Jan 1, 2001

By Sharon G. Roness

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their: coal. Sulfur was the major concern. Btu content and sodium limited the market for some plants. The PRB market has now extended to plants that are converting from other coals because of the Clean Air Act. These new customers are more sensitive to constituents that affect boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to improve cost controls. Kerr-McGee Coal's Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998