Search Documents

By Haydn H. Murray

Common clay includes a wide variety of clay and other fine- grained rocks that are used in many ways. These clays are some- times classified as miscellaneous clay and shale. Most products made from them are fired and include such things as structural and face brick, drain tile, vitrified pipe, quarry tile, flue tile, conduit, pottery, stoneware, and roofing tile. Very large tonnages of these materials are bloated by firing to form lightweight aggregate, and large quantities are used in making portland cement (see the specific chapters in this volume). Uses not requiring firing of a finished product include filler for paint and other products and shale and clay used for packing dynamite in blastholes and for plugging oil and gas wells that are no longer in use.

Jan 1, 1994

By Haydn H. Murray, Fred G. Heivilin

The "Hormite Group" was proposed for palygorskite (attapulgite) and sepiolite for their complex magnesium silicate composition and elongate crystals (Martin-Vivaldi and Robertson, 1971). These minerals occur in close association with each other and more complex structural variations may exist (Bailey, 1972). In 1862 Savchenkov used the name palygorskite to describe a mineral from the Palygorsk locality (Hay, 1975), near the Ural Mountains. Ovecharenko and Kukovsky (1984) mention that when mountain leather deposits were prospected in the Palygorsk Division mine it was assumed this unusual mineral was a variety of asbestos. Early mineralogists used the terms "mountain cork" or "mountain leather" when referring to palygorskite. Robertson (1986) mentions that it appears palygorskite was known since Theophrastus&apos; time, ca. 314 BC. J. de Lapparent used "attapulgite" for clays from Attapulgus, GA, and Mormoiron, France, because he thought them different from palygorskite, but the two types were proved to be the same (Bailey et al., 1971). The name attapulgite is still used for the Florida and Georgia deposits when the crystal length to diameter ratio does not exceed 10:1(Merkl, 1989). Georgia palygorskite clays are of much shorter length compared to classic palygorskite. In 1847 Glocker first used the name sepiolite which was called "Meerschaum" by Werner (1788) and Hauy (1801) namedit "Ecume de Mer." Brochant (1802) described low density and white magnesium silicates adding the name Talcum Plasticum and Ecume de Mer. In the Meigs-Attapulgus-Quincy district palygorskite (attapulgite) commonly occurs in two distinct forms referred to as short length palygorskite (Meigs Member) and long length palygorskite (Dogtown Member) (Merkl, 1989). Long length palygorskite crystals (> 10 pm) are rarely observed in the Meigs and Dogtown Members, but when present are in association with dolomite crystals. The short length form is usually less than 2 pm in length and has a low magnesium content whereas the long length form has a high magnesium content and a length greater than 2 pm. The distinctions in morphology are not only important because of the relationship to the origin of the deposits, but also in relation to activity in causing membranolytic activity related to data on palygorskite samples from 9 locations ranging from relatively inert to active in work reported by Nolan et al. (1989). The > 10 pm lengths amounted to only 51 of 17,401 fibers sized. The shortest lengths (< 0.5 pm) were relatively inert. This study pointed out that surface activity, morphology, and chemical differences may be distinctly different within the definition of palygorskite, or for that matter for any individual mineral so that health and other properties must be measured because the name alone does not necessarily indicate uniformity. Palygorskite (attapulgite) fuller&apos;s earth was first sold for drilling mud in 1941. The market for this use expanded slowly and has maintained a level of 7 to 10% of the total US production during the last few years. Most of the fuller&apos;s earth sold for drilling mud comes from the southern part of the Meigs-Attapulgus-Quincy district of Georgia and Florida. Palygorskite clays produced in this area are superior to most other fuller&apos;s earth for mud used in drilling salt formations, but because of high water loss, they are inferior to bentonite where the rocks drilled contain no saltwater. According to Oulton (1965), more than 90 different grades of fuller&apos;s earth are produced. Some of these grades are used for pharmaceuticals designed to absorb toxins, bacteria, and alkaloids; for treatment of dysentery; for purifying water and dry cleaning fluids, dry cleaning powders and granules; for the manufacture of NCR (no carbon required) multiple copy paper; for the manufacture of wallpaper; and as extenders or fillers for plastic, paint, and putty. Fuller&apos;s earth mined near Ellenton, FL, was used for making lightweight aggregates for the construction of concrete barges during World War I1 (Calver, 1957). Still other uses of fuller&apos;s earth and its suitability for uses in new products are outlined by Haden, Jr., and Schwint (1967), Haden, Jr., (1972), and Haas (1970). One special use of fuller&apos;s earth is as a carrier of platinum catalysts that are made in the United Kingdom from sepiolite clays mined in Spain. Other uses of sepiolite fuller&apos;s earth (Chambers, 1959) are similar to those of the palygorskite (attapulgite) type mined in the United States.

Jan 1, 1994

By L. A. Arrington-Webb

Forty-four states produced clay products during 1994 for a total value of $1.6 billion. This was a 3% increase in total tonnage and a 7% increase in value from 1993. Kaolin Domestic production of kaolin during 1994 was estimated to be 9.3 Mt (10.2 million st), according to the US Bureau of Mines (USBM). Georgia remained the leading producer with 7.5 Mt (8.2 million st), followed by South Carolina with 535 kt (589,000 st). Kaolin used as a paper coating or filler pigment accounted for 51% of domestic consumption. Other uses included grogs (14%), fiberglass (5%) and plastics (4%). A reclassification by an Alabama producer of fire clay to kaolin accounts for the introduction of kaolin used in grogs. This also accounts for the apparent decrease in the use of kaolin in paper from 60% in 1993. However, the actual amount of kaolin used in paper was the same.

Jan 1, 1995

By G. W. Luxbacher

Acid rain legislation included in the Clean Air Act Amendments of 1990 caused a great deal of uncertainty regarding the price, source and production quantities of coal supplied to the eastern coal market. Powder River Basin and other western coals continue a rapidly accelerating migration eastward. South American coals move into the northern markets. States are proposing legislation to assist utilities in complying with the new regulations in hopes of maintaining their own coal industries. Some utilities question the long-term availability of eastern compliance coal. Major coal producers must make decisions now to assure their continuing presence in the market place. Several companies have adopted a strategy to acquire eastern compliance reserves, while others have invested in technology to compete as a low-cost producer. Legislation "Acid rain." This is a topic that was debated within the scientific, environmental and industrial communities for years. Those discussions resulted in a large outlay for the federal National Acid Precipitation Assessment Project (NAPAP), which was then ignored. Acid rain then became the subject of a "60 Minutes" broadcast that debunked the acid rain theory, supporting the NAPAP study conclusions. In the final outcome, however, acid rain was the driver for the Clean Air Act Amendments of 1990.

Jan 1, 1992

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By L. L. Anderson

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70 percent of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than 1/2 inch) tubes and at reaction residence times of less than 10 seconds. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1975

By C. V. Baltzer, E. L. J. Bingham

Compliance with the EPA&apos;s emerging Clean Water Act regulations can be challenging. Open pit copper mines in Arizona have found themselves in a tangled web of changing rules, regulations, and guidance documents regarding storm water and process water discharges. Large mining properties must come up to speed on a myriad of issues including the definition of zero discharge, what constitutes a process related spring or seep, and tailings and waste rock Best Management Practices. The example of the Pinto Valley Mine in Arizona is used to illustrate National Pollution Discharge Elimination System regulatory issues.

Jan 1, 2001

By Florence Munter

This paper provides a discussion of the various federal and state laws governing water quality as related to mining operations. The specific laws addressed are the Clean Water Act, and the Arizona Mined Land Reclamation Act. Topics that will be addressed are mine water and process water discharges, storm water discharges, pollution prevention, dredge and fill, spill prevention control and countermeasure plan, and surface water protection. Proposed changes to the laws and regulations will be discussed. Compliance strategies will be suggested to prevent potential noncompliance and enforcement.

Jan 1, 1996

By G. M. L. Robinson

The Clean Water Act, as administered by the Environmental Protection Agency, has mandated industry, government and the public to comply with potentially conflicting and vague water quality statutes, regulations and guidelines. Universal regulatory strategies have been developed which have introduced and have created regulatory, compliance and institutional conflicts. Conflicts have been created because National water quality performance goals and design standards are vague, and, in many cases, cannot be scientifically justified. Because of regulatory technical requirements to define background and environmentally impacted water quality characteristics, the ability to achieve regulatory compliance is difficult. Difficult issues requiring resolutions includes but are not limited to site specific surface and ground water quality classification systems, water quality standards and guidelines, point and non point pollution sources etc. Because of these statutory and regulatory complexities, a confrontational regulatory system has been created as it relates to: - defining performance criteria in relation to design criteria; - resolving water quality statistical compliance conflicts; - defining laboratory precision requirements; - determining background groundwater characteristics; and - locating a representative point of compliance. Because of these complex regulatory issues, the ability to balance goals, needs and economics has not been achieved or in many cases has not been attempted, without legal intervention. A few examples illustrating where water and waste management compliance conflicts have been experienced.

Jan 1, 1992

By Renee Y. Allee

The Chino open pit mine, concentrator, and smelter are located in Grant county in Southwestern New Mexico. Chino Mines Company is a partnership, two- thirds owned and operated by Kennecott Santa Fe Corp., and one third owned by MC Minerals Corp. (Mitsubishi) of Japan. The concentrator, with a design capacity of 37,000 tons of copper-molybdenite ore per day, was commissioned in July, 1982. Further design modifications have resulted in an increase in throughput capacity to 42,000 tpd

Jan 1, 1986

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, Y. Xiong, J. Gu

"As ores degrade, mining techniques and chemistries change to meet market demand and maintain product quality. The balance of recovery and grade is a significant challenge in the Crago Process where an anionic collector is used to float phosphate, followed by acid scrubbing, then an amine float to improve product grade. As the grade is a requirement for DAP and MAP production, recovery is the criteria to suffer. Phosphate losses in the amine float can bring overall recovery down by as much as 18%, creating a growing need to think outside the box to improve recovery. This paper will focus on the theory of amine tail recycling and the best methods to optimize the overall phosphate recovery by recycling the tails from the cleaner flotation step. INTRODUCTION In 2014 the total US phosphate production was down 13% over the prior year, from 31.9 to 27.1 Mt, which accounts for 12.32% of the world’s phosphate rock production. Florida and North Carolina phosphate production accounted for 80% of total US phosphate production, which was down from 85% the previous year. This decline is due in part to the closing of the last phosphate mine in Polk County, FL - which had an operating phosphate mine for over 100 years (Gurr, 2015). Another factor contributing to the reduction in contribution from FL & NC is the increasing challenges in beneficiating the remaining ore deposits. The Central Florida mining district has historically been in the Bone Valley deposit, where raw apatite was abundant with P2O5 values as high as 15%. The Bone Valley ore also had characteristics favorable to beneficiation to 27.5-29.7 %P2O5 while achieving recoveries above 86%. The move southward into the Hawthorne Formation has seen the ore feed grade hit some historic lows, and the matrix characteristics pose more challenges to phosphate producers. The Hawthorne Formation experienced lateritic weathering after the Bone Valley formation which altered the apatite to aluminum phosphate minerals, and alteration of montmorillonite to kaolinite, releasing MgO that caused the dolomitization of the top of the Hawthorne limestone (Cathcart, 1966). Elevated levels of dolomite can yield an increase in slurry viscosities, reduce production rates, and increase energy costs in the wet-acid fertilizer process. The MgO will also act to dilute grade, making it more difficult to achieve a standard 18-46-0 product (McHardy, 1981)."

Jan 1, 2016

By K. S. Eric Forssberg, Lennart Ryk

The paper discusses coal utilisation in Sweden. All hard coals have to be imported from other countries. Peat from domestic sources is used as a complement. Environmental legislation and taxation on fuel and emissions are severe. This situation affects the procurement, preparation, handling and use of coal. The paper presents: • R&D projects concerning deep cleaning of thermal coal. • Handling and treatment of coal used in PFBC boilers and for blast furnace injection • Dust prevention for coal and peat briquettes. Procurement of coal emphasising quality and environmental issues.

Jan 1, 1995

By Joseph Alexis

Humphreys Engineering Co. has been associated with mining and milling since the turn of the century, but its greatest contribution to the industry was development of the Humphreys spiral concentrator in 1943. Few devices in the history of mineral beneficiation have been so uncomplicated. The spiral concentrator has no moving parts and requires no power except that needed to deliver slurry to the feed box, a requirement common to all concentrating devices. Although Humphreys Engineering Co. produces several models of spiral concentrators, the one -commonly used for coal cleaning is Model 24C-6 which has a flatter pitch than most other models. The spiral concentrator consists of a spiral conduit with a modified semicircular cross section. A slurry containing 20-35% solids by weight is fed to the feed box at the top of the spiral and flows downward. The heavier refuse particles concentrate along the inner side of the slurry stream and the lighter coal moves to the outside. The coal spiral has six complete turns-each turn consists of three 120°-sections and each section has a refuse port at the lowest point of the channel. The Humphreys spiral concentrator separates minerals in accordance with their physical properties (primarily specific gravity and particle shape). Aside from pumping slurry to the distributor, no energy is required to produce clean coal since the separating action is controlled by gravity. As slurry flows down the spiral channel, each particle is subjected to a centrifugal force, tangential to the channel. This force piles slurry on the outer rim of the spiral until the flowing stream reaches an equilibrium between outward centrifugal force and downward gravitational force. Once established, the stream position is relatively constant. In any flowing stream, differential velocities are present within that stream (the slowest fluid levels nearest the channel surface and the fastest layers at the center). As the channel curves, the lower slurry levels, retarded by friction, have much less centrifugal force and tend to move sideways toward the inner radius of the channel. As the bottom layers move inward along the bottom of the channel, the upper layers must move outward to maintain equilibrium. This cross sectional rotation separates the minerals and moves those of highest specific gravity toward the inner radius where they drop through refuse ports (see figure on following page). The simplicity of the spiral concentrator is apparent in operation. After tonnage, slurry volume, and percent solids of the feed have been determined-generally with laboratory testing-the operator&apos;s main concern is simple adjustment of the splitters located in the refuse ports. These splitters control the amount of refuse collected and, generally, once properly set they need little attention unless grade conditions drastically change or trash builds up and hinders laminar flow. Spiral concentrators are not overly sensitive to changes in pulp densities, variances in grade, or parti¬cle size and shapes. All these conditions may fluctuate over fairly wide ranges without adversely affecting recovery and product grade. In certain applications, desliming may improve recovery.

Jan 8, 1980

By Verya Nasria, William Bent, William Hogan

"The South Hartford Conveyance and Storage Tunnel (SHCST) project is a significant component of the Hartford Metropolitan District’s (MDC) long-term control plan (LTCP), which is overseen by the Connecticut Department of Energy and Environmental Protection (CTDEEP). This project will address a portion of the MDC’s Clean Water Project (CWP), which will reduce combined sewer overflows (CSOs), eliminate sanitary sewer overflows (SSOs), and reduce nitrogen released into the Connecticut River. The purpose of the SHCST project is to eliminate West Hartford and Newington SSOs, eliminate Franklin area CSOs discharging to Wethersfield Cove and minimize CSO discharges to the South Branch Park River. The locations of each overflow are shown in Fig. 1. In 2010, the district prepared a preliminary design report (PDR) for the SHCST project, which included relief of the Folly Brook trunk sewer and proposed to keep the tunnel boring machine (TBM) retrieval shaft within the city limits of Hartford. Figure 1 shows the 2010 PDR recommended tunnel route. Subsequent to the PDR, the objectives of the SHCST have slightly shifted. In accordance with ongoing revisions to the LTCP, relief of the Folly Brook Trunk Sewer is no longer necessary. Additionally, the MDC has decided to perform less sewer separation in the Franklin Avenue drainage area. To replace the sewer separation, new relief points are proposed within the Franklin area and will be diverted to the SHCST. Figure 1 also shows the current recommended tunnel route (Alignment F). During 2012, the MDC conducted an evaluation of the potential of connecting the proposed North Tunnel (originally proposed as an independent tunnel with its own pump station) into the South Hartford Conveyance and Storage Tunnel. This evaluation concluded that the two proposed tunnels could reasonably be connected together and operated as a single tunnel system utilizing the tunnel pump station at the eastern terminus of the South Hartford Tunnel (Fig. 2). It also was concluded that this alternative was less costly than two independent tunnel systems."

Jan 1, 2014

By Bob Clayton, David Readett

Jameson Cell technology has found applications in the cleaning of entrained material in copper Solvent Extraction - Electrowin plants. The materials involved are largely organic substances that have not been totally removed prior to treatment of the rich electrolyte in the tank house. This paper discusses the recovery of the entrained organics in the rich electrolyte streams at Phelps Dodge Morenci in Arizona. Mount Isa Mines in Queensland. Australia and the Olympic Dam Operations in South Australia. The paper details the design, performance, the feed and product characteristics, capacity and operation. In one operation the entrained material has been observed to include crud that has been formed in the SX train. The mechanism of recovery is also discussed.

Jan 1, 1993

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

By Donald J. Reining

The California Surface Mining and Reclamation Act (SMARA) is the nation&apos;s first legislation establishing a statewide mineral resource policy governing mining activities that recognizes regional needs and retains local autonomy. The Southern California Rock Products Association supported this proposed legislation. It was through our efforts that SMARA was passed in 1975. The local planning and zoning processes, which are so critical to the mining industry, have been significantly improved with implementation of SMARA. Recognition of the importance of the mining industry is now being developed by the State Mining and Geology Board and the California Division of Mines and Geology (CDMG).

Jan 1, 1984

By John A. Brooks

The description of a phosphate flotation operation is repeat information for many people, except for variations in flow sheets. This paper is written to show the variations in flows, and to give enough. of the overall flows to allow anyone not familiar with the operation to be able to formulate a fair idea of the operations.

Jan 1, 1962