Search Documents

By W. D. Presley, T. R. Harrell

This paper will be a case history of the shaft and tunnel concrete lining techniques used at the Rocky Mountain Pumped Storage Project located in northwest Georgia. Emphasis will be placed on the shaft lining techniques with only a brief description of the tunnel concrete lining techniques. The 10.67 meter (35 foot) diameter shaft and tunnel concrete linings are 0.61 meter (2 foot) nominal thickness with a single row of reinforcing bars. The tunnel was placed in 18.29 meter (60 foot) lengths with bulkheaded end sections. The 172.72 meter (566.68 foot) vertical shaft was placed in 3.05 meter (10 foot) high sections using jump forming techniques.

Jan 1, 1985

By D. E. Hart, A. R. Walsh, Derek Maishman

In order to safely construct a ventilation and escape shaft through saturated overburden into an operating mine, artificial ground freezing and raise boring were combined for the first time on a project in the U.S.A. at Georgia-Pacific's Kentwood Mine in Grand Rapids, Michigan. Previous to drilling a pilot hole 206 feet deep into the mine, a 20 foot diameter cylinder of soil 140 feet deep was totally frozen. Before termination of the freezing operation, the pilot hole was reamed to 9 foot diameter and a 7 foot inside diameter hydrostatic steel liner was grouted in place.

Jan 1, 1991

By Jeremy Cawley, Horry Parker Jr., Clint Wilson

The 5180 m EPBM drive on the Lower Olentangy Tunnel (LOT) is predominantly within glacial overburden. To connect LOT with the existing OARS deep tunnel in limestone bedrock, the upper 15 m inside diameter Vine Street retrieval shaft telescopes down to 6.7 m in diameter and extends into the karstic Columbus Limestone to a depth of 51 m, where a 104 m SEM tunnel will connect to OARS shaft 6. Pre-excavation grouting was reuired prior to lower shaft excavation to reduce potentially high groundwater inows. This paper discusses the secant pile installation, grouting program, shaft excavation, and hydrogeologic observations.

Jun 23, 2024

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By Dale J. Sadowski, Richard J. Switalski, Kyle R. Ott

This paper discusses design and construction aspects of shaft construction through rock saturated with petroleum hydrocarbons (crude oil). During the subsurface exploration phase for design of the Hilltop Interceptor project in Cleveland, Ohio natural crude oil was encountered at depths between 6.1 and 61 m below ground surface. The oil-saturated Euclid sandstone contained up to 12,000 mg/kg total petroleum hydrocarbons (TPH), various volatile organics, and had flash points as low as 18.9°C. Interceptor hydraulic design required that construction of access and/or drop shafts penetrate the layer of petroleum hydrocarbon saturated rock. This led to the design of a special lining and some special handling procedures for the excavated material.

Jan 1, 1995

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024

By Kot F. Unrug

When reading different studies discussing trends in coal mining, it appears that a substantial expansion of output by the year 2000 is predicted, even in the most pessimistic forecasts. Depletion of shallow, easy-to-mine deposits is only a matter of time, and the future average mining depth will increase. The proportion of slope to shaft mines operated during the next decades will change in favor of the shaft mines. Since an increasing amount of shafts in new nine developments seems to be inevitable, it appears appropriate to focus more attention on shaft design criteria. Some valuable papers have recently been published (1) that emphasize geotechnical aspects of shaft design. In the discussion that follows some other aspects of design criteria will be evaluated.

Jan 1, 1984

By Dale A. Bivens

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is currently being constructed for the United States Department of Energy in SE New Mexico. The purpose of the project is to store low level transuranic waste in an underground environment which will ensure a safe atmosphere for the life of the stored waste. Ohbayashi was contracted by the DOE to sink two shafts and underground drift development which will be used to conduct a series of long term experiments in order to finalize the suitability of the geology and the environment for the transuranic waste storage. The two shafts sunk at the WIPP site were excavated around a borehole by conventional methods. The excavation around a borehole eliminates some of the established blind bottom sinking techniques, but creates unusual problems which must be pre-planned and scrutinized closely. An analysis of the slashing to the borehole technique will be given. WASTE SHAFT The waste shaft (w/s) is 5.8 meters (19 feet) in diameter and will be used primarily to transport the radioactive waste to the underground storage area. A pre-existing 1.83 meter (6 feet) diam borehole was taken to a depth of 655 meters (2150 feet) to the existing drift; at this level, a 38 meter (125 feet) sump was installed using blind bottom sinking techniques. Geology The primary geology for the w/s excavation is redbeds, anhydrites, dolomite, mudstone and

Jan 1, 1985

By A. S. Moss, J. Linkous

Where difficult shaft sinking conditions exist, it may be appropriate to use a blind drilling technique. The success of the method is in part due to the presence of a drilling mud which fills the shaft void during excavation. The mud performs two important functions with respect to shaft stability: it reduces the influence of groundwater; and, due to the mud weight, gives a positive sup- port to the shaft walls. The application of the method is illustrated by a case history which traces the development of a shaft from the initial investigation to determine the shaft location, through the evaluation of wall stability and mud requirements, to the shaft sinking contract and actual conditions encountered.

Jan 1, 1986

By V. L. Magnus

The text of this chapter was not received in time for printing.

Jan 1, 1979

By Thomas E. McNider

Preliminary studies were conducted at Jim Walter Resources, Inc. Blue Creek No. 3 Mine to determine the influence propane operated heaters exert on the mine ventilation system when two of three intake airshafts were heated. During initial use of the heaters, it was found that change in density caused by heating a portion of the air at two of three intake shafts altered under- ground air flow changes sufficient to be considered a violation of Part 75.322 of the Federal Coal Mine Health and Safety Act of 1969 as amended by Public Law 95.164. The primary concern was to accurately define the problem in order to derive a workable solution.

Jan 1, 1980

By Bruce C. Schepens

The Balsam Meadow Hydroelectric Project is currently under construction in central California. TMCI Construction, Inc. was subcontracted to perform the shaft enlargement and lining required for the elevator, surge and power shafts. Involved in the initial work was slashing the elevator and surge shaft into a previously excavated borehole. The elevator shaft then required a reinforced concrete lining and structural steel installation. Throughout the course of construction, numerous design changes occurred, necessitating a lining in both the power and surge shafts. These changes caused TMCI to design two underground hoisting systems to install these additional linings. An analysis of the construction methods used is now given. Introduction The Balsam Meadow Project consists of an underground hydroelectric powerhouse designed to provide additional capacity and energy to the Southern California Edison system during critical peak demand periods, and has the capability for pumped storage operation. The project is located in the Sierra Nevada Mountains about 55 miles northeast of Fresno. The project will divert water presently flowing from Huntington Lake to Shaver Lake to power a single 200 megawatt turbine generator. The approach used to the shaft slashing was governed partially by the strict CAL-OSHA requirements, which became more stringent after the recent Helms' Creek accident. A scaled down sinking plant was used to minimize economic risk and to simplify the excavation and lining scheme.

Jan 1, 1987

By S. A. G. Poppen

The lining of a mine shaft is one of the most important considerations in the planning and operation of an underground mine. Generally, the function of a shaft lining is to preserve the shaft opening in a manner compatible with the expected mine life and -the other shaft operations. Where shafts are the only means of surface access in a mine, they also serve a critical function for the safety of the entire underground operation. Routine repairs and maintenance work on the shaft linings are only possible in stable strata with only minor interruptions to the shaft operations.

Jan 1, 1988

By W. R. Dengler

INTRODUCTION Shaft sinking represents a relatively small proportion of the activities involved in mine development. Because of this limited utilization, shaft sinking has been one of the most difficult functions to mechanize. Although shaft machines (muckers) were introduced more than 30 years ago, the first machines were low-capacity units, and machines of this type did not gain wide acceptance by the mining industry until the late 1950s. However, the increasing depth of underground mines and the es¬calating costs of labor have increased the benefits obtain¬able from high-speed shaft sinking. The result has been a growing need for high-capacity shaft machines. Most of the machines available at the present time have been developed by modifying existing equipment to increase the payload capacity and performance. AVAILABLE SHAFT MACHINES In general, shaft machines may be classified accord¬ing to the types of digging mechanisms and the mecha¬nisms of operation. The available digging mechanisms include clamshells, cactus grabs, front-end buckets, and backhoes. The mechanisms of operation can be classified as either pneumatic or hydraulic. Selection Criteria For efficient operation, the primary consideration in selecting a shaft machine is its capacity. The minimum capacity of the machine should match the capacity of the hoisting system at the ultimate depth of the shaft. In many cases, two machines may be needed to obtain a sufficient mucking capacity. The shaft dimensions and configuration often dictate the type of machine that may be utilized; for example, an overshot loader does not work well in a circular shaft that has a diameter of less than 5.5 m (18 ft). Similarly, a single Cryderman mucker is not suitable for a large-diameter shaft, nor is it applicable where very high sinking buckets are to be used. Other factors for consideration include the degree of material fragmentation, the abrasiveness of the rock, and the amount of ground water that is inter¬sected. Machine Descriptions Riddell Mucker: The Riddell mucker, illustrated in Fig. 1, was first introduced in 1948. This is one of the most common shaft machines in the medium-capacity range. The Riddell mucker consists of a hoisting and traveling mechanism that operates a clamshell suspended on cables. The early machines operated with a 0.3 m3 (10 cu ft) clamshell and had an hourly capacity of approximately 27 t (30 st). This type of shaft machine has gained wide acceptance throughout North America. Essentially, the Riddell mucker consists of standard components, such as the pneumatic tugger hoists that operate the clamshell. The carriage is suspended on rails that also serve as the blasting set, located immediately below the shaft timbers. To effectively position the clam¬shell in the shaft, the operator controls the carriage travel by means of wheels that are driven by a pneu¬matic motor. The Riddell mucker most commonly is used in rec¬tangular timbered shafts. However, some units have been installed with circular rails, allowing them to work in circular concrete-lined shafts. A popular practice with many Riddell muckers is to increase the capacity through the use of larger clamshells, often ranging up to 0.76 m3 (1.0 cu yd), in conjunction with more powerful tugger hoists. In some large rectangular shafts, two Riddell units have been used side by side to achieve a sufficient capacity. Cryderman Mucker: The Cryderman mucker, illus¬trated in Fig. 2, is another common shaft machine in the low- to medium-capacity range. Developed in the early 1950s, it also has gained wide acceptance throughout North America. Equipped with a 0.3 m3 (10 cu ft) bucket, the Cryderman mucker has an hourly capacity of approximately 23 t (25 st). The Cryderman mucker is operated entirely by means of pneumatic cylinders and a pneumatic telescopic boom. The boom is suspended from a sectional frame¬work that is usually located at one end of the shaft. The framework or headframe can be suspended from an independent hoisting system located either on the sur¬face or in the shaft. In large shafts of either rectangular

Jan 1, 1982

By D. W. Alexander

In 1993, CONSOL began investigating new methods of permanently filling coal mine shafts, which after ventilation is stopped, may contain a potentially hazardous atmosphere. Fill materials such as fly ash/cement can be pumped, are non-combustible and non-incendiary but tend to flow into the mine entries. A non-flowable mixture has been developed that minimizes the volume of fill used. The paper presents our recent shaft filling experience including fly ash material properties, mix designs, field problems, placement success, and gas testing techniques.

Jan 1, 1996

By J. W. MacDonald

Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review, These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work.

Jan 1, 1960

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation.

Jan 1, 1981

By Ralph Musick, Brian Briggs

The U1h Shaft Project is a design/build subcontract to construct one 6.1 meter(m) (20 feet [ft.]) finished diameter shaft to a depth of 321.6 meters (m) (1055 ft.) at the Nevada Test Site (NTS). Atkinson Construction was subcontracted by Bechtel Nevada(BN) to construct the U1h Shaft for the Department of Energy (DOE). The project consists of furnishing and installing the sinking plant, construction of the 321.6 m(1055 ft.) of concrete lined shaft, development of a shaft station at a depth of 297.5 m(976 ft.), and construction of a loading pocket at the station. The outfitting of the shaft and installation of a new hoist may be incorporated into the project at a later date. This paper will describe the design phase, the excavation and lining operation, shaft station construction and the contractual challenges encountered on this project.

Jan 1, 2001

By Andreas Prucker

The Greater Vancouver Water District (GVWD) is currently constructing the largest water treatment plant in Canada. As part of this treatment scheme twin water transfer tunnels are being constructed. Work commenced with the 11 m diameter, 185 m deep Seymour Shaft which was excavated by drill and blast using a mobile crane for hoisting. The Seymour Shaft is the first large diameter shaft that has been sunk in Western Canada in recent years. The operational aspects associated with the hoisting, the drill-blast-support cycle and water control in the shaft are the focus of this paper.

Jan 1, 2008