Search Documents

By Joel K. Waterland

The Homes take Mining Company at Lead, South Dakota has a yearly production of 1,868,741 tons of ore produced from horizontal cut-and-fill stopes and timber cut-and-fill stopes. This production, in addition to the necessary development (drifts and raises), requires 5,168,271 feet of drilling annually. The rock for the most part consists of quartz; mica schist; and cummingtonite schist; and must be considered as relatively hard. Penetration rates average about 15 inches per minute using an operating air pressure of 100 psi. The rock is tough, rather than brittle, and dulling occurs quite rapidly. The average regrind period is approximately 19 feet per regrind using a 1-7/16 inch carbide bit. At the present time, all drilling is accomplished with 2-5/8 inch bore airleg mounted drills, and 2-3/4 inch and 3-inch diameter bore -stopers (raising only). These machines are all direct striking, with 4-1/4 inch chucks. 7/8-inch hexagonal carbon drill steel with forged collars are used in conjunction with 1-7/16 inch multi-use, threaded, carbide bits. 62,793 rods, and 16,234 bits are used to maintain the yearly production. The number of rods noted are the rods that were sent: underground, both new and reconditioned.

Jan 1, 1963

By Russell L. Dahl

In a continuing effort to improve plant efficiency, United States Steel's Atlantic City Ore Operations completed the rubber lining of its balling drums in late 1982. This resulted in benefits of reduced bentonite consumption, reduced maintenance costs, improved production rates, and lower power consumption. These advantages far outweigh the disadvantages of increased oversize production and increased surging on the roll screen sizing devices. Certain operating characteristics and variables are discussed herein.

Jan 1, 1983

By Christopher J. Bise

INTRODUCTION Face haulage in underground mines and pit haulage in surface mines are the principal domains of rubber- tired haulage vehicles. In underground mines, cable- reeled or battery-operated shuttle cars and diesel-powered load-haul-dump vehicles are used; trucks are primarily used in surface mines. Although many concerns go into the selection of rubber-tired haulage vehicles, such as clearance and tire life, the most important factor from a mine-planning standpoint is the production capability of the vehicle in the mine environment. Therefore, this chapter will address this topic. UNDERGROUND FACE-HAULAGE VEHICLES The selection process for underground face-haulage vehicles is, in some respects, much simpler than that of the other haulage systems discussed to this point. It is simpler because these vehicles, which transfer the mined material from the face to the intermediate haul¬age system, are manufactured in various size ranges to cope with the confinement of underground opening widths and heights. However, since these vehicles oper¬ated in an intermittent fashion in conjunction with a constantly advancing face, the system's lack of perma¬nence and overall dynamic nature create a more diffi¬cult situation for predicting productivity. The emphasis in this section will be on prediction of productivity. There are three fundamental steps that must be taken to analyze the productivity potential of any face¬haulage system: l) Recognize the geologic (seam thickness, etc. ) and mining (opening widths, etc.) constraints that affect the velocity/clearance aspects of the haulage equipment, and select equipment from manufacturers' specifications with these con¬straints in mind. 2) Secure the elemental times of the face-haulage system. 3) Incorporate the elemental times into an accepta¬ble mine plan. By recognizing the geologic and mining constraints that affect the system layout, parameters, such as vehi¬cle payload, tonnage to be hauled per cut, and haulage distances, can easily be determined. Elemental times can be developed in two ways: 1) In an existing operation, a time study of the dynamic system can be conducted by placing three time-study engineers at the following static locations; (1) near the loading machine, (2) near the change-out point outby the face, and (3) near the dump. By synchronizing their watches and recording the actions of the haulage vehicles at these three locations, their time studies can be reduced to provide elemental times, such as vehicle tram rates (empty or loaded), vehicle discharge times, and loading rates. 2) In the absence of an existing operation, average values for the elemental times can be provided from other mines operating in similar condi¬tions, or by the manufacturers themselves.

Jan 1, 1986

By Hung-Kei H. Lam

Rubidium and cesium were discovered by Bunsen and Kirchhoff about 100 years ago. These two elements are by no means as abundant as sodium or potassium. Their occurrence in minerals is widespread, but usually as minor constituents. There is no known specific ore containing rubidium, but rubidium is found replacing the. other alkali metals in .some minerals.. Perhaps the highest concentration of rubidium found in one mineral is in lepidolite, KLi(OH,F)2A12Si3010, which contains from 0 to 3.5%*Rb20. 0n the average, lepidolite contains about 0.5% Rb20. Other sources of rubidium are carnallite, KMgCl3?6H20; pollucite, H20.2Cs20.2AI203.9SiO2; rhodizite, R20.2A1203-3B203; biotite, H2K(Mg,Fe)3A1(Si04)3; sea water, rivers, marine and fresh water organisms, soils, and plants. Cesium, even though it is the least abundant. of the stable alkalies, has a specific ore. Pollucites a hydrous cesium aluminum silicate, may con¬tain as high as 42.5% Cs20, although again, the average Cs20 content is about 25% among the handful of known deposits. Other cesium-containing minerals are lepidolite and carnallite. Rubidium and cesium are very much like potassium in chemical properties, consequently, they are hard to separate. Because of the difficulty in obtaining pure cesium and rubidium compounds coupled with the scarcity-of supply, prices were high and the two elements enjoyed little industrial use. Just before the Second World War, the world. supply of rubidium and cesium, from Germany, was a matter of tens of kilograms per year and prices were about

Jan 1, 1959

By John R. Twining, Michael D. Lawton, Ross A. Jeffree

The Finniss River system in tropical northern Australia has received 'acid-drainage' contaminants from the Rum Jungle uranium/copper mine site over the past 4 decades. Following mine-site remediation that began in 1981-82 the annual contaminant loads of sulfate, Cu, Zn and Mn have declined by factors of 3, 7, 5 and 4, respectively over 1990-93, compared to the 1969-74 pre-remediation loads. Comparison of the frequency distributions of contaminant water concentrations over these pre- and post-remedial periods have shown varying degrees of reduction in the highest levels following mine-site remediation, that are consistent with reductions in their annual-cycle loads. Among the three selected major metal contaminants the reductions in maximum water concentrations are most pronounced for Cu. The demonstrated reductions in the highest water concentrations of all four contaminants are also associated with previously reported ecological improvement in the Finniss River system, compared to the benchmark of environmental detriment established in 1973fl4, prior to the beginning of remediation at the mine site.

Jan 1, 2000

By T. Braun

A greenfield open pit gold mine in Latin America suspended operations less than three years into an eight-year mine plan after a waste rock dump and heap leach facility sustained substantial damage from a deep-seated landslide. No injuries to employees were recorded because of the slow-moving failure. Due to early detection by the operations team, the owner had sufficient notice of the potential failure and successfully rinsed the heap leach facility prior to the failure event. Engineers estimated approximately 35 million cubic meters of mass movement below the waste rock and heap leach facilities. The original eight-year mine plan produced approximately 60,000 ounces of gold per year. After the failure, the owner terminated gold production, re-configured the mine site to a safe, standby condition and launched a detailed investigation into the root-cause of the failure. Approximately two years after the shutdown, legal interests filed a statement of claim and named three engineering design firms and individuals involved in the project. Several years of litigation, including discovery and deposition proceedings, followed as the legal process considered evidence spanning a 20-year timeline. Changes in project ownership and consulting firms during the development and operations phase complicated the process. In 2017, the plaintiff and last defendant settled. The author was involved as the corporate representative for one of the engineering design firms.

Mar 2, 2022

The day after I reached New York, on January 30th, John Ryan of Anaconda told me where they wanted me to go. Late in 1916 the Russian Czar, desperate for money and supplies with which to carry on his unhappy share In the first World War, sent emissaries to the United States to see if our great mining companies might be interested in trying to find mines and to bring them to production in the millions of acres of the Imperial Estates in Russia and Siberia. It looked like a long chance as no one knew whether or where there might be important ore bodies. Even if they found them it might be a hopeless task to equip them under wartime conditions But the American copper companies had plenty of money and they were used to taking risks. They made a supersecret agreement with the Czar's deputies to send an exploring expedition to Russia at once I never learned the names of the other companies but Anaconda was to man- age the venture. Horace Winchell, then the leading mine geologist In the United States, was to be in charge of operations. Charles Janin, an eminent placer and dredge expert, was to study chances for producing gold and platinum. Though at 33 years of age I was much younger than the others, I was chosen to hunt for copper and other valuable metals. Charles Boynton, a business man who had lived in Russia and had married an attractive Russian woman, was to join the party and carry on any necessary financial or diplomatic affairs. He had gone on ahead to arrange for our reception Finally a graduate student from Ann Arbor named Steinberg was to go along as Interpreter. We soon found out that if his Russian was no better than his English his interpretlng couldn't be trusted too much I knew nothing about the millions of square miles In Russia and Siberia, and even less about what mineral deposits might be found, but I was delighted at the prospect. I was treading on air for the few

Jan 1, 1976

By Frank J. Skudrzyk, Vladimir F. Petrov

In compliance with the current Russian environmental legis­lation, possible impact of industrial activities on the environment is restricted by acceptable limiting values (maximal allowable concentrations - MAC) of individual chemical substances in the natural environment - water, atmospheric air and soils. These norms have federal status and are valid for the whole territory of Russia. Disposal of the substances, for which no MAC is estab­lished, is forbidden by the law. Many gold mining companies use cyanide in precious metal recovery. This paper overviews the Russian experience in pro­tection of natural water reservoirs from technogenic impact of cyanic technologies. Major toxic compounds, contained in liquid and solid rejects from hydrometallurgical treatment of gold ore using cyanidation, are cyanides (CN), thiocyanates (SCN) and cyanide metal com­plexes. Unlike western classification of various cyanide types, in Russia any inorganic cyanide compounds (simple and in com­plexes with metals), with the exception of iron cyanide com­plexes, are considered toxic and the acceptable limiting value is established for them. MAC is 0.05 mg/I for fish reservoirs and 0.1 mg/I for drinking water. For iron cyanide complexes MAC is 0.15 mg/I for fish reservoirs and 0.25 mg/I for drinking water. Russian norms for thiocyanates are practically as rigid - the acceptable limiting value for them in fish reservoirs is at the level of 0.07mg/l (0.15 mg/I for potassium thiocyanate) and for drinking water - O. lmg/1. Norms for metals are established on the basis of total content regardless of the form in which they are present in water - as cations or complex ions. It should be noted, that in case several toxic compounds of the same limiting value (for cyanides, thiocyanates and base metals the limiting value is toxicological) are present in water. Their allowable concentra­tion is calculated as the sum of actual concentration of each com­pound, divided by the corresponding acceptable limiting value, with the result not to exceed one (compounding effect). Differences in cyanide classification and the necessity to include thiocyanates dictate different analytical methods. This, in a number of cases, results in certain discrepancies in analytical results. Until recently chlorination was used as a basic process of detox­ification of wastewaters. Calcium hypochlorite powder or hypochlorite pulp, prepared of lime milk and chlorine shipped to the plant, were used as a reagent. Chlorination is an efficient method: it allows to completely destroy plain and complex cyanide, in addition to iron complexes, and thiocyanates. A good example of high efficiency chlorination can be found at the Mnogovershinniy mill near the Okhotsk Sea located in the salmon spawning area, for which we designed an automated chlorination plant for tailings dam. Since plant start-up ten years ago, the required concentrations of cyanides and thiocyanates have been kept at the MAC level required by environmental regulatory agen­cies and no harmful affects on ichthyofauna has been reported. One major drawback of chlorination is high cost of the major reagent, as well as secondary contamination of detoxified waters by chlorides. Secondary contamination by chlorides becomes obvious in the course of detoxification of wastewaters of com­plex composition, which require increased reagent consumption. Recent changes in economic conditions in Russia caused the necessity to direct efforts to reduce the costs of precious metals recovery, and in particular, wastewater treatment. We have con­ducted certain work in this direction and obtained positive results. We hope that our experience described below will be of interest to other specialists particularly taking into account the current low gold prices.

Jan 1, 1998

By Lech Bolinski, Joe Shirley

Over two dozen Resin-in-Pulp (RIP) plants have been in operation in the fonner Soviet Union since the beginning of 1970. Currently approximately 50% of the gold produced in Russia, Uzbekistan and Kazakhstan, which equates roughly to 10% of the total world output, is recovered using the RIP technology. An alternative to activated carbon, ion-exchange resin has several advantages for the recovery of gold. Resins are less prone to clay or organic foul­ing and do not require thennal regeneration. They also have poten­tially higher loading capacities, faster adsorption kinetics, and are more resistant to abrasion. The original Russian RIP process was based on engineering expertise developed for uranium ore pro­cessing and has a few major drawbacks. The biggest problem is an 18-30 day resin stripping process, which results in a huge gold lock-up. The problem was recently overcome by the development of a new stripping technology which cuts the time to 12-24 hours. Currently, there is rather limited practical knowledge of the Russian RIP process in the West, but often Western mining com­panies developing gold mines in the fonner Soviet Union are hard pressed by their local joint venture partners to take a serious look into RIP. It is probably only a matter of time before one of these companies will cross Soviet technology with Western engineering and develop a modem RIP process as an attractive option to the current CIP and CIL technologies.

Jan 1, 1996

By J. Bartrum

Semi-autogenous, (SAG), milling operations can realize substantial Increases in mill throughput by removing and crushing critical size, slow grinding, material from the SAG mill. Full-scale plant testwork showed that modifying the Kidston SAG/ball circuit to a semi-autogenous-ball milling-crushing (SABC) circuit would increase plant throughput by 25 to 30%. The methods used to determine the value of the SABC circuit and the design of the circuit are discussed.

Jan 1, 1988

By A. Bhagwat, S. Tadolini

"Steel members of the ground support systems in underground mines are routinely exposed to corrosive environment that may range from acidic to alkaline. Corrosion of steel bolts leads to metal loss and thereby, reduction in strength and useful life. Protective coatings are commonly applied to the steel bolts to combat corrosion. However, coatings are expensive and often cumbersome in practical applications. Instead, Minova has developed an innovative technology based on sacrificial anodes. The anodes were designed from non-ferritic alloys that are inferior to steel on the Galvanic Series. This paper will present data from field testing to show significant benefit of the technology. Potential applications in current products will be discussed. INTRODUCTION Corrosion is a physical alteration of a steel material from electrochemical reaction with its environment that often results in reduction of the mechanical and physical properties of that material. Mine roof bolts, the subject of this investigation, are particularly susceptible to corrosion as they can be exposed in their working environment to ground water and air with high humidity. As other researchers have determined, corrosion increases markedly in sulfide ore bodies due to acid runoff. There are several types of corrosion that a rock bolt is likely to undergo when used for ground reinforcement in underground mines (Aziz et al., 2013). Of all the types of corrosion, pitting is particularly dangerous as it can remove capacity for the bolt to deform with subsequent strata movements. Sudden failure of a bolt is likely to occur when severe pitting corrosion is experienced. The type and nature of corrosion depend on the nature of the ground condition and bolt encapsulation. Generally, the type of corrosion and severity of the corrosion varies along the axis of bolt. Almost all of the mine roof bolts used in mines, with the exception of fiber reinforced polymers, are made from steel. The corrosion of iron is an electrochemical phenomenon with the overall equation:"

Jan 1, 2018

By Germán Toledo

The closure of TSF represents a critical milestone in the life cycle of mining operations, requiring the integration of technical, environmental, and social dimensions to ensure long-term safety and sustainability. The GISTM introduces the concept of “safe closure” as a demonstrable technical condition in which there are no ongoing material risks to people or the environment. This status must be validated by an independent technical reviewer and formally approved by the Accountable Executive. This article presents a risk-based methodology to support the achievement of safe closure, aligned with the principles and requirements of the GISTM. The proposed approach emphasizes the need to identify, assess, and manage closure and post-closure risks progressively throughout all phases of the TSF life cycle: from site selection and design, through construction and operation, to closure implementation and long-term monitoring. The methodology integrates key elements of effective risk management, including comprehensive knowledge bases, consideration of climate change, credible failure modes, continuous monitoring, stakeholder engagement, and governance. The ALARP principle is applied to demonstrate that residual risks have been reduced to tolerable levels. By incorporating closure planning from the earliest stages and adopting a risk-based view throughout the entire life cycle, this methodology aims to support mining organizations in achieving a verifiable and responsible closure of tailings facilities, in line with international best practices such as those of ANCOLD and ICOLD. The proposed framework offers a practical contribution to strengthening the credibility, effectiveness, and sustainability of tailings closure processes.

Feb 22, 2026

By Satid Therdkiattikul, Donald A. Dahlstrom

By oxidizing the pyrite matrix through biological leaching of precious metals ores or concentrates, better than 90% recovery of gold and silver is achieved. The paper develops three precipitation processes that eliminates arsenic and all other toxic elements in the resulting liquor after the biological reactors. In addition, the precipitates are highly crystalline and resist resolubilization. The latter must be tested for at least six months by EPA test procedures. The three systems are temperature (must be at least 120°C or higher) lime or limestone. A continuous pilot plant was employed for all three systems and complete recommendations are given to optimize Fe/As molar ratio, reaction kinetics (detention time) pH, temperature, wt % feed solids as well as resultant reagent consumption based upon continuous operation.

Jan 1, 1995

By Satid Therdkiattikul, Donald A. Dahlstrom

Many gold ores are known to be refractory so that conventional cyanide processing will result in serious losses of gold and silver values. A significant percentage of these refractory ores contain aresenopyrite and the gold and silver is usually encapsulated within this matrix as well as the pyrite matrix. Normally the values can be recovered as flotation concentrates because of the sulfide compounds with recoveries of over 90% and at very good grades. In order to free the gold and silver, the sulfide matrix must be destroyed. This can presently be achieved by (1) pressure­temperature leaching (2) roasting and (3) bacterial leaching. All of them have advantages and disadvantages as well as an obviously increased cost for the each processing method. However, the increased gold and silver recovery should and must more than offset this cost. It is believed that gold recovery should be well over 90% from the concentrate so that overall recovery from the ore should be in the 90-95% region. All three processes must consider pollution control of both sulfur and arsenic to prevent contamination of air, water or land through improper waste disposal. This paper will concern only bacterial leaching and its necessary control of effluents and solids. Sulfur does not appear to be a problem as the element is oxidized to sulfate and is precipitated with an acceptable solubility. Other important improvements that must be controlled are arsenic and iron which are present as significant values (1-12 g/1 of arsenic, 20-40 g/1 of iron). In addition much smaller values of base metals, aluminum and magnesium can be present as well as other elements depending on the ore and these must be low enough after treatment to meet EPA regulations.

Jan 1, 1993

By Robert L. Cascio

The mining industry uses a large amount of electric power. Their equipment is subject to extreme environmental conditions and mechanical shock. A significant number of electrical accidents are a result of improperly grounded electrical equipment. Federal regulations require the safety ground bed resistance to be measured once a year or after modifications. Most commercially available instruments used to measure the ground bed resistance require the ground conductor to be disconnected and the power system disconnected for safety reasons. The "fall of potential1' method requires auxiliary ground rods and approximately two hours to complete the test. Although a new instrument was initially thought to measure the ground bed resistance immediately without isolating the ground bed, field tests have shown this method is not accurate. In some cases, a continuous measurement of the ground resistance is desired. A monitor has been developed and is presently being evaluated at several mines. These installations will be discussed.

Jan 1, 1992

By W. Burger

In underground mines worldwide, a large number of short and small diameter slot holes need to be excavated. Herrenknecht has developed and built a new boxholeboring machine based on the well-proven Microtunnellingpipe jacking technology. The innovative Boxhole Boring Machine significantly increases work safety and requires only minimal drift dimensions. The high and consistent production rates that can be achieved result in enormous time savings compared to conventional drill and blast excavations. GENERAL ASPECTS In gold, copper and ore mines ventilation shafts are required to prepare block caving operations, to discharge ore onto the transportation level and to provide evacuation shafts. A high level of occupational safety and efficiency is the main objective when drilling vertical or inclined shafts. The faster and more safely shafts can be constructed, the earlier the actual production in the mine can start or be continued. Mechanized or conventional methods (drill&blast) that have been used to date only partially meet the required safety standards and fail to provide the requested production rates.

Jan 1, 2012

By R. D. Peterson

As underground mine operations expand, the ventilation systems supporting them become complex. Complexity increases with periodic ventilation changes. New diagonal connections require a rebalance of resistance to maintain airflow in affected splits in the system. Incidents of mine fires and explosions have occurred in U.S. coal mines when diagonal connections resulting from ventilation changes have resulted in changing airflow directions. MSHA regulations prohibit the reversal of airflow and poor ventilation practice in general, but regulations cannot stipulate or recommend proactive preventative measures because every situation is different. This paper discusses the phenomenon of diagonal branches and recommends practical precautionary measures that can be taken to prevent airflow reversal in planned ventilation changes.

Jan 1, 2012

By J. Pereyra, M. DeMarco

"INTRODUCTION It can be vital that bolted joints holding subassemblies together remain secure. Bolts should resist the loosening effects of vibrations and dynamic loads yet need to be easily removable during maintenance. When a threaded fastener is subjected to vibration, the rapid movement causes a lowering of friction against the threads and a subsequent loss of preload. The loss of preload allows the fastener to vibrate loose and possibly fall out. As the diameter of fasteners increase desired preload becomes increasingly more difficult to achieve. Input torque requirements for achieving proper bolt preload is exponentially related to any given fasteners diameter. This means that specialized tooling or bolting practices are usually required to attempt the tightening of fasteners to reach their required preload. Traditional methods can cause problems with joint integrity and do not provide consistent bolt load across the bolted surface. BOLTED CONNECTIONS A failed critical bolted joint can lead to high maintenance costs, machine downtime, and risk to worker safety. Control of the clamp load in a bolted joint is vital. However, when faced with a problem joint, it is not surprising that the design engineer will not have an answer if asked about the clamp load. Torque calculations must always be based on the existing conditions that often are vague. Unless all parameters are correct, the calculation will be unreliable. Examples of parameters are: • Thread condition of the fasteners • Hardness of contact surface • Material (steel, aluminium, copper, etc.) • Extra friction from a locking fastener • Extra friction from an adhesive • Lubricant on the thread • Type of bolt head (flanged, regular or serrated) • Surface coating of the bolt • New or reused fastener During tightening, bolts are subjected to both tensile and torsional stress. The total stress in a bolt can be calculated using the formula: Total stress = vsx2 + 3txy2 In order to maximize the desired tensile stress (sx) it is vital to minimize the torsional stress (txy). Tensile stress (clamp load) is achieved when the bolt is axially elongated. Unwanted torsional stress (twisting) in bolts arises during tightening due to thread friction. High thread friction increases torsional stress and causes yielding at lower clamp load levels than normal. A lubricant is necessary to minimize the malign torsional stress. However, many commonly used bolt-locking systems are based on increased thread friction (deformed nuts, adhesives, etc). To minimize thread friction and concurrently safely secure the joint has often incorrectly been considered impossible. The use of locking systems that increase thread friction is the single most common reason why the full capacity of bolted joints is not utilized. The following example illustrates the problem."

Jan 1, 2015

By J. Litsenberger, T. E. Marshall, L. Burke, R. Melville, A. T. Iannacchione

Excessive levels of horizontal stresses cause ground fall hazards in underground mines in the Appalachian Basin. At an underground stone mine in Pennsylvania, a modified stress control mine layout is reducing the hazardous conditions associated with excessive horizontal stresses. A microseismic monitoring system is in place to measure levels of rock stability and provide information on the effectiveness of the design technique. The microseismic data is supplemented with frequent and extensive mapping of roof falls and roof rock damage. Findings to date show that the stress control layout provides more stable conditions and thus a safer environment for the mine workers.

Jan 1, 2001

By R. Perlo

"INTRODUCTION Peoples’ and operators’ safety in construction are tightly linked to the engineering choices, as much as the necessity of reducing time and costs of realization. Therefore, it is of paramount importance to address them properly from the earliest stage of the design, identifying the risks connected to the work and the variability of such during the different phases of the project. Risk is often measured as the expected value of an undesirable outcome. Regarding to occupational safety and health, the risk is the likelihood that a person may be harmed of suffers adverse health effects if exposed to a hazard. This combines the probabilities of various possible events and the assessment of the corresponding harm into a single value. However, the actual occurrences are often more complex than a single binary possibility case. In a real case scenario, with several possible accidents, the total risk is the sum of the risks for each different accident, provided that the outcomes are comparable. The semi-automatic tunnel support system along with its erector machine proved to be a solution with improved structural performance, able to reduce the time and yet to deliver an enhanced, quality-aware and safer working environment for the operators. The implementation of the system provides the engineers, the contractors and the owners with an effective alternative option shortlisted in 2015 for the ITA Award for the Safety Innovation of the Year. In a market industry driven by safety and time constrains the efficiency shall be the ultimate goal, in order to provide solutions able to negotiate with the most challenging ground conditions. In this paper, the authors describe the recent developments on regard of this whole new tunnel support system, including design approach and presenting related case histories OFFSETTING THE RISKS Considering the above factors, from the manufacturers’ point of view, an effective way to limit the construction risks is to focus on the material and technological characteristics, their application and the risks related to them including any residual risks. Finally addressing the construction needs also involves time and cost-effective solutions. The path to follow is an integrated approach where the efficient management of the risk is supported by a flexible, user-friendly, and time effective product that is able to provide a safe, reliable and viable solution to address the construction requirements. Therefore, in a market sector driven by safety and time constraints, the efficiency is a key goal, in order to avoid redundancy and yet to deliver a safe working environment able to meet the construction schedule. The safety of all the parties involved is given by stable working conditions, either for the workers, or the operators and eventually the public. Therefore, the solutions provided should ‘strengthen’ the overall condition and such “to limit or to reduce the deformations within acceptable designed limits and to prevent [the tunnel] to collapse” [1: Clause 207.1.4]."

Jan 1, 2018