Search Documents

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

By Michael Laing

"Geology plays a critical role in many aspects of blasting, from fragmentation to wall control. One often overlooked component of blasting concerns blast results due to the effect of geologic features. The direction of blasting, with respect to strike and dip, can produce varied results, depending on thescenario. Working with geological features, as opposed to against them or without regard to them, can therefore dramatically improve blasting results. This paper focuses on the role of “geologic features”, which include joint-sets, natural fractures, and bedding planes (all of which are commonly referred to as “seams”) for the purposes of this paper. The goal of this paper is to promote understanding and mitigation techniques for various scenarios in which there are identifiable geologic features. Depending on the nature of these features (strike and dip specifically), blast design and pit advancement/development can be carefully considered to use make the best use of these features and optimize blast results."

Jan 1, 2016

By John Eloranta

This paper is a case study showing the assembly of available rock property parameters for the purpose of blast design. Blast optimization now includes subsequent milling and requires a full knowledge of the rock mass. Individual blast holes should be designed using all available data. The parameters include: geologic layer from diamond drilling, shovel performance, crushing plant experience from that area, drill monitoring, magnetic susceptibility from a downhole probe, size analysis history from digital image analysis, compressive strength tests of problem areas and cross hole sonic testing. Bedding thickness observed from drill core appear to have a strong influence on fragmentation.

Jan 1, 1996

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By Dennis R. Jr Bell

Before beginning any site development or mineral extraction activity, it has been well documented that it is first prudent to gain an understanding of the prevailing geologic conditions.Whether it’s identifying the depth to type of bedrock, or determining the quality and quantity of the in place mineral deposit, these factors should always be considered in a project’s fatal flaw analysis. In situations where there is limited subsurface information, geologic models have been proven to be one of the most valuable and cost-effective tools used by the developer and/or his consultant.

Jan 1, 1997

By W C. Burkle

A rather common observation over the last several decades at least has been that rock or ore properties influence blasting results more than does the explosive type that has been used in the blast. It we accept that premise than it is held here that the material to be blasted should receive even closer attention as to its properties. Several years ago, Dr. Richard Ash published papers that pointed out the rock properties that mostly influence blasting. These principles are given attention in this paper. We have gone somewhat further - or lets say expanded this subject in regard to the role of rock structure in open pit blasting. Though open pit work is given some prominence, we believe that much can be observed and applied to underground mining.

Jan 1, 1979

By J. D. Aubertin

Rock blasting is a complex engineering process that requires in-depth knowledge of operations and geomechanical conditions. Acknowledged design precepts are based on cratering behavior associated with stiff hard rock masses. Other cratering mechanisms may however arise under certain geomechanical conditions such as extremely fractured rock masses, or with soft rocks such as rock salt and potash. The burden dimension also plays an important role in the prevalent cratering mechanisms of a given blasting condition. The present article investigates the variability of cratering profiles and geometrical trends based on characteristic geomechanical differentiation and considering the influence of burden. The differences in observable mechanisms are examined through small and large-scale single hole blast (SHB) tests. SHB tests involve a series of individual shots blasted parallel or sub-parallel to an open face. The burden dimension is varied to obtain burden dependent characteristic trends. The breakout shape is represented by a crater model in the form of a power law equation capable of describing prismatic, concave and convex cratering. The formulation comprises two reference index parameters that can describe the geometrical and geomechanical conditions. SHB test campaigns conducted in rock salt, limestone, massive amphibolite, pinolite, and grout blocks are compiled in quantitative manner to demonstrate the influence of geomechanics on cratering profiles. The observed trends are corroborated through numerical modelling carried on Finite Element Model (FEM) LS Dyna to investigate the prevalence of specific cratering mechanisms. A series of SHB tests at large and small burden values are also used to showcase the influence of geometry on the prevalent cratering mechanism and the resulting crater

Jan 1, 2024

By Ivan Kovac, Pero Marjanovic, Branko Bozic

"The paper deals with results of geophysical survey of the rock masses, and the blasting parameterswhich have effect on the fragmentation in quarries . A relationship between the burden, which is the distance between the charged borehole and the free rock surface, and the velocity of longitudinal waves in the rock mass is established based on measured values for different quarries. It is shown that the drilling geometry can also be detemrined from this relationship."

Jan 1, 1999

By John Montgomery

This paper discusses the major changes to the Commissioners Rules and Regulations, Chapter 120-3-10 “Rules and Regulations for Explosives and Blasting Agents”; how the changes came about, and a summary of the status of the blasting industry in Georgia.

Jan 1, 2003

By Stephen Mansfield

In open-pit mining operations, the drill and blast processes have a significant impact on the downstream operational performance of crushing and grinding of ores and recovery of metal. The blast pattern parameters, combined with the material properties, defines the run of mine fragmentation, which in turn drives the subsequent energy requirements for further processing and mill throughput. A common parameter used to describe a single hole or collection of holes is powder factor, the ratio of explosives to the quantity of material blasted. One often-neglected aspect of calculating powder factor is the explosives contained within the length of hole drilled into the top of the bench from the previous bench, known as subdrill. Explosives in the subdrill directly affect the bench below and thus do not contribute significantly to the results of the upper bench, even though they are traditionally included in the powder factor calculation. This paper presents geospatial data modelling methods that link individual holes from an upper bench to the bench below. This enables a new method for the calculation of powder factor, whereby the explosives in the subdrill from the bench above are included in the powder factor calculation of the bench below. This method allows for a clearer understanding of the impact of subdrill on fragmentation, and how variations in blast designs in the upper bench, i.e. hole diameter, burden, spacing, subdrill length, explosive type, primer position, etc., and accuracy of implementation, i.e. actual hole depths and explosive mass per hole, affect the powder factor and blasting results in lower benches.

Feb 6, 2023

By Roger S. Jackson

"This study interprets vibrations produced by single underground shots, recorded on surface by 135 digital seismographs laid out in four linear arrays. Several vibration anomalies were observed and are investigated. A novel method of displaying the blast-induced vibration iso-contour data relative to the three-dimensional representations of the geological rock units and structures leads to the following interpretations:• The identified faults commonly dampen or amplify vibrations, on the evidence of the peak particle velocity,• Strong anisotropy of geologic formations produces different vibration attenuation in the various directions of interest,• Low-vibration “depressions” can be related to the presence of faults, and• Higher vibration levels than expected based on ‘scaled-distance’ principles are observed close to intersecting faults.The interpretations from this study document a better understanding of the geotechnical influences on blast induced stress wave propagation in a geologically complex area. The practical benefit of this understanding is better control of surface vibrations, experienced from underground mining activities."

Jan 1, 2010

By Tyler Acorn

In December of 2009 an estimated one million ton slope failure activated a 10 million ton mass impacting use of the main ramp system in the Newmont Gold Quarry pit. The failure left behind a 400 foot (122 meters), vertical to sub vertical scarp feature and shut down production in the lower benches of the pit.

Jan 1, 2011

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002

By TTE-Europe GmbH

A few years ago, the term Track & Trace for explosives was only known in Europe and Brazil at most; the introduction of this technology is experiencing an undreamt-of boom worldwide. More and more countries are enacting legislation to introduce Track & Trace of explosives and follow Europe and Brazil on this path. At present, the world's leading manufacturers are already using such solutions, are in the process of implementing them, or are in the planning process. However, based on the experience gained in Europe, there are outstanding challenges for all manufacturers. These are questions of compliance, logistics, distribution, and, of course, especially, the necessary adaptation of the production environment. However, this development involves considerable effort on the part of the manufacturers. New devices for marking the explosives and digitally recording the data are integrated into the production process. This should be done as cost-effectively as possible, without restricting production capacity and speed, and with as few process changes as possible. This paper uses real-life customer experiences examples to explain paths from project design to real implementation. Lessons learned from the experience of European explosives manufacturers are presented, missteps are described, and solutions are identified. Individual steps along this path are explained, and solutions are told to avoid pitfalls and bottlenecks. Finally, it refers to the risk analysis and concrete examples in implementing the planning into production. Methods of marking various explosives are shown, and the use of Track & Trace to solve logistics tasks in picking and shipping explosives, including the data exchange with ERP (Enterprise Resource Planning) systems.

Jan 26, 2026

By Richard L. Ash

A question that frequently arises during litigation concerned with accidents or alleged damages involving blasting is "were the explosives used according to the best known standards"" The question is not confined to only law suits, however, but also everytime poor blasting results occur. Unfortunately, general guidelines that can be used to define what may be considered as proper practice have not been established by any responsible body upon which to base a reliable Judgment; more often than not decisions are made primarily according to personal opinion.

Jan 1, 1975

By Adam T. Young

This paper will describe the process of using low density bulk emulsion as a means to maximize the production of an oversize or “rip rap” aggregate size range (8 inch to 72 inch) that the quarry customer has a market demand for. It will also discuss the pre-blast and post-blast metrics used during the product trials and evaluation.

Jan 1, 2017

By Mauro Fornaro, Marilena Cardu, Renato Mancini

Detonating cord cutting is widespread in dimension stone extraction, especially in the case of hard, abrasive stones as granites, an important resource for Italian industry. General data on this production sector are briefly discussed and analyzed in the first part of the paper. The theoretical basis of operation are summarized, and compared to data obtained from selected commercial cases, in the second part.

Jan 1, 1994

By David Weidner

Public relations, regulatory compliance, determination and implementation of pre-blast inspections, and accurate blast monitoring data are all essential components when conducting blasting operations for a large scale, high profile, urban site development. By working closely with the contractor, an independent vibration consulting firm can provide the commitment of time, energy and resources to tie all of these elements together. When this comprehensive approach is properly implemented, problems often associated with projects of this magnitude can be almost completely eliminated.

Jan 1, 2001

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By Malcolm Scoble

The estimation of digging, ripping and blasting requirements in advance of mine production is a difficult task. The characteristics of the superficials and rock mass govern the type and intensity of ground preparation required as a prelude to loading. The incentives for optimum planning of preparation are primarily economic but also relate to mining method and equipment selection, productivity and environmental impact.

Jan 1, 1985