Search Documents

By Hung Tran, Denis Fleury, (Ken) Qian Liu

Pastefill technology has gained an increasing popularity over the past decade. The main advantages are: environmental performance (mainly in tailings disposal), low operation costs and ease of operation, as well as homogeneous properties. However, its weaker nature compared to other types of fill makes it more vulnerable to blast damage. In the last few years, Louvicourt Mine has experienced some cases of pastefill sloughage during the mining of secondary stopes. In order to reduce pastefill sloughage, some studies have been undertaken to investigate the causes and to find possible solutions by looking at stope design, extraction sequence, ground support and blast design. This paper presents the results of a blast damage study carried out at Louvicourt on the 860m level. The instrumentation included vibration monitors (using 6 sets of triaxial geophones grouted in the pastefill), a borehole camera to observe the damage in the pastefill, and a cavity monitoring system for three-dimensional surveys of the blasted stope. The test stope was mined out by four slot blasts and three mass blasts. Most of the damage was created by the mass blasts. It was found that the accumulation of ground vibration was mainly due to the low seismic velocities in the pastefill and the relatively tight delay between blastholes. In addition, there was a substantial difference between the critical PPV in the confined and unconfined pastefill. In practice, these findings have led to modifications of blast design to minimise the exposure time of pastefill walls to air. Such modifications included changes of blast sequence in secondary stopes and delay layout between heavily loaded blastholes. Over the paste two years, the implementation of new blast sequence has shown encouraging results in terms of reduced pastefill sloughage and dilution.

Jan 1, 2000

By H. Bilgin, Sedat Esen

In this paper, the ground vibrations induced by blasting for stripping work at Sekkoy Open Cast Coal Mine belonging to TKI Yenikoy Lignite Mine (YLI) are investigated and the procedures for monitoring and control of ground vibrations are presented. Ground vibration measurements are conducted in the direction of Turkish Electricity Authorities’ Yenikoy Establishment and social facilities because of the complaints and annoyance arising from this site. Forty ground vibration records are taken in this direction and the vibrations are measured in transverse, vertical, longitudinal components together with peak vector sum. After then the scaled distance relationship is determined at 95% confidence value. Further, Fast Fourier Transform analyses are carried out to determine dominant frequencies for both ground and the structures and amplification factors. When the records taken at four different structures together with the ground are evaluated, it is observed that one of the apartment buildings is amplified the amplitude of longitudinal component 4.3 times. The maximum allowable amount of explosive that can be fired safely at this mine is calculated and recommended on. In the determination of safe amount, 95% confidence line, USBM RI8507 and OSMRE criteria, the dominant frequencies of both ground and the structure, amplification factor and the human response are taken into account.

Jan 1, 2001

By F. Schott, M. James, G. May, E. Baker, C. Johnson, R. Bauer

Explosive demolition typically utilizes cutting charges to sever columns, detonating cord to time charges and provide an initiation path, and dynamite as a kicker charge. The kicker charges of dynamite are used to “move” columns out of alignment, causing collapse. Demolition projects involving dynamite can pose significant health and safety risks to workers and the public. Nitroglycerin in dynamite can cause dizziness, fainting, and other health problems. Moreover, dynamite placed directly on columns can result in fragmentation and cutoffs, preventing other charges from being initiated and resulting in incomplete demolition. Fragmentation can occur from columns and travel significant distances from the initiation point, sometimes reaching hundreds of meters away. This fragmentation can pose serious dangers to anyone in the vicinity, including workers and members of the public, as the debris can cause severe injuries and property damage. The force and velocity of the fragmented material can be unpredictable and difficult to control, making it important to take proper safety precautions and consider alternative demolition methods that minimize the risk of fragmentation. Previous work concluded that casing charges in water showed that a reduced dynamite charge mass could still successfully kick the charge out of alignment. This study aims to investigate the use of Pentolite boosters in water-cased charges as a safer alternative to dynamite-based demolition. The research involved testing various amounts of dynamite and pentolite boosters in water to compare their effectiveness in moving a hanging W-beam, which swung freely like a ballistic pendulum. Water-cased charges consistently move the column at a higher velocity than the traditional dynamite charge placed directly on the column. The method of water-casing increased the area of impact and impulse felt by the column, improving demolition efficiency when compared to traditional demolition methods as found in previous studies. Pentolite water-cased charges moved the column at 7.8 meters/second (m/s) while the dynamite water charge moved the column at 5.9 m/s. The increased strength and explosive properties of the pentolite contributed to this increase in velocity. This study showed that it is feasible to remove dynamite from demolition projects by utilizing pentolite boosters and that when considering safety, explosive properties, and effectiveness, pentolite boosters can be cost effective as well.

Jan 1, 2024

By Jair Koppe

The unsatisfactory blasting effect is mainly related to the improper selection of design parameters of drilling and blasting scheme. In order to evaluate the rationality of drilling and blasting scheme, scientifically, this paper brings forward a method for scientific evaluation of blasting scheme. This method evaluates the blasting scheme by observing the accuracy of drilling, explosive density, charge, lumpiness analysis, filling length, slope surface design, floor level, vibration monitoring and flyrock. The evaluation involves different stages of blasting construction and implementation, such as terrain survey, drilling, charging, environmental impact and safety evaluation. Through this method, several key problems for improving blasting scheme design can be determined by analyzing each parameter. This method improves the key parameters of blasting design by analyzing blasting results and establishes the relationship between blasting effect and technical design.

Feb 6, 2023

By J Silva Castro, W C. Wedding, B T. Lusk, J Calnan, E G. Morris

The emergence of electronic detonators for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. This paper reports on an independent study quantifying the accuracy of two electronic and two non-electric systems in which 674 detonators were tested. This research aimed to determine the accuracy of commercially available electronic detonators as compared to non-electric shocktube systems. Each system was tested over the viable ranges of delays available. Statistical models were then applied to quantify the scatter present in each system. Suggestions for the use of electronic detonators are made from the findings of this work. This work was made possible through funding from the United States Department of the Interior Office of Surface Mining Reclamation and Enforcement.

Jan 1, 2012

By Ali Kahriman

This paper presents the results of ground vibration and air blast measurements from tunnel blasting activities during the construction of the Beylerbeyi-Kucuksu waste water tunnel under a residential area in Istanbul, Turkey. Within the scope of the study, the blasting pattern of the tunnel was engineered using Tunnel2000 design software and field studies and measurements for evaluating the productivity and safety of shots were realized for 136 rounds. During the study, the advance of the tunnel, face condition, ground vibration, air blast and neighbours’ complains and comments after every round were observed and the tunnel pattern was improved. Finally, an empirical relation for this tunnel route was developed between scaled distance and maximum amount of explosives, to continue activities in a safe and productive manner.

Jan 1, 2006

By Ali Kahriman, Abdulkadir Karadogan, Deniz Adiquzel, Umit Ozer, Suat Bicer, Mehmet Aksoy

This paper presents the analysis and measurements of blast-induced ground vibrations during the construction of Istanbul Kagithane – Piyalepasa – Dolapdere – Dolmabahçe highway tunnels. These tunnels known as T1 and T2 are being constructed by a joint venture group. Within the scope of the study, the particle velocities and frequencies associated with 126 shots during the advancement of the tunnels were monitored and analyzed by vibration monitors at the test site. During the statistical analysis, three different predictor equations widely used in the literature were used to predict peak particle velocity (PPV) and the results and comparison of the predictor equations are presented in this paper. Finally, the particle velocities and frequency values of all blast events were evaluated according to USBM and German DIN 4150 Norms in order to determine the damage risks of the neighboring buildings and structures.

Jan 1, 2008

By Russell Carter, Tom Barkley

"Optimization of blasting is hampered by the lack of inexpensive methods of measuringblast results. Optical methods of size analysis have the potential of creating abreakthrough in size analysis and in overall blast optimization. Attainment of reliablemeasurements hinge on solving a number of shortcomings inherent to optical systems."

Jan 1, 1999

By RR Vandebeek, A W. Bauer

The Canadian Explosives Research Laboratory regularly evaluates the properties of commercial explosives for authorization under the Canada Explosives Act. Propagation sensitivity is normally measured using small scale tests. Relating the results in actual mining practice is difficult. In the mining industry, the propagation sensitivity is a measure of the ability of one cartridge to propagate to an adjacent cartridge in a borehole. They may be separated by a gap of in-filling material. As well the propagation sensitivity will be affected by the explosive type, temperature, degree of coupling, cartridge diameter and other factors.

Jan 1, 1987

By Koichi Kurokawa, Takeo Ueda, Masahi Nakano, Yoji Tasaki

A lightning strike generates several 10kA and several billion volts, and earth currents generated by lightning is dangerous to some underground and all surface blasting operations. In order to evaluate the safety against lightning in conventional electric firing method and electromagnetic induction blasting system, a test is conducted by connecting a wire with an impulse generator. Frequency of impulse current used in the test is 17kHz and the waveform is a vibration type and the duration time is 250 ~usec. The results of the test show that induced current increases with the increasing of impulse current. In the case of MBS connection, when maximum primary current is 1700A, Maximum secondary current is 11.8A and the electric detonator is fired at this condition.

Jan 1, 1988

By Zhang Shixun, Wang Xuguang, Wang Guoli

A massive millisecond blast at an open-pit mine of large scale can be realized by using the blasting technology of pre-loaded explosives, which can enlarge production scale, reduce the frequency of blasting and of large production equipment movement, and raise the production efficiency. The reason why application of this technology is restricted at high sulfide ore deposits of variable and complex geological conditions is that an exothermic reaction will take place when explosives contact sulfide ores, which could lead to accidents such as spontaneous burning and detonation of explosives pre-loaded in boreholes, influencing blasting and production safety. The thermal decomposition reactions of emulsion explosives of different prescriptions in contact with pyrite have been studied by differential thermal analysis (DTA), kinetics parameters calculation and accelerating rate calorimetry (ARC), and on the basis of the above studies, the safety of emulsion explosives used in sulfide mines has been evaluated with the safe contact time of different emulsion explosives with pyrite determined.

Jan 1, 1998

By D Wilson, E Nagy, R A. Augsten, R R. Vandebeek, R L. Guilbeault

The Canadian Explosives Research Laboratory (CERL), is evaluating the status of the Schedule IV explosives container as it presently pertains to the industry. The Schedule IV container serves the same purpose in Canada as the IME 22 container does in the United States. That is, to transport detonators on the same vehicle which is carrying explosives.

Jan 1, 1990

By Courtney Vallejo, Rafiqul Tarefder

This study examines the effects of small scale airblast experiments on cohesive soils and the resulting ground vibrations and crater geometries. Relationships for ground vibration attenuation with soil depth and distance from the blast source were developed. The study is part of a broader research topic of understanding the vulnerability of earthen embankment dams to blast loading. Many earthen embankment dams in the United States were constructed more than fifty years ago and were not designed to withstand high-stress loading such as blast loading. These structures may be susceptible to failure and it is important to describe the response of the earthen dam during a blast event.

Jan 1, 2013

By Harsh Kumar Verma

Blasting off-the-solid is the most commonly used method during development of galleries in Bord and Pillar method of underground coal mining. In this method, only P5 explosives are used with permitted delay detonators in accordance with the safety requirements stipulated by the regulatory bodies. Delay detonators made with pyrotechnic delay compositions have inherent scattering in their delay timings. It is desirable to use precise detonators to achieve better fragmentation, less vibration and noise. Overlapping of delay period is undesirable from production as well as safety point of view.

Jan 1, 2008

By Salah A. Taqieddin

In an open pit, or a quarry blasting operation, a muck pile of broken material of given size and quantities suitable to a load/hauling system is normally created at the foot of a bench. Fragmentation can be used to evaluate the efficiency of that blast configuration.

Jan 1, 1987

By Roger Favreau, Patrice Favreau

The article reviews the aspects which contribute to the quality of the results from a blast with explosives, namely a good floor, no large blocks, easy mucking, and explains the mechanisms of the blasting process which decide on the quality of these aspects for a given blast method, and how these mechanisms can be simulated from basic principles. It proposes that good fragmentation size distribution can also be important if the rock is going to a crusher, e. g. for the ore in a mine and for the rock excavated in a quarry.

Jan 1, 2012

By Kush Patel, Gary Cavanough

Mining operations consume over 2.5 Billion Australian dollars’ worth of bulk explosives annually (Richardson, 2018). Despite the large volume of product used, current practices only conduct a cup density test of the product being used. Explosive products are made up of a number of components, each with an effect on the performance of the explosive. This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser. Through a total of 60 tests carried out on 10 different bulk explosive products the average error of each method was determined, the BEA presented an average error of 0.11%, whereas, the wet chemistry method presented an average error of 1.90%. This is a significant difference when considering the importance of formulation of explosives. Further investigation into the capabilities of the BEA are also presented in this paper.

By Kush Patel

This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser.

Feb 1, 2020

By R R. Singh, U K. Dey, S K. Roy

"Commercial explosives being a heterogeneous mixture of many chemical compounds in prefixed proportion, their velocity of detonation (VOD) may vary from batch to batch, due to variations in the proportion of the chemical composition and process parameters even within their tolerance limits. Inherent limitations of measuring methods and human variations during measurement also add to the variation in VOD values determined practically. Therefore, it is customary to define a range of VOD values rather than a fixed value of VOD for a particular explosive.Variations in VOD values of four commercial permitted explosives in India were evaluated under open unconfined condition using Dautriche method and a resistance wire method based continuous VOD meter. Comparative evaluation of VOD values of selected explosives were aimed to check the relative effectiveness of continuous VOD measurement of small diameter cartridged permitted explosives using cheaper co-axial wire instead of recommended costly VOD rods along with the continuous VOD meter. Results of evaluation revealed that continuous VOD of commercial small diameter cartridged explosives could be determined using cheaper co-axial resistance cable with comparatively better accuracy than the most commonly used Dautriche method."

Jan 1, 2007

By Philip M. E Thomas

For over sixty years man has struggled to defeat the natural swamp lands known as the Florida Everglades as demand for land to support the burgeoning population growth in the state continued almost unchecked. Over the past ten years there has been a growing awareness that this land development could wipe out a whole ecosystem in a very short time unless steps were taken to reverse the trends. In 1991, a state law called the Marjory Stoneman Douglas Everglades Protection Act was enacted giving power to the South Florida Water Management Board to condemn certain lands for conversion to manmade swamp lands, designed to filter polluting run-off water from the agricultural lands around Lake Ockeechobee.

Jan 1, 1994