Search Documents

By Michael K. Phang, Thomas A. Simpson

Field studies at an underground mine site were conducted to evaluate and monitor blast-induced vibrations on an underground coal mine roof. The vibration data were evaluated so that a suitable damage criteria or guidelines from which a safe operating distance between surface blasting and underground mine operations can be established.

Jan 1, 1984

By W. J. Birch, L. Bermingham

Air overpressure is becoming an increasingly problematic issue within the quarrying industry. With blasting operations moving ever closer to residential properties, the number of complaints about air overpressure is beginning to increase. It is therefore important for operators not only to have a greater understanding of the blasting parameters that give rise to air overpressure but also the factors which have an effect on air overpressure levels as it attenuates with increasing distance from the location of the blast.

Jan 1, 2013

By Jorge Cárdenas, Gustavo Huerta, Regina Rocha Oriundo, Miguel Angel Humpire, Johan Salas Flores

Currently a critical activity for slopes stability and safety in mining is pre-split blasting to reduce damage from trim blast. Most common explosive used are based on packaged explosives, with 1 ½ in diameter cartridges initiated by detonating cord. Traditional loading process requires a significant amount of trained personnel, which in our application context could take up to 20 blasters. When pre-split blast is scheduled, it usually reduces the availability of the blasters on the total loading services at site which are also demanded to have production blasting ready at same 12-hour shift daylight time.

Feb 6, 2023

By Javier Illanes Pizarro, Gustavo Huerta Valer, Jorge Cárdenas Miranda

Bench stability is the basis of sustainability in an open pit mining operation. Taking care of the pit walls while maintaining fragmentation results can prove a challenge. In this study, technical proposals have been developed for extra hard rock mass (UCS>175MPa) with presence of unfavorable structural planes in high copper grade zones. The base case shows low compliance of fragmentation results and a significant loss in berm width, with over size boulders causing low primary crushing rates. Paradigms in current drill and blast design were overcome to improve fragmentation results and achieve objectives.

Feb 6, 2023

By David F. Street

In order to achieve an efficient operation in an open pit mine it is very important to develop and maintain good coordination and communication between various departments within the operation. This paper will address this subject using methods and procedures developed at an open pit gold mine in northern Nevada.

Jan 1, 1994

By Elias Poulakidas, Marco Arellano

The impact of a higher copper price on the open pit metal mining sector has derived in a faster and safer way in which the mining operation of broken and mineralised material is carried out. In this regard, a good control of bench stability allows a lesser extra removal of material and so more safety to get the planned ore. The stability is ensured through an efficient drilling and blasting, applying the current technology and available know-how. An efficient use of energy through low-density explosives which are the most adequate for the existing solid rock releasing energy in a smoother way through a deterministic detonation sequence which is the application experience presented here. This application experience has two main technological factors; the adequate type of explosive for the kind of rock, in terms of velocity of propagation (Vp) together with the use of a determined detonation sequence and the appropriate designs, which allow to reduce the level of damage to the walls and to maintain a minor backbreaking through quantification with vibration modelling carried out at the near field. The reductions achieved were 30% lower in peak particle velocity.

Jan 1, 2008

By Vaughn Bowns, Allen Stanley, Brian Redeker

"Running casing in drilling operations is often complicated by boulders or large cobbles.Past practices of dealing with these have included use of drop hammers, attempts to drillthrough or around the boulder, contact explosive charges and even pulling the casing andrepositioning the hole. All these methods are time consuming, expensive and offer noguarantee of success. In this paper a different method of dealing with these boulders ispresented that promises to be faster and less expensive with a much higher success rate.This involves using a light plastic conduit pipe to place a shaped explosive against theboulder. It requires no special tools or techniques not commonly in use in the drilling andblasting industry."

Jan 1, 1993

By Fred C. Drury

Blasting vibrations have been a concern to those using explosives since as early as 1927. Many criteria have been used to correlate vibration levels with damage to structures. After considering many alternatives, peak particle velocity has become the most commonly used criteria.

Jan 1, 1975

By Richard N. Snyder

In this system for connecting blasting caps to the initiation source, the need for a redundant design structure provides more reliable method of explosive initiation. This is accomplished by using a complete system starting at the blasting control, through the initiation line structure through the initiation line and connecting blocks to the blasting cap. The connecting structure between the initiation device and the blasting caps may be connecting blocks or other means.

Jan 1, 1995

By Deane Boddorff

A 440 Volt AC power line is a typical power source for energizing electric blasting cap circuits in driving hard rock tunnels. A common misconception exists that the caps actually see 440 Volts. This paper describes an analysis of the entire blasting circuit determining the current flowing and the voltage drops through each component. If, from such an analysis, one determines that the current to the caps is too low or too high, the components that require changing are easily recognized.

Jan 1, 1975

By Koichi Kurokawa, Takeo Ueda, Yoji Tasaki, Masashi Nakano

We have developed a new firing system which simplifies the handling and extensively increases the safety in electric blasting operations. Based on the principle of the transformer, this system is operated as follows: When a high frequency alternating current pulse (70-110 kHz) is applied to the lead wire and connecting wire (primary circuit), magnetic flux is generated in the transcore, and an induced current flows through the looped leg wire of the detonator (secondary circuit). Then the detonators are ignited by the induced current.

Jan 1, 1986

By Noel Dent

Increasing interest is being expressed in the development and availability of Electronic Delay Detonators throughout the world. Particularly in open-cast mining, the benefits associated with precise, reliable initiation systems are perceived to be considerable. Many of the systems currently being developed have sophisticated programming requirements associated with them, or are numbered systems that require predetermined layouts to determine timing patterns, and importantly are far more expensive than existing initiation systems.

Jan 1, 1994

By David G. Paton

"Electromagnetic surveys were conducted at the BXL Bulk Explosives Limited Mixing Plant andsurrounding area to characterize runoff from the site and possible impacts of salinity. The BXL Plant is located at the edge of a depressional area and any escape of soluble ions, such as nitrates, would have ended up in the slough to the west of the plant. Two electromagnetic (EM) instruments were used in the survey. A Geonics EM 3 1 was used in October 1997 and in June 1998, a new multifrequency instrument, a GSSI GEM 300 was also tested. Both instruments were individually mounted on a plastic sled with Teflon runners and towed with an ATV quad. Position was determined using a Trimble Pro XL global positioning system (GPS) with a real time correction mode Landstar receiver for an accuracy of about *l m. Both GPS and EM instruments were set to collect data at 1 second intervals. The quadrature maps for both instruments showed essentially the same information, namely of very high conductivity, appearing to emanate from the mixing plant. The levels of conductivity were highest where the saline water appeared to pool, at the southern end of the slough. Soil sampling locations were identified from the EM maps and navigated to using the real time GPS. Composite samples were collected by hand using a Dutch auger, from two locations, in increments of O-1 5, 15-30, 30-60 and 60- 90 cm. The analysis of the soil samples indicated a complete absence of nitrate or ammonium ions; the major anion was sulphate, indicating naturally saline subsoil conditions. The GEM 300 made the collection of data more efficient, as only one pass was required to collect the data from four depth intervals. The EM survey combined with the real time GPS allowed rapid characterization of the site with respect to soil salinity and proved to be cost-effective for Phase l/ Phase 2 site assessments and targeting sampling locations."

Jan 1, 1999

By Sandy Tavelli, Thomas L. Barkley

This discussion will present a case study in developing solutions to a metropolitan quarry’s public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over a four-month duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterization, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

By John Watson

New Technologies, New Challenges and New Opportunities For quite some time now, numerous explosive manufacturers have spent untold man-hours and millions of dollars trying to develop a blast initiation technology that would “once and for all” provide users with what was once believed to be only a theoretical possibility...nominal timing. Zero “cap scatter” (the amount of variation of delay timing from the targeted nominal) has been the industry’s goal ever since delays were first introduced into the marketplace. Just as adding delay time between blast-holes improved blast performance since their introduction, having the wrong delay or a poorly timed blast has proven to be very inefficient and in many cases hazardous. The question of how precise a blast initiation system needs to be still remains unanswered, but electronic detonator systems being used today indicate that significant improvements can be achieved over conventional pyrotechnic detonators. These systems can typically provide single digit millisecond ranges of variability, if not sub-millisecond in some cases.

Jan 1, 2003

By Greg Wyartt

"At an Australian iron ore open-cut mine, 129 separate blast patterns (consisting of 38.5 million tonnes /42.4 million US tons, equaling 28% of annual blasted tonnes) were initiated using electronic detonators. 87 patterns were designed as per site methodology using ‘vectorial’ initiation timing sequences (blast direction and relief specified only), while the remaining 42 patterns were designed with interactive initiation timing sequences - hole by hole sequencing based on the measured site specific primary shock wave (P-wave) velocity and distance between blast-holes. The intention of this project was primarily to reduce material size presented to the crushing circuit, and also to determine if productivity benefits could be obtained by the use of interactive timing."

Jan 1, 2017

By Greg Wyartt

Although electronic detonators and blast initiation systems have been commercially available for several decades, uptake in the Australian mining industry has been very slow when compared to other global mining regions. The safety and operational advantages of electronic initiation are generally well understood in Australia, however there has been a prevailing perception that these advantages do not outweigh the extra financial and technical investments.

Jan 1, 2019

By Frank Hammelmann, Peter Reinders

This paper briefly describes the past history of blast management. A modern blast management suite is then presented which demonstrates the current capability of the functional link between an electronic blasting system and blast design software. Finally, we look at the potential of tomorrow’s fully integrated blast management systems. From the first time blasting was introduced in mining as part of the production process, blasting technology and blast management have been interconnected. Over the past decades we have gained more recent experience with the new electronic blasting systems in mining, quarrying and construction. To start, the primary focus of electronic blasting was to increase timing accuracy. However, since then the technology has gradually developed, broadened and opened up new possibilities, including impressive flexibility in blast design and full in-situ verification of system functionality. To support this capability, modern electronic blasting systems are specifically designed to facilitate full two-way transfer of information between the office-based blast management software and field-hardened equipment. Blast management systems now comprise a suite of expert systems for planning, documentation, analysis, measurement and prediction of blasts. Within this blast management suite, the blast design software allows the transfer of the blast design information from a PC directly to the hardware of the electronic blasting system. The future development of this technology holds huge potential for the blasting industry.

Jan 1, 2004

By Steve Brace

Electronic detonators have been commercially available to the mining industry worldwide for over ten years. It is estimated that total cumulative global sales will have reached 25 million units by the time of the Conference in February 2004. This is below 0.2% of all detonator types sold during this period. Perhaps 20 million will have been used underground in South African gold, diamond and platinum mines. These will have been produced by South African companies, in South Africa for South African customers. Here efforts have met with greater success and in 2003 fully 5 million, or 3% of local detonators sold, could be of an electronic type. However, it is estimated that about US$7.00 (R50.00) has been expended on R & D, manufacturing facilities and marketing, for each unit so far sold. Large sums of money continue to be spent. Despite the apparent success in South Africa, is it justified? Electronic initiation systems have not produced significant technical benefits to the end-user underground nor corporate profits to the supplier. Some doubt they ever will (even from the large surface operations where the price per unit is much higher). A conclusion might be that they have failed. In 1998 Smit and Pistorius wrote a paper titled “Implications of the Dominant Design in Electronic Initiation Systems in the South African Mining Industry”. This ISEE paper seeks to summarise and review the conclusions of the earlier work. These were: that a dominant design had not yet emerged; the type of connector and the way in which detonators are connected and programmed would be a strong determinant influencing the development of a “winning” product; technical aspects rarely solely determine which becomes the dominant design (marketing, social and economic factors often have a strong influence); electronic initiation systems were an emerging technology for the underground gold mining industry in South Africa and because it was under severe cost pressure the mines would look to them to raise productivity and hence profits; finally, as a dominant design begins to emerge, one could expect a number of players to exit from the industry.

Jan 1, 2004

By Joshua Hoffman, William Chad Wedding, Braden Lusk

The emergence of electronic detonators as viable products for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. There are a number of commercially available systems that enable users to program delay times, usually in one-millisecond intervals, according to design decisions. While manufacturers have performed internal studies pertaining to the accuracy of these systems, an independent study quantifying the accuracy of the systems has not been completed to date. The mining industry is in the business of production and any quality control endeavors to independently confirm the accuracy studies performed by the manufacturers would only detract from their bottom lines. Furthermore, limited information is available concerning the accuracy of modern pyrotechnic delay based detonators. In 1985, the Bureau of mines completed a study of three manufacturers’ electric millisecond delay detonators (Bajpayee, 1985). This was the most recent extensive independent study performed on detonators, which unitized pyrotechnic delays, from numerous manufacturers. Advances in the manufacturing process for pyrotechnic delays may have increased the accuracy of detonators using these technologies in recent years. It is commonly accepted that electronic detonators are more accurate than both shock tube type non-electric as well as electric detonators, but the relative accuracy was not objectively and adequately quantified.

Jan 1, 2011