Search Documents

By John Platt, Mark Stephens

"When blasting is required in critical areas and anticipated shot movement and quick cleanup areessential to the success of the project it is extremely important to use the best technology available to achieve the goals expected by the customer. Wampum Hardware was given such a challenge in 2014-2015 when the PA Turnpike and New Enterprise Stone and Lime hired the company to do presplit blasting along the PA Turnpike. The face height averaged 45 feet (13.72m) and the shots had to be controlled to stop within 60-75 feet (18.29-22.86m) of the face or in this situation before they entered the travel lanes on the PA turnpike. In many if not most blasting environments, it is essential in controlling the movement of a blast, to make certain that the face holes are drilled at exactly the right place, with the proper amount and type of burden in front of and to the sides of the borehole. Profiling is an important first step to insure that the holes are drilled at exactly the right place and showing us the correct amount of burden in front of each and every drill hole."

Jan 1, 2016

By Eduardo Gonzalez Fernandez, Jaime Rios Vazquez

This report substantiates the connection that always exists between explosives and vibrations and draws attention to low frequency vibrations, which are the moat dangerous for the structures affected.

Jan 1, 1986

By Alfred Osborne

Progressive cavity type pumps are widely used by commercial explosive manufacturers for pumping water gel, emulsion and emulsion / ANFO blend explosives. Tests by explosives companies and investigations into incidents have shown that this type of pump can develop dangerously high temperatures when operated deadheaded or dry. [i.e. with no flow of product through the pump.] In some tests and incidents, explosion or detonation of the explosive (or residual explosive) in the pump has resulted.

Jan 1, 2002

By Cam Grundstrom

The Ok Tedi Mine is a large open pit copper and gold mine located in a remote section of the Western Province, Papua New Guinea, with an annual rainfall of over 10 metres. Ok Tedi mines an average of 205,000 tonnes per day. A strong working co-operation between the mine operator (Ok Tedi Mining Limited) and the explosives contractor (ICI Explosives Asia / Pacific) has led to progressive development of bulk emulsion formulations to meet site-specific needs, continued improvement to blasting applications, and competency based training programs for the national blast crew.

Jan 1, 1997

By Ethan Steward, Kyle Perry

Underground coal mines have several dangers, one the most hazardous of which is the possibility of an explosion caused by the ignition of methane gas. To reduce ventilation costs, coal mines have the option to close off abandoned areas that are no longer active with structural seals to keep an explosion from propagating into working areas of the mine. These seals must be designed to withstand different pressure levels based on the potential of the atmosphere behind the seal to become explosive, either 50 psi (345 kPa) for inert atmospheres, 120 psi (827 kPa) for non-inert, and over 120 psi (827 kPa) for special cases. Though seals have been designed to resist the overpressure, none have been evaluated for their resistance to the impact of heavy objects. Underground explosions produce high velocity gasses that, traveling through mine openings, may propel objects in the mine at a high velocity causing them to impact and damage the mine seals. Seals damaged in this manner may no longer hold the pressure they were originally rated for and may fail during subsequent explosions or leak explosive gasses into active workings. To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals. The velocity of each projectile is measured by an infrared chronometer which can later be used to determine its impact energy. Impact effects on the seals are measured using strain gauges, LIDAR scans before and after impact, high speed cameras, and visual inspection. The focus of this paper is on the projectile generator design and initial testing.

By Ethan Steward, Kyle Perry

To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals.

Feb 1, 2020

By Richard R. Brochu

At the International Society ofExplosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this wmmittee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give ‘results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same ,&thin stated tolerances.

Jan 1, 1998

By Kenneth K. Eltschlager, Richard R. Brochu

At the International Society of Explosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this committee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same within stated tolerances.

Jan 1, 1999

By D Linn Coursen

In the proposed method, the charges are elongated and arranged in one or more arrays. The orientation of each charge in an array, its velocity of propagation of explosion, and the velocity of propagation of vibration in the formation are such that, at an outlying location where vibration is to be reduced, the onset of vibration from explosion of the first negligibly small increment of each charge arrives a finite time before that from explosion of the last negligibly small increment of that charge. The charges of each array are fired in accurately-timed sequence, with the times between initiations chosen so that, at the outlying location, the onset of vibration from explosion of the last small increment of each charge, except the last charge, arrives a negligibly small increment of time before the onset of vibration from explosion of the first negligibly small increment of the succeeding charge. With such timing, vibration may be reduced at the widest range of locations by tilting the boreholes so that the terminal end of each charge is directly above or below the terminal end of the succeeding charge.

Jan 1, 1995

By Sterling Ziegler, Kameron Ray

Mining operations at a Wyoming coal mine were progressing to within 300 feet (91 meters) of a high pressure natural gas pipeline. Vibration levels from cast blasting were at a point at which standard designs would exceed permitted limits and could potentially damage the pipeline. Without a confident vibration model, mining would be unable to continue in the pit rendering an entire cut of otherwise mineable coal sterile. To safely blast in the area, linear superposition seedwave analysis techniques were attempted to be used to create a model that could accurately predict the vibration at the pipeline. Four signature holes were fired individually. The four signature waveforms were monitored at eight discrete locations to create thirty-two vibration data points. Two of the monitors were equipped with triggers enabling the calculation of p-wave velocity.

Jan 1, 2018

By Randall Wheeler, R. Frank Chiappetta

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation. and Explosives Applications - Orlando, Florida, USA July 24 - 27,200O 2000 BAI - PROTECTION AGAINST LITIGATION WITH GOOD PRE-BLAST SURVEYS, DAMAGE INSPECTIONS AND RECORD KEEPING 1 of 65 Good Record Keeping is Essential for: 1 ) Compliance with any prevailing Local, State or Federal Regulations, ordinances and permits. 2 ) Protection against potential litigation. 3 ) Balancing explosive consumption, use & costs. 4 ) Use in blast designs.5 ) Blast diagnostics & troubleshooting good/bad shots.

Jan 1, 2000

By Ralph E. Burnham, J. Kelly Ratliff

"The words “dynamite,” “TNT,” “explosives,” and “blasting” typically cause the general public, andjurors, apprehension and fear. Although blasting operations conducted by well-trained, skilled, andexperienced blasters rarely cause damage or injury, the public’s perception of blasting is that it isdangerous, disruptive, and results in damage to nearby properties. As a result, blasting operations have always resulted in complaints, claims, and lawsuits. However, in recent years, the public perception combined with an increase in public opposition, social media, more stringent regulations, predatory plaintiffs’ attorneys, and the application of strict liability to blasting claims has resulted in an increased threat of litigation to blasting companies and individual blasters. Consequently, many blasting companies find themselves receiving more complaints, involved in more litigation, and facing an alarming number of frivolous claims, which can result in increased insurance costs and other financial tolls. Accordingly, today’s blasting companies must be prepared for litigation and take steps to eliminate accidents and claims before the first shot is detonated on a job. The best way to accomplish this is standard operating procedures that incorporate best management practices, industry standards, and regulations in daily operations. This paper outlines some of the considerations that a blasting company should incorporate into its standard operating procedures before, during, and after the shot."

Jan 1, 2016

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Paul Worsey, Braden Lusk

Differences exist between public perception of construction blasting and quarry blasting. In general, people are able to tolerate short term inconveniences much better than long term ones. The paper focuses on the public perception of quarry blasting in St. Charles County, MO. This expanding urban environment has seen new legislation targeting preexisting quarry operations that have been in place for many years. A survey was made comprising interviews conducted to gauge perceptions of persons with varying demographics. Interviews covered topics involved with quarry blasting and its reporting methods. The purpose of the interviews was to determine public perception of blasting and how best to report results of vibration measurements. The use of different, less technically complicated measurement scales for vibration and airblast was considered as an alternative reporting system. The question for the industry is, “Has our past haste in adopting complex scientific scales and units been detrimental to us?” In other words, are we reporting the correct things? For airblast, the decibel scale was evaluated against millibar in the public eye. Peak Particle Velocity was also compared to that for displacement. Current legislation in the county is based on complaint levels rather than damage criteria. The complaints most likely not only come from ignorance to the affects of blasting on structures, but also sparse understanding of the units used to report these affects. The past practice of treading softly as an industry has been proven to be a poor choice, and education of the public as well as lawmakers on all levels is necessary. The Mississippi Valley Chapter of ISEE has begun to conduct seminars to this end. One educational seminar has taken place for officials and lawmakers in the St. Louis area, and others are in the planning stages. The focus of this paper is to gauge perception of the damage criteria reported today, and locate focal points for future education of the public in rapidly expanding suburban environments.

Jan 1, 2005

By Mark Fritzen

Drilling and blasting near residential or business inhabited areas may expose people to blast induced vibration. Many of these people have never been exposed to blast vibration and airblast which can cause a variety of reactions ranging from indifference to anger. Blasting contractors seeking to minimize the impact of blasting to neighbors of the project will plan for a public relation plan which begins at bid time. The public relations plan cost will be included in their proposal and a variety of methods may be included including, door to door contact, letters, pamphlets, telephone calls, and the use of an independent consultant to conduct a pre-blast survey. By raising the awareness of neighbors to a blasting project the blasting contractor may reduce the anxiety and stress of unannounced blasting vibration and airblast. This helps everyone associated with the project from the project owner(s) to the blasting contractor.

Jan 1, 2000

By Gregory B. Poole

As part of a $3.5 billion program to improve the antiquated waste water system in the city of Atlanta, the Nancy Creek Tunnel is being constructed across the northwest portion of the city. This tunnel is over eight miles long and is being constructed using Tunnel Boring Machines (TBM) for the majority of the tunnel and conventional drilling and blasting for three shafts, starter and tail tunnels and four connecting tunnels, totaling 2400 feet in length. An extensive public relations program was developed for this project. A group effort by the owner, engineer and contractor produced a public relations program that both informed and educated the public of the anticipated perceptions and effects of the blasting and TBM activities.

Jan 1, 2005

By Dave Harrison, Phyllis Hasser, Ken Eltschlager

The beginning There was the video:– “Understanding Vibrations from Blasting” – 2002 to 2004 in development – Dale Ramsey ad hoc Public Education committee chair – Available At the ISEE bookstore Public Education and Public Relations Committee • Standing ISEE committee 2004 • Co-Chairs – Ken Eltschlager, Dave Harrison • Purpose: "Develop and conduct programs on public education and public relations. Public education programs will focus on public awareness, understanding, and appreciation of the explosives industry. Public relations programs will concentrate on providing blasting professionals with the tools to assist in the public's understanding of the explosive industry and in the appropriate ways to respond to local community issues."

Jan 1, 2007

By I E. "Chip" Harris, G Alan Foster

Whilst a great deal of published data exists as to safe ground vibration and air blast levels which result from blasting little documented research has been carried out to determine how and why human beings complain about blasting operations. This paper gives the authors thoughts and experiences of why complaints arise and practical steps to minimize such complaints.

Jan 1, 1977