Search Documents

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012

By Jarrod Bonsmann, Zachary T. Plitt

"A surge in mine related deaths in Middle Eastern conflicts over the past few years has prompted research into the mitigation of the impact on a blast loaded vehicle. In past military conflicts, it has been observed that blast loading can cause injury to the brain but the exact cause is unknown [1]. The recent rise in deaths due to Improvised Explosive Devices (IEDs) has led to research that has speculated that the high acceleration experienced by soldiers on a blast loaded vehicle leads to Traumatic Brain Injury (TBI) [2]. This research aims to investigate vehicle designs that can reducethe peak acceleration for passengers on board the vehicle, in the event that the vehicle is blast loaded by an IED."

Jan 1, 2016

By Robert Benedetti

This paper describes various mitigation methods in order to reduce the maximum acceleration of the floorboard of hulled vehicles when explosive charges buried in water saturated sand were detonated beneath them. The effects on floorboard acceleration of adding a vehicle hull, several types of floorboard bracing, the use of foam to fill the gap between the floorboard and hull, and the use of foam to isolate the floorboard from the hull have been investigated. Small scale testing was conducted, which used bar magnet velocity gages to measure the velocity as a function of time of the center of the floorboard, directly over the charge, where the acceleration was expected to be greatest.

Jan 1, 2012

By Gregory Hempen, Thomas Keevin, Russell Wilcox, William Wild

The Department of Defense Strategic Environmental Research & Development Program (SERDP) awarded funding for evaluation of procedures to mitigate peak pressures and energy flux density in the water column from ordnance being detonated on the ocean floor. The research purpose was to conduct scaled testing to resolve whether a theoretically-viable covering technology was operationally effective in reducing blast effects and the impacts of shrapnel. An additional objective was testing effectiveness of this method for hard-bottom units (rock or coral) and (unconsolidated) sediment substrate.

Jan 1, 2011

By J Paul Tidman, Stephen H. Chung

One of the requirements in open pit gold mines is to minimise the mixing of ore and waste. Dilution can be reduced by choke blasting and control of the initiating sequencing. The authors have used the DMC computer model (developed at SANDIA) to examine the effects of timing and charge distribution on ore dilution. The model has been calibrated by measurements of vertical uplift derived from high speed videos made at the Dome Super Pit in Timmins.

Jan 1, 1997

By D T. Froedge

To preface these remarks, it is not intended that this paper be a criticism of anyone or any organization involved in drafting the current regulations, for it appears that everyone involved in the process has made an extreme effort to be safe. We wish to show that in this case by making huge safety margins, we have created an unsafe condition in another area. That is by creating vast safety margins in the area of mobile transmitter intensity versus distance scales we have caused a severe handicap in the use of the mobile transmitter in securing blasting areas. The use of these mobile transmitters, which are absolutely essential in clearing areas where there are woods, mountains, or urban structures is virtually eliminated because of the safety factors prescribed in the regulations. We wish to show that these mobile transmitter safety factors are much too great, and can be traded off to increase the margin of safety in the ability to clear blasting areas.

Jan 1, 1975

By J W. Edl, F C. Wu

In instrumented model rock blasting experiments in granite blocks, best fragmentation results were obtained when delays between holes were 1 to 2 milliseconds per ft. of burden and when a rectangular shothole pattern was used with spacings larger than the burden. Effective fragmentation in multiple hole blasts seemed to depend primarily on the full development of the crack network around each hole before the charge in the next hole was detonated. The test results showed that simultaneous or almost simultaneous initiation of shotholes in bench blasting resulted in poor fragmentation.

Jan 1, 1975

By Kai Nielsen

Drilling and blasting design results in a fragmentation that will have an important economic influence on all subsequent operations such as loading, transport secondary blasting and primary crushing.

Jan 1, 1987

By Lazar Kricak, Vladislav Kecojevic, Dragan Bogunovic

In spite of many advantages explosives have, their usage may cause environmental problem such as seismic vibration. One of the solutions to this particular problem may be application of an artificial screen as a barrier to the seismic wave path. This paper presents the results of experimental research on the artificial screen concept, its characteristics and role in attenuation of seismic effects generated by blasting. More than 1,500 laboratory measurements were conducted with different combinations of screen sizes, positions of the screen to blasting source, and intensities of blasting impulses. The results of the study show a significant reduction of generated vibrations by employment of artificial screens.

Jan 1, 2007

By Abraham Lindo

"Blasting plays a key role in hard rock underground mining. It is by nature a violent and destructiveextraction method designed to economically fragment the rock into a suitable size for it to be loaded and hauled as part of the specific mining process while controlling the amount of damage to the surrounding rock mass."

Jan 1, 2016

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

Feb 1, 2020

By Dale S. Preece, Stephen H. Chung

"A discrete element computer program named DMC_BLAST (Distinct Motion Code) has been underdevelopment since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC_BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993b)."

Jan 1, 1999

By R Yang, M Lownds

This paper reports studies showing the effects of delay scatter on the peak particle velocity (PPV) of blast vibration using a multiple seed wave (MSW) vibration model developed in recent years. The case studies also show the advantage of accurate delay timing on frequency control of blast vibration. The site parameters used in one of the studies are from a case in which the MSW model has been tested and confirmed to yield accurate predictions. This study uses an open pit blast design and a tunnel design in which blast vibrations using electronic detonators are compared with those from pyrotechnic detonators. Mean peak particle velocity (PPV) and the 97.5% upper bound PPV are compared. It is found that both these values increase significantly with the increase of the coefficient of variation of the site parameter. Using an open pit blast design, the modeling shows that electronic initiation shifts vibration energy to the expected frequency for a selected point of interest. However, for the same design of nominal initiation timing pyrotechnic detonators fail to shift vibration to the expected frequency due to its large scatter of timing.

Jan 1, 2011

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

By Leslie C. Taylor, Anthony L. Kee

Computational modeling of explosively loaded saturated sand on a suspended plate is an inherently complex problem. In this study a computational method is used to predict the dynamic pressure load/impulse from a buried charge. A fully coupled code modeling the explosive charge, sand and air with a Eulerian mesh and the plate structure with Lagrange elements, such as Gemini-Dyna, is an appropriate computational tool. In water-saturated sand, the loadings are soil and water-transmitted shock and bubble or blast effects depending on the depth and the charge size. The computations provide the capability to determine the total impulse load placed on a horizontal plate on or above the soil due to an explosion in the saturated sand for different burial depths in saturated sand and different plate stand off distances. The following test case will be presented: (a) 4.5 Kg (10 lbs) TNT, 10.16 cm (4 in) depth of burial to top of charge, and 20.32 cm (8 inch) stand off distance (Test 4).

Jan 1, 2005

By Jaime Herrero, Santiago Gómez, Pablo Segarra, José Ángel Sanchidrián

This paper presents a mathematical model for the study of the 2D movement of blast bench faces based on the high-speed video analysis of three blasts at El Aljibe quarry (Spain) recorded at 2,000 frames per second. In these blasts, a set of bags of 0.75 × 0.75 m were placed in front of a selected blasthole defining a reference plane in which to study the kinematics of the movement. The burdens range from 3.86 m to 5.54 m, with a bench height of 12–13 m. An affine transformation system was calculated to convert coordinates from the video images into actual spatial coordinates. The problem is established from a multi-objective minimization approach in order to simultaneously optimize two defined objectives: trajectory fitting using Total Least Squares regression, and time–displacement regression using Ordinary Least Squares. Muti-objective minimization formulation produces Pareto plots of non-dominated solutions, i.e., optimal combinations of initial velocities and response times, (i.e. time between detonation and the onset of bench face motion). From the Pareto frontier, the most balanced solution is selected. Blast response time lasts only a few milliseconds and appears so brief at the frame rate used that it is difficult to detect visually. In this context, the bi-objective optimization-based approach proves to be a more robust tool than frame-by frame survey for quantifying such a rapid event while also maintaining a strong performance in the trajectory fitting task. Root Mean Square Error (RMSE) for the two minimizations average 0.22 m and 0.13 m, respectively. The initial velocities obtained range from 4 to 17 m/s, and the response times 0.7 ms to 21.7 ms. An analytical model is also presented for predicting fragments initial velocity and response time as functions of blast geometry and rock mass properties, explaining approximately 87% of the total variability.

Jan 26, 2026

By B T. Lusk, Jhon J. Silva

"The original signature hole technique to predict vibration levels from blasting, is based on theassumption that each hole in a production blast, generates an identical vibration waveformarriving to the point of interest. When the same waveform is used to represent the vibrationproduced by each hole, the complete waveform for the whole blast is the convolution betweenthe waveform and the impulse sequence that represents the initiation timing of the blast. In thisresearch, several field tests were developed to establish the validity of the invariability of thewaveform hole-to-hole in a mining production blast. The results of the tests showed that thereare variations in amplitude and frequency content for the hole-to-hole waveforms. Thevariations can be explained due to the character of the parameters involved in a production blastbetween them: different vibration path for each hole, differences in the geometry of each hole,differences in the explosive charge for each hole (chemical and quantity), etc. This paperdescribes a methodology based on the main characteristics in both; time and frequency domainof any recorded signature waveform and uses Fourier series to approach one equation to generatedifferent random waveforms for each hole that can be used in the prediction of the completevibration record of the blast. The methodology is the base for signature hole analysis using aMonte Carlo scheme."

Jan 1, 2012

By Dale S. Preece, Stephen H. Chung

Explosives energy can be used effectively in breaking and displacing large volumes of rock in mining and quarrying industries in both open pit and underground. The blast result, however, may not be economical if the applied explosives energy distribution is not properly applied to match a given set of geometries. However, this engineering problem can be resolved by using a modeling approach in the blast design process. Starting with a given set of blast design parameters that include explosive, elastic properties of rock, geometry of the blast pattern as well as the delay firing time, this paper shows how a discrete element blast model can be set up to allow the examination of the effect of critical design input parameters on blast results. Examples are given in this paper to help visualize the value and application of blast simulations. They are (1) regular and terrace bench blasting models for throw control, (2) underground blasting including a drop raise opening and (3) collapsing of a multiple room-pillar structure with proper firing sequence to control the mixing of blasted materials.

Jan 1, 2005