Search Documents

By M. Kalin

Tailings deposits are frequently the source of ground water contamination due to the transport of contaminated tailings pore-water. If amendments to tailings covers could be made to facilitate a precipitation reaction and halt or reduce the generation of acid in pyritic tailings, the quality of pore-water quality would be improved which would in turn reduce the production of contaminants. The effects of phosphate wastes, added to base-metal mine tailings in Newfoundland, Canada, were tested. Laboratory and field experiments determined the effects of different mixing ratios of phosphate wastes to tailings volume (1:4, 1:8, 1:12 and 1:20, dry weight) for a total period of 3.2 years. The addition of phosphate at ratios of 1:4 to 1:12 substantially increased the pore water pH, and reduced both acidity and Zn concentrations. These results suggest that addition of phosphate wastes to tailings covers can reduce acidity generation and improve tailings pore-water quality.

Jan 1, 2004

By Pravin Mathur

"Praxair's CoJet® technology was introduced in 1997 to effectively inject chemical energy in electric arc furnaces. Coherent jets were invented as a revolutionary means of injecting oxygen and other gases into the EAF and into converters. Today, steel makers have widely accepted this concept in over 70 EAFs worldwide. Indeed, the whole industry has shifted to this new standard for chemical energy input in EAFs. CoJet® technology has also been implemented successfully in BOF converters.This paper will review the principles of coherent jets as applied to steelmaking. The key learnings garnered from several furnaces are also reviewed. In addition, while the CoJet® program has been widely accepted worldwide, based on steady feedback received from customers and the market place, several programs are underway in development and commercialization. These enhancements and new applications of CoJet® technology are also overviewed in the paper."

Jan 1, 2004

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004

By M. Sharafodin, A. A. Hassanipak

Abstract - The essential aims of additional borehole drilling are to improve the reliability of grade and tonnage estimates in each reserve class and to increase ore tonnages. The "GET" function presented in this paper considers strategies for achieving both of these goals simultaneously, and therefore is advantageous for selecting sites for additional boreholes. The "GET" function is either a linear or a non-linear product of three variables G, E, and T: f(G,E,T,) = G??E??T??where the values of any or all of the exponents ?, ?, and ??may differ from unity at the discretion of the user. G and E are the average estimated block grade and the average estimation error for ore blocks in one vertical column, and T is the compounded ore thickness within the column. To illustrate its utility, the GET function has been used for determination of the most advantageous sites for additional drilling in the Shah-Kuh Pb-Zn deposit in west central Iran.

Jan 1, 2004

By P. Hubert, J. P. Ildefonse, F. Qafssaoui, J. Poirier

Corrosion tests by corrosive alumina-lime slags were carried out on commercial high alumina bricks used in steel ladle linings and model refractories (with different raw materials : bauxite, andalusite, and different microstructures). Using (SEM) scanning electron microscope and (EDS) energy dispersive spectroscopy, microstructures of slag-corroded refractory interfaces were studied in detail. The monomineral and glassy phases, the composition of reaction products and chemical profiles were determined. A thermochemical analysis based on phase equilibrium diagrams has permitted to estimate the proportion and the composition of the high temperature intergranular liquid phase. These data were compared to the experimental microanalysis results. The viscosity of the high temperature liquids were calculated according to Urbain 's model and the relationship between the viscosity and the penetration of liquid phases were discussed. These theorical and experimental results were used to understand the complex phenomena of slag penetration and corrosion of andalusite and bauxite refractories at high temperature and to propose new ways of improvements for the formulation of high alumina refractories.

Jan 1, 2004

By S. H. Seyedein

A mathematical model was developed to study fluid flow and solidification in a single-roll casting system. Fluid flow coupled with energy equations were solved numerically using a finite volume method. A body-fitted coordinate transformation technique was adopted to handle the irregularly shaped domain. In order to couple the continuity and momentum equations, a SIMPLEC algorithm was used. A fixed-grid enthalpy method was considered to model the solidification in the system. The turbulence effect on flow field was modeled using a low-Re k-e model The model developed in this work was further run under various conditions to optimize the operating parameters of the process.

Jan 1, 2004

By K. Morikawa, K. Asano, J. Yoshitomi

The quality requirements for ladle shrouds have become stricter year by year to the pursuit of higher productivity and improved quality in the continuous casting of steel. The ladle shrouds must be sufficiently durable under severe conditions, such as operation without preheating and during several sequential castings. The consideration is that ceramic fibres, which have been applied in shrouds for thermal insulation during casting, could pose a risk to the worker's health. We realized materials for the ladle shrouds which show high strength and low elasticity. At the same time pursuing effective insulation, a coating which contains no fibres (Foaming Coat) has been developed, replacing the conventional one containing fibres. These materials are durable under conditions of repetitive use and consequently satisfy the customer's demands. The ladle shrouds which were improved in this way have achieved an excellent durable life in hot service of three times that of conventional ones. This paper reports the recent technological developments in ladle shrouds as well as their performance under hot operating conditions.

Jan 1, 2004

By D. Lunt

Telfer bulk concentrates typically contain 8% chalcopyrite, 8% chalcocite, 45% pyrite and 80-120 g/t gold. Although very high copper and gold recoveries can be obtained by subjecting the concentrate to a "conventional" high temperature pressure oxidation step followed by copper recovery by solvent extraction and electrowinning, and cyanidation of the leach residue for gold recovery, the cost of lime required for neutralisation and power for oxygen generation was such that the process was uneconomic in terms of operating costs. The challenge therefore was to develop an alternative flowsheet that maximised copper and gold recovery in which the reagent costs were commercially attractive. An additional objective was to reduce the capital cost so that the overall NPV and IRR values would enhance the economic viability of the total project. Following a series of batch and locked cycle testwork programs, supported by Metsim modelling, it was established that the same high levels of overall copper and gold recoveries can be obtained by use of a novel two-stage split leaching circuit in which the chalcocite component is leached in a low temperature (90-110°C) circuit with the chalcopyrite component treated in a high temperature (220-250°C) circuit. This split circuit has a number of advantages, including minimising the required capacity of the high temperature autoclave, as well as reducing the overall lime consumption and simplifying the total process water balance. The paper outlines the basis for the development of the flowsheet and discusses the integration of the leaching stages into the overall circuit.

Jan 1, 2004

By W. D. Gould, F. Goodazi, W. F. A. Duncan, A. G. Mattes

A biological treatment system designed to passively remove high concentrations of metals from leachate collected from a landfill near a large integrated zinc lead smelter has been in operation intermittently for the past five years including winter time operations. High metal removal efficiencies in the system were achieved. After 729 days of operation and treating over 8 million L of water the original anaerobic bioreactor constructed in 1997 was taken apart and rebuilt. The deconstruction of the bioreactor allowed systematic sampling at all depths of the biological matrix. Samples were analyzed for metal, S and TOC concentrations; as well bacterial populations were determined. Results of this sampling procedure are examined and compared at various depths within layers and between layers using one-way ANOVA and linear regressions. Metal concentrations were positively correlated with sulphur and negatively with total organic carbon. This is in concurrence with a model of biogenic precipitation of metal sulphides.

Jan 1, 2004

By Eugene Nel, Johan Theron, Chris Martin, Hans Raabe

"Impala Platinum Limited is the world’s second largest platinum producer, producing more than 1.7 million ounces of the precious metal last year, much of this from the UG-2 reef located in the Bushveld Complex, South Africa. As part of Impala’s ongoing expansion programme, tonnage through their principal UG-2 processing facility, near Rustenburg, was increased 40% in 2001.To accommodate the increased throughput, the role of the existing primary mills was converted from conventional semi-autogenous grinding units, to attrition and selective grinding units, operating in fully autogenous mode. The finer chromite and coarser silicate components in the mill discharge are then separated by screening and processed in dedicated circuits downstream. This way, the need to spend considerable capital to increase primary grinding capacity was averted.In the last year, considerable work has been conducted to evaluate and optimise the two downstream circuits. This has involved an optimisation programme of sampling and diagnostic flotation testing, supported with QemSCAN analysis. This paper will describe the operation of the new circuit. It will also describe some of the more novel aspects and interesting findings from the optimisation programme.INTRODUCTIONThe South African platinum industry is the world’s largest producer of platinum and the world’s second largest producer of palladium. Located in a wide area north of Johannesburg, the industry mines ores from the Bushveld Complex, one of the world’s great mineral treasure chests, containing over 70 percent of the world’s platinum, as well as extensive reserves of the other PGE (platinum group elements), chrome, manganese and vanadium. The industry employs about 180,000 people in, predominantly, underground mines, which together form an almost unbroken circle of mining operations 200 km in diameter."

Jan 1, 2004

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By L. Jiang

This report investigated the dynamic recrystallization (DRX) phenomenon in magnesium alloy AZ31 billets to understand the deformation mechanisms and microstructure evolution during extrusion and other metal forming processes, Compression tests of coarse-grained as-cast magnesium alloy billets containing lamellar Mg17Al12 eutectic phase and (Al, Mn) particles suggest that temperatures higher than 300°C, strains greater than 0,25 and strain rates above 0,l/s lead to the formation of fine DRX grains in the deformed samples. Microstructural observations also indicate particle-stimulated DRX nucleation (PSN) during hot deformation of the AZ31 alloy, facilitated by the presence of Mg17Al12 and (Al, Mn) particles, While the Mg17Al12 is dissolved into the matrix at about 350°C, (Al, Mn) particles may remain effective for PSN at temperatures up to at least 400°C, This study suggests that alloy design with a proper distribution of second-phase particles can provide the desired microstructure for improved properties and formability in wrought magnesium alloys.

Jan 1, 2004

By Geir M. Haarberg

Electrochemical techniques, mainly linear sweep voltammetry and potential step chronoamperometry, were used to study the behaviour of dissolved phosphorus species in cryolite-alumina melts, The presence of AIPO4 or Na3PO4 gave rise to voltammetric current waves due to electrode reactions involving phosphorus species at potentials where dissolved alumina is stable in cryolite melts, Diffusion kinetics for dissolved P(V) species were studied, Data from industrial cells were used to determine mass balances for phosphorus, For cells being fed with secondary alumina, more phosphorus tends to end up in the produced metal, Laboratory experiments to study the effect of phosphorus in the bath on the current efficiency for aluminium were also carried out.

Jan 1, 2004

By P. Wells

"In the past decade, there have been many developments in processing of nickel/copper sulfide ores. Improved pentlandite/pyrrhotite flotation selectivity with the use of new reagents, fine regrinding and Redox measurement (control) has led to increased pyrrhotite rejection and thus higher concentrate grades. Flash flotation has increased overall nickel and associated precious group metal recoveries. Recovery of both fine and coarse particles has been improved through an understanding of flotation cell hydrodynamics. The separation of copper from nickel in such ores has seen a similar level of development. From the late 80s to very recently, the use of flotation columns, the use of pyrrhotite depressing reagents and the improved understanding of the complex mineralogy of chalcopyrite, pentlandite and pyrrhotite have considerably increased copper / nickel separation efficiency. Copper concentrate with more than 30% copper and less than 0.5% nickel grade is now obtainable at 80-85% copper recovery from mill feed compared to 70-75% copper recovery with 30% copper and 1% nickel grade only a few years ago. Improved copper / nickel separation in milling operations has the potential to substantially improve the processing of the resulting concentrates and thus the overall return from the extraction of nickel and copper from sulfide ores.INTRODUCTIONNickel metal by itself or in alloys with other metals and materials makes a significant contribution to modern society. The relatively high price that nickel commands compared to other base metals is a reflection of the fact that, although abundant in the universe, nickel is sparingly distributed in the earth’s crust. There are two types of nickel deposits that are currently being exploited: complex sulfide ores and lateritic oxide ores. Lateritic contain no copper but in sulfide deposits, nickel– bearing minerals, principally pentlandite (Pn, [Ni,Fe]8S9), some millerite (NiS) and violarite ([Ni,Fe]S) are often found in association with copper-bearing minerals, mainly chalcopyrite (Cp, CuFeS2) and cubanite (CuFe2S3). The copper content of such ores can vary considerably from as high as 5-8% (in some Sudbury basin ores) to as low as 0.1% (in ores mined by Western Mining at Mount Keith, Western Australia and by Inco in Thompson, Manitoba). The valuable minerals Pn and Cp are almost invariably found associated with pyrrhotite (Po, Fe7S8) which along with nonsulphide rock has to be rejected to tails in the primary milling stage. The bulk concentrate from the primary stage is then treated to depress Pn and float Cp. A complete Cu/Ni separation at the mill would be highly desirable but this is not possible because of locking between a small fraction of the valuable minerals. As a result, Cu/Ni separation has to be carried out both during milling and during refining of the matte following smelting. At Inco, Jinchuan and in Norilsk, a chalcocite / heazlewoodite separation is made by flotation following slow cooling of the matte. In the present Sudbury Inco operations, Cu/Ni separation has not been conducted at the mill since 1991 and all Cu/Ni separation takes place at the matte processing plant. Because of the rising ratio of Cu to Ni in the ore, this strategy is under review and this paper describes some recent studies of circuits in preparation for possible installation of a copper / nickel separation circuit at Inco’s Clarabelle Mill in the Sudbury area."

Jan 1, 2004

By J. Ji

Oxygen requirement during acidic pressure oxidation of sulphide concentrates can he as high as 800 kg/(m3.h) in the first compartment of an autoclave when the total oxidation residence time is shortened to 30 minutes. To achieve such a high oxygen transfer rate while maintaining satisfactory oxygen utilization, a pilot plant campaign was launched at the Placer Dome Research Centre in 1998 to measure the oxygen mass transfer coefficient in a 5 m3 pressure vessel at a total pressure close to 500 psig with a 30 HP gassing agitator. Maximum oxygen flowrate to the pressure vessel was designed at 3 600 kg/h. In this paper, a great deal of information is provided on the gassing agitator, pressure vessel. measurement procedure and results. Without oxygen sparging, the oxygen mass transfer coefficient is 2 600 h-1 with a mixing power input of 5.0 kW/m3 in solution. With oxygen sparging, the oxygen mass transfer coefficient increases to 3 500 h-1 with a mixing power input of 4.0 kW/m3 in solution.

Jan 1, 2004

By A. Liem, R. L. Johnson, C. Sturgess, E. Kuzub

New challenges in mineral processing arise as high-grade ores become less available and the mining industry is forced to exploit lower grade ores. One of the challenges in beneficiating lower grade ores is the liberation of mineral particles while maintaining control over material management. Lower grade ores need fine grinding to free valuable minerals, but finely divided particles can cause severe problems, such as dustiness and flowability, in subsequent stages of material management. There are at least two approaches that can be taken to resolve this dilemma, both of which relate to particle size enlargement. First, the application of a dust suppressant can be used to control that aspect of material management. The optimal choice of dust suppressant agent depends on effectiveness and cost, both of which can be strongly influenced by the selection of application method. Second, agglomeration combining small particles into larger units-can reduce dust and improve the flow characteristics of the material at the same time. There are several mechanisms that can be employed to agglomerate mineral materials. Although agglomeration adds a new processing step, it is often cost effective. This paper describes these two approaches and their respective challenges, as they relate to a mined ore. We report on modified or newly developed procedures for characterizing mineral ores with respect to material management. On the same material, we use agglomeration processing to capture fines within larger particles and show how dustiness and other aspects of material handling are affected. We conclude by discussing their specific application in accordance with the mineral properties and processing needs.

Jan 1, 2004

By M. Spreij, M. Hogenboom

Refractory lining performance of aluminium melting and holding furnaces and downtime due to refractory re-linings, are important parameters for increasing the aluminium output of a cast house and decreasing costs. The importance of refractory materials testing is illustrated by examples of improvements made in refractory lining concepts, quality control and introduction of alternative and newly developed materials. These examples also show that the information given by product definitions of refractory suppliers will in many cases be insufficient to judge the risks and benefits of using alternative materials.

Jan 1, 2004

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By Y. Faitakis, G. J. Powley, C. Mackenzie

"In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production.It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About onethird of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations:The first generation (1940–1950): A “fix it when it broke” attitude prevailed during that time, mostly because the industry was not highly automated.The second generation (1950–1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly.The third generation (1980–): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex multi-functional teams become responsible for maintenance.At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance."

Jan 1, 2004