Search Documents

By Michael Cooper, Eric Konigsmann, A. Moerman

"A paste backfill plant and underground piping distribution system was commissioned at the Brunswick Mine in June, 1998. Concentrator tailings, composed mainly of pyrite and lesser amounts of silicate minerals with a P80 of 37um (45 YO-20 pm), are pumped to the backfill plant. The backfill plant uses conventional thickening and disc filtering to dewater the solids, which are then mixed with binder in twin screw mixers. The paste is discharged through a gob hopper and one of three boreholes by gravity. Approximately 65% of the concentrator tailings will be placed underground at full production. The remaining thickened tailings will be pumped to an existing impoundment area. Application of paste technology will completely replace the use of cemented rock fill in the mine by the end of 1998.The design capacity of the paste backfill plant is a total of 360 dmtph of cemented paste through two parallel production lines. The plant is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher ProVox Distributed Control System that is in communication with the property information highway. Video and audio signals from the underground system are carried to the surface plant via a leaky feeder communications/fiber optic system.The underground distribution system consists of a network of 200mm diameter boreholes and piping. There are approximately 3.5km of boreholes and 5.5km of piping in the system. To minimize pressures, the greatest piping length from any borehole is approximately 400m with all piping being open-ended. There are no valves in the entire paste distribution system.Construction of the plant, including installation of piping to and from the plant and preparation of the underground distribution system, was completed in less than one year from the time of management approval for the $M 22.3 project."

Jan 1, 1999

By Ted J. Williams

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

May 1, 2007

By Hugh K. Taylor

"With some justification, people have long complained about the indefinition of ore reserves. Perhaps they were led to expect too much; from former and easier definition practices in the once common underground mines with exposed and available assets, where the obsolete term 'ore in sight' was at least partly literal. But such mines have become rarer, and their underground development less affordable. For most projects, valuations and its definitions have thus been advanced from actual to prospective mines, leaving a very wide gulf between 'what is there' and 'what may happen to it'. This brings the double challenges of reduced geological and technical assurance and the protraction of economic uncertainties.This paper avoids the popular field of regional resources, being confined to what may possibly be mined within single or closely grouped deposits. For these, many estimates of tonnage and grade must be made, defined and declared long before assessment of feasibility; and the uncertainties of the latter make it an unsound base for defining the earlier quantities. Despite the best of intentions, implied or inferred promises may proveimpossible to honour.A simpler framework of definitions is suggested, to some extent reverting to an earlier dependence on supporting work rather than on opinions of economic assurance or future events that are more properly the functions of production and cash flow schedules."

Jan 1, 1994

By S. Klingmann

ABSTRACT In this paper, we used data collected from the Gibraltar mine to analyze the effect of the TyreSense tire monitoring system on tire performance by reducing tire wear and preventing premature tire failure or damage. We analyzed the relationship between tire temperature, tire pressure, and tire failure or damage to help better understand the importance of controlling high tire temperature and pressure. The results enhance and expand the knowledge of the management of tire operational pressure and temperature.

Jan 1, 2014

By R. D. Clarke, E. De Souza

"A framework for ventilation planning, with a focus on planning to the end-of-mine life, was developed for the Diavik Diamond Mine, Northwest Territories. This framework was successfully used by Diavik’s mine engineers to select a cost-effective ventilation plan that met the life-of-mine requirements. The framework achieved this result by reconciling the production plan with the ventilation plan. A set of design acceptability criteria was created and a PICK (possible, implement, challenge, kill) chart was used to quickly narrow down the generated ideas for detailed assessment and economic analysis. RÉSUMÉ Un cadre de planification de l’aérage, qui met notamment l’accent sur la planification jusqu’à la fin de vie de la mine, a été développé pour la mine de diamants Diavik. Les ingénieurs miniers de Diavik ont su mettre à profit ce cadre pour sélectionner un plan d’aérage rentable qui répondait aux exigences propres à la durée de vie de la mine. C’est en conciliant le plan de production et le plan d’aérage que cet objectif a pu être atteint. Un ensemble de critères d’acceptabilité de la conception a été créé et un tableau PICK (de l’anglais possible, implement, challenge, kill, une méthode donnant la priorité à certaines actions proposées ou à des idées visant à résoudre des problèmes) a été utilisé pour rapidement limiter les idées générées et les soumettre à une évaluation et une analyse économique détaillées.INTRODUCTION The Diavik Diamond Mine, Northwest Territories, has been an underground-only operation since 2012 and has a remaining mine life of 8 years. In the first year of underground-only operations, the production rate increased from 60 kt of ore per month to more than 160 kt of ore per month. In subsequent years, this rate was continuously increased (Table 1) because the operation went through various improvement initiatives. By the end of 2016, Diavik’s total production was 0.41 Mt (+22.8%) ahead of the 2012 budget for 2016 production."

Jan 1, 2018

By L. Xia, B. Hart, G. Gingras, M. Furlotte

Plant and laboratory test work was performed in order to optimize a copper/zinc flotation separation circuit at Matagami concentrator, Canada. The testing identified a significant difference between the laboratory testing and the plant flotation, particularly for the sphalerite recovery in the rougher copper concentrate. Tests indicate that sphalerite recovery of the flotation concentrate in the laboratory testing was significantly higher than in the plant. The ToF-SIMS surface analysis identifies surface species responsible for the discrepancy in Zn recovery. It shows that sphalerite flotation is in response to the collector attachment and a significant enrichment of Cu on the surface of sphalerite grains. A comparative surface chemical analysis was performed on both sphalerite and chalcopyrite grains from the plant flotation and laboratory testing in order to identify surface species variability between the two testing. Two significant observations were revealed. First, there is considerably more hydrophilic iron oxyhydroxide on sphalerite surface from the plant flotation sample relative to those from the lab testing. The secondary coating likely completely or partially passivates sphalerite surfaces, reducing Cu enrichment and hence sphalerite floatability. Secondly, comparing the surface chemistry on sphalerite and chalcopyrite, the hydrophilic iron oxyhydroxide species have preference for the sphalerite grains relative to chalcopyrite. Despite numerous studies on the effect of galvanic coupling during grinding, there is limited documented evidence on the effect of the milling environment on the flotation and plant operations. This observation suggests that interaction between sulphide minerals and grinding media have a significant influence on subsequent flotation. This paper discusses the results of a detailed surface chemical evaluation of sphalerite grains from both the plant and laboratory testing in the context of grinding environments and pulp chemistry.

Jan 1, 2016

By D. S. Hines

The purchase of mechanical equipment for mines is not unlike the purchase of other materials or supplies in general principle, but on account of the major part such equipment plays in the operations, and of the fact that life and valuable property are at stake, the matter demands the most careful attention on the part of the purchaser. The problems and difficulties encountered are dealt with below in their sequence in the purchasing procedure. Requisiting Although it is quite a common practice to submit a tentative specification of requirements to recognized manufacturers of equipment- soliciting alternative propositions or recommendations for study in the selection of certain equipment-as a rule the first step in purchasing procedure is the requisition. Primarily, it is the form that carries to the purchasing department the record of equipment wanted. A full and complete description or specification, and accuracy of record, are the important points to be insisted on in a requisition. Too much attention cannot be given to this detail, as this is one of 'the most important phases of purchasing work. Incomplete information, either in specification or detail, leads to delay in handling the requisition, and, if not detected in the purchasing department, may mean receipt of material which cannot be used for the purpose intended. In addition to description of material or equipment to be ordered, the requisition should also show where or what the equipment is for, whether for operating or new work. If for capital account, the number of the authority for expenditure should be given for record and distribution purposes.

Jan 1, 1930

By R. B. Smith, D. C. Brady

"A review of the major renovation of the fifty-year old C-I headframe facilities at NERCQ's Con Mine, Yellowknife, N. W.T. is provided. The project was complete with only two 3-day shutdowns of the facility .Work consisted of four major phases: structural reinforcement of the adjoining mill building prior to dismantling; relocation of virtually all mine and mill utilities which transited the headframe collar en route from the adjacent powerhouse; dismantling of the entire headframe facility and portion of the mill building, including the removal of asbestos siding; and erection of a new headframe, idler rower, collarhouse and mill wall.This paper describes the work and methods used by NERCQ, J.S. Redpath Mining Consultants Limited, Acres International Limited, and others to bring the project to a successful completion. The history of the project is discussed from the planning phase through construction, including; design, procurement, and construction scheduling. The paper discusses the unique elements of the project, the problems encountered, and the methods used to achieve success.IntroductionThe Con Mine is a 800 tpd gold operation located in Yellowknife, Northwest Territories. Originally owned and operated by Cominco Limited , the Con Mine was sold in December 1986 to NERCO Minerals Company, and officially renamed NERCO Con Mine, Ltd. The Con Mine has been in operation for over 50 years. The first gold brick ever produced in the Northwest Territories was poured at the Con Mine in 1938. The original C-1 shaft was sunk in 1937 to a depth of 235 ft. In 1941 the shaft was deepened to a depth of 950 ft, and the original timber head frame was replaced with a steel structure. Following the discovery of the Campbell Shear in 1946, the C-l shaft was again deepened to its present depth of 2443 ft. Over the years, mine production gradually moved deeper and further from the C-l shaft."

Jan 1, 1991

By Xiao Huang, Jean-Francois Thibault, Ali Merati, Prakash C. Patnaik

Single-crystal nickel-based superalloys are the current state-of-the-art technology for the manufacture of turbine blades. This technological improvement of the turbine blade has brought a considerable increase in its cost. Repair and overhaul of service stressed single crystal turbine components is an economic necessity for life cycle cost reduction of engines since the cost associated with replacement is significantly higher than its counterpart polycrystalline component. This paper will first review the recently reported research in developing repair technologies used for DS and SX components. These techniques repair the crack or defect while at the same time ensuring that the mechanical properties do not deteriorate and, more importantly, that the single-crystal microstructure is not jeopardized. It will then be followed by a brief overview of the research conducted and initiated by the authors with regards to the repair of single crystal alloys.

Jan 1, 2004

By Andrea Lisjak Bradley

Clay shales are currently being assessed as possible host rock formations for the deep geological disposal of radioactive waste. However, one main concern is that the favourable long-term isolation properties of the intact rock mass could be negatively affected by the formation of an excavation damaged zone (EDZ) around the underground openings. The goal of this thesis was to develop and validate a mechanically-based model of the deformation and failure process of a clay shale, namely Opalinus Clay (OPA), with particular focus on the influence of anisotropy on the short-term response of circular tunnels. To achieve this goal, a hybrid continuum-discontinuum numerical approach was developed in combination with new field measurements from the Mont Terri underground research laboratory. The response of OPA during the excavation of a full-scale emplacement (FE) test tunnel was characterized by geodetic monitoring of wall displacements, radial extensometers and longitudinal inclinometers. The deformation measurements indicated strong directionality induced by the combined effect of in-situ stress field and bedding planes striking parallel to the tunnel axis, with the most severe deformation occurring in the direction approximately perpendicular to the material layering. Computer simulations were conducted using a newly-extended combined finite-discrete element method (FEM/DEM), a numerical technique which allows the explicit simulation of brittle fracturing and associated seismicity. The numerical experimentation firstly focused on the laboratory-scale analysis of failure processes (e.g., acoustic activity) in brittle rocks, and on the role of strength and modulus anisotropy in the failure behaviour of OPA in tension and compression. The fracturing behaviour of unsupported circular excavations in laminated rock masses was then analyzed under different in-situ stress conditions. Lastly, the proposed modelling methodology was applied to the aforementioned FE tunnel to obtain unique insights into the EDZ formation process around emplacement tunnels for nuclear waste. The calibrated numerical model suggested delamination along bedding planes and subsequent extensional fracturing as key mechanisms of the damage process potentially leading to buckling and spalling phenomena. Overall, the research findings are already having a direct impact on the preliminary design process of an underground repository for nuclear waste in Switzerland.

Jan 1, 2015

By A. J. Hyett, N. Hedrick, J. Blackall

The Garford bulb anchor is a modified cable geometry developed and patented by Garford Ply Ltd. of Australia, and which has recently become widely available in Canada. It is produced by deforming the seven wires (including the central kingwire) of a standard cable into a bulb" (Fig. 1). Laboratory cable pull tests indicate that the bond capacity of the 25 mm Garford bulb anchor is comparable to the nutcase cable, in excess of the birdcage cable, and significantly higher than standard 7-wire strand. Its comparative advantage over the latter is most significant for tests at low radial confinement and high water:cement ratio grout, which corresponds to operational conditions of low quality rock (i.e. weak, highly fractured rock masses, foliated hanging walls, failed ground, etc.) and poor installation quality control (perhaps the most common explanation for cable bolt failures). It is under such conditions that cable bolting is often ineffective. The most impressive result is that for a reduction of the effective rock mass modulus by a factor of five, the Garford bulb cable capacity remains virtually unchanged.

Jan 1, 1995

By Abdurrahman Tosun

It is very important for after blasting processes that muck pile fragmentation is predicted and controlled during blasting. Therefore, a significant research effort has been devoted to the development of mathematical equations that predict the value of average muck pile fragmentation. The specific charge parameter used in all of these equations is determined as the ratio of the total mass of explosives used to break a volume of rock. The length of blast surface and the row number of the blasthole are ignored in the calculation of the specific charge. However, in a blasting operation, blasthole geometry may result in additional material being impacted by a blasthole. This is due to effect shares of in both end sides of blastholes and the back region of blasting surface. In this study, a total of 14 blast tests, 8 at the first quarry and 6 at the second quarry of the Bati Anadolu (Western Anatolia) Cement Factory, were performed. In each study area blast tests were designed in the same direction continuously to provide stable structural properties of the rock. Therefore muck pile fragmentation depended on only specific charge values for each blast tests. Specific charge values were calculated according to both an average blasthole and also the total volume of material occurred as a result of blasting for each blast tests. During loading until the end of blasted material the front, the back, the arm off and the bucket off pump hydraulic pressure values occurred in hydraulic pistons of the loader were determined with a lot of data received for each blast tests. After that the relationships between specific charges values obtained according to two different methods and hydraulic pressure values of the loader were established with two correlations. The relationships between specific charges values obtained according to the total volume of material occurred as a result of blasting and hydraulic pressure values of the loader occurred as the best results especially the blasting operations that have the total length of blasting surfaces are short.

Aug 1, 2013

By Franc R. Joubin

"Gold has been found in many parts of the Bridge River district of British Columbia; but it is from a relatively small area in the valley of Cadwallader creek that most production has come. The ore-bearing area measures 1/2 mile in width by 3 miles in length; and for convenience it is called the Cadwallader gold belt in this paper. In this belt are found the Bralorne and Pioneer mines and in addition several prospects under development.The gold of the Cadwallader gold belt occurs in quartz veins averaging about 3 feet in width and containing about ½ oz. of gold a ton. Except for a relatively small amount of silver, no other metals are produced from these veins. The ore-bearing veins occur in a variety of rocks. They occupy reverse faults and tension fractures belonging to a distinctive fracture system. Some of these structures are ore-bearing over lengths exceeding 5,000 feet and depths exceeding 3,700 feet. The production of the Bralorne mine (1932-1945) is 996,383 oz. gold and 190,709 oz. silver; that of the Pioneer mine (1930-1945) is 777,588 oz. gold and 135,698 oz. silver. These two mines have together distributed about $25,000,000 in dividends.The Bridge River district first attracted attention in 1863* when prospectors were attracted by its small but rich placer gold deposits. Most of the important lode deposits of the Cadwallader gold belt were discovered in 1897 (11). Many years of desultory development followed and it was not until 1928 and 1932 that the Pioneer and Bralorne mines, respectivdy, entered into profitable production."

Jan 1, 1954

By Ainul Akhtar, Steve Cockcroft, Jixiang Xu, Daan Maijer, Lu Yao

"Nitrogen rich Ti-N inclusions are one of the more difficult inclusions to remove during liquid metal refining of titanium. If present in the final component, they can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading. Understanding the kinetics of dissolution of Ti-N particles during consolidation/melting of titanium can help us better operate and design the melting processes to minimize their occurrence in Premium Quality Titanium production. A numerical model based on finite difference method has been developed to calculate the dissolution of a spherical Ti-N particles in molten titanium. Analytical solutions were used to verify the finite difference code for calculation of concentration profile and the dissolution of spherical solids. Taking into account the limitations in these approaches for the different cases examined, the invariant field approximation showed good agreement with the results from the numerical analysis. Evolution of the size of a spherical Ti-N particle during dissolution was predicted by the numerical model and the particle dissolves in 163 s.INTRODUCTION Properties like low density, high specific strength and excellent corrosion resistance make titanium attractive for a variety of applications. Key characteristics in the processing of titanium and its alloys include its high sensitivity to impurities, especially atmospheric oxygen and nitrogen and its high reactivity in the molten state. Nitrogen rich inclusions Ti-N, also known as Type ? or hard alpha defects, usually have substantially higher hardness and lower ductility than the surrounding material. Because they can act as fatigue initiation sites, Ti-N inclusions can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading, even in minor amounts (tenth of a percent) (Lampman, 1990; Moiseyev, 2005; Lütjering & Williams, 2007). Ti-N encompasses as a broad range of nitrogen contents from a few wt% up to stoichiometric TiN. The liquidus temperature of Ti-N titanium increases substantially with increasing nitrogen content. Consequently, depending on the concentration of nitrogen, the melting point of Ti-N inclusions can be above bulk liquid metal temperatures during melt processing. Thus, removal of Ti-N defects hinges on dissolution and not melting."

Jan 1, 2017

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

By D. Seo, P. Au, X. Husang, D. Nagy

The production of single crystal (SX) turbine blades represents the current stateof- the-art in Ni-based superalloy design. With complex casting processes and alloy composition modifications, SX superalloys exhibit superior high temperature mechanical properties to their polycrystalline counterparts. Stresses and plastic deformation can occur in SX nickel-base superalloy engine components at various stages during their manufacture and use. For examples, stresses are created during initial solidification and also during solid state processing such as shot peening, grit blasting, blending, electrodischarge machining and welding. Stresses may also be created during service due to random events such as foreign object impacts. Subsequent exposure of SX to high temperatures during solution heat treatment and brazing repair can result in recrystallization which has been shown to be detrimental to both creep rupture strength and fatigue performance of the components. It is therefore the objective of this paper to understand the recrystallization behavior of two SX superalloys, PWA 1484 and 1483, subjected to pre-stressing and subsequent heat treatments.

Jan 1, 2006

By E. C. Grunsky, B. W. Smee

"The development of low-cost, rapid multielement analytical techniques has generated large geochemical databases in many exploration programs. When a sampling program consists of several thousand samples, the resulting data matrix is enormous and effective interpretation using all of the elements individually becomes burdensome. However, the application of multivariate statistical techniques can extract geochemical patterns related to the underlying geology, weathering, alteration and mineralization. Imaging the results over topography enhances the interpretation of these patterns. Examples of this approach are shown from mineral exploration programs in Canada and Mexico. IntroductionThere has been a dramatic change in the effectiveness of using geochemical survey data in the past ten years. This is mostly due to:• lower cost of geochemical analysis;• lower detection limits;• new methods of multi-element analysis;• a marked decrease in the turnaround time;and• the intelligent use of computers in presenting geochemical data.Geochemical surveys commonly have two objectives: locating abnormal concentrations of ore-forming or pathfinder elements and characterizing the underlying host lithologies. Geochemical surveys often employ a wide range of sample media that may typically include whole rock lithogeochemistry, various soil horizons, till and basal till sampling, stream sediments, lake sediments, and various forms of weathered regolith. Each of these sample media will exhibit a unique element distribution that must be factored in the interpretation phase of a geochemical survey study. This can become a cumbersome process if univariate data handling methods are employed."

Jan 1, 2003

By L. Xia, B. Hart, K. Douglas

In the flotation of Rare Earth Element (REE) bearing minerals, oxalic acid is reportedly acting both as a depressant and pH modifier. Testing has established the significance of oxalic acid in the flotation process however its specific role in either the recovery or selectivity of REE over their gangue minerals is not well understood. Pulp pH reduction trials with alternative acids have not shown the same effect on the REE mineral recovery or the depression of gangue phases. This work examines the effect of oxalic acid on the surface of gangue minerals (quartz and carbonates (dolomite and calcite)) in a series of conditioning tests. Gangue surface analyses by TOF-SIMS indicate that oxalic acid inhibits the transfer of secondary ions generated during the conditioning process from one mineral phase to another. In this regard, the oxalate anion acts to fix ions in solution through chelation, limiting their participation in surface adsorption.

Jan 1, 2014

By Benoît Plante

La mine Tio (QIT Fer et Titane Inc.) exploite à ciel ouvert un gisement d?ilménite massive depuis 1950, générant jusqu?à maintenant plus de 70 Mt de roches stériles potentiellement génératrices de drainage neutre contaminé (DNC), dont une partie est submergée dans le lac Petitpas, au nord de la mine. Si généralement l?ennoiement des rejets miniers a un effet bénéfique pour limiter la contamination des eaux, cela reste à prouver pour ce qui est des stériles générateurs de DNC. Des essais en réservoirs ont été réalisés afin d?évaluer la réactivité de trois différents types de stériles submergés, qui ont été choisis en fonction de leur teneur en ilménite. Afin d?évaluer l?impact de la matière organique sur la réactivité des stériles submergés, chaque type de stérile est étudié en immersion simple ainsi que combinée à des sédiments prélevés au lac Allard, à proximité de la mine, d?où l?eau utilisée dans les essais a aussi été prélevée. L?évolution des teneurs en Ca, Mg, Si et Ni durant les 8 premiers mois d?étude démontrent que les stériles immergés sont réactifs, mais l?impact de la matière organique demeure pour l?instant difficile à préciser. Tank tests on Tio mine waste rock The Tio mine (QIT Iron and Titanium Inc.) exploits a massive ilmenite ore as an open pit since 1950, producing over 70Mt of potentially contaminated neutral drainage (CND)-generating waste rocks. While the underwater disposal of mine wastes generally show a beneficial effect on water contamination, this method still needs to be approved for CND-generating waste rocks. Tank tests were realized in order to evaluate the reactivity in underwater conditions of 3 different waste rock types, chosen with regards to their ilmenite content. In order to evaluate the impact of organic matter on the reactivity of underwater waste rock, each waste rock type was studied in simple immersion and in combination with sediments sampled at Allard lake, located near the mine, where the water for the tests was also sampled. The evolution of Ca, Mg, Si and Ni during the 8 first months of testing show that the waste rocks are reactive underwater, but the impact of the organic matter is till hard to define.

Nov 1, 2008

By Benoit Bissonnette

"The need for production of a competent fill was recognized early by the project partners. Consequently, a 4000 Ud paste fill plant was constructed and commissioned in early August 1994.In order to fine tune the process without risk to the underground workings, a closed pumping loop was devised on surface. After two months of this exercise, the first underground slope was filled according to specifications obtained from the pilot plant trials.This paper will focus on the operational problems encountered and the solutions adopted so far, and on a comparison between expected and actual fill production and characteristics.RésuméLa nécessité de produire un remblai de propriétés mécaniques suffisantes a été rapidement reconnue par les partenaires du projet. Conséquemment, une usine de production de remblai en pate, utilisant les residus du concentrateur d'une capacité de 4000 t/j a été construite et l'opération a débuté au mois d'aôut 1994.Dans le but de roder le précedé sans mettre en danger les installations souterraines, l'usine a été testée dans un circuit de surface. Après deux mois d'essais, le premier chantier souterrain a été rempli avec du remblai en pate selon les specifications dérivées de l'usinage pilote.Cet article présente les problemes d'opération rencontrés et leurs solutions, en plus de faire une comparaison entre les résultats prévus et ceux actuellement obtenus sur la production et sur les charactéristiques du remblai."

Jan 1, 1996