Search Documents

By W. T. Martson

ABSTRACT Sooner or later, every producing mine faces the question of fill. This paper invites consideration of mill tailings as an economical, efficient, and quantitatively adequate source of such fill. Some of the advantages, disadvantages, methods of utilization, and methods of treating mill tailings for sand recovery are covered. ADVANTAGES AND DISADVANTAGES OF SAND FILL DISREGARDING economic com-promise, that material which supports the greatest applied load with the least compression is the best choice for fill. Table I, reproduced from U. S. Bureau of Mines Bulletin 60, is offered as evidence of the adequacy of hydraulically placed sand. Table II gives the results of tests made in an effort to determine the reason for the difference between load hearing qualities of dry-placed and hydraulically-placed sand. From these, it would appear that hydraulic placing gives a denser initial packing, with corresponding higher, and faster development of, load bearing qualities. Assuming this to be true, then if sand from mill tailings can be placed underground economically, it is the superior fill material. Table III summarizes cost data available. The most cursory glance through the available references (2, 5, 6, 7, 8, 9) will show .that the major benefit from the adoption of sand fill is a decrease in the non-productive fill ?cycle of a working place. This, it is estimated, increases the output of an individual stope by from 25 to 50 per cent. The advantage of reducing the number of required working places for a constant daily production is obvious.

Jan 1, 1951

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

By W. G. McBride

The mining industry has already become highly technical in all its branches and this has brought about specialization in mining engineering. Increasing demand for mineral products, exhaustion of high-grade or easily worked deposits, and narrowing of the fields for exploration and development, are forcing mines to greater depth and to working material of lower grade and more complex composition. The Robinson Deep at its Turf shaft has reached a depth of 7,640 feet and expects to go to 8,500 feet; Miami Copper, under normal market conditions, profitably mines ore running only 16 pounds of copper to the ton; Alaska Juneau is making a profit on ore running about $1.15 per ton in gold; and many mines are handling ores of an extremely complex nature. In each case, the success of these operations has depended upon the application of sound scientific principles and good business methods to the problems involved. It may be safely assumed that mining at great depth and the exploitation of low-grade, or complex, ores will become more and more important as time goes on, and this means that greater and greater demands will be made upon the technical skill and business ability of the mining engineer. To meet this condition, the more or less haphazard methods of training the young engineer that have prevailed in the past will have to be replaced by a careful and well-ordered system of engineer-training. Upon the industry and the older mining engineer falls the duty of providing means to assist the deserving student to prepare himself properly to meet the increased demands that are falling upon his profession. Consideration of the training of the mining engineer involves a decision as to what constitutes his field of usefulness. Technical control of methods and processes obviously falls upon the engineer, but there are still many who doubt his usefulness in the executive field, particularly in positions involving close contact with the men and work. Many engineers have failed as shift-boss or foreman, but this has been generally due to fault in the management in using men who were temperamentally unfit to lead others or who lacked the necessary preliminary training.

Jan 1, 1932

By D. Naden, D. J. King

"The high capital and operating cost of liquid-solid separation circuits in hydrometallurgical plants has led to an increased focus on the use of in-pulp systems for metals recovery in order to eliminate the need for solids washing and to reduce the need for liquid-solid separation.Carbon-in-pulp (CIP) has now been accepted in Canada and around the world as the leading process for recovery of gold and silver, replacing the Merrill-Crowe process and thus removing the need for CCD thickeners or belt and drum filters. The overall design of conventional CIP adsorption circuits was established in the late 1970s and it has remained substantially unchanged until now. Most of the development work since 'hen has been concentrated on improving methods of separating pulp and carbon and on reducing carbon losses during transportation and agitation.Resin-in-pulp (RIP) has been used for many years in uranium mills in the USA. However, most of the plants were built in the 1960°s and RIP was only chosen when liquid-solid separation of leach pulps proved very difficult. The plants are far from ideal as they have high resin losses and high maintenance costs. Consequently, there is room for improvement.Davy McKee has taken a fresh look at the engineering development of in-pulp contactors leading to a fundamental redesign of the adsorption units. The improved in-pulp technology uses a modification of the proven air-swept screen techno1ogy together with a new technique of process operation. The new contactor operates at high pulp throughput rates with high concentrations of carbon or resin in the recovery stages, resulting in a significant reduction in the contactor size over conventional design. As a result of this reduction in the size of the contactor by up to 80%, significant savings can be made in equipment and building costs. In addition, the plant 1s easier to operate than a conventional CIP plant."

Jan 1, 1987

By Bo-Hyun Kim

Outline ? Strainburst criteria and hypotheses adapted for this study. ? Influence of excavation method on rock mass properties. ? Excavation disturbance factors vs. deformation modulus, etc. ? Estimation of blasting damage zone around excavation. ? Considerations of energy on burst-prone ground. ? Literature review & closed form solution. ? Numerical simulations. ? Summary and future works.

Oct 1, 2010

By R. H. Colquhoun, A. W. Bolland, H. J. H. Pieterse

"American Barrick Resources Corporation acquired the goldstrike property in north eastern Nevada in early 1987. Since that time, the company has undertaken an extensive development program. This paper will overview the milling, autoclaving, and heap leaching facilities which are part of the $400-million Betze development plan. Gold production at the Mine has increased from 40,000 ounces per annum in 1987 to more than 500,000 ounces in 1991. And in 1992 Goldstrike will be the single largest North American gold mine when it produces 1,000,000 ounces.1. SUMMARYAmerican Barrick Resources Corporation acquired the Goldstrike property in northeastern Nevada in early 1987. Since that time, the company has undertaken an extensive development program. This paper will overview the milling, autoclaving, and heap leaching facilities which are part of the four year, $440- million Betze Development Plan. Gold production at the Goldstrike Mine has increased from 40,000 ounces per annum in 1987 to more than 500,000 ounces in 1991. In 1992, Goldstrike will be one of the largest North American gold mines, when it produces appro approximately 1,000,000 ounces.2. INTRODUCTIONAmerican Barrick Resources Corporation is in the process of developing the Betze gold deposit, located on Barrick's Goldstrike property in the Carlin area of Nevada, U.S.A.The Goldstrike Mine has 17.9 million ounces of proven and probable reserves and an additional 460,000 ounces of possible reserves. Additionally, the Purple Vein deposit, one mile north of the Mine, is expected to add at least 4 million ounces of reserves by year end 1991.The Goldstrike ore body contains both oxide and sulphide ore. The largest part of the reserves are contained in the high grade, deep sulphide ore. Mining of the sulphide ore contained in the Betze deposit involves the removal of large quantities of overlying oxide ore. Oxide ore is treated through one of the following processes:-"

Jan 1, 1992

By C. E. Rodgers

WHEN the writer was engaged early last year by Canadian Comstock and its subsidiary, the Metropolitan Electric Company, to act as Consulting Mining Engineer in connection with the layout and equipment of the new ore-dressing laboratories at Laval University, Quebec, the metallurgical laboratory section of the School of Mines building was completely erected, including plastered walls, partitions, etc., and finished concrete floors. At that time, however, no equipment had been ordered, except three Dominion ball-mills and two Bell screening machines. ADVANCED OR CONTINUOUS LABORATORIES The continuous laboratory section of the Department occupies the basement and three floors of the building, with an approximate floor area of 9,000 square feet. Because of limitations imposed by the design of the building (height and arrangement of rooms, strength and design of floors, etc.), modifications of layout from what otherwise seemed most desirable were, of necessity, made. These included: (a) Omission of automatic sampling of the dry ore. (b) Complete elimination of inclined belt-conveyors through floors. (c) Exclusion of bucket elevators for either dry or wet ore transfer. (d) As a substitute for grill-covered drains and floor sumps, drainage from sections or from individual pieces of equipment was piped to a disposal system in the basement. (e) Substitution in several instances of fabricated steel in place of the usual concrete foundations for machinery. (f) Reducing floor cutting and area of such opening to a minimum. Ore storage and chute capacity above the basement level was also minimized to reduce total weight.

Jan 1, 1941

By A. A. Ruitenberg, G. Ruitenberg, J. Chandra

"The Caledonian Belt is mainly underlain by Late Precambrian and possibly Early Palaeozoic rocks, which are in part overlain by younger strata. Most of these rocks are weakly deformed, except for those in some linear . zones, which have been intensely deformed by cataclasis. Mineral deposits related to two distinct metallization episodes have been recognized. The earliest are zinccopper- lead sulphide deposits, which have been concentrated in the axial regions of late-stage cross-folds within the main cataclastic zone. The host rocks are andesitic and dacitic tuffs which show effects of intense talcose alteration, silicification and chloritization. Deposits related to the second episode are mainly composed of copper sulphides with locally abundant tennantite and tetrahedrite, which occur in brecciated and fractured carbonate-quartz veins. These veins postdate the late-stage cross-folds. VLF-EM and high-sensitivity magnetics proved to be very effective in delineating the geology of these deposits."

Jan 1, 1972

By Ray Collier

MINING TODAY l EXTENSIVE AND EXPENSIVE PERMITTING PROCESSES WITH UNKNOWN RESULTS l GENERAL AND IMPASSIONED RESISTANCE TO RESOURCE BASED INDUSTRY l SOPHISTICATED, ORGANISED, AND WELL FUNDED OPPOSITION l MOST LOCAL GOVERNMENT DOESN?T WANT MINING TODAY?S TALK l FOUR SPECIFIC OPERATIONS ON WHICH OUR EXPERIENCE IS BASED ? SECHELT ? CADMAN ? GRANVILLE ISLAND ? LEHIGH CEMENT DELTA PLANT l OUR APPROACH TO COMMUNITY RELATIONS

May 1, 2002

By R. W. Nice

Presently about 60% of the world's nickel resources are tied up with lateritic ores while about 25% of the world's nickel is produced from sulphides. Based on this the industry has to focus on improving lateritic nickel economics in order to maintain the high use of the metal worldwide. In 1997 three junior mining companies in Australia organised finance against all odds and commenced development of three separate nickel and cobalt extraction plants treating lateritic nickel ores. All three projects utilise similar pressure acid leaching (PAL) technologies while each has unique metal recovery technologies All projects have experienced numerous processing and maintenance related difficulties such that full ore throughput has been reached by only one operation after five years. This shortfall in performance has caused the owners considerable angst and financial pain. In 2000 Cawse went into receivership and was purchased by an international corporation. Recently, Bulong also went into receivership and has undergone an orderly shutdown, awaiting sale to a new buyer. Murrin Murrin has settled with its financiers and is in a position to operate as planned for many years forward. This paper will discuss a number of the technical difficulties that affect the ore preparation, PAL and solution treatment circuits of these plants. The objective is to identify the cause of some of the difficulties and propose possible solutions so that the next generation of lateritic operations can emerge as technically and, more importantly, economic successes. A number of these process improvements have been identified by the existing operators and in many instances have been or are being implemented into the existing operations.

Jan 1, 2004

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By A. E. Boudreau

It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydro thermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward-migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

"The McArthur River uranium deposit is the single richest uranium ore body developed in the world to date. The ore body’s average grade is 15% U3O8. Proven reserves are in excess of 450 million pounds. The grinding circuit is located underground. The ground ore is pumped to a surface facility where the slurry is thickened and loaded into containers for shipping to the Key Lake mill 78 kilometers to the south.The paper will briefly describe the mining method employed. The underground ore handling and grinding circuit, and surface facilities including slurry load out, wastewater treatment and the freeze plant will be described in detail. The paper will emphasize radiation and safety procedures that are followed to minimize operator exposure to radiation risks.LOCATIONThe McArthur River mine is located 78 kilometres north of the Key Lake mill. It is located at latitude 57’ N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pinehouse, located 320 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYThe McArthur River Operation is jointly owned by Cameco Corporation (69.805%) and Cogema Resources Inc. (30.195%). Exploration for uranium in the McArthur River area started in 1980 by the Saskatchewan Mining Development Corporation, a predecessor company of Cameco.In 1984, a 12-kilometre long basement conductor was identified at a depth exceeding 500 metres. Systematic exploration drilling of this conductor resulted in the discovery of the P2 North deposit. Subsequent surface drilling programs from 1989 to 1992 delineated a narrow ore zone over a strike length of 1700 meters at a depth of 500 to 600 metres. At this time, geological reserves for the deposit were estimated to be 2.4 million tonnes at a grade of 5.0% U3O8 for a uranium content of 260 million pounds U308"

Jan 1, 2001

By J. Lipp

The lion share of lithium produced globally originates from South American salars. The standard operation for lithium production utilizes an array of evaporation ponds. This process consume vast areas and is either very slow when relying on solar evaporation - roughly 18 months of residence time; or with very high energy consumption since over 90% of initial water volume needs to be evaporated. A new technology, based on solvent extraction was developed. Results indicate a distribution coefficient up to 30, and selectivity greater than 1,000 towards Na extraction. The loaded solvent is stripped using a strong mineral acid, and the product solution is the lithium derivative of that stripping acid. Utilization of this new LiSXTM technology results in reducing the area needed for a commercial plant as well as reduces the residence time. In addition applying different stripping acids can diversify the product line of such facility.

Jan 1, 2014

"The Code was developed in 2004 through the Collaboration Agreement between Institution of Mining Engineers of Chile (IIMCh) and the Ministry of Mining (Chile) in Dec 2002. It is an amalgamation of current practices with respect to standards and procedures for exploration prospects, mineral resources, and reserves for the purpose of public reporting. Certification is required to prepare and issue information on mineral assets according to the guidelines that regulate the technical, economic, and environmental aspects that satisfy the conditions set by the Chilean capital and financial markets.The Mineral Resources Committee of the Instititution of Mining Engineers of Chile (IIMCh) is pleased to introduce theCode for the Certification of Exploration Prospects, Mineral Resources and Reserves which is the result of a Collaboration Agreement between the IIMCh and the Ministry of Mining established in December, 2002.This code synthetizes the present practice of the mining industry in regard to standards and procedures applied to exploration prospects, mineral resources, and reserves with the purpose of reporting publicly on financial instruments based on these mine assets in the capital markets. These standards follow general criteria already adopted and applied by capital markets in those countries characterized by a very dynamic and well developed mining sector such as Australia, Canada, Southafrica, United Kingdom, and others. The work done by the Mineral Resources Committee of the IIMCh has had the recognition of the Combined Reserves International Reporting Standards Committee (CRIRSCO) that leads the establishement of an international code in these matters. CRIRISCO is an entity formed by representatives of the countries previously mentioned, a representative of the Society of Mining Engineers of the UStates and a representative of the IIMCh. The Institution thanks the Ministry of Mining, the representatives of these Ministry in the Mineral Resources Committee, and specially the Minister of Mining, Sr. Alfonso Dulanto Rencoret due to the genuine support given to the IIMCh in the preparation of this Code.The Institution also thanks the Superintendencia de Valores y Seguros (SVS) because of the help given continuously to the Committee as well as by the interchange of opinions and suggestions received during the preparation of this document."

Jan 1, 2003

By J. L. Dion

"A study of the techniques to integrally cast copper tubes in copper tuyeres for use in blast furnaces has been carried out. The work has been performed in support of current efforts to produce two-compartment tuyeres having improved water-cooling capacity. A test pattern corresponding to a vertical section of a two-compartment tuyere, and including a cast-in-place copper tube, was used to investigate such variables as tube preparation, tube coolant, pouring temperature, pouring rate and gating design. Successful castings, either with a good metalfurgical bond or good intimate contact between the tube and the casting, were produced, with all combinations of gating system and position of the tube tried. However, the pouring temperature, the pouring rate and the effectiveness of the coolant are interrelated and must be controlled to produce a good metallurgical bond.IntroductionAs part of its contribution to, and in collaboration with, the Copper Casting for the Steel Industry Committee, CANMET has undertaken research into the methods and techniques needed for the integral casting of copper tubes into high-conductivity copper castings.The objective was to produce two-compartment copper blast furnace tuyeres in which the water-cooled nose compartment consists of a copper tube metallurgically bonded to the wall of the high-conductivity copper casting. This design, developed in the UK, has demonstrated a much extended service life with attendant economies; unscheduled shutdown of blast furnaces due to tuyere failure is a significant problem in the steel industry. The Canadian steel industry believes that this design will replace the currently used single-compartment tuyere in blast furnaces within a few years.The technology to produce these tuyeres does not exist in Canada. One of the main features is the inclusion of a smooth-walled cooling channel in the nose, which permits high velocity cooling water to be employed. A second compartment acts as a reservoir backup, should failure in the nose occur. This would allow continued use of the tuyere for a period of time, permitting a scheduled shutdown for repair s. To assist the Canadian producers of tuyeres to maintain their market, and the Canadian steel industry to have a reliable domestic supply, it is important that the necessary technology for the production of two-compartment tuyeres be developed and transferred to industry."

Jan 1, 1982

By Les Johnston

_ BACKGROUND - About EPCOR - Genesee Generating Station - Phase 3 Expansion _ TECHNOLOGY SELECTION - Selection Criteria - Combustion Options - Flue Gas Emission Control Options _ STAKEHOLDER VIEWS _ PROJECT STATUS _ EPCOR is an integrated utility company for water, gas, electricity and technology services. _ EPCOR has about 1.6 million customers in Alberta, Ontario, Manitoba, BC, and the U.S. Pacific Northwest. _ EPCOR Generation Inc. operates three power stations in Alberta which were in operation before deregulation, including the coal-fired Genesee Generating Station. _ EPCOR Power Development Corporation owns generating stations in Alberta, BC and Washington State and will be building the Genesee Phase 3 expansion.

May 1, 2002

By Leon J. Perrier

The paper describes the equipment in use, haulage grades, road conditions, tire sizes, tire performance and related problems. Various types of failures and causes, corrective action taken, tire records and reporting for control are also discussed.

Jan 1, 1977

By F. Chiesa

Experimental results on thin and thick castings poured in aluminum A356 and magnesium AZ91E by the low pressure permanent mold process have been compared to the result of filling simulations for thin and thick castings. If the results of modeling is reliable when the liquid remains above the liquidus temperature, this is no longer the case when partial solidification occurs. The visco-elastic behavior of a partially solidified liquid is difficult to put into equation as it depends on the amount of shear it has been been subjected to. Attempts to predict misruns with a commercial software has been proven to be very difficult if not impossible; divergence of the numerical solution has been observed unless prohibitively long computing times are used. In order to overcome these difficulties from a practical standpoint, a simple method is proposed which consists in tracking the temperature of the advancing liquid metal front so as to make sure it will always be above so-called `Misrun Critical Temperature' (MCT) determined experimentally for thin and thick aluminum A356 and magnesium AZ91E castings. If the liquid metal front falls below this temperature, a cold-shut or misrun is likely to happen at this location. The values of MCT for thin and thick in aluminum A356 and magnesium AZ91E were determined experimentally on misrun castings of extreme geometries (a thin 2.5 mm wall cover and a 6mm to 25 mm thick bell housing). MCT was found to be lower for magnesium AZ91E and for the thicker castings.

Jan 1, 2011