Search Documents

By James F. Allan

"Abstract -The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec . Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by ? 0.10% Y203, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% Zr02. The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and cale-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and rninor britholite. Yttrium also occurs in britholite in cale-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By Pierre Laliberté

Introduction ??Mine ventilation is a major consumer of power in underground mining, including air heating (winter) and air conditioning (deep mines). ??Any advances, including the development of low emission vehicles, that can improve underground air quality can reduce ventilation demand, and likewise reduce costs and energy consumption, including their associated greenhouse gas emissions.

Nov 1, 2011

By Y. Luo

The rock breakage process in drilling is a main source of noise in roof bolting operations, especially when hard rocks are encountered. Proper control of drilling operation can provide an opportunity to improve energy efficiency of drilling and to reduce noise and heat generated from bit-rock friction. Drilling tests have been conducted in laboratory settings to confirm this noise-reduction strategy. Preliminary results show that the drilling parameters, penetration and rotational rates can be controlled to achieve in a desirable range in drilling medium hard rock. Based on the theoretical and experimental studies, rational drilling control strategy is developed for noise control while maintaining a safe and productive roof bolting operation. Applying this strategy in underground roof bolting operation, the noise exposure of roof bolter operators will be significantly reduced.

Aug 1, 2013

By Mark B. Thorpe

Golden Star Resources started gold mining operations in Africa in 1999 after 15 years of exploration in South America. At the time, the approach to local assistance was through "alternative livelihood" programs and the donation of infrastructure to local communities. This was initially successful with local community support. However, with time and on reviewing the implemented projects, it became evident that the success was limited and many if the projects were either poorly used or in disrepair. Through a review of the options, we decided to develop a community assistance model driven by the communities themselves, while keeping control of the finances and the actual construction of the projects. Through the formation of the Golden Star Development Foundation, we began to support community driven projects for local economic development. The evolution of economic development projects continued over the next several years with the addition of project requirements for partnerships with government, and finally an evolution to a partnered turn-key piece of infrastructure that we hand over to an agency for operation and ongoing maintenance. We are currently working with outside partners to further our economic development activities in Ghana to the benefit of our stakeholders.

May 1, 2011

By J. S. Godard

The mining developments in western Quebec have shown the ores of this district to be more complex in character than was at first expected. When the initial discoveries were made it was thought that the ores would be similar in character to those of Kirkland Lake and Porcupine areas. Developments have since shown that although the ores along the southern margin of the belt are somewhat similar, those within the belt, constituting by far the greater proportion, are vastly different, being complex mixtures of base-metal sulphides carrying values in the precious metals. These mixtures of base-metal sulphides of copper, zinc, and iron, present several problems to the metallurgist, especially in their concentration into marketable products. For the purpose .of this paper the following classification may be made of the ores of the district. Group I. - Milling Ores: (a) Ores in which~ arsenopyrite is the predominating sulphide. In this class of ore the gold occurs in fractures in the quartz and is associated to a lesser extent with the arsenopyrite and pyrite. Examples of this class of ore are the Granada, south of Pelletier lake, and the O'Brien and the Thompson in Cadillac township. (b) Ores in which iron pyrite is the predominating sulphide and gold is the valuable constituent. This may also be classed as a concentrating ore-Group III.

Jan 1, 1928

By Werner W. Scholz

A corrosion-resistant lining is, quite often, selected on the merits of its corrosion resistance only. This paper demonstrates the effects of temperature, pressure, weather, design aspects and variances of physical properties within the scope of the generic designation of a corrosion-resistant material or materials. The base for the study is a rubber- and brick-lined steel vessel, with unchanged chemical conditions. Graphs and sketches illustrate the various effects of physical influences on the selected lining specifications.

Jan 1, 1979

By A. Abdollahi

Modification of the silicon in Al-Si alloys can be performed by adding a very small amount of some elements like Na, Sr and Ca to alter the form of silicon from an acicular shape to a fine fibrous one. This modification results in a considerable improvement in mechanical properties especially elongation, Metallographic observations in A356 alloy indicated the degree of the modification with Na, Sr and Ca, They showed that the effect of Ca as a modifier is not as strong as is Na or Sr while Na is the most effective modifier, Although modifiers improve mechanical properties, they also increase porosity in castings, The reduced pressure test (RPT) and Tatur test showed that the increasing porosity with Na is the most and with Sr is the least.

Jan 1, 2004

By Fathi Habashi, Ahmet Deniz Bas

"The mechanism of leaching of semiconducting minerals such as PbS, ZnS, UO2, etc., has been the subject of intensive speculation by hydrometallurgy researchers in the early 1950s who assumed the formation of intermediate surface complexes that could be neither separated nor identified by physicochemical techniques. The electrochemical theory of leaching introduced in the late 1960s resolved this problem by comparing the leaching process to a corrosion phenomenon similar to the corrosion of metals. Few years later, experimental evidence showed that anodic and cathodic zones are formed on the dissolving mineral although no electric current is imposed on the mineral during dissolution. A discussion of these findings is outlined.INTRODUCTIONIn the early 1950s researchers realized that kinetic studies for leaching ores are as important as thermodynamic calculations. It was also during this period that the concept of species adsorption on mineral surfaces has dominated the interpretation of the mechanisms of most reactions. This may have been due to the fact that many researchers of this period came from the mineral dressing sector and were influenced by flotation theories. However, when the knowledge of lattice defects and the semiconductivity of minerals became known and their importance in extractive metallurgy was realized, there was a need to explain the leaching reactions in light of these modern theories (Habashi, 1969, 1970). Semiconducting minerals of importance in metallurgy are two categories: the sulfides such as those of copper, lead, zinc, and the oxides such as those of uranium."

Jan 1, 2016

By C. W. Drury

It is practically fifteen years since stellite was first introduced into industry, and since then the progress made in its manufacture has been so rapid and the number of successful applications so varied that it was considered a review of the more important phases would be of general interest. Stellite is a cobalt-chromium-tungsten alloy, containing approximately 2. 75 per cent carbon. The high percentage of carbon is necessary for the requisite hardness and resistance to wear at ordinary temperatures, whereas the tungsten is essential to impart hardness at a red heat. Chromium imparts hardness and strength, and cobalt renders the alloys more resistant to oxidation. The metals cobalt and chromium are completely soluble in all proportions, both in the liquid and solid state, the equilibrium diagram showing a minimum in the solubility curve at approximately 50 per cent cobalt and l,340°C. Cobalt and tungsten are completely soluble up to 40 per cent tungsten, which is beyond the limit of the; tungsten content of stellite alloys. In the presence of carbon, carbides are formed, which are essential in stellite possessing good cutting or wearing properties.

Jan 1, 1930

By C. Sorel

The PAREX code has been developed since the nineties by CEA and AREVA to describe the PUREX process implemented in the French fuel reprocessing plants. It enables the calculation, either in steady or transitory states, of the behaviour of the different elements of interest at each process step. The high customized structure of the software allowed the implementation of various phenomenological models describing solvent extraction systems dedicated to uranium purification from crude ore to spent fuel. After qualification of the implemented models, the code was used to perform the design of flowsheets, for safety demonstration analysis or for operational assistance.

Aug 1, 2010

AT the Annual General Meeting held in Winnipeg last March, the whole of one of the technical sessions was devoted to a special Symposium on Geological Investigations in Canada, introduced by a paper entitled The Geological Survey (lî which had been specially prepared by Dr. G. A. Young, Chief Geologist of the Survey, and had been published in the February BULLETIN, prior to the meeting. Geologists from each of the provinces contributed to the Symposium, including directing officials of the geological divisions of provincial Departments of Mines, representative geologists from the Universities, and company and consulting geologists. Space, unfortunately, does not permit publication of a complete record of the proceedings,_ or even inclusion of all contributions to the discussion. The following summary, however, gives what is believed to be a fair cross-section of the opinions expressed by representatives from each Province. The Symposium resolved itself largely into a discussion as to how the Geological Survey and the several provincial bureaus or divisions of geology could co-operate most effectively in the important task of carrying out geo-logical investigations, with avoidance of duplication of work and waste of effort, and, so far as broad principles are concerned, there was remarkably close agreement among those participating in the Symposium as to how the various types of investigation should be allocated as between the Federal and Provincial organizations. Briefly, the concensus was that the Geological Survey can render the most effective assistance by conducting reconnaissance investigations, with mapping at 4 miles to one inch, leaving to the provincial organizations the more detailed, and hence more local, studies and mapping at larger scales. There was general agreement that the preparation of base maps, essential to systematic geological investigation, is a service devolving upon the Federal Government.

Jan 1, 1940

By C. Van Den Heuvel, C. B. Van Buuren

BIOX® has been successfully demonstrated over the past 2 decades for the recovery of gold from refractory sulphide concentrates. To date 12 successful BIOX® plants have been installed in 8 countries spanning 4 continents with the 13th installation currently nearing completion in the Philippines. In 2010 BIOMIN introduced the ASTER™ process for improved water balances in commercial BIOX® applications by supporting tightening environmental legislation on water usage and availability in both arid and tropical regions. Previously, a common challenge for BIOX® plants was the inability to recycle thiocyanate containing water due to the low tolerance of the organisms. ASTER™, a biological thiocyanate and cyanide destruction process, renders a non-toxic solution for re-use in BIOX®. Two commercial ASTER™ plants are in operation with the 3rd ASTER™ plant under construction in the Philippines. A 3rd BIOMIN technology, specifically developed for double refractory ores is available for implementation. The HiTeCC process has shown considerable success on ores where competition from disseminated carbon has rendered ineffective gold recoveries. Through HiTeCC, gold is desorbed from the carbonaceous matter by manipulating the ionic strength and temperature of conventionally treated CIL product. One Australian commercial plant utilises HiTeCC while a 2nd installation is set for commissioning 4th Quarter 2014. BIOMIN’s premier solutions for refractory gold processing are described herein.

Jan 1, 2014

By Baseer Abdul, Edouard Asselin

Hydrometallurgical leaching of sulfide concentrates of copper and nickel at medium temperature (150°C) produces residues that contain sulfur and iron bearing minerals and phases. During leaching, and depending on various process parameters, iron may be precipitated as hematite, goethite, jarosite or other oxyhydroxides, which may be more or less crystalline. Hematite is the favored precipitate because it is the most environmentally stable and does not ad/absorb as much copper, nickel or other solution constituents during precipitation. However, the low solubility of iron during the medium temperature processing of sulfide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. In some cases these phases have been positively identified as the metastable ferrihydrite, which transforms into iron oxides such as goethite, hematite and magnetite over time. A better understanding of what may help drive this transformation during leaching would ultimately result in lower valuable metal losses and more stable leach residues. Higher acid concentrations result in increased copper extractions and favor the formation of hematite during concentrate leaching, rather than other metastable phases. Furthermore, commercially available water displacement formula “WD40®” and other novel reagent(s) affect Fe precipitation and sulfur chemistry, leading to very different process outcomes such as improved extractions and larger, more easily separated, sulfur particles.

Jan 1, 2017

By J. Walker, G. E. Kim

Since May of 2000, Mogas Industries, in partnership with F.W. Gartner Thermal Spraying Co. and using the services of Perpetual Technologies, has invested time, energy, and resources towards developing novel ball valves for high-pressure acid-leach (HPAL) service. In addition to developing new valve designs, an aggressive coatings development effort has been undertaken to improve the protective quality of the coatings so as to enhance the performance and extend the life of valves in severe HPAL conditions. In 2001, Mogas Industries qualified and applied a nanostructured titanium oxide (n-TiO2) coating for gold and nickel/cobalt HPAL services. The n-TiO2 coating provided dramatically superior protection against abrasive and erosive wear, fared very well against high-pressure autoclave corrosion testing, and has performed well in HPAL service.

Jan 1, 2004

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By W. A. MacWilliams, R. G. Reynolds

"This paper describes, for the first time, a patented method of extracting sodium sulphate from a natural deposit in Western Canada. The method resembles, but is not, strictly speaking, solution mining. The fact that a plant based on this method has been in successful operation since late 1969 will be of added interest. The deposit in question is located near Metiskow, Alberta, and conventional surface recovery methods could not be applied because of heavy concentrations of mud. Considerable pilot work went into the separation and recovery process on which the plant operation is based. The history of the industry is covered briefly as background to this development. Today it is clear that the method has broader application within the industry and, in concept, may generate interest in many other applications."

Jan 1, 1973

By W. Beres, Li. J.

The finite element method (FEM) has been applied to investigate the stress fields and deformation of a TiN/Ti-6A1-4V coating/substrate system subjected to nanoindentation. MSC Patran and MSC Marc were used to prepare the three-dimensional finite element models and to perform the simulations of the Vickers nanoindentation experiments. Pure silicon and TiN/Ti-6A1-4V coating/substrate system were analyzed. The properties of the materials were assumed to be homogeneous and isotropic with a linear hardening behavior. The reverse method was used to extract material properties, such as the yield stress and strain hardening coefficient, from the numerical results by comparing the simulated indentation load vs. penetration depth (P-h) curves with those obtained experimentally. Both non-linear elastic and non-linear elastic-plastic analyses were carried out for the coating/substrate system. The results are given for four different coating thicknesses.

Jan 1, 2004

By R. R. Montigny

A brief description is given of the history, location and geology of the Granisle Copper Limited operation on Copper I land in Babine Lake. Detailed information is given with regard to pit design, planning, drilling, blasting, excavation and haulage. Equipment maintenance and mining costs are also presented.

Jan 1, 1971

By D. E. Deegan, G. Holcroft, T. P. Johnson

"The rising cost of extracting metals from existing traditional deposits, increasingly stringent environmental regulations and a greater awareness of corporate social responsibility issues are all factors in stimulating the examination of mine tailings and small-scale alluvial deposits as a potential source of new raw materials. Furthermore, despite tougher economic times the demand for commodities remains strong, in no small part as a result of the growth of the world’s emerging economies.This combination of social and economic factors looks set to continue in the long term which will encourage greater recovery of materials from previously ignored sources such as mine tailings and ores from alluvial deposits.An expansion in the recovery of useful materials from mining-related activities is likely to require the use of robust and innovative techniques that have a built-in degree of future-proofing; DC plasma technology is one such technology.As a result of its ability to separate the valuable metal and minerals from the waste material while destroying hazardous compounds, Tetronics’ DC arc technology offers an alternative approach to resource recovery from a wide range of mine ores. Harmful cyanide compounds and the vast quantities of water used in conventional hydrometallurgical processing are avoided when plasma processing is adopted. DC arc technology also brings additional benefits, including: the extremely effective destruction of organic materials, the conversion of the inorganic material into a re-useable aggregate and the high tolerance of the process to fine and dusty materials. This paper presents details of Tetronics’ DC arc technology as one of the key pyro-metallurgical solutions available for the recovery of valuable materials from traditional mine ores and tailings, as well as giving specific examples of how the technology has been successfully employed in the recovery of enriched slags, ferroalloys and other metals."

Jan 1, 2016