Search Documents

By Y. Dong, L. Li, L. Yu

Converter slag has become an important secondary raw material. Consequently, vanadium bearing converter slag is of great interest for the recovery of vanadium. Solidified converter slags are made up of three main mineral components: dicalcium silicate, calcium ferrite and wustite. Vanadium in modified slow cooling down converter slag of Magang is found mainly concentrated in a separate mineral phase. The mineral phase with high content of vanadium (24%, wt, V205), concentrating 83% of vanadium, can be separated from the slag for economical vanadium recovery. Some characters of the mineral phase were discussed comparing with dicalcium silicate, one of the typical mineral phases in converter slag studied well.

Jan 1, 2004

By J. F. Wang, Y. Jin, Z. L. Wang

Smelting reduction as an ironmaking technology for the 21st century has been challenging the traditional blast furnace. The process has many attractive advantages over the blast furnace, however, the massive by-produced coal gas mainly containing CO, H2 and CO2 requires further treatment. From a chemical engineering view, coal gas is a valuable chemical stock and can be transformed into hydrogen-rich synthesis gas. Hydrogen can be directly used as clean fuel and synthesis gas can be used for the production of some important chemicals such as methanol, ammonia and dimethyl ether. Among those chemicals, dimethyl ether as an alternative clean fuel for diesel engine and liquefied petroleum gas has been drawing more attention. It has excellent environmentally-benign behaviours not only in compression ignition combustion, but also in the much lower emission of SOx and NOx. In this work, a combined technology of smelt reduction ironmaking and direct synthesis of dimethyl ether, which will strongly promote the energy efficiency, environmental protection and resource recovery, is proposed and described in detail.

Jan 1, 2004

By H. Hao

This paper outlines the development of a 2-D axisymmetric mathematical model to predict the evolution of temperature during the Direct Chill (DC) casting of AZ31 magnesium billets. Model predictions of temperature have been compared to measurements made on an industrial DC casting machine at Timminco Ltd, in Haley, Ontario. These measurements have been used to fine-tune the thermal boundary conditions employed in the mathematical model, The model, which is based on the commercial finite-element code ABAQUS, has been developed as part of a strategic project aimed at improving the DC casting process for light metals through a reduction in casting related defects and increased productivity.

Jan 1, 2004

By T. H. Etsell, P. C. Holloway

The fly ash produced by oil sands operations in northern Alberta represents a large, high-grade, potential resource for vanadium production in Canada. After extensive batch testing at the University of Alberta, a conceptual process flowsheet for the recovery of vanadium from oil sands fly ash has been developed. The various unit operations for this process, including decarbonization, roasting, leaching, desilication, precipitation, salt recovery and byproduct recovery, are described. Processes for the recovery of molybdenum and ammonium chloride from waste streams from this process, are proposed, as are potential uses for the ash residue; these byproducts represent significant potential sources of secondary revenue while reducing the environmental impact from the process. A preliminary economic analysis for vanadium recovery from oil sands fly ash using this process is also included and several major economic factors influencing its commercialization are discussed.

Jan 1, 2004

By S. W. Asihene, K. Osseo-Asare

The thermodynamic data necessary for the quantitative treatment of Metal-NH3- H2O systems at elevated temperatures are lacking in the literature. As a result discussions of the chemical basis of high temperature processes, such as leaching and hydrogen reduction, have tended to rely on low temperature thermodynamic data. In this paper a critical review is presented of the available high temperature data for metal ammine formation in aqueous systems, and methods are suggested to enable extrapolation of elevated temperature stability constants from low temperature thermodynamic data. Predictions of the Van't Hoff Lsobar, the simple cation Correspondence Principle (whereby metal ammine complexes are treated as simple cations) and Helgeson's Electrostatic-Nonelectrostatic Model are compared with the available high temperature stability constants for nickel ammines. Up to 80 °C all three estimation methods yield results which are in agreement with experimental data. However, serious deviations occur at higher temperatures; the various models overestimate the stability constants in the order Van't Hoff Isobar > electrostatic-nonelectrostatic model > simple cation Correspondence Principle. Using the experimental nickel data as a basis, a method is presented which permits reasonable estimates to be made of the stability constants of metal ammine complexes for temperatures above 80 °C.

Jan 1, 2004

By Michel R. Julien, Michel Lemieux, Jean Cayouette, Daniel Talbot

"The Louvicourt Mine located near Val d’Or, Quebec has been in operation since 1994. It produces copper and zinc concentrates. The tailings generated from the ore processing operations have a strong net acid generating potential. Louvicourt Mine, a grass root project, was designed for closure with the best available technology at the time of design. In order to inhibit short and long time acid potential generation, sub-aqueous disposal was selected at the design stage. Given the fact that disposal in a natural lake was ruled out up front for obvious reasons related to loss of natural habitat and risks of permitting delays, a man made facility built with dams was planned. This mine includes therefore the first fully man-made sub-aqueous tailings disposal facility built in Canada. The requirement of using sub-aqueous disposal had serious implications on the placement of tailings. This tailings facility located about 9 km from the mine site has been selected based on the available natural confinement, the favorable foundation and hydrogeological conditions. This paper describes the site and the design criteria that were used. A presentation is also made on the placement technique to maximize storage and its impact on the operation of the basin. The performance of the basin, the dams and the decant structures is reviewed.Résumé : La mine Louvicourt, située près de Val d’Or, Québec est opérationnelle depuis 1994. Elle produit des concentrés de cuivre et de zinc. Les résidus générés par les opérations de traitement du minerai possèdent un fort potentiel net de génération d’acide. Le parc à résidus de la mine Louvicourt, implanté dans un milieu naturel intact, fut doté dès sa conception initiale de la meilleure technologie de fermeture disponible à l’époque, soit la déposition sous couverture aqueuse et ce, dans le but de bloquer le potentiel de génération d’acide à court et à long terme des résidus. Etant donné que la déposition dans un lac naturel fut mise de côté dès le départ pour des raisons évidentes reliées à la perte d’habitats naturels et au risque d’introduire des délais dans l’émission des permis, un étang artificiel délimité par des digues a été conçu. Cette mine fut donc la première au Canada à être dotée d’une installation anthropique de disposition des résidus sous une pleine couverture aqueuse. L’exigence d’une déposition sous couverture aqueuse a eu des implications sur le mode de mise en place des résidus. L’emplacement de l’installation de gestion des résidus a été choisi en un lieu situé à environ 9 km du concentrateur sur la base du confinement naturel disponible et des conditions hydrogéologiques et géotechniques favorables. Cet article décrit le site et les critères de conception utilisés. Une présentation est faite sur la technique de mise en place utilisée pour maximiser l’entreposage et son impact sur l’opération du bassin. La performance du bassin, des digues et des structures de décantation est également revue."

Jan 1, 2004

By L. Bichler

Lightweight magnesium alloys are gaining in popularity for applications in the automotive and aerospace industries, Their use, however, remains limited due to their relatively low strength and creep properties. Lost Foam Casting (LFC) is a new casting process and the strength of foam cast magnesium alloys has not been investigated in great detail thus far, In this research, magnesium alloy AZ91 E and three new alloys were cast by the LFC process to study the effect of varying aluminum and manganese content on the alloy's tensile properties, The study reveals, that the tensile strength of the magnesium alloy is closely related to the relative amount of aluminum in the system. Formation of ß-Mg17Al12 phase was seen to significantly affect the yield strength and ductility of the alloy, Furthermore, formation of manganese intermetallic compounds was seen to effectively increase yield strength of the base alloy, Individual alloy morphologies were analyzed via optical and SEM techniques.

Jan 1, 2004

By B. Hewitt

Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedw ell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1% (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2% improvement in the circuit underflow density. The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil® dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary to solution neutralisation improvements.

Jan 1, 2004

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By Xiao Huang, Dongmei Wang, Prakash Patnaik

Further increase in gas turbine engine temperature necessitates continuous development and advancement to thermal barrier coatings. While tremendous effort has been devoted to developing new thermal barrier coating materials and processing methods in order to decrease the thermal conductivity, limited attention has been paid to radiative thermal transport through coatings. It is the purpose of this study to develop a new layered coating structure that can be used to effectively reduce the both radiative thermal transport as well as thermal conductivity, and to demonstrate the mechanism and effectiveness of the proposed multilayered structure. Mathematical modeling based on the multilayer quarterwave stack and simulation results are presented.

Jan 1, 2004

By Kousuke Takahata, Hirofumi Yoshimura, Jun Nakahigashi

Studies of a protium treatment for grain refinement of a + ß type titanium alloy are reviewed and recent experimental results are introduced. Protium treatment consists of the following three processes: (1) protium absorption, (2) martensitic transformation and hot working, and (3) final treatment for protium desorption and recrystallization. A combination of these processes results in the ultra-fine grains of 0.3 to 0.5 µm in diameter with high angle boundaries. The ultra-fine-grained material exhibits superplastic elongation of over 9000%. Superplastic forming was successfully used to fabricate a denture base. These materials may be widely applicable as biomaterials in various medical industries.

Jan 1, 2004

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By J. Day, Matthew X. Yao, Lijue Xue

Hardfacing overlays are commonly applied on the shroud Z-section of turbine blades for enhanced wear resistance. Among various processes that are used to apply the hardfacing overlays, the plasma transferred arc (PTA) welding process offers several advantages including lower heat input, less base material dilution, rapid process time, and reduced operating cost associated with the capability to apply materials in the powder form. The development of a robust PTA process is crucial for overlay performance and repeatability, particularly in the aerospace industry where a quality intensive manufacturing environment prevails. For this reason, the Taguchi method of experimental design was selected to develop a test plan. A 4-factor 3-level (L9) orthogonal array (OA) was used in the experiment. The L9 OA allows for a more detailed (3 level) investigation of critical process parameters, namely plasma gas flow rate, traverse speed, powder feed rate, and arc current. Two hardfacing materials, Stellite 694 and Tribaloy T-800, both Co-based wear resistant alloys, were investigated by deposition onto a cast IN738 Ni-based superalloy substrate. Performance measurements of the hardfacing deposits included deposit hardness, substrate hardness, deposit density (porosity), degree of cracking/inclusions, and a quantified visual inspection. The procedure resulted in optimized PTA hardfacing parameters for both Stellite 694 and Tribaloy T-800 on IN738 turbine blade material.

Jan 1, 2004

By Ron Millions, J. A. Folinsbee, Ishwinder Grewal, Michael Fullam, Don Strickland, Tony Y. Chong

"Since milling began in 1912, the Dome mill, now part of the Porcupine Joint Venture (PJV), has been expanded several times, the most recent increasing the milling rate from 3,500 to 11,500 tonnes per day. Dome uses conventional crushing and grinding followed by gravity concentration to recover free milling gold. A cyanidation/CIP process recovers the remaining gold in the gravity tails.Over the past few years, continuous gravity improvements have increased the gravity recovery from 20% to nearly 50% of the plant feed gold. This paper describes some of the factors that have contributed to this dramatic increase, and suggests how gravity recovery can be further improved. Gravity circuit availability has been improved to >98% with the implementation of a preventative maintenance program. More Knelson concentrators have been added to the circuit, and in 2002, an Acacia Intensive Leach Reactor was installed to replace the shaking table. In 2003, the entire gravity circuit was audited to evaluate and quantify the circuit performance. The metallurgical and mechanical operating conditions of the gravity circuit are now well understood, and areas for further improvement are well defined.INTRODUCTIONThe Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. One of the goals of the JV was to use the milling capacity of the Dome mill to process ore from Placer Dome and Kinross mines in the Timmins Camp. The PJV Dome Mill utilizes gravity concentration, cyanide leaching and carbon in pulp gold circuits to recover gold. Gravity recovery has been used in some form at the Dome Mill for most of its existence, first using conventional jigs, these being replaced in 1993 by two Knelson Concentrators, one for each of the two grinding circuits in the Dome mill. Over the years more concentrators have been added to improve the gravity recovery, most recently in 2002 for a current total of five. Also in 2002, an Acacia Intensive Leach Reactor was added to process the Knelson concentrate, replacing the shaking table."

Jan 1, 2004

By W. Wallace

The aerospace industry celebrated 100 years of powered flight in 2003, and the remarkable achievements that have occurred during the past 100 years are in no small way due to major developments in materials. Modern alloys for airframes, engines and other major sub-systems have evolved through the intelligent application of new processing concepts involving melting, casting, hot and cold working, heat treatment and more recently vapour phase processing. Alloy design has evolved in parallel to allow maximum benefits to be achieved from these processing advances. However, the pace of development seems to be slowing and future gains are likely to be made by learning how to extract major value from aerospace assets. Understanding the modes of deterioration and establishing cost effective lifetimes by holistic life cycle management seem to be the way of the future. Extending component lifetimes by repair, rejuvenation and refurbishment are all viable possibilities and they offer great opportunities for Canada, which, traditionally, has been a major user of modern aerospace materials rather than a supplier. The challenges for metallurgist, physicists and engineers will be no less than in the past and should create new business opportunities for Canada. The scenario described above will be developed by calling upon examples drawn from the author's experience.

Jan 1, 2004

By Edgar Dernedde

Cryolitic melts at a temperature of about 960 °C are used in reduction cells to dissolve alumina and to produce primary aluminium. At these temperatures cryolitic melts with an acidic composition have a significant vapour pressure, which contributes substantially to the evolution of fluorides from these cells, The Antoine equation is commonly used for relating vapour pressure data of liquids at different temperatures, It is also applicable to cryolitic melts, Published equations have at least 20 numerical constants, in order to allow for the effects of melt composition. In the present work a simplified equation with only 12 numerical constants was developed and is applicable for multiple additions to molten cryolite up to 30 wt %, The simplified equation was compared with the published equations of Haupin & Kvande and Gustaysen & Ostvold using 472 vapour pressure data of cryolitic melts. Results showed that the simplified equation has the same accuracy as the published equations in the composition range of interest to industry.

Jan 1, 2004

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By K. Fujita, T. Kikuchi, Y. Sakamoto

Ceramic fibers were classified as a category 2 carcinogen by The European U legislation. Therefore we developed non-fibrous insulating castable which utilizes n porous aggregate, which is composed of Calciumhexaluminate. Although at beginning we applied alumina cement as binder for non-fibrous insulating castable, kind of formulation had a poor resistance to spalling. We developed non-fibrous insulating castable without alumina cement. This solved a problem which pre\ formulation had a poor resistance of spalling. We applied a new non-fibrous insub castable for reheat furnace in steelworks, then we could achieve good result which condition equivalent to ceramic fiber insulating castable.

Jan 1, 2004

By M. Reza Bateni, M. Zandrahimi, J. A. Szpunar

Titanium aluminides and nickel aluminides offer the potentials, as coating materials, for high temperature and aerospace applications. In this research, attempt has been made to develop Al-Ti and Ni-Al intermetallic compound coatings on the surface of Inconel 738. The coatings applied through pack cementation and simultaneous diffusion annealing processes. Scanning-electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDAX) and grazing angle X-ray diffraction were used for evaluating of coating structure. It was demonstrated that the pack cementation technique could be used to develop TiAl3 and AlNi intermetallic compounds coating on Inconel 738 substrate. When pack cementation technique is based on a halide-activated pack with aluminum and titanium powders, the coating consists of TiAl3 intermetallic compound phase. Whereas, by pack aluminization of Inconel 738, the coating consists of AlNi intermetallic compound phase.

Jan 1, 2004

By Andrea R. Gerson, Roger St. C. Smart, Russell Schumann, Joan E. Thomas, Warwick Stewart, Stuart Miller

Sequential Net Acid Generation (NAG) accelerated oxidation testing using peroxide was carried out on single sulfide mineral samples. The calculation of the nett acid production potential (NAPP) assumes that all the sulfide is present as pyrite and that dissolution results in a 2:1 ratio of H+:SO42-. NAPP as kg H2SO4/t is calculated as 30.6 x wt.% S present. To test whether this calculation is valid a NAPP* value was defined in which instead of using the wt.% S present for the calculation the wt.% S dissolved is used. Stoichiometric analysis of the dissolution products of the sulfide minerals as they would occur at pH 7 indicates, that in all cases, the ratio of H+:SO42- of 2:1 is viable. The NAG to pH 7 and NAPP* closely coincided for pyrite, bornite, chalcocite and covellite. For the three Cu-containing minerals, the NAG to pH 4.5 value was 0 as is predicted on the basis of the speciation likely to be present at pH 4.5. Acid generation is due to hydroxylation of the dissolved Cu between pH 4.5 and 7.0. The NAG to pH 7 and NAPP* values for chalcopyrite, arsenopyrite and pyrrhotite were in reasonable agreement but were not for either sphalerite or galena. Zn is not completely hydroxylated at pH 7 as is assumed by the calculation. For galena, surface analysis identified polysulfide formation on of the leach residue polysulfide. The formation of polysulfide is an acid consuming reaction. Therefore under conditions of accelerated oxidation the NAPP value is a reasonable estimate of the possible acid production in all cases except for sphalerite and galena. However, under conditions of less intense oxidation, for instance in columns, waste rock and tailings dumps, the formation of polysulfides is likely to be more widespread thus reducing the correlation between NAPP and the maximum possible acid production.

Jan 1, 2004