Search Documents

By J. W. Matousek

"More copper concentrates are treated in flash smelting furnaces than by any other process, and such furnaces are located in most of the world's major copper producing areas. Except for perhaps two furnaces treating chalcocite-type materials, little difference is seen between the grades of the concentrates being smelted. Within individual smelters, even less variation in feed grades is found. This is both accidental and intended. Many furnaces treat concentrates from captive ores, and these tend to be of relatively constant composition over long periods. Toll smelting operations blend concentrates to ensure delivery of feeds of fixed compositions to their furnaces to avoid upset conditions. Matte grades vary between flash smelting furnaces, but most commonly, these are the result of differences in operating practices rather than because of differences in concentrate grades. This paper reviews an industrial flash smelting test in which the copper content of the furnace feed was intentionally altered over a wide range. IntroductionExcept in a few copper mining regions of the world, the principal copper mineral is chalcopyrite (CuFeSz). This results in the almost universal production of concentrates containing 25070 to 30% copper (and similar amounts of iron and sulphur). Many operators of copper flash furnaces spend their entire metallurgical careers smelting concentrates of essentially fixed grades. This is true both of smelters treating concentrates from captive mines and those processing concentrates on a toll basis. From the production staff's point-of-view, the less variation in grades seen by the furnace, the better. Fixed analyses of concentrates and constant feed rates produce consistent quantities of matte at a consistent grade for processing by the converters. The result is, even in smelters treating a variety of concentrates, efforts are expended in sampling and blending to ensure feeds of relatively uniform compositions being sent to the furnaces."

Jan 1, 1993

By Kevin Azocar, Jim Hazzard

"Slope stability analysis is performed most commonly using limit equilibrium calculations or numerical models assuming a two-dimensional slice through an infinitely long slope surface. In areas such as open pit mining, where most slope surfaces are not planar, the importance of curvature becomes important due to the economic gains associated with creating a steeper slope. With advances in computing capabilities within the last decade, three-dimensional slope analysis can be performed within reasonable time frames. Some work has been done on the potential importance of curvature on slope stability, mainly assuming homogenous materials with a circular shear-failure mechanism. However, many open pit mines are excavated in jointed rock mass where a completely different set of failure mechanisms can be seen. Depending on the geometry and radius of the pit, the curved geometry may influence the factor of safety and failure behaviour compared to a two-dimensional slice.A series of numerical analyses were performed to investigate the effect of curvature on jointed rock slope stability compared to an equivalent two-dimensional slope analysis. By using discrete element method models, the influence of joint planes and interaction between distinct blocks can be seen. With a three-dimensional model, the effect of curvature can be combined with multiple joint sets at any orientation, which cannot be seen in a single slice. Numerous three-dimensional models are created, along with an equivalent unit-thick slice. The effect of curvature on a variety of different types of failure mechanisms is observed, and graphical relationships are created to quantify the difference between the three-dimensional factor of safety and the two-dimensional factor of safety based on the degree of curvature."

Jan 1, 2015

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

By Grant Small, Jessica Kinal, Christopher J. Greet

"The conversion from an electrochemically reactive grinding media (forged steel) to a more electrochemically inert alloy (high chrome white iron) not only reduces the wear rate of the grinding media, but also has an impact on the grinding chemistry. Typically the grinding chemistry becomes more oxidising, with less reducing Eh values and more dissolved oxygen in the pulp. There is also a decrease in the EDTA extractable iron, which is an indication of the change in the media corrosion. These changes are indicative of alterations in the surface chemistry of the minerals that the operator is trying to separate. For porphyry copper ores the changes in the pulp and surface chemistry not only affect the copper sulphide minerals, but also impact the iron sulphides (i.e. pyrite and pyrrhotite). Generally, with more oxidising pulp chemical conditions during grinding there is an increase in the oxidation of the iron sulphides which renders their surfaces hydrophilic, thereby depressing flotation. This leads to improved selectivity for copper sulphides against iron sulphides.INTRODUCTIONPorphyry copper deposits are the dominant source of copper that is mined today to satisfy global demand. These style of deposits typically contain one percent copper mostly as chalcopyrite, but may contain other copper bearing minerals (for example, bornite, chalcocite, azurite, malachite), small quantities of pyrite and quartz. Porphyry copper deposits also contain economically significant quantities of gold, silver and molybdenum. Interestingly, the majority of the world’s porphyry copper deposits are concentrated along tectonic plate boundaries (Figure 1)."

Jan 1, 2016

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By Mei-Yan Yang, Qiu-Ying Wang, Ltd. Yunnan Yuntong Zinc Co., Guo-Mu Chen, Meng-Yang Huang, Peng Zeng, Guo-Feng Li

"Historically, alot of jarosite was found in the leaching residue when leaching indium from secondary zinc oxide materials. The reasons for the formation of indium bearing jarosite were theoretically analyzed. The influence of controlling the acidity and the addition of reagents on the indium leaching yield during secondary zinc oxide processing was investigated. In order to increase the leaching yield of indium, a measure of controlling the creation and destruction of jarosite was proposed. The production data shows that the leaching yield of indium was increased from 60 to 96%, and the content of indium in leaching residue simultaneously decreased from 900g/t to 100–200g/t when implementing such controlling measures.INTRODUCTIONIndium does not occur as independent minerals in the earth’s crust and is mainly associated with complex sulphide minerals. Specifically some sphalerites can contain as much as 900g/t of indium. Most indium is recovered from by-products of copper, lead or zinc metallurgy. Therefore, the research on the recovery of by-products in non-ferrous metallurgy is important(Sinclair et al, 2006). The main technologies used for this objective in China include: •,pre-neutralization-reduction-precipitation indium process(Yu et al, 2008), •,countercurrent oxidizing acid leaching process and sulphation roasting-water leaching process(Cao, 2005), •,oxygen pressure acid leaching of zinc concentrate-P204 extraction process(Yang et al, 2006), •,doubleacid leaching-solvent extraction process on lead dross from a reverbatory furnace flue dust(Liu, 2003),•,an acid leaching-solvent extraction process on smelting ash(Zhouet al, 2005). Although high pressure and extreme conditions can be used to improve extraction from high iron bearing indium residues(autoclave processing), mild extraction with lower cost and lower environmental impact are preferred.This paper describes both how the indium extraction using mild conditions in a secondary zinc circuit was quite low and, how through XRD and chemical analysis jarosite formation was found as the main cause. The paper then proceeds to discuss a method for improving the leaching yield and the application of this method in industrial practice."

Jan 1, 2016

By A. G. Spencer, A. D. Taylor

This paper discusses some of the advantages and problems associated with the selection of large unit equipment for a metallurgical plant. A given flowsheet and material balance for an iron ore concentrator is assumed. Then two plant designs are developed, one utilizing a number of smaller-size equipment units and one utilizing the largest available equipment units. The mechanical and electrical problems are discussed and a comparison of capital costs is made. Finally, brief consideration is given to a plant de-sign using units larger than those which are currently available.

Jan 1, 1968

By S. Perez

Core drilling is a fundamental process in the mineral exploration industry. As deep exploration in hard rocks is accelerated due to the depletion of near ground mineral resources, deep-drilling operations need to reduce their reliance in operators experience and begin to implement new technologies in order to increase efficiency and cost-effectiveness of the overall process. Currently, lack of real-time information on the bit/rock interaction is a major problem. Therefore the mechanism behind the acoustic emission, which is a proven technique for remote monitoring, generation in mechanical rock cutting must be understood in order to provide real time information about the rock. This paper aims to identify the influence of mineral composition of granitic rocks on the acoustic emission (AE) during rock abrasivity test with a single contact tool and to evaluate the feasibility of AE as a means to infer Cerchar Abrasivity Index (CAI). Single contact tool will provide precise and accurate description of the source of AE. To provide constant grooving speed Cerchar apparatus was modified to monitor AE during rock/tool interaction. Tests on the modified Cerchar apparatus are carried out under the static load of 70N and cutting speed of 1 mm/s. A Scanning Electron Microscope (SEM) is utilized to visualize the groove in the rock and to identify the mineral composition through Back-Scattered Electrons (BSE) reflected from the rock sample. Based on the microscope images, it was found that biotite shows a larger groove area and plate-like fractures accompanied with burst-type AE signal, whereas plagioclase and quartz, which are characterized by similar hardness and BSE brightness, possess shattered-like fractures and more continuous-type AE signals. In addition, a-value of the Gutenberg-Richter scale has been found to well correlate with Cerchar Abrasivity Index (CAI).

Jan 1, 2015

By Charles Camsell

Few persons ever stop to consider how vital an influence minerals, and especially metals, have had upon human history, how they have affected the every-day life of the individual or how at different periods they have altered the course of nations and determined their progress. Students and writers of history have dealt very fully with political history and have given us a great deal of detail about the careers and policies of kings, parliaments and nations, but frequently have not touched the economic causes that have been the real forces influencing the development and carrying out of these policies. So far as minerals are concerned there is no single work from which one can get a concise and consecutive account of the growth in the use of minerals, nor of the diverse ways in which the. geographical distribution, the .search for, the development and the use of mineral resources have affected human progress from the beginning of man's history. The reason for this is quite plain, and when one takes a little time to think of it he begins to appreciate the magnitude of the job and he will realize that the story of minerals and mineral resources touches a tremendous range of human activity, not only of mining .and metallurgy, but the whole field of agricultural and industrial growth, of exploration and colonization, transportation and commerce, monetary system, commercial policy, in short, almost every phase of economic life.

Jan 1, 1926

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By W. T. Thompson, S. Durham, K. M. Jaansalu

The role of platinum on the relative stability of gamma - gamma prime equilibrium is only qualitatively known, and may bear upon the stability of a superalloy under a protective coating. The binary phase diagrams Ni-Pt and Al-Pt, and the Ni-rich corner of the Ni-Al-Pt ternary, are reviewed and simple self-consistent thermodynamic models are derived. These thermodynamic models are incorporated into a database used to predict the gamma-gamma prime equilibrium for single crystal superalloys. In small concentrations, platinum is predicted to increase the temperature stability, but not the proportion, of the gamma prime phase over the gamma phase in third generation alloys such as CMSX-10. Another effect of platinum addition is to significantly lower the solidus temperature. These findings are compared to experimental data in the literature.

Jan 1, 2004

By R. A. L. Drew, J. P. Immarigeon, F. Jalilian, M. Jahazi

In the present work TLP bonding of Inconel 617 is investigated. The influence of the main processing parameters i.e. time and thickness of the interlayer were studied with optical and scanning electron microscopy. Boron containing interlayers with two different thicknesses were used and the influence of various holding times from 5 min to 24 hours on the microstructure of the bond region was investigated. The results indicated that, for the testing temperature of 1065°C and holding times above 2 hours with an interlayer of 25.4 microns thick no liquid phase was observed. The same phenomenon occurred only after 6 hours for a 76.2 microns thick interlayer. Precipitate growth started at grain boundaries and continued inside the grains. The composition, size and morphology of the precipitates were studied using electron microprobe analysis. No noticeable changes were observed in the grain size of the base metal with increasing holding times.

Jan 1, 2004

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By R. Carter, C. S. Samis

"SummaryThe results of this investigation indicate that the gold in the cyanide tailing of refractory gold cyanides is occluded in fused •particles formed during roasting. This conclusion was reached following microscopic examination of calcines produced at various furnace temperatures with different atmospheres, and a •comparison with calcines produced by decomposing samples of completely sulphated concentrate under conditions such that the maximum particle temperature varied between 6•50°C. and 1,100°C. This comparison showed that the particle temperature during a normal roast may be several hundred degrees higher than the furnace atmosphere, or that the fusion is associated with a low melting (950°C.) eutectic mixture of FeO and FeS.Because of the unavoidable particle fusion during a furnace roast, and because low particle temperatures are essential for gold extraction by cyanidation, aqueous medium oxidation under high oxygen pressures was studied. Gold recovery from calcines produced by this means was over 98 •per cent •compared with a maximum of 80 per cent from furnace calcines.IntroductionMANY arsenical gold ores are called 'refractory' because much ' of the gold cannot be satisfactorily extracted by cyaniding the raw ore or concentrate. Even when such ores are roasted to oxidize .the iron and arsenic and 'release' the gold, often 10 to 25 per cent of the gold present is lost in the cyanide residues."

Jan 1, 1952

"Shales play a major role in the stability of slopes, both natural and engineered. This paper attempts to provide a review of the state-of-the-art in shale slope stability. The complexities of shale terminology and classification are first reviewed followed by a brief discussion of the important physical and mechanical properties of relevance to shale slope stability. The varied mechanisms of shale slope stability are outlined and their importance highlighted by reference to international shale slope failures. Stability analysis and modelling of anisotropic rock slope masses are briefly discussed and the potential role of brittle rock fracture and damage highlighted. A short review of shale slopes in open pits is presented.INTRODUCTIONShales have been stated to form approximately 58% of sedimentary rock so it is not surprising that they are frequently encountered in both natural and engineered slopes. They represent challenging environments for slope stability due to the wide variation in their engineering properties, their changing behaviour with time due to geomorphic processes and the variation in the failure mechanisms as a function of both stratigraphy and tectonics. An extensive body of literature exists on the terminology and classification relevant to shales; it is not possible in the scope and length of the current paper to review these works in detail and the reader is referred to Farrokhrouz and Asef (2013), Bell (2000) and Goodman (1993) for detailed discussions. It is arguably the case that no universally accepted classification of shales exists today and depending on the field of application the terminology varies widely. Shales in slope stability, for the purpose of this keynote paper, are taken to include material varying in properties from weak rocks to soils and therein lies one of the most challenging aspects in shale slope characterisation for engineering purposes. They have been classified as “rock-like” or “soil-like’, (Underwood 1967) or compacted and cemented, Table 1, Yagiz (2001). Classifications have considered numerous factors including composition, cementation and a wide range of engineering properties.The propensity of shales to degrade with time due to geomorphic processes has resulted in an important aspect in their classification, that is, the attempts to incorporate slaking, durability and swelling and softening behavior through purpose developed testing methods (Gamble 1971, Morgenstern and Eigenbrod, 1974). Figures 1 and 2 show examples of terminology used to describe argillaceous materials and some proposed engineering classification schemes (Grainger 1984 and Bott 1986). Corominas (2014) provides a recent classification of argillaceous rocks and their durability relating five stages of slope deterioration to the texture of the rock on Ternary diagrams. No attempt will be made here to discuss the merits of the proposed terminology and classifications, suffice it to say, that the controversy and flux surrounding these issues is a strong indicator of the complexities in the behavior of these materials. In this paper the author will consider slope stability in the materials indicated in Table 1, Figures 1 and 2 without undue focus on terminology. At the lower strength limit of shales the engineer must design slopes using the principles of soil mechanics which may vary from the simple Mohr Coulomb plasticity constitutive criterion to modified critical state models, some even attempting to incorporate softening behaviour in the weaker clay shale materials. Given the transitional nature of shale materials several workers have treated overconsolidated clays and clay shales using concepts such as peak and residual shear strength, brittleness index and softening. Martin and Stacey (2013) provide a useful review of the importance of weak rocks in open pit mining, with mudrocks as a specific member, and note the importance of delayed failure, progressive failure and loosening in the stability of"

Jan 1, 2015

By S. F. Guo, B. W. Zheng, X. L. Huang, S. W. Qi

"The study of mechanical characteristics of rock discontinuities under different shear deformation velocities is an important premise of rock slope dynamic response analysis. According to disposing and calculating the experimental results of previous research about peak shear strength of rock discontinuities under different shear deformation velocity of constant normal loading, the law of influence of shear velocity on the total friction angle is studied. Based on the research results, it can be found that the total friction angle of rock joint specimens varies in the form of negative logarithm with the variation of shear deformation velocity. It’s also indicated that the total friction angle of rock joints decreases with the increase of shear deformation velocity for rock joints of relative strong homogeneity and isotropy. However, the total friction angle of rock joints increases with the increase of shear deformation velocity for rock joints of relative strong heterogeneity and anisotropy and the latter amplitude of increase is less than the former amplitude of decrease. The physical property and microscopic geometry of rock joints play an important effect on the increase or decrease tendency and amplitude variation of total friction angle with the increase of shear deformation velocity.INTRODUCTIONThe rock slope dynamic response is largely restricted by rock discontinuities. Hence the study of dynamic characteristics of rock discontinuities, especially the dynamic shear characteristics is an important premise of rock slope dynamic response analysis (Qi et al., 2007). Seismic load is both dynamic load and cyclic load (Liu et al., 2011). Under the dynamic and cyclic shearing actions of seismic load, the rock slope which is stable under the condition of static load may slide along the rock discontinuities whose shear strength reduce and then the earthquake landslides occur. The strength degradation and deformation mechanism of rock discontinuities under the dynamic and cyclic shearing actions is one of the key problems to be solved in the work of earthquake prevention and control of engineering slope. Based on the above understanding, predecessors conduct some researches which focus on the shear behavior mechanical characteristics of rock joints under cyclic shearing actions (Plesha, 1987; Hutson & Dowding, 1990; Jing et al., 1992, 1993; Huang et al., 1993; Qiu et al., 1993; Homand et al., 2001; Lee et al., 2001; Jafari et al., 2003; Liu et al., 2011, 2013). However, there are a few researches about the mechanical characteristics of rock joints under different shear deformation velocities because of the restriction of shear apparatus. Crawford and Curran (1981) conducted a series of one-way cyclic direct shear tests on four kinds of natural rock joints under different shear deformation velocities varying from 0 to 200 mm/s. The tests showed that at low normal stresses the peak shear strength of soft rock joints exhibited an increase up to a certain velocity, after which it remained essentially constant. For rock joints of intermediate hardness, the peak shear strength was essentially independent of shear deformation velocity; whereas for hard rock joints, the peak shear strength of which showed a significant variation with the shear deformation velocity. Jafari et al. (2003) carried out a series of conventional triaxial tests on artificial rock joints of regular saw-tooth shape with axial loading rate from 0.05 mm/s to 0.4 mm/s."

Jan 1, 2015

By H. Wotruba, J. Heizmann

"The use of shotcrete is a mandatory means for rock support and therefore for safety in many underground mining operations. If shotcrete gets into the flotation feed though, it can negatively influence the flotation process. This especially occurs when sublevel stoping, cut-and-fill or room-and-pillar methods are applied because as the mining face moves on, formerly applied shotcrete layers are mined together with the ore.As shotcrete does not differ significantly from fluorspar ore in its physical properties it gets moved through the comminution process and is fed to the flotation plant like the ore. To prove the influence of shotcrete on the flotation process, a laboratory test series was conducted at the Unit of Mineral Processing (AMR) of the RWTH Aachen University. The shotcrete grade of the flotation feed was varied between 0 and 10% through addition of pure shotcrete. Flotation parameters and also reagent dosage were held constant apart from the addition of the pH regulator, which was dosed to reach a constant pH of 8 at the flotation start. Results showed that with increasing shotcrete grades in the flotation feed the fluorspar recovery as well as general mass recovery decreased. The enrichment factor of Fluorspar also decreased with increasing shotcrete grades in the feed.In an effort to eliminate the shotcrete contamination of the flotation feed, a feasibility study for use of sensor-based sorting prior to the comminution process was conducted. Rock sorting not only reduces the bad influence of shotcrete on the flotation process, but also reduces comminution costs. INTRODUCTIONShotcrete is used in underground mining on a regular basis. It is used for rock support and therefore to increase safety in the underground mining environment. In mineral processing the presence of shotcrete can cause difficulties for example in the concentration processes. In flotation the highly sensitive reagent mixtures can be disturbed by the chemical activity of shotcrete and therefore recovery rates and selectivity of the process can suffer.Shotcrete is a special form of concrete which is applied pneumatically with high velocities and is compressed by its impact energy. Since the process is especially suitable for work in difficult environments and overhead areas, it is established in underground mining for many years. Shotcrete is not only applied in pre-processing of the mines, but particularly of use for cut and fill, as well as room and pillar mining methods. There it is used to secure excavation chambers. When the mine face is secured with shotcrete and subsequently the mining continues, the applied shotcrete will automatically be mixed with the ore."

Jan 1, 2016

By Leiting Yue, Peng Ren, Yu Shen, Zhihong Liu, Haibao Shao, Longgong Xia, Feng Yu

The Kennecott-Outotec Flash Converting technology has been proven as an advanced and mature process in 5 individual plants during the past 2 decades. High grade copper matte (65–72%) produced in the flash smelting, or other smelting technologies is granulated to 3-5mm granules in a water torrent, and further crushed to fine powder (≈50µm) and dried to contain less than 0.3% H2O. Oxygen enriched air, together with fine copper matte powder and lime flux are injected into the reaction shaft by a matte burner. The copper making and slag making reactions will happen in very short time and distance during the particle falling and settling. However, industrial practice has found negative effects caused by sodium contamination. Na is introduced in the copper matte granulating process, and appears as Na2SO4 on particle surface. When Na content was high, scaling problems in the boiler will be worse, and the processing air will be blocked by the growing accretion around the matte burner, and as-produced blister copper is always high in S and O. In this present study, an industrial matte sample was used in the experimental work. Na was introduced into the matte powder by Na2SO4 solution soaking. The burning behaviour of the doped copper matte powder has been investigated as a function of the impurity concentration and processing temperature. Morphology and composition of these samples explained how Na2SO4 converts and reacts in the oxidizing atmosphere, and how they or their converting species influence the burning behaviour of matte particles. Cross-sections of as-prepared samples were analyzed with SEM-EDS, and the reaction mechanism has been carefully interpreted. Results from the present study can benefit both academic and industrial people. INTRODUCTION "Flash Converting" technology was developed jointly by Kennecott Utah Copper Smelter and Outotec (Finland) OY in 1992. The first industrialization of the technology was in Utah Smelter in 1995. Since 2006, it has been successfully applied in Xiangguang Copper, Tongling Jinguan Copper Branch, Fangchengang Jinchuan Copper, and Ningde Southeast Copper. The technology has also been further developed in those smelters. At present, roughly 2 million tons blister copper is produced annually through the Kennecott-Outotec Flash Converting technology, accounting for more than 10% of global primary copper production. The technology has advantages of high efficiency, high sulfur capture rate, good in environmental issues, mature equipment supporting, high automatic control level, low comprehensive energy consumption and flexible connection with the smelting unit, which make the technology to be one of the best choices in investing a new large-scale copper smelter or updating an old copper project in the world.

Jan 1, 2019

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006