Search Documents

By K Luthbom, A Lagerkvist

According to the Swedish Environmental Protection Agency, the number of potentially contaminated sites in Sweden is approximately 40 000. The funding for remediation from the Swedish Government alone amounts to $A 60 - 80 M (300 - 400 MSEK) annually for the period 2003 - 2006. Uncertainties will arise when obtaining samples in field, preparing them in laboratories and analysing them. Different procedures give rise to varying errors. Using data for decision-making that does not truly represent the site could be fatal. Misclassification of soil could lead to unnecessary costs or to risks to human health and the environment. The total uncertainty of an environmental sample can be split into analytical uncertainty and sampling uncertainty. The analytical uncertainty is usually known and reported from routine analysis. The size of the sampling uncertainty is less well known. Hence, the question is how big are the sampling uncertainties for contaminated soil and how big is the analytical error compared to the total sampling error? A scrap yard and two landfills within a workshop area were investigated. An excavator dug trial pits and samples were taken with a trowel from the walls of the trial pits. Samples were put into plastic bags and taken off site for preparation and analysis using XRF. Sample preparation included drying and sieving. The samples were homogenised by kneading the sample bags prior to analysis. The sampling and sample handling were performed in an intuitively way without knowledge of sampling theory. However, Pierre GyÆs sampling theory was used for subsequent evaluation of the data from the site investigation. The theory defines seven sampling errors, which can be applied to sampling of soil. Some errors have a variance that can be calculated or at least estimated, while other errors can give some idea whether the bias is positive or negative. The total sampling error varied over three orders of magnitudes from sample to sample. The single largest contributor to the large variation in error was the contaminant level. When comparing the analytical error and the total sampling error the ratio varies more than three orders of magnitude.

Jan 1, 2005

In the hard rocks of the Nordic countries of Norway, Sweden and Finland underground works have a long tradition. Today the subsurface has been taken into use for a wide variety of purposes. In this paper only the more uncon- ventional examples are described such as caverns for drinking water, sand bunkers, molasses silos, wine and liquor stores, cold stores, heat storage, waste disposal and state archives. The particular use of unlined high pressure tunnels and socalled air-cushions for hydropower schemes is discussed. The dual use of subsurface air-raid shelters for sports activities seems to be a special Nordic tradition. Some cost figures are given and the advantages of using the underground is Discussed.

Jan 1, 1987

In July 1994 the Premier, John Fahey MP, announced that the New South Wales Government would make available a total of $40 million over six years in new funding for the Department of Mineral Resources. These funds are to be applied directly to the generation of regional geological and geophysical information. The Government's initiative known as `Discovery 2000', is aimed at providing a major boost to the exploration industry. The Government expects new discoveries to be made and new mines to be developed because of the initiative and, perhaps, the first ever commercial oil or gas production in New South Wales. The Government's return will come from increased economic activity, and from the increased royalty return from higher levels of production. Quality information is the key to successful exploration. In the highly competitive business of mineral and petroleum exploration high quality regional geological and geophysical information improve both the efficiency and effectiveness of the area selection or project generation process. Using the `needle in the hay stack' analogy, Discovery 2000 will vastly improve industry's chances of finding the haystacks. It is up to the mineral and petroleum industries to find their respective `needles'. Careful target area selection is probably the most critical factor in mineral exploration. The ability to select the most prospective areas, or to identify prospectivity that others have failed to recognise, can make all the difference between success and failure. Government geological surveys clearly have a crucial role to play in providing the geoscientific information infrastructure that companies must have if they are to make the discoveries this country needs to pay its way in the world. It is the regional information generated by Governments that sets the scene for efficient exploration. This regional information includes regional aeromagnetics and radiometrics and gravity, regional geological mapping and tectonic analysis, and geoscientific databases. The New South Wales Department of Mineral Resources (by various names) has been providing such information for over 100 years and has led the way in many aspects of the generation and dissemination of geological, geophysical and metallogenic Information.

Jan 1, 1995

By B Mobilio, M Secheny, J Rachocki, G B. Sharrock, A Jäger, J L. Lett, I Brunton, G W. Capes

Establishment of the Cadia East Panel Cave Stage One (PC1S1) commenced with the firing of the first bell in early 2011. Production began with the completion of the undercut in May 2014. PC1S1 used a post-undercut composed of 114 drawbells covering a footprint area of 73 438 m². The extraction level is located at a depth of 1200 m below the surface and is based on a 32 × 20 m El Teniente layout. Cave establishment required the construction of multiple conveyor drifts, a large-capacity jaw-gyratory crusher and ancillary ventilation and pumping infrastructure. Preconditioning via hydraulic fracturing and blasting was implemented at various locations of the cave block height. This paper presents an overview of the key learnings from the commencement of undercutting to surface breakthrough, including rock mass classification and modelling, stress measurements, preconditioning, numerical modelling and cave monitoring.CITATION:Lett, J L, Brunton, I, Capes, G W, Jäger, A, Mobilio, B, Rachocki, J, Sharrock, G B and Secheny, M, 2016. Undercutting to surface breakthrough – Cadia East panel cave (stage 1), in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 65–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Three separate and unconfined aquifers occur in the Hilton area, named relative to position in relation to ore horizons: Footwall Aquifer in the east; Ore-Zone Aquifer within the ore-bearing Urquhart Shales; and the Hangingwall Aquifer in the west.It is the on-going strategy it Hilton to drain the Ore-Zone Aquifer which occupies structurally- and sulphide-controlled leached zones in the steeply west dipping strata. The aquifer affects considerable ore reserves to 480 m below the surface. Dewatering began in 1976, and is essentially completed to 4 level (240 m below surface). Dewatering efforts are now based on 8 level (480 m below surface).

Jan 1, 1993

By S Viviers, G Ratner

Ventilation is part of all underground mine operations and is undertaken in order to introduce fresh, cool air to the workings and to remove stale, affected air. It is problematic to obtain efficient and accurate estimates of volume flow and static pressure in the installed operational configuration for the auxiliary axial flow fans.An empirical method was developed to estimate the static pressure and volume flow through a calibrated differential pressure port on axial flow fans. Prior to shipping, each fan is performance tested according to BS 848 (ISO 5801) to establish the fan performance curves. In addition to the standard required parameters captured to fully describe the performance, the differential pressure is measured across the fan rotor to enable correlation with the characteristic fan curve.The method was implemented on a ruggedised tablet PC platform. This compact platform is then used to calculate the volume flow rate from the differential pressure sensor measurement input via a USB port. The result is a real-time measurement of volume flow and operating point of the fan system. This can be used effectively in overall modelling of the mine auxiliary ventilation systems and calculation of system resistance could provide a health indication of the fan and duct system.CITATION:Ratner, G and Viviers, S, 2013. Underground auxiliary ventilation monitoring and diagnostic system, in Proceedings The Australian Mine Ventilation Conference , pp 57-62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The Callie Underground Mine is located in the Tanami Desert 560 km Northwest of Alice Springs in the Northern Territory and is currently operated by Newmont Australia Limited with all mining activities carried out by Henry Walker Eltin. Callie was discovered in the region in 1991 with the box cut portal commenced south of the pit in 1995 and underground ore production commenced in 1998, after completion of the profitable Callie Open Pit. Development is currently occurring at depths of over 700 m with the decline currently below the 640 Reduced Level (RL) level (surface RL of 1400) with production haulage from 600 m below the surface. The combination of auto compression, a moderate geothermal gradient of 2¦C/100 m and diesel heat transfer causes the wet bulb temperature of intake air at the bottom of the mine to be typically 5¦C higher than on the surface. Wet Bulb temperatures can be up 5¦C higher again in active areas under secondary ventilation. During the 2002/2003 wet season many activities in the lower levels of the mine were stopped due to miners experiencing adverse heat related symptoms or the temperatures exceeding the Underground Heat Management Procedure stop job criteria of 32¦C wet bulb. To improve the working environment, combat the heat related illness and improve operational efficiency, a temporary 1.8 MW refrigerated cooling plant consisting of three 600 kW modules were installed underground to provide bulk air cooling for the lower levels of the mine during the 2003/2004 wet season. Several studies have been conducted in relation to future ventilation demands at Callie and all came to the conclusion, that some mine cooling will be necessary for Callie to meet the high production and development demands. This paper will describe the ventilation network at the Callie Underground operation focusing on the installation, operation and effectiveness of the temporary underground refrigeration plant.

Jan 1, 2005

By I Clark, S C. Dominy

Bulk sampling programs are typically applied in coarse gold mineralised systems to verify resource/reserve grades. In recent years, there have been controversies surrounding some results of underground bulk sampling exercises compared to the predictions using diamond drill data. Just how realistic is it to predict 100 t lots from drilling that was designed to model blocks of several thousand tonnes? This study looks at the variation of relatively small units within larger planned mining units and compares some of the geostatistical techniques which purport to provide tools for such studies. Relative difficulty of application, computer timings and summaries of results will be used to illustrate the likely variation in bulk sampling units as opposed to mining units and large-scale planning units. A case study based on publicly available data from a gold project in North America is presented. A simplistic and unconditional geostatistical simulation model demonstrated that up to 50 per cent of a relatively high-grade mining block could show as uneconomic low-grade subblocks. A subsequent study will consider a similar demonstration using uniform conditioning. Erroneous impressions of early sampling results can lead to unsupported prejudgements of the final results. Bulk sampling programs require detailed planning based on ore characteristics, where protocols must fit the mineralisation type. Any program requires definition of aims and data quality objectives across grade, geological, geotechnical and geometallurgical parameters.CITATION:Clark, I and Dominy, S C, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Eighth World Conference on Sampling and Blending , pp 3–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Manula C. B

The total systems model for underground oal mining planning and design is a set of omputer programs which encompasses a realis- ic reproduction of the interaction between he geological, environmental, equipment, meth- ds and the health and safety aspects of the ining plan. The total system includes nine ajor subsystems - Geology and Reserves, Meth- ne Generator, Roof Support, Subsidence, Pro- uction, Rail Haulage, Cost, Water Generator, nd Ventilation. The subsystems themselves re divided into two categories based on the requency with which they are executed. Event riented Subsystems are executed either inde- endently, or at discrete intervals when cer- tain specific events occur. Dynamic subsystems 'unction interactively during the production :ycle. They transfer data to or request data `rom event oriented subsystems only when spe- ific events occur. Three specific areas for iodel application are in the measurement of system performance, the development of the '_ nterrelationships of the components of deep Wining process and the evaluation of new and Lnnovative mining technology.

Jan 1, 1977

By L J. Strachan, O J. Hawes, S W. Crossen, R C. Roberts

The Albany Conglomerate is a widespread geological unit found in northern areas of Auckland, New Zealand. It has previously been described as part of the early Miocene Waitemata Group which underlies most of Auckland. Much of the Waitemata Group comprises weak interbedded sandstones and mudstones, but also includes conspicuous conglomeratic units such as the Albany Conglomerate. The Albany Conglomerate comprises a well-cemented mixture of hard pebbles, cobbles and boulders of igneous and metamorphic derivation in lenticular beds. A number of tunnelling projects are planned for the near future in Auckland. Recent experience has shown that the variable features associated with the Albany Conglomerate can make selecting appropriate construction methods very challenging. This paper explores the engineering geological and sedimentological features of the Albany Conglomerate with respect to other conglomerates within the Waitemata Group and the potential implications on tunnelling projects in Auckland. Consideration is given to the extent of proposed geotechnical investigations and the production of geotechnical baseline reports.CITATION:Roberts, R C, Hawes, O J, Crossen, S W and Strachan, L J, 2014. Underground construction challenges associated with the Albany Conglomerate in Auckland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 195–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The limit of pressure to which an underground dam may with safety be subjected, is a question that-as far as the writer knows has not received the same attention from authorities on engineering construction, or practical mining, that has been accorded to questions on which the design and strength of other structures or machines in connection with a mine are based. That dams may, under certain conditions, be constructed to resist water under great pressure is a known fact. But the difficulty of demonstrating beforehand that any proposed structure of this kind will withstand the pressure and be effective is, owing to the indeterminate nature of some of the risks to be provided against, very great. In the present state of our knowledge it may almost be laid down as a rule, that a dam of this kind should not be undertaken where grave consequences would attend failure until experience of structures where the physical conditions are similar, but where there are no such risks, has given assurance that such work would stand.In Mines and Minerals for May, 1900, there is published a paper by Mr. James McNaughton describing the construction of three underground dams in the iron mining district of Michigan.The first of these was put in to hold back a flow of 750 gallons per minute, which when pent up created a pressure of 276 pounds per square inch, showing that the height of the sustained column was about 635 ·feet. The hole through which the water issued was in the bottom of the cross cut it was enlarged by removing all loose rock for a depth of 18 ft...

Jan 1, 1901

By Erickson M. E, Smith C. K, Carswell J. T

Thirteen holes totalling 3200m were surveyed using a downhole time domain Geonics EM37 system at the 830 metre level within the CSA Mine, Cobar, New South Wales, in order to search for blind, electrically conductive sulphides at some distance from exploration drillholes. A significant off-hole conductor was detected in only one drillhole.Geophysical modelling and interpretation of the survey results indicated that this off-hole conductor was caused by a sulphide lens 30 metres from the drillhole at a hole depth of 220 metres.

Jan 1, 1990

By Clark T. M

Underground coal mining involves the disturbance of natural strata stresses formerly in equilibrium, the production of noxious and flammable gases and dust which can be both an explosion and a health hazard. It involves also the use of heavy, large equipment operating on natural floors and in confined spaces. Such operations are required to be carried out under artificial light. Much of the easier won coal, that is the shallower coal, from this State has already been extracted and in future workings will be required to go deeper. As the depth increases strata pressures will increase, gas production is likely to be greater and the production of dust will also increase. A further problem which has not yet reached significant proportions in Australia is the potential rise in working temperature. This will be occasioned not only by the use of large items of equipment which themselves generate heat, but due also to thermal gradients as the depths increase. The need for better employee training is now being widely recognised throughout the industry. Under present highly mechanised conditions new employees should not be required to work with or near heavy mobile machinery without proper training

Jan 1, 1976

Excavation through fill material in underground metalliferous mines is usually avoided where possible, unlike in Civil Engineering application where excavation through soft ground is normally a matter of course. In the mining situation, where excavation is normally for access only, then excavation designs are engineered for mining in hard rock, except where previous lack of forward planning has made such excavation inevitable or a mining strategy sequence necessitates some mining through fill in order to achieve optimum recovery of ore. Historically, this has been the case, because of the lack of knowledge of the support characteristics of the fill material placed underground and the lack of knowledge of the composition of the fill material as placed. The expertise and experience available from mechanised excavation techniques in Civil Engineering application (shield jacking, forepoling, spiling, and soft tunnel boring, to name a few) are available for application to the underground mining situation if the need ever arises. This paper describes the situations in underground mining development where mining through fill material is required, the different types of fill material encountered and the types of support available

Jan 1, 1981

By R Justa Cámara, J María Bertrán Llop

"The need for suitable geotechnical characterisation of the rock mass for underground construction is evident. The enlargement project of Railways of the Generalitat of Catalunya (FGC) in Sabadell is a patent example.In general, it is uncommon to encounter problems in the identification and characterisation of certain relevant weak rock formations, which affect project designs. However, all materials should be properly studied, as mischaracterisation can lead to a suboptimal design, resulting in construction problems during the course of the work.Good quality rock is generally not difficult to characterise, but this is not the case for Quaternary or Tertiary cemented soils. Geotechnical investigations based on boreholes do not provide enough information because samples are often badly damaged during the drilling process, if appropriate techniques are not taken. The samples can be altered and may not be representative of the in situ?material.The design and construction of the extension to the FGC line in Sabadell highlighted the importance of the characterisation of Quaternary and Tertiary cemented soils, in particular their rigidity and its underestimation. The twin tunnel project had a total length of 5.1 km, including five stations with 3.5 km excavated by tunnel boring machine (TBM). The remaining 1.6 km was constructed using cut and cover methods. The TBM portion of the tunnel had a bored diameter of 6.83 m with an internal radius of 3 m and 0.25 m thick precast concrete segments. Much of the tunnel alignment passed through and was affected by the presence of certain stiff layers of Quaternary cohesive materials.In this paper the TBM challenges faced will be discussed in detail. In particular:  TBM excavation rate reductions and overheating problems due to the required excessive thrust and torque floating problems in the lining due to nil earth pressure over the rings and the development of an improved, controlled setting time mortar to address this issue block-in and block-out methodology for each station, in some cases with internal blocks to prevent earth pressure drops and soil scouring the relevance of performing simpler solutions, for example, hyperbaric interventions to examine the cutter wheel tools when it has been shown that interventions under atmospheric conditions were equally feasible the implementation of conventional bivalve machines as standard procedure for excavation of diaphragm walls in stations, where in fact, hydrocutter machines or pile boring machines may have been required, given the mechanical characteristics of the materials to be dug out.CITATION:Justa Cámara, R and María Bertrán Llop, J, 2014. Underground extension of the FGC line in Sabadell through cemented soils, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 161–170 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By M Svartsjaern, D Saiang and K Mäkitaavola

The Kiirunavaara mine is a large-scale (28 Mt/a) iron ore mine located in northern Sweden. The mine is owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB) using sublevel caving (SLC). The SLC area underlies an open pit decommissioned in the 1950s, the current main SLC haulage level is situated at an depth of 1100 m. The main orebody dips 60 degrees to the east with a distinct boundary defining the hanging wall to the east and footwall to the west. Since the 1980s damage has been observed both in the footwall rock mass as well as on the footwall crest of the open pit. Recent investigations indicate that the underground footwall damage is primarily controlled by large-scale slope failure mechanisms. Structurally controlled near-vertical planar shear failures in the upper footwall appear to be driven or facilitated by a step-path like curved shear failure situated in a zone starting ca 250 m, and intersecting the SLC about 100 m above the active mining level. To confirm this failure evolution a pilot underground measuring system has been designed and installed to monitor the expected rock mass displacements indicated by numerical models based on the above mechanisms. The systems consists of 50 m time domain reflectometry (TDR) coaxial cables installed in the footwall both across and away from an estimated damage extent boundary to monitor shear movements along natural joint surfaces. The TDR installation is combined with long extensometers to facilitate differentiation between diffuse shear and rock mass normal expansion. Additionally, a low-tech system of tape extensometer lines are installed in drifts and stopes running perpendicular to the ore strike to monitor horizontal displacements in the infrastructure as the footwall ‘slope’ loses confinement during mining advance when the mined out areas are replaced by caved rock from the hanging wall.CITATION:Svartsjaern, M, Saiang, D and Mäkitaavola, K, 2016. Underground footwall monitoring at the sublevel caving mine – Kiirunavaara, Sweden, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 773–780 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A proved routine mapping practice is described involving detailed observations on grade and structure. The equipment and methods employed are giving good service under the conditions encountered. Stopes are mapped on every floor whether timbered or open, "Kodatrace" workplans and sections being used, and in addition all development whether in country or lode is mapped.INTRODUCTIONThe accumulation of geological data for application to current mining problems and to the search for new ore involves the necessity for close mapping of all available underground faces and backs. The technique which has been developed to suit conditions at the North and British mines of North Broken Hill Limited forms the subject of...

Jan 1, 1940

Mt Waruwari, host to the Porgera underground gold mine in the Highlands of Papua New Guinea (PNG), is a prominent ridge of sediments and dioritic intrusives rising approximately 600m above the surrounding valley floor. Consequently, mining occurs in a low stress environment where structural and material considerations are foremost in the design of ground support and reinforcement. Three major rock types are encountered in the underground mine. These are locally referred to as "black sediments" (slightly indurated mudstones and clayey siltstones), "altered sediments" (derived from black sediments by thermal metamorphism), and "intrusives" of dioritic composition. The rocks are moderately to highly fractured, the black sediments being generally weak and occasionally sheared while the altered sediments and intrusives are quite strong but often brittle. Mining takes place from a series of stopes extracted by either slot and mass blast or a modified vertical crater retreat method (VCR), which are backfilled with a cemented rock fill. Ground support and reinforcement has been relatively conserv- ative to date and generally relies on pattern reinforcement of all development with cement grouted "rebar" bolts and mesh, extending to pattern cable bolting with occasional mesh in stope backs. In addition there has been considerable reinforcement of stope hangingwalls in some cases. A programme of broad scale structural mapping, monitoring with extensometers, material property testing, and stress analysis has been devised to allow optimum design of ground support and reinforcement in the future. Considerable work remains to ,omplete this task.

Jan 1, 1991

An underground storage and filling distribution system is presently being established at North Broken Hill Limited in the No.3 Shaft area. This has been necessitat- ed by the dependence of the present filling system on the No.2 Shaft and its imminent closure due to cessation of production. The storage will consist of three tanks excavated in low grade ore, between the No.20 and No.21 levels, at approximately 2700 feet below the surface. The tanks will each have a capacity of 1500 cu yds. Consideration was given for surface storage, although under- ground storage was thought to have greater merits. Two tanks have been excavated, and are in operation. Three or more outlets are installed beneath each tank, with horizontal connections into the No.21 level 'mixing box'. Water decants from the top of the fill in the tanks, and passes into a decant water sump, at the bottom of which is a borehole to the No.21 level. This is then connected to the mixing box and water used as make-up water with the semiwet solids for transport into the existing pipe distribution system. Preliminary results of the system have been satisfactory and it is envisaged that this system will readily cope with the filling demands of the future.

Jan 1, 1973

By M Schmid

German hard coal mining operations have decreased for more than 40 years. Current political decisions are leading to a discontinuation of subsidised black coal mining by the year 2018. This decision will, however, be reviewed once again in the year 2012. The enormous increases in productivity, which were achieved in previous years, have so far not led to an achievement of market requirements. Coal mining at depth of more than 1200 m in multiple seam environments is not yet competitive in global comparison. In 2008 the 24 faces left in eight mines produced about 20 million tonnes of usable steam coal. Management and the workforce will be reduced in parallel; from today until 2012 by more than half. The average age of personnel is increasing dramatically and nearly no new personnel are recruited. With this background in mind, increasing continuously coal mining productivity becomes more and more difficult. Above all, this goal was reached by mechanisation, then by increasing the mining machine power and then by enhanced machine control systems. The first attempts to automatically operate full face equipment from above ground were in the early 1980s. After successful automation of the face equipment, the emphasis is now on mine logistics. Autonomous monorail transport was introduced and tested in 2007. Since the development rate of machine improvements has its limits, the focus is on the full interaction of the total production system. Here information technology (IT) becomes important; the driver for more productivity. Actual developments aim for the complete and general homogeneous IT infrastructure both above ground as well as underground. The explosive environment needs high level investments in safe technology, eg access points for WLAN and fibre optics for underground use (ATEX certification). New technology availability also drives the enhancements of management and process control systems. Innovations in the mining industry often comprise technology advances through the adoption of well-known technologies. With virtual reality (VR) teaching and training systems advanced computational instruments, both in software and hardware development, were applied in the German coal mining industry for ten years. Widening lists of applications as well as the encouraging achievements show the economical benefits of investing in virtual reality technology both for teaching and training and for knowledge management. The paper discusses the actual technical achievements as well as in IT infrastructure utilisation and also in employment of virtual reality based systems. Special focus and deeper insight will be given to the fibre optics and WLAN hardware integration as well as software developments. The pocket personal computer (PC) is used to enhance underground material transport and data acquisition. The knowledge-based maintenance system (KBMS) integrates real-time virtual reality knowledge elements, such as repair process descriptions. It gives access to expert documentation by intelligent search algorithms and 3D representations of major mining machinery.

Jan 1, 2008