Search Documents

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

Electrochemistry Measurement, Using Chena Analyser, to Investigate Selective Separation of Pentlandite and Pyrrhotite

Sep 13, 2010

By Manuel Sanchez, Marcial Medina, Matt Hurley, Hugo Granados, Pramod Kumar, Raj Rajamani, Jose A. Delgadillo

"Large-diameter ball mills have traditionally used steel liners—steel being a highly durable material that can be shaped into any desired geometry, among which the double-wave has been the preferred design. Such a design produces a purely cascading charge motion, which is ideal for the shearing action needed to produce a finer product. Today, however, rubber liners, which have been in existence for over forty years, are now preferred over traditional steel, largely because they weigh less and are easier to maintain. In this paper, we show the operating data from the Hudbay Minerals’ Constancia Mine, wherein the liners on a 26-by-40-foot mill were changed from conventional steel liners to PolyStl™ liners. It is then shown that this change reduced the amount of energy consumed whilst being able to maintain previous grind and throughput levels. The design is verified via discrete element simulations.IntroductionThe Constancia Mine (“Our Business: Peru,” 2016) is located in the southeastern Andes of Peru, at an elevation of approximately 4,200 m. It can be accessed via the CU-126 road, about 95 km from the town of Espinar in Espinar Province. The mine also contains both the Constancia and Pampacancha deposits in the Province of Chumbivilcas. Hudbay Minerals, Inc. acquired the mine in 2011, through the purchase of Norsemont Mining, Inc. and currently retains sole ownership of the property. Production of the Constancia Mine began in 2014, with commercial production levels being achieved in April 2015.The Constancia and Pampacancha deposits primarily include hypogene, supergene, and skarn ores. The Mine’s main products, however, are copper concentrate, with silver contents, and molybdenum concentrate. These mineral reserves are expected to last approximately 22 years. Constancia’s open-pit mine supplies a processing plant that is designed for 81,900 metric tons per day of throughput. Average annual copper production is estimated to be 82,000 mT (contained metal in concentrate). Actual plant production can be found in Table 1."

Jan 1, 2017

In the extraction of level bridge pillars in the South Mine by square-setting methods the general practice is to work transversely from the hanging wall in narrow sections three or four sets wide to the depth of the bridge-usually three sets. When the working block attains an area of twelve square sets, sand filling is run in, either by pneumatic (Proceedings No. 123, 1941) or hydraulic methods, in order to control the settlement of the general area and prevent the development of undue weight in the stope. Upon completion of the filling operations, or coincident with them, ore breaking is resumed and the transverse section of the bridge pillar gradually reduced. A number of these parallel sections may be working at the same time.In preparing a block of sets for filling a great deal of paddocking is required, both to contain the filling and to preserve access to ladderways and ore chutes which may be situated at some horizontal distance. Stope paddocking until recently was constructed of 10 in. x 2 in. boards nailed...

Jan 1, 1942

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

By N. L. Ayres

Tendon support systems have been successfully used to stabilize excavations. Tendon support systems are routinely designed using the axial load-bearing capacity of tendons, namely the tensile strength. To attain tensile strength the tendon must be loaded along its length, which often does not occur in practice. Tendons should optimally be installed at 90° to the surface of the excavation to achieve maximum penetration depth, yet this is often not physically or practically possible, and installations at angles less than 90° occur. Furthermore, the intersection of geological features within the rock mass frequently results in complex loading situations on tendons. The position and angle at which loading occurs results in different combinations of tensile and shear forces acting on the tendon, which can impact on the support performance of each unit and ultimately the whole system. All factors that influence the support system should be understood and taken into account to ensure a sound support design. Combination loading situations are further investigated and tested to obtain a better understanding of the mechanisms involved and the effects on tendon load-bearing capacity. Tendon support units were tested at different installation angles to establish the tendon performance, mechanical behaviour, and load capacity during these loading situations. The results and outcomes are aimed at providing rock engineers with additional data and improved understanding of how tendons could perform under certain conditions.

Jan 1, 2014

By Garry Johansen, Andrew McCallum, Sandy Gray, Gary Patrick, Jennifer Abols

"The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flowsheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit.The InLine Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size – saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements.When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores - some of which may not currently be economically feasible using standard processes and flowsheets. We have provided three examples of such projects, where an alternative to whole ore leach and CIP or CIL has delivered these benefits."

Jan 1, 2003

By Juan Alfredo Espinoza Huamán

Las operaciones mineras subterráneas necesitan cada vez más indicadores de seguridad, calidad y productividad. En ese sentido, el presente texto señala la importancia del manejo de voladuras dentro de la minería subterránea a través del análisis de las vibraciones para determinar la influencia de daño como respuesta a los índices de caracterización geomecánica del macizo rocoso. De forma que se pueda aportar minerales contínuamente, desarrollar la mina y tener más sostenibilidad en el tiempo.

Jan 1, 2015

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

By Juan Carlos Llorente

El autor plantea en este artículo interrogantes diversas respecto del futuro de los acuerdos de trasferencia tecnológica y las razones de su existencia y desarrollo, no solo en el sector minero, sino también en el resto de sectores. Se pone de relieve su importancia, tanto en el ámbito empresarial como universitario, en todo lo relativo a los temas de investigación, desarrollo e innovación (I+D+I).

Jun 30, 2020

By J. Searra, M. Aboagye

"For new mining projects or for medium- to long-term areas of existing mines, drilling data is invariably on a relatively large grid. Direct estimates for selective mining units (SMUs), and also for much larger block units, will then be smoothed due to the information effects and the high error variance.The difficulty is that ultimately, during mining, selection will be done on the basis of SMUs on the final close-spaced data grid (grade control), which will then be available, i.e. the actual selection will be more efficient, with fewer misclassifications. However, this ultimate mining position is unknown at the project feasibility stage and therefore has to be estimated. This estimation is required because any cash flow calculations made on the basis of the smoothed estimates will obviously misrepresent the overall economic value of the project, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the average grade of the orebody. Similarly, unsmoothed estimates will be conditionally biased and will give even worse results, particularly in local areas of short- and medium-term planning or mining.This paper presents a case study of indirect post-processing and proportional modelling of recoverable resources designed for mediumand long-term mine planning at the Gold Fields’ Tarkwa Mine in Ghana. The case study compares long-term indirect recoverable mineral resource estimates based on typical widely spaced feasibility data to the corresponding production grade control model as well as the mine production. The paper also proposes certain critical regression slope and kriging efficiency control limits to avoid inefficient medium- to longterm recoverable estimates, and highlights the danger of accepting block estimates that have a slope of regression less than 0.5."

Jan 1, 2015

By Tellis D. A

An outline is given of the general position of earthsciences information in Australia, the background to development of the Australian Earth Sciences Information System (AESIS) and the role of the Australian Mineral Foundation in developing and co-ordinating the projeot in co-operation with the CSIRO, BMR, National Library of Australia, AGIA, and many companies.Details 'of the system, method and anticipated rate of input (especially of unpublished material at which the System particularly aims), mode of dissemination, and use of the data base are discussed. Information on theAustralian Thesaurus of Earth Sciences and Related Terms and brief details of some 30 earth sciences information collections in Australia is given.

Jan 1, 1977

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By Edwin Uribe

La Compañía minera Raura es un yacimiento tipo skarn de zinc, plomo, cobre y plata que tiene un solo halo metasomático explotado (Complejo Catuva), además de cuerpos distales de reemplazamiento, vetas y bolsonadas. En ese sentido, los estudios geoquímicos y geológicos a través de la magnetometría y polarización inducida señalan una mayor visión del yacimiento para la búsqueda de nuevos recursos que permitan un enfoque de minería con mayores volúmenes de producción a menores costos y valores de mineral por tonelada. Así también, se ha logrado encontrar un nuevo halo de skarn mineralizado llamado “Franja Hada– Farallón” y una nueva estructura tipo mantiforme llamada “Manto Nadine”, las cuales posibilitan diseñar métodos de explotación masivos tipo taladros largos y pensar en piques de extracción en Raura.

Feb 1, 2014

By A. Anani

The need to optimize surface mining operations has led to the use of discrete event simulation (DES) modeling of truck-shovel systems. Often, these models assume truck cycle times are independent and identically distributed (iid) random variables, although, with significant bunching on the haul routes, this may not be valid. The objective of this paper is to present a methodology to (i) account for truck bunching due to slow trucks; and (ii) test for cycle time dependence (i.e. whether truck cycle time data is iid or not). We built a DES model that accounts for bunching due to a slow truck(s) and used the cycle times as data for further analysis. We then tested for cycle time dependence using Pearson correlation coefficients. The results show significant correlation of truck cycle times for different number slow trucks, with variable speeds. Assuming iid in modeling results in over-estimation of productivity and the uncertainty surrounding it. The over-estimation of uncertainty is pronounced when the relative difference in truck speed increases. The confidence interval of the means of truck loads/shift decreases with increasing number of slow operators. This work extends the usefulness of DES in truck-shovel applications.

Feb 27, 2013

By Efrén Peña Pino

El presente texto señala la aplicación del sistema SAP en la minería subterránea de Minsur. Este sistema operativo maneja las propiedades y procesos de la Sociedad Minsur, el cual cuenta con tres Centros, dos de los cuales son operativos (San Rafael y Pisco) al margen de la central de administración (Lima) y permite la planificación de todos los recursos de la empresa de manera integral, evitando imprevistos y una mejora de decisiones.

Jul 31, 2003

By Benoît Demers

Dans ses opérations de traitement de concentré de zinc, l?usine de Zinc Électrolytique du Canada à Valleyfield génère un résidu minier appelé « jarosite ». Jusqu?en 1998, le jarosite était transporté hydrauliquement dans des bassins construits en argile. Le jarosite sédimenté possède une consistance très molle (impossible de circuler à pied sur le résidu consolidé) avec une eau interstitielle acide contenant des teneurs élevées en métaux. Ces caractéristiques particulières au jarosite rendaient très coûteuses la construction et la fermeture des bassins de résidus. En 1998, Zinc Électrolytique du Canada a implanté un nouveau procédé, développé chez Noranda, dont le principal objectif était de stabiliser chimiquement et physiquement le jarosite. Un nouveau concept de déposition a été élaboré pour le nouveau résidu minier appelé « jarofix ». Les grandes caractéristiques du nouveau procédé et du concept de déposition sont : ? Le jarosite est lavé et déshydraté à l?usine avec un système de filtre; ? De la chaux, du ciment et de l?eau sont ajoutés pour former le jarofix; ? Le jarofix est transporté par camions jusqu?à l?aire d?accumulation; ? À l?aire d?accumulation, le résidu est géré selon un concept d?empilement. L?élaboration du concept d?empilement et de l?aire d?accumulation devait tenir compte des caractéristiques de déposition du jarofix, de sa résistance à l?érosion hydrique et éolienne, de la gestion de l?eau de ruissellement, de la faisabilité de construire les digues de ceinture en utilisant du jarofix durci et de la nécessité de restaurer progressivement l?aire d?accumulation. Le déchargement du jarofix se fait à partir d?une rampe qui progresse avec une pente ascendante pour développer un front de déversement de plus en plus haut. La hauteur du tas de jarofix atteindra 30 m au centre du site. L?aménagement initial de 1998 a inclut une digue d?amorce de 3 m de hauteur, une rampe de déversement de 8 m de hauteur et un bassin pour la gestion de l?eau de ruissellement. Les propriétés du jarofix consolidé dans l?aire d?accumulation sont déterminées annuellement. Le jarofix durci possède la consistance et la résistance d?une argile très raide. Sa conductivité hydraulique est similaire à celle d?un silt et il résiste bien à l?érosion éolienne. Après trois années de déposition, la température du jarofix au milieu du dépôt demeure élevée. Le jarofix durci est facile à excaver et à compacter, ce qui en fait un excellent matériau pour la construction des digues de ceinture en périphérie du site.

Nov 1, 2002

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012