Search Documents

By Christopher Mark

Knowledge of in situ stresses is fundamental to many studies in earth sciences, and coal mine ground control is no exception. During the past 20 years, it has become clear that horizontal stress is a critical factor affecting roof stability in underground coal mines. The theory of plate tectonics and the World Stress Map (WSM) project has been extremely helpful in explaining the sources and the orientations of the horizontal stresses observed underground. Recently, WSM geophysicists studying deep-seated stresses have developed a model of how stress magnitudes vary with depth in the crust. They have devoted relatively little attention to near-surface stresses, however. This paper explores the relationships between deep-seated and shallow in situ stresses in several of the world?s coalfields, using a data base of more than 350 stress measurements from underground coal mines. The analysis indicates that distinct regional trends exist, corresponding roughly to the regional stress fields identified by the WSM. The paper presents equations for estimating stress magnitudes that were developed by treating depth and elastic modulus as independent variables in regression analysis. The magnitude of the horizontal stress increases with depth, at rates that range from 0.8 to 2.0 times the vertical stress, just as the WSM ?critically stressed crust? model predicts. Overall, it seems that the stress regimes encountered in underground coal mines are closely linked to those that exist deep in the earth?s crust.

Jan 1, 2008

By T. B. Acton

There are two types of ore transportation systems in use at Newmont's Magma Copper Co. San Manuel mine in Arizona-rail-mounted, box-type rotary cars and the newer rail-mounted, bottom-dumping ASEA cars. Though the cost per car for the ASEA units greatly exceeds the cost per rotary car, the advantages of the ASEA units, including much faster dump times, have made the ASEA system a successful alternative at the San Manuel mine. The rotary system of ore transportation has been in use at San Manuel since production began in 1956. The system employs 7.9-m3 box-type cars to transport ore by rail to shaft pocket areas. A rotating dumping mechanism turns three cars at a time upside down to empty them, and returns them to an upright position. Trains of 15 cars each are dumped in about six minutes. Each 15-car train is pulled by an 18-t rated trolley locomotive. There are about 400 rotary cars in service at San Manuel and the system is used for the majority of ore haulage. This well-proven rotary method was instrumental in achieving the December 1977 world record of 272 Mt hoisted from an underground copper mine. Magma Copper Co. began using ASEA cars in late 1977. Designed by ASEA of Sweden, the cars are built for San Manuel by Kasper-Hall Manufacturing Co. in Tucson. The cars basic design feature is a hinged floor that opens at the side as the car is pulled through the dump. As it passes over the dump, a fifth wheel attached to the hinged floor (opposite the hinges) travels along a rail in the dump. This rail dips down into the pocket and then returns to track level. As the fifth wheel travels along the rail, the car floor opens, the car dumps, and the floor is then returned to track level. As the car is dumping, the body remains suspended over the pocket by wheel rollers attached to each side of the dump. Trains of 10 cars each are emptied in about 45-50 seconds. Each ASEA train is pulled by an 18-t rated trolley locomotive, adapted at San Manuel to allow it to pass through the ASEA dump. At minimal cost, "wings" are welded to each side of the locomotive. These wings suspend the locomotive over the pocket as the train passes through the dump. Advantages of the ASEA System Major design characteristics of the ASEA and rotary systems are shown in the accompanying table. The comparison points out some of the following advantages demonstrated by the ASEA system. • Faster dumping-An ASEA train dumps in 50 seconds, while a rotary train takes at least six minutes. There is no stopping or starting when dumping an ASEA train. The train enters the dump area, dumps, and leaves in one continuous motion-in contrast to rotary trains which must stop and start five times to dump. With the rotary system, three cars are spotted in the dump mechanism by remote control. When the cars are in place, the train operator activates the dump, the cars are turned over, and then returned to an upright position. This process is repeated until all 15 cars in the train are emptied.

Jan 4, 1980

"The mission of the Respirable Dust Center is to enhance the health, safety and productivity of the miners 'through advancing the fundamental .understanding of all aspects of respirable dust associated with mining and milling and the interaction of dus.t and lungs for reducing the incidence and severity of respirable dust disease. All Dust Center activities are focussed to be responsive to this mission which is shared by several federal agencies closely associated with the Generic Mineral Technology Center for Respirable Dust such as USBM, M,SHA, and NIOSH, and the mining industry. While significant progress has been achieved in making mine atmospheres cleaner and healthier, respirable dust disease remains the nations worst industrial hazard. GOALSThe goals of the Respirable Dust Center have been formulated to recognize the diverse scientific, engineering and medical aspects of respirable dust as well as the need to enhance the interaction, education and technology transfer in the respirable dust area.The Center goals are to:1. Enhance the understanding of the scientific, engineering and biological characteristics of fine and respirable mineral particles, fibers, organic aerosols, and complex particles found in the mining and milling atmospheres.2. Advance the understanding of the physical behavior of airborne respirable dust particles in flowing streams under different. stimuli during mining and milling.3. Advance fundamental understanding of the causative mechanisms for the occupationally related lung impairments and the airway diseases of mine and mill workers.4. Establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment and control measures) in the generation, exposures, and pathogenic properties of fine particles.5. Contribute to the development of control mechanisms for reducing ambient respirable dust concentrations, worker exposure, the incidence and severity of dust related lung disorders and disease prevention in mining and milling atmospheres.6. Enhance functional integration among the various research personnel in the Center, as well as, with other groups, such as MSHA, NIOSH and USBM involved in respirable dust research and control.7. Develop technically trained personnel for employment in the mineral industry for respirable dust research and control.8. Enhance the availability of respirable dust-related information utilizing several technology transfer avenues."

Jan 1, 1990

By J S-L Chan

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Cu-Ag-Au mineralisation at Kluwih prospect in Eastern Java, Indonesia is related to a high-sulfidation hydrothermal system within a volcanic dome (2.35 × 1.7 km diameter). The mineralisation occurs mainly in steeply dipping, structurally-controlled quartz-enargite-pyrite veins (several centimetres to 2 m wide) and is hosted mainly in porphyritic dacite, volcaniclastic rocks and volcanic breccia of the dome and in an underlying andesite that yielded a zircon U-Pb age of 11.5 Ma.Short wave infrared spectrometer analyses were carried out for alteration mapping at Kluwih. There are two main stages of alteration produced by the hydrothermal activity. The alteration mineral assemblages indicate an advanced argillic alteration. The Cu mineralisation occurred in the form of enargite and subordinate chalcopyrite with an intergrown texture in the early stage. These mineralised veins are characterised by narrow pyrophyllite ± diaspore and dickite selvages (metres wide) and a peripheral K-muscovite envelope (sericitic alteration) up to 100 m wide. The K-muscovite envelope is zoned outward to Na-muscovite or Na-illite. Late-stage kaolinite and smectite alteration overprints the porphyritic dacite and may obscure the nature of early mica-clay alteration. The spatial distribution of different alteration assemblages suggests that the temperature of hydrothermal fluid increases with depth.Both the high-sulfidation mineralisation and advanced argillic alteration are suggested to be related to magmatic-hydrothermal fluids, which are likely to originate from an undiscovered deeper porphyry Cu-Au system below the porphyritic dacite. Based on alteration mapping results and comparisons to similar deposits, the porphyry intrusion could be up to 500 m below the volcanic dome. Further geochemical and mineralogical studies may help to target the potential underlying porphyry system.CITATION:Chan, J S-L, 2015. High-sulfidation epithermal Cu-Ag-Au deposit, Kluwih, eastern Java, Indonesia – alteration and implications for potential porphyry cu mineralisation, in Proceedings PACRIM 2015 Congress, pp 213–218 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Toshiharu Teranishi

When we apply the Au nanoparticle superlattices to the future nanooptical and nanoelectronic devices, the control of not only the particle size but also the interparticle spacing and symmetry of superlattice are the essential problems to be overcome. First, we developed a novel synthetic procedure to precisely control the particle size of alkanethiol-protected Au nanoparticles in the range from 1.5 to 9.7 nm by the heat-treatment of the small Au nanoparticles in the solid state. Absorption and nonlinear optical properties of alkanethiol-protected Au nanoparticle superlattices were then elucidated. On the other hand, the hexagonal close-packed (hcp) 2D superlattices of small Au nanoparticles with the interparticle spacings from 1.9 to 3.6 nm were successfully prepared by using newly-synthesized ligand for single electron tunneling devices. Finally, various symmetric superlattices, such as chain (2-fold), quasi-honeycomb (3-fold), square (4-fold), etc., of Au nanoparticles could be produced by making use of interligand interactions or some templates.

Oct 1, 2003

One of the chief drawbacks to Bendigo mining always has been the difficulty of draining the mines in an equitable manner, so that each company or mine owner bears the properly share. The trouble seems to have been apparent on this field since the diggings were discovered. One mine would push on more expeditiously than its neighbour in looking for the precious metal and sink its shaft, whilst those in the vicinity would simply potter about, and discontinue sinking until gold was struck in the deeper ground, and: then they would go ahead, start sinking, while the pioneer would have to pump all or most of their water. This sort of thing continued here for years until the leases were worked down to the very deep ground and the water became such a b.urden on those companies that had deep shafts, that first one stopped hauiing and then others; with the result that over 1000 feet of water was allowed to accumulate on the New Chum line. lt appeared that if something were not done the whole of the main line of reef in the Bendigo district would be at a standstill, when a scheme was formulated and handed to Mr. Lansell, who, with other gentlemen, took the matter up, and at the present time all the mines on that particular portion of reef are in full work and the water all bailed out.lt is this scheme that I am requested to place before you and also to give you the details of the work done since its adoption.

Jan 1, 1902

The early records of hydraulic elevator and bucket ladder dredging in the Clutha River system indicate the success of that era of alluvial gold mining in Otago. This paper briefly reviews parameters of depth and gold grade for alluvial operations. The application of dragline technology is proposed for the economic removal of overburden to target the deeper alluvial gold areas which remain in the Otago region.

Jan 1, 1992

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

By David R. Jessey

Water pollution problems associated with surface metal/nonmetal mines throughout the United States were assessed. Three major problems were identified: acid mine drainage (AMD), toxic concentrations of heavy metals and excessive sedimentation. Several factors affect the type and amount of pollutants generated at a mine site. Among these are hydrologic regime, geology, mineralogy, topography, climate, size of the mineralized area and mining method. Nine surface mines situated in distinctly different settings were visited and their pollution problems studied. These mines were located in Morenci, Arizona; Hayden, Arizona; Sauharita, Arizona; Cobalt, Idaho; Spruce Pine, North Carolina; Iron Mountain, California; Butte, Montana; Fernwood, Idaho; and DeLamar, Idaho-Oregon. A detailed evaluation of the pollution problems at the Morenci mine indicated that a diversion system and treatment pint would be the most effective means of abatement for the existing water quality problems. Based on the study of the Morenci mine and three other porphyry copper mines with differing problems a water management plan was conceived for a new source copper mine. A companion Appendix Volume containing detailed reports on the mine site visits is on file at the US Bureau of Mines Spokane Research Center.

Jan 1, 1981

By M. Bennett, L. Twidwell

Montana Tech has embarked on a coordinated series of studies to delineate the characteristics of the Berkeley Pitlake containing over 36 billion gallons of acidic, metal-contaminated water formed after the cessation of open-pit copper mining in Butte, Montana, USA. The objectives of the overall series of studies are to summarize presently available information and to generate new and needed information to formulate a conceptual environmental model for the pitlake and to provide characterization data for the development of advanced treatment technologies. In this presentation, the chemistry of the Berkeley Pitlake water is partially reviewed. It is known that the pitlake consists of two distinct layers of water referred to as surface and deep water. Samples of deep water were collected and placed in a 12-ft high and 6-inch diameter column and exposed to different wavelengths of UV radiation as well as atmospheric conditions. Measurements of pH, redox potential (EH), dissolved O2, turbidity, conductivity, temperature, and elemental composition show that the water reacts differently and indicates that the diurnal effects of sunlight likely play a major non-biological role in its chemistry. Resulting technology could be useful for developing an alternative to treating acid-rock drainage.

Jan 1, 2007

By J. K. Whyatt

This report describes a microcomputer-based instrumentation system for structural monitoring of the circular, concrete-lined Silver Shaft in northern Idaho, The 1-ft-thick concrete lining and surrounding rock mass were instrumented with a total of 12 multiple-point borehole extensometers, 16 pressure cells, 22 concrete embedment strain gauges, and 12 thermistors. The instruments were distributed among four test sites and installed immediately above the shaft bottom during sinking at the 2,414, 4,063, 5,191, and 5,955 levels. Limited access to the instruments prompted the development of a microcomputer-based remote data acquisition system that could be operated from the surface. The system scanned the instruments on a programmed schedule, printed out reduced data, and stored the data for plotting and recall. Data acquisition from off-site and uploading of data to mainframe computers were accomplished by the addition of modems to the basic system. The system is suitable for use in monitoring the structural behavior of any deep mine opening, especially in harsh operating environments and where access is limited.

Jan 1, 1986

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By Andrew Cecala

The Bureau of Mines performed tests to compare the effectiveness of steam and of water sprays to reduce respirable dust levels at mineral processing plants. By applying 0.22 wt pct water vapor as steam to product material, a 64-pct respirable dust reduction was recorded. By applying the same amount of moisture with water sprays, only a 25-pct dust reduction was recorded. By increasing the moisture content up to0.5 pct using water sprays, the dust reduction was increased to 55 pet, which was still less than the dust reduction achieved by adding less than half that amount of water in the form of steam.

Jan 1, 1985

By M. D. Aldridge

The results of a two-year research effort aimed at improving communication systems in coal mines is reported. A review of communication methods presently used in coal mines is presented. Theoretical and-experimental results of a four pronged effort in the areas of (1) through-the-earth propagation, (2) paging system design, (3) improvement of wired telephone systems, and (4) carrier current systems are described. Auxiliary systems not included in the above are considered briefly. Various conclusions are drawn in light of practical constraints and the needs of the mining industry. The study clearly demonstrated the need for nine communications to be designed on system basis. The viability of new technology for providing reliable mine communication for improving mine safety and operating efficiency is shown.

Jan 1, 1973

DynoMiner APS Delivery Systems Overview ? New Design of DynoMiner APS-M2 ? Stand alone or attach to Cargo type 10,000 lb (4536 kg) emulsion bins. ? Hose reel w/200-ft (61-m) by 1-inch I.D (25-mm) hose capacity, power rewind. ? Increased water and trace capacity. ? Hose reel and gassing offered as options. ? New Flow Meter ? DN-100: aluminum body, UHMWPE rotors. ? Will be offered as an option. ? APS Nomenclature ? Proposed changes ? DynoMiner APS and APS-M1 to become DynoMiner APS Drifter ? DynoMiner APS-M2 to become DynoMiner APS Stoper. ? Both to have optional gassing / flow metering.

May 1, 2004

By D. J. H. Walker, W. H. Gibson

The inclination of any pit wall composed of stacks of benches is limited by the overall quality and structural complexity of the rock mass in which the slope is situated. For a bench stack angle that satisfies the stability criteria, various combinations of bench height, bench face angle and berm width can be used in the slope design. The bench face angle and berm width geometries must be chosen to fit the bench stack angle but must provide a berm that will be capable of catching the volume of failed wedge material from the bench faces above. Other considerations for bench height and berm width are equipment size, ore selectivity and blasting design. This paper studies the effects of different slope configurations on slope performance as it relates to wedge stability, volume of rock safely contained on berms, and rockfall. Optimisation of the geometry is carried out based on the need to minimise the volume of failed material which limits the effectiveness of the berm. This will reduce the number of rocks that can continue to fall further, reaching geotechnical safety berms or pit ramps, that put safety of personnel and equipment at risk. For general study it is most effective to investigate and compare the performances of each of a wide range of geometrical combinations of bench height, bench face angles and berm widths that fit a variety of different bench stack angles. These analyses were conducted for a predetermined bench stack height and three different bench stack angles.

Jan 1, 2006

By E. W. Thorton

"This paper is intended to show that grinding media can effect flotation results, and in some instances the results are vastly different. I do not suggest that autogenous grinding is beneficial in the separation of all complex base metal ores, in fact I know of a case where autogenous grinding would be disastrous to any selective flotation. I do however contend that prospective flow sheets and reagent balances of any complex base metal ores should be tried with both types of grinding. I feel fortunate that the paper to be presented later in this meeting by Rene Klymouski will, I think, compliment and perhaps explain some of the results of my research.This paper will be in four parts. The first part deals with a literature survey on the subject. Surprisingly enough, very little information has been printed on the subject. The second part deals with results obtained in bench scale tests on an ore from Chester Mines Limited. It was in these tests that we realized that steel grinding was giving us serious problems. So bench scale tests are shown giving results with a stainless steel grind, a mild steel grind and a grind in a ceramic mill with ceramic billets.The third part of the paper deals with results obtained in the Mines Branch Pilot Plant, when again we ground the ore with three different types of grinding media. Incidentally, this has been the only pilot plant test made at the Mines Branch in which flotation products were made on both steel grinding and autogenous grinding on the same ore. The fourth part deals with two other New Brunswick ores and is intended to show that changing the grinding media effects ores other than that of Chester Mines Limited."

Jan 1, 1973

By G. Gavan

Analysis of reported injuries for off-highway haul trucks indicated that 42.7% were slip and fall, and of these 34.1% occurred mounting and dismounting the machine. Redesign of the lower steps was concluded to provide the most overall improvement for increased safety and accident reduction. Various existing, innovative and conceptual designs were reviewed and evaluated. The most promising candidate designs were the four-spring supported lower steps and the center tube mounted lower steps. Both configurations proved to be viable designs as they passed successfully human factors and survivability tests conducted at a large copper mine.

Jan 1, 1979

By Andrew Bamber

Between the early 20th Century and the present, the production of mined copper ore has increased from tens of millions of tonnes per annum to several billion tonnes per annum, an unprecedented increase. Contemporaneously, the average grade of mined copper ore has declined from over 2% to approximately 0.5%. Again, in parallel, the price of copper has increased dramatically to reflect the increasing cost of extracting and beneficiating such large amounts of low-grade ore. Within the period the copper price however exhibited several periods of intense volatility, driven by interrelationships between demand and supply, themselves strongly driven by periodic industry developments in the fields of exploration, ore extraction, mineral processing and extractive metallurgy. It is notable that these periods of intense innovation exhibit a strong correlation to preceding periods of price, demand or production volatility. This paper examines key trends in each theme between 1900 and 2018 and draws strong conclusions as to the interrelationship between them. INTRODUCTION The production of copper metal has increased from around half a million tonnes per annum to over fifteen million tonnes per annum over the course of the 20th Century. Contemporaneously, the average grade of copper ore mined has declined from over 2% to approximately 0.5% copper by weight. As a result, the volume of Run-of-Mine (ROM) copper ore required has increased from around ten million tonnes per annum to over a five billion tonnes per annum over the period, an unprecedented increase. The adage is that demand drives supply, that prices rise in times of high demand and/or short supply, and that prices fall when supply catches up with demand. The market sellers in biblical times knew this well; mediaeval market sellers equally. Dutch tulip sellers in the 1600’s experienced both in extremis — much to their dismay — and the great industrialists and early capitalists of the industrial revolution knew this also. Mining recently went through a cycle where investors and producers both believed that the “old” rules did not apply any more and that the industry was in a “supercycle” where prices would continue to rise on the back of increasing demand. However, as the GFC of 2008–2011 showed, this was not to be. Another adage says that we constantly innovate to lower costs of production. Is this true? Do we only innovate to lower cost? Has the true cost of producing copper actually gone down over the century? Or are there other balancing forces at play? Herb Kellogg, in his Centenary address to the American Institute of Mining Engineers (now SME), categorized two types of innovation: ‘Bigger and Better’, and ‘New Process’ (Kellogg, 1970). ‘Bigger and Better’ allows increased production at presumably lower cost; ‘New Process’ supports the same result at presumably the same scale, but at significantly enhanced efficiencies and (therefore) lower cost. It is suggested that both types of innovation are constantly and interchangeably required to achieve the kind of scale-up, at achievable operating and capital cost that the industry has achieved over the period. What can be shown, over this last Century and a bit, is that supply and demand are indeed inextricably linked, price and demand are linked, but so are price and cost of production. And the innovation required to sustain that weaves in between them all, cost-effectively increasing production capacity or lowering the cost of production at the same throughput, and sometimes both.

Jan 1, 2019