Search Documents

By Harpal Parmar

This paper evaluates dynamic methods of pile capacity prediction by comparing their results to static load test results. Dynamic and static pile load test data were assembled from four southeastern states of the U.S. End-of-drive and restrike capacities were evaluated using the Pile Driving Analyzer (PDA) and by wave equation (WEAP) analyses. These were compared to static (Davisson criterion) loads. The best comparison was obtained for restrike PDA results; restrike wave equation analyses values also compared well. The end-of-drive results for both methods-showed relatively poor comparisons. The PDA was recognized as an important tool to measure energy transferred to the pile; this transferred energy was recognized as an uncertainty when conducting wave equation analyses. A statistical analysis showed restrike capacity results to be associated with higher precision and accuracy as compared to end-of-drive methods. The authors believe that restrike dynamic testing is essential to establish long term static soil strength and that it will lead to accurate and cost-effective design of piles.

Jan 1, 1996

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012

By Roy C. Bartholomae, Jeffrey Shawn Peterson

1. INTRODUCTION In the early 1980s, the U.S. Department of the Interior’s Bureau of Mines Pittsburgh Research Center required that a large reverberation acoustic facility be constructed. This facility was designed to determine the sound power level emissions of mining equipment, especially continuous miners and jumbo drills. A contract for a conceptual design of a reverberation chamber was awarded to Wyle Laboratories of Huntsville, AL, which had extensive experience in the design, construction, and accreditation of acoustical reverberation chambers. The following standards were referenced as guidelines for the design of the chamber: ANSI S1.31-1980, “Precision Methods for the Determination of Sound Power Levels of Broadband Noise Sources in Reverberation Rooms” and ANSI S1.32-1980: “Precision Methods for the Determination of Sound Power Levels of Discrete-Frequency and Narrowband Noise Sources in Reverberation Rooms.” Specific requested criteria included that the room be large enough to accommodate typically large mining equipment and that there be adequate acoustical modal density in the frequency range of interest. It was also required that the room dimensions would support broadband acoustical measurements down to the 100 Hz third octave band. With the closing of the Bureau of Mines in 1996, this reverberation chamber lay dormant for a number of years. However, this facility is now part of the National Institute for Occupational Safety and Health’s (NIOSH’s) Pittsburgh Research Laboratory (PRL). One of NIOSH’s missions is to decrease noise induced hearing loss among the nation’s mineworkers. To this end, PRL researchers are refurbishing and instrumenting this reverberation chamber to facilitate assessment of the various engineering controls being developed to decrease the sound power level emissions of mining equipment. Early on, this work has sought to bring the chamber up to the level of ISO 3743-21 standard for engineering grade measurements for broad-band noise, with a longer range goal of improving the lab to meet the requirements of ISO 37412standard for broadband precision grade measurements. 2. DESIGN OF THE REVERBERATION CHAMBER The nominal room dimensions are 18.3 meters long by 10.3 meters wide with a height of 6.7 meters. The chamber volume is 1,286 cubic meters. These dimensions are important, as few reverberation facilities are large enough to test typically huge mining equipment. The floor is poured concrete with a sealer to make it acoustically reflective. The walls are built of hollow concrete block, 16 inches long x 8 inches high by 12inches thick. Each block has two hollow cores. The hollow block cores were completely filled with concrete with horizontal and vertical steel reinforcing bars 16 inches on center. This was done to supply a

By Lyn Jones, Mike Bratty, Rick Lawrence, David Kratochvil

"The treatment of water is required at many mining operations to remove metals and prevent the discharge of contaminated water to the environment. In other cases, water treatment is used to provide better quality water for recycle to the processing plant, or to process bleed streams in hydrometallurgical operations in order to prevent deterioration in metallurgical performance or process equipment. BioteQ Environmental Technologies Inc. has developed and commercialized the BioSulphide® Process which can provide an alternative for these treatment needs and which can also be used for profitable metal recovery, particularly in cases where conventional metal winning techniques are not economical. The BioSulphide® Process is a high rate anaerobic biotechnology for on-site production of H2S from sulphur species, although for smaller flows and metal loadings, the use of chemical sulphide reagent might be more cost effective. Both new projects and existing commercial operations, used for removal and/or recovery of copper, nickel, and zinc, and which range in sulphide generating capacity from 50 kg/day to 3.7 tonnes/day, are discussed. Particular focus is placed on the results of operations at the Raglan Mine in Northern Quebec where dissolved nickel is removed from contaminated water at a high efficiency through the precipitation of nickel sulphide. Plant effluent is discharged directly to the receiving environment and the high-grade nickel sulphide product is combined with the nickel flotation concentrate produced at the mine. The plant at Raglan will replace the existing conventional water treatment plant and will eliminate the need for on-site storage of treatment plant sludge.INTRODUCTIONThe BioSulphide® Process, which produces low cost H2S for use in selective metal precipitation, offers a low capital cost alternative which can operate efficiently and cost-effectively within a wide range of flows and solution grades. Since the technology can be used to recover metals from solutions with low flows and metal grades, the technology is also applicable to environmental applications for water treatment, with the sale of recovered metals providing an offset to treatment costs. For environmental control, the technology has a distinct advantage in being able to meet strict effluent discharge criteria due to the very low solubility of metal sulphides. To date, BioteQ Environmental Technologies has designed and constructed three plants for metal sulphide precipitation, with another three projects in the advanced development stage."

Jan 1, 2006

By J. E. Nesset

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

By C B. McCampbell, R W. Jr Bickes

Sandia National Laboratories has developed a semiconductor bridge (SCB) igniter for the ignition of a variety of explosive materials. When subjected to a low-energy current pulse, the bridge bursts into a plasma causing rapid ignition of the explosive material pressed against the bridge. Despite the low energies required for ignition, SCB components have proven to be explosively safe, meeting both no-fire and electrostatic discharge (ESD) safety requirements.

Jan 1, 1991

By H. Aykul

The choice of which mining method to use at many large surface coal mines is often dicated by what machinery is available or what experience the mine management can offer. One of the most significant surface coal mines in Turkey is owned and operated by the Turkish National Coal Board, located to the west of the city of Kütahya. The Seyitömer Lignite Enterprise (SLE) extracts low quality coal, the majority of which is supplied to an adjacent power station. The coal seems at SLE contain bands of ash which under normal mining conditions are extracted with the coal. This increases the ash content of the run of mine coal and results in lower efficiency at the power station and financial penalties for SLE. In this paper, therefore, selection of the best possible equipment and production method was identified to achieve high selective mining at SLE. The research found that two different high selective mining methods were suitable for selective excavation of the B3 seam, which were hydraulic excavator and truck and surface miner and truck combinations. It was also found that high selective excavation could provide the desired coal quality at 52% lower costs when the whole process (excavation, transportation, processing, etc.) was considered. Keywords: coal mining, surface mining, selective mining.

Jan 1, 2007

By Valerio Viti

In High Pressure Die Casting a molten metal is injected through a thin gate into the cast cavity. High injection pressures and high gate velocities create atomization phenomena which can negatively affect the final quality of the cast. In order to control atomization process it is essential to understand the atomization patterns and the two-phase flowfield that exist at the gate exit. In the present work, 2D numerical simulations of the flow of molten Magnesium through a high aspect-ratio rectangular gate are performed using a water analogue for an open and closed cavity. The numerical simulations made use of VOF-type (Eulerian) physical models and Lagrangian models. Further, a sub-grid scale model was implemented that, in conjunction with VOF-type equations can efficiently predict the general atomization pattern without the need for high-resolution grids. The numerical results were compared to experimental data for validation.

Jan 1, 2006

By Patrick Polk

For many years, sulfuric acid producers all over the world have been forced to meet ever more strict environmental regulations to reduce SO2 emissions. The sulfuric acid industry has implemented new solutions in order to comply with the new lower SO2 emissions target. Haldor Topsoe (Topsoe) has responded to this challenge by continuously improving the range of VK sulfuric acid catalysts and providing tailor-made catalyst solutions to meet the demands of the sulfuric acid producers for lower SO2 emissions. Reducing emissions through catalysis: requires less capital than installing a scrubber, requires no additional process chemicals, generates no waste or by-product to dispose of. In 1996 Topsoe introduced VK69, a cesium-promoted vanadium catalyst, designed for operation in the pass(es) after the intermediate absorption tower in double absorption plants. The high activity of VK69 allows for a more than 50% reduction in SO2 emissions from existing double-absorption plants. Topsoe currently has more than 110 installations of VK69. To comply with the still more stringent regulations being placed on the sulfuric acid industry to lower SO2 emissions, Topsoe has developed a new sulfuric acid catalyst designated VK-701 LEAP5™. This catalyst was introduced to the market in 2010. VK-701 LEAP5™ is based on a novel technology which circumvents the internal transport deficiencies of existing commercial sulfuric acid catalysts and thereby offers exceptionally high activity in strong, SO3 rich gases. Sulfuric acid plants have used this catalyst to meet emissions requirements lower than previously believed possible with a catalyst only solution. This paper will present examples on how to reduce emissions by implementing a tailor-made catalyst solution using VK69 and VK-701 LEAP5™.

Jan 1, 2014

By Ángel Cabello Victoria

El presente trabajo es un estudio técnico-económico del yacimiento minero Caridad, perteneciente a la compañía del mismo nombre en Lima, cuyas características permiten aplicar el método de corte y relleno en la minería en vetas de plata. Sin embargo, las bajas cotizaciones en el mercado mundial de los metales, minimizaron los costos de los mismos y aumentaron la productividad para mantener la mina en operación. Por tal motivo, se busca utilizar este método en pequeñas minas de plata que tienen características similares y asi recuperar el minado completo de los valores en plata, la eficiencia en la mecanización de los equipos de acarreo y volteo y reducir los accidentes por caídas de rocas, como causa principal en la minería subterránea.

Nov 8, 1982

By Graham Davis

The future of the world's minerals industries is often painted as bleak. Peter Drucker has repeatedly proposed that the demand for minerals has become "uncoupled" from world economic growth.' This implies that, while mineral demand was in the past linked to the growing demand for and consumption of goods and services, further world development will not require substantial mineral inputs. Lester Thurow noted that for these reasons the US minerals industry is diminishing in scale and economic importance.2 There is some documented evidence of such uncoupling, and the demand for minerals may indeed diminish in the future. But such announcements are, to this point, no more than speculation. For instance, is it not just as likely that renewed environmental concerns will cause increased demand for the relatively innocuous environmental properties of metals, replacing plastics? And even if the prophesied demand decreases do occur, a sufficient fall in metal prices due to technological advances could increase the quantity of minerals demanded above current levels, in spite of leftward shifting demand curves. Thus, worldwide mineral production activity may increase or decrease in the future and no one can say whether more or fewer of the earth's citizens will become involved in the extraction and processing of minerals.

Jan 1, 1994

By Mike Robotham

When RFQ?s are received they often contain detailed technical specifications which suggest a departure from the suppliers own customary approach to the design. Both client and end user are quite rightly influenced by their own experiences. The question is who is right, the client and his consultant, the supplier or perhaps a combination of these. This paper looks at some of the fundamental variances that often occur in the approach to the mechanical design of drum hoists, based on our experiences of recent years. Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2011

By M Armstrong, S J. Coward, A Galli

Mine management is often expected to make rapid evaluation decisions at different stages of projects based on limited and uncertain data. The challenge is exacerbated by having to distil technical complexity into a financial model that is usually designed to produce only one or two key indicators, eg net present value (NPV), internal rate of return (IRR). Mining is a complex environment with many sources of uncertainty ranging from sampling to economics. In order to optimise investment decision-making, an appropriately structured evaluation framework must be utilised. An evaluation framework should be designed to encapsulate and integrate the complexity across the evaluation cycle, ie sampling, resource estimation, mine planning and treatment, and financial and economic modelling. This complexity is diverse and ranges from sampling support, scale effects to understanding the impact of variability, uncertainty and flexibility on operational efficiency and economic viability. These complexities, combined with time and capital constraints, usually do not allow all facets of evaluation to be integrated into the model. The model must strike a balance between simplified estimation techniques and sufficient incorporation of aspects of the project that will make a material difference to the investment decision. This paper demonstrates the impact of the scale of measurement on the valuation of a mineral project. Comparisons are made between global estimation averages using a top-down approach and local estimates using a bottom-up approach. Three sampling campaigns were conducted on a virtual orebody to compare the relative NPV accuracies. Stochastic forward models were run on foreign exchange rates and are compared with the results from a fixed foreign exchange rate model.

Jan 1, 2006

By Felipe Perissé Duarte Lopes

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of curaua fibers were evaluated. Tensile specimens with up to 35% in volume of long, continuous and aligned curaua fibers were room temperature tested in an Instron machine. The fracture was analyzed by SEM. The results showed significant changes in the mechanical properties with the amount of curaua fibers. This was compared to other bend-tested composites with distinct matrices. The fracture analysis revealed a weak fiber/matrix interface, which could be responsible for the comparatively low performance of some properties.

Jan 1, 2010

By R. Biss

"Niobium or columbium, as usually called in North America is becoming a more and more important metal in the industrial world because of its attractive properties.Eventhough discovered in the early nineteenth century, it was not until the 1930's that its use became more widespread. The discovery of large commercial deposits in the late 1950's and the demand of industry for steel with high strength and toughness further promoted its use. To assure its adequate supply new or-e processinr technologies had to be developed. So, beside the traditional gravity concentration, the flotation process was employed for the partial upgrading of pyrochlore concentrate at S8ve (Norway) plant in 1953. The flotation process was equally used at St-Lawrence Columbium plant in the province of Quebec, Canada. The new plants at Araxa and Catalao in Brazil and at St-Honore, Canada, which supply almost of all niobium used today in the non-Communist world, also adopted the flotation process. The processes using long chain aliphatic rnonoarnines, diamines or sulfonates as collectors proved to be difficult especially on weathered types of ores or on those having a substantial content of silicate gangue minerals. They almost completely failed in case of alkaline intrusive rocks as syenites, nepheline syenite, ijolites and pyroxenites, composed almost entirely of silicate minerals. A lot of effort was devoted all around the world on research of new, more efficient flotation processes. So in 1982, Les Services T.M.G. Inc. (Niobec), sole producer of pyrochlore concentrate in North America, developed the direct pyrochlore flotation process from carbonatites. In 1983, at about the same time, the Quebec Department of Natural Resources Laboratories and Les Services T.M.G. Inc. announced a successful recovery of niobium Minera1s from a low grade nenheline syenite ore."

Jan 1, 1984

Modelling and simulation are important aspects of flotation research, which may assist in the design of new circuits and the optimisation of existing ones. Flotation research in the AMIRA P9 project has developed a methodology for flotation plant modelling based on determination of cell (pulp) characteristics. froth characteristics, and ore floatability (using floatability components). The implementation of this methodology requires the determination of ore floatability, to which end a small flotation pilot plant known as the Floatability Characterisation Test Rig (FCTR) has been designed and then built and kindly made available to the AMIRA P9 project by Baker Process. The FCTR has a 2 tph capacity and consists of six 130 litre rougher/scavenger cells and six 50 litre cleaner/recleaner cells. The Mintek FloatStar pulp level control system is used to control the pulp level in all cells. A number of experimental procedures have been developed for using the FCTR to obtain the data required for the P9 flotation models. These procedures include how to determine the floatability parameters, Pi and mi, the bubble surface area flux, Sb, the mean residence of the pulp in the cell, t, water recovery. Rw, froth zone recovery, Rf, and the degree of entrainment, ENT. The flexibility of the FCTR allows it to be used in numerous flotation studies such as stream characterisation, reagent testing, grinding experiments, power studies, oxidation studies, and scale-up and simulation studies. This paper will describe the design and operation of the FCTR and the procedures that will be used to obtain data from the rig for modelling purposes.

Jan 1, 2000

By Harry W. Campbell

A mineral survey conducted by the U.S. Bureau of Mines in 1983 identified no mineral resources in the Beaver Meadows, Blind Horse Creek, Chute Mountain, Deep Creek/Battle Creek, and North Fork of Sun River Wilderness Study Areas (WSA's). A prospect east of the Beaver Meadows WSA has low potential for lead resources. Sand, gravel, and limestone occurrences are numerous in the WSA's; however, similar or better quality materials outside the areas are abundant and more accessible to potential markets. Impure coal and titaniferous-magnetite occurrences are near the WSA's, but are not known to occur within these areas. In 1983, there were 7,025 acres leased for oil and gas within the five WSA's; no current mining claims were in or near any of the WSA's. Evidence of mining activity was found at only one prospect in the WSA's. It is inside the Deep Creek/Battle Creek WSA; no resources or resource potential were identified at this prospect.

Jan 1, 1984

Real Time and In Situ Measurement of Elemental Composition Using Lasers

Sep 13, 2010