Search Documents

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN'm). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

By Kenneth Trelewicz

This report describes the total effort that went into developing environmental test criteria for general mine instrumentation. The project was a two-phase effort. Phase I consisted of research and mine visits to develop an environmental profile for mine instrumentation. The profile was translated into general requirements and then into test requirements. A review of existing government and commercial specifications was performed to determine if they matched mine instrumentation test requirements. Finally, a set of environmental test procedures was developed for the testing of mine instrumentation. Phase II consisted of selecting and purchasing sample mine instrumentation and subjecting them to the previously developed tests. The purpose was twofold: (1) to evaluate the criteria developed for use as an instrumentation test document and (2) to determine the effects of the various criteria on a representative sample of both proven and newly developed instrumentation. The test criteria were then modified, based on the results of the testing, and are listed therein.

Jan 1, 1981

Table A-1. Number of underground coal mines and samples collected for underground occupations, 1988-92 [ ]

Jan 1, 1997

By Z. Sun

Imposing a strong magnetic field is considered to be an attractive method to prepare materials with aligned or textured structures due to its intrinsic properties, e.g. non-contact and easily controllable. However, the nature of the strong magnetic field effect still remains unclear and further research is needed. In the present paper, the effect of a strong magnetic field on the solidification of a hypereutectic Al-Cu alloy was investigated. After magnetic field treatment, the primary phase was aligned parallel to the magnetic field direction. Meanwhile, the eutectic micro-structural constituent became elongated and thinner. A theoretical analysis was conducted to have a better understanding of the phenomena. During solidification, the magnetic Faraday and dipole-dipole interaction forces are considered to decrease the solute pile-up in front of the solid-liquid interface and modify the eutectic cell formation. The alignment of the phase is due to the shape magnetic anisotropy and crystal magnetic anisotropy.

Jan 1, 2010

By Paul Mulcey

El presente texto señala los usos de la antracita en la industria del cemento, refinerías de azúcar, fábricas de vidrio, fundiciones y las aplicaciones inyectadas (gas de síntesis, plantas de energía, planta de laminación en Chimbote y los estudios en combustiones y aplicaciones. La formación de estos yacimiento se debe a que la mayor parte de la oxidación parcial ele s ulfurn dr\ hidl'ógeno de origen Yolcánico,con la PXCPpc ión dt> los yarimienfos ele Pinra y Ba~·oyar Pll que apar·pnf.Pme nlc Sf' nncnc•nt ra como producto r es idual dPI ¡wlrólPo.

Jul 1, 1956

By Jack L. Taylor

As expected from similar crystal structures and favorable atomic size factors, titanium, vanadium, and molybdenum are completely soluble in one another above the transformation temperature of titanium. The fl phase parameters of the continuous solid solution are shown graphically. Limiting compositions for retained fl phase have been determined. VANADIUM and molybdenum both have body-centered-cubic structures at all temperatures and, from the atomic diameter comparison factor, 3.9 pct, would be expected to form a complete series of solid solutions. The existence of complete solubility has been confirmed by work' at the Jet Propulsion Laboratory. Furthermore, vanadium and molybdenum have favorable atomic size factors to form complete binary solid solutions with the B phase, high temperature form of titanium, which also has body-centered-cubic structure. Pietro-kowsky and Duwez' and Hansen et al." have established the existence of the complete series of solutions in these binary systems. It would be logical, therefore, to expect that p-titanium, vanadium, and molybdenum would be completely soluble in one

Jan 1, 1957

By Leon Maday, Robert Robinson, Judy Cochran, Don Davis

Over the past 20 years, several soft-ground tunnels have been successfully completed in the Seattle area. These tunnels were built using design-bid-build contracting methods, and have benefited from advancing technologies in exploration, design and construction methods. Owners have utilized various contractual means to share some of the risks that are inherent to tunneling projects. This has helped to foster a competitive bidding environment and to resolve issues related to unanticipated underground conditions in a fair manner. This paper presents case histories of tunnels constructed by King County and the Washington Dept. of Transportation that illustrate a common approach to design and construction issues. The common thread is successful project completion with minor cost changes under the design-bid-build contracting method. Lessons learned from these projects are being applied to the upcoming King County Brightwater Project tunnels, Sound Transit’s Light “Link” Rail tunnels and other tunnel projects.

Jan 1, 2005

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1982 (October 1, 1980 -September 30, 1981) under its Minerals Health and Safety Technology program. Contingencies may require that a significant port ion of the program be deferred into fiscal year 1983. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the systems technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By Terry S. Cory

This report is a comprehensive summary of the results of the propagation measurements program conducted for the US Bureau of Mines under Contract H0366028. Data was gathered in the MF frequency range from a cross sample of six mines representative of the industry having typical wireless requirements. From the raw data which was gathered, a logical method of data reduction is presented which culminates in a set of average attenuation characteristics for all mines visited. These characteristics define a typical MF wireless system when the communication range requirements are known. Direct through-the-earth propagation and the range enhancement mechanism due to coupling on and off conductors are evaluated and related to the planning of a typical wireless MF communications system.

Jan 1, 1977

By Thierry Bernard, Jean Marc Laboz

This paper explains why and how integration of EIS (Electronic Initiation System) with dedicated software tools can increase benefits to blasters and at the same time simplify the design of blast sequence

Jan 1, 2000

By S. Makni, A. Faucher, F. Robichaud, A. Bouajila

"Optimizing the ball charge in a grinding mill may be needed to maximise throughput or alternatively, to achieve proper product size in more challenging situations. Efforts to optimise the ball charge however are essentially empirical and suffer from the lack of appropriate, accessible and reliable tools. To address these limitations, a new model-based technology was developed that relies on 3D Discrete Element Method and population balance techniques: it takes on the form of a simulator that aims to significantly decrease the time required to optimise the size distribution and the grinding media load within a ball mill. This paper summarizes the research work related to the development of this simulator. The calibration of the different constituting sub-models will be highlighted. The successful use of the simulator to predict the effect of ball make-up on the grinding product size distribution in one plant is also reported.INTRODUCTION Adjusting the characteristics of the grinding media charge in grinding mills holds significant potential for optimisation of mill performance. For example, properly adjusting the ball size distribution in a ball mill can help achieving specified targets for final product size distribution and/or throughput capacity. However, several problems appear when reviewing the process and the available tools to optimise ball mill load: • The current empirical simulation tools are lacking with regard to the ability to predict the performance of grinding when changes to mill ball make-up are made; • Generally, these tools estimate the top size of the charge so it is difficult to predict the effect of mixed ball make-up; • As the quality of prediction of these tools is low, the operators try to optimise the ball charge by a ""trial and error"" method and proceeding with conservative changes. The influence of these changes on grinding performance is often less than the measurement precision and the improvements then remain imperceptible; • A change in ball make-up may require an average of about 6 months waiting period before reaching the stationary state of mill ball load. This exercise is due to be costly if applied change decreases the mill performance. In its effort towards the comminution process optimisation, COREM R&D portfolio had addressed the herein described opportunity during the last five years This paper describes the technology already developed for the optimisation of ball charge. It takes on the form of a simulator that aims to predict the evolution of the grinding media load, the grinding energy available in the ball mill and the final product size distribution. The simulator was first validated in a pilot scale ball mill and then applied in an industrial case."

Jan 1, 2012

By Richard Frentress, Dave Donelon, Robert Henderson, Mike Warnert

"The Round Mountain gold mine is an open-pit mining operation located 97 kilometres north of Tonopah in Nye County, Nevada. Gold has been produced from the property since 1906.Gold is currently recovered using a combination of four independent processing operations. These include a 10,000 ton per day mill, a 30,000 ton per day, crushed ore heap leach, a 150,000 ton per day, run-of-mine ore heap leach and a small high-grade gravity concentration circuit. In 2002, Round Mountain Gold Corporation produced 755,494 troy ounces of gold at a total direct operating cost of US$2.14 per ton ($193/oz).This paper presents a summary of the Round Mountain operations and discusses some of the processing innovations that have enabled the mine to profitably recover gold from a large low-grade ore body.INTRODUCTIONRound Mountain Gold Corporation is a 50/50 joint venture between Kinross Gold Corporation and Barrick Gold Corporation. Kinross acquired its ownership interest in the Round Mountain mine upon completion of combination with Echo Bay on January 31, 2003. The joint venture partners continue to support an aggressive exploration program in the vicinity of the mine in order to add reserves and extend the mine life.The Round Mountain mine currently operates a conventional open pit that is approximately 8,200 feet long, 4,900 feet wide and 980 feet deep. Mining is conducted on 34-metre benches by electric shovels and front-end loaders paired with 150, 190 and 240-ton haul trucks. Blasthole samples are collected and assayed and provide the control for ore segregation. Based upon these assays, blasted pit rock is determined to be run-of-mine Dedicated Pad ore, crushed Reusable Pad ore, high-grade ore or waste.Gold is recovered using a combination of four independent processing operations. These include run-of-mine ore heap leaching (Dedicated Pad), crushed ore heap leaching (Reusable Pad), milling and the gravity concentration circuit. Non-mineralised rock is delivered directly to the waste dumps. Low-grade ore is trucked directly to the Dedicated Pad and medium-grade ore is crushed and placed on the Reusable Pad. High-grade ore is handled in one of three ways: 1) leached on the Reusable Pad and offloaded to the mill; 2) sent directly to the gravity plant with tails reporting to the mill; or 3) sent directly to the mill or mill stockpile. The gold particle size distribution of highgrade ore determines the processing method."

Jan 1, 2005

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By Rachel Santos Mendes

O objetivo deste trabalho foi analisar o refinamento da liga Al AA1070 deformada via ECAP (Equal Channel Angular Pressing) pela rota A em dois passes consecutivos. O material foi prensado a frio e a deformação verdadeira acumulada foi de 2,38. A caracterização microestrutural foi realizada com o auxílio da técnica de MEV. E a evolução da textura foi analisada através da técnica EBSD. A avaliação do comportamento mecânico da amostra foi realizada através do ensaio de microdureza de Vickers. Os resultados mostraram uma intensa redução no tamanho de grão após o 1º passe, seguido de um decréscimo considerável no 2º passe. A orientação encontrada na textura inicial evoluiu de {1 1 0} para {5 13 1} após o 2º passe. O comportamento mecânico apresentou um estado estacionário entre o 1º e 2º passe devido à ocorrência do fenômeno de recuperação dinâmica. Concluiu-se que um refinamento considerável foi obtido.

Aug 8, 2018

By M. D. Max, A. H. Johnson

INTRODUCTION Gas hydrates have considerable potential to be a major energy resource owing to their apparent abundance in Arctic regions and along continental margins throughout the world (Kvenvolden, 1988). Yet, the oil and gas industry has been slow to pursue this opportunity. The primary reasons for this are the large conventional reserve base for natural gas worldwide and the perception that gas hydrate will not be a viable resource for another twenty or thirty years. Gas hydrates are thus viewed as a potential resource for the distant future, but not a valid investment for the near term. This paper addresses both global gas markets and gas hydrate technology, and shows that the commercial development of gas hydrate could proceed rapidly enough to constitute a near-term energy resource. GLOBAL GAS MARKETS The proven worldwide reserves of conventional natural gas are truly enormous, totaling over 6,000 TCF according to BP (2004). Moreover, those reserves have nearly doubled during the past two decades and now represent 67 years of consumption at the current production rates of 80 TCF per year (Fig. 1). This reserve increase has occurred even as global production of natural gas has increased by 67% during the same two decades (Fig. 2). While declining conventional gas reserves are a concern in North America, especially in regions where established infrastructure exists to bring gas to consumers, large new discoveries continue to be made elsewhere in the world. Indeed, in many parts of the world (such as the Middle East and parts of West Africa), natural gas has been regarded as an essentially worthless byproduct of oil production or exists in stranded gas fields. Given this situation, pursuing unconventional gas resources that are inherently riskier exploration targets and more expensive to produce would appear to have little rationale from a business standpoint.

Jan 1, 2006

Mining is an inherently risky business; from the technical, environmental, social, and economic uncertainties associated with advancing an exploration prospect to a viable project to the operating, market, and safety risks and uncertainties attached to a developed mine. Since we cannot totally escape the risk and uncertainty related to resource projects, as an industry we should improve our presentation of the upside and downside risks in the context of the project?s development path and maturity. More transparent, consistent, and balanced views of technical confidence will better inform both internal and external stakeholders about the expected risk in the project. International reporting codes set out the minimum standards, recommendations, and guidelines for public reporting of Exploration Results, Mineral Resources, and Mineral Reserves. However, the reporting code principles of transparency and materiality are largely subject to the interpretation of the competent person(s), which may introduce a degree of subjectivity in reporting, particularly the level of disclosure regarding supporting information. It is fundamental that Mineral Resources, Mineral Reserves, and study outcomes are reported so as to unambiguously present the level of inherent technical uncertainty (or confidence) in a project, while conveying a balanced view of the opportunities a project presents. Reporting needs to consider various stakeholders who may rely on this information, and present the data in the context of the changing risk profile associated with project development paths and project maturity. This paper discusses the interdependence of resource-to-reserve conversion, the consideration of various technical-economic study types, and the level of confidence conveyed to stakeholders relying on these technical reports and other company public announcements.

Jan 1, 2014