Search Documents

By J. W. Thompson

OIL AND GAS AS MINERALS. Oil and gas within the ground are minerals and the fact that they have attributes not common to other minerals because of their fugitive nature or vagrant habit, and the disposition to percolate, and the possibility of their escape from beneath one part of the surface to another, does not remove them from the class of minerals. Texas Co. v. Daugherty (Texas), 176 Southwestern, 717, p. 719, May, 1915. OWNERSHIP OF TAILINGS-ABANDONMENT. A corporation engaged in milling- and the reduction of ores deposited the tailings therefrom upon a portion of its own land lying in a gulch through which water flows at times in great volumes and with great force' and notwithstanding all reasonable efforts by dams and otherwise to retain its tailings, the tailings eventually were forced upon the lands of an adjoining owner; these tailings were valuable and their retreatment, intended by the mill owner, profitable; and the fact that the tailings were so washed down upon the lands of the adjoining owner and permitted to accumulate and remain for some considerable time is not sufficient to show an abandonment on the part of the owner of the tailings, where it is clear that the owner had no intention of so doing, but on the contrary, always intended to conserve and retreat the tailings.

Jan 1, 1916

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By Donald Giroux

This report documents the design, fabrication, testing, and coal mine demonstration of a hopper-feeder-bolter during a four-phase program for the U.S. Bureau of Mines. The machine was designed to increase productivity and safety in under-ground room-and-pillar mining. It performed well as a hopper-feeder for continuous haulage during a coal mine demonstration. Testing in a simulated mine showed that the machine also has good roof bolting capability.

Jan 1, 1987

By John P. Capp

Information is summarized on the major uses of fly ash and prospects for utilization in agriculture and in brick and mineral-wool manufacture. Technological aspects of utilization are discussed and references are given to the work of many of the leaders in the fields of fly ash production, processing, and utilization.

Jan 1, 1970

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

By Lívia Lopes de Oliveira Goulart

A prática de escória espumante ganhou o mundo dos fornos elétricos a arco por apresentar muitas vantagens, dentre elas a redução das perdas térmicas do arco elétrico para o ambiente, reduzindo o consumo de energia elétrica e também permitindo uma maior recuperação do metal perdido em forma de FeO para a escória através da reversão feita com a injeção de C. No entanto, a eficiência das escórias espumantes produzidas atualmente ainda é tema de estudo para aqueles que querem melhorar a eficiência do processo, a vida do equipamento e reduzir custos de elaboração. Assim, esse trabalho tem como objetivo otimizar as propriedades da escória através do ajuste da saturação em MgO, melhorando a eficiência da escória espumante e reduzindo a perda de Fe sob a forma de FeO. O resultado das alterações realizadas foram ganho de energia elétrica medido e redução da perda de rendimento metálico do FEA, obtida comparando o peso produzido e o esperado pela carga metálica.

Oct 30, 2017

By Philip W. Holland

This Bureau of Mines report discusses the results of three independent reconnaissance geochemical surveys conducted in the vicinity of the Bush Dome reservoir in the Bureau-owned Cliffside field near Amarillo, Tex. The surveys consisted of (1) determining the helium content of area ground waters, (2) determining the helium content of area soil gases and ground waters, and (3) determining the helium content of soil gases collected on a grid sampling pat- tern in the Cliffside field area. The native natural gas in the Cliffside field contains about 1.8 percent helium. To date, approximately 54 billion cubic feet of gas containing approximately 39 billion cubic feet of helium has been injected into the center of the Bush Dome structure. The research work, which was completed under contracts, was done to determine if helium concentration levels in ground water and soil gas could he used as an indication of the presence of helium in a subsurface natural gas accumulation. Results of the surveys were positive in that helium-in-water and helium-in- soil-gas anomalies were detected in portions of the Cliffside field area. All helium analyses were performed by mass spectrometric techniques.

Jan 1, 1979

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

By Manuel Álvarez Alvino

El presente trabajo señala el uso de las herramientas tecnológicas en los productos informáticos para controlar las operaciones mineras, dado que no existe un un producto concebido a la medida de cada operación ya que cada realidad es distinta de la otra, tanto en el detalle de la operación como en el aspecto administrativo. En este sentido, es importante la implementación de estos recursos, el control de la gestión, como en el de los estándares de los productos utilizados.

Jul 31, 2003

By Gloyd M. Wiles

The property of the Park City Consolidated Mines Co. is situated in the northeast part of the Park City dining district 1 mile east of the town of Park City. The elevation at the collar of No. 1 shaft is 7,250 feet. Park City is a town of approximately 4,500 population lying about 30 miles east of Salt Lake City. The two are connected by an oiled State Highway, which is cleared of snow in winter and maintained in first-class con¬dition by the State throughout the year. The district is served by branches of the Denver & Rio Grande Western and Union Pacific Railroads, each operating on a daily' schedule, except Sunday. These two railroads have constructed 1 ½ miles of joint track from the town to the Park City Consolidated Mines Co. loading tipple, located 200 feet from the portal of the adit that leads to No. 1 shaft.

Jan 1, 1936

By Donald O. Capstick

A mineral survey of a 5,700-acre portion of the 11,510-acre Upper Deep Creek Wilderness Study Area (ID-111-44B) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1985. No mining claims have been located, no minerals have been produced, and no resources have been identified in the study area. Three reconnaissance samples of alluvium from the Deep Creek drainage contained $0.21, $0.22, and $2.72 per cubic yard in placer gold, higher than usual for the Owyhee River canyonland area. The samples of near-surface material contained very fine gold in values too low to support large-volume commercial placer operations, but the quantity and size of the particles of gold in the alluvium is expected to increase near bedrock. Consequently, the area may be a target for recreational as well as small commercial suction dredge operations. The physical characteristics of the individual pieces of gold (bright and angular) indicate that it may have recently come from an unidentified nearby source.

Jan 1, 1986

1.0 Control House (DWG. NO. 56-401-G) - 1.1 Physical Description The Control House is a single story, 2728 square foot building with an adjacent transformer yard. A four foot overhang provides shade protection for the walls. The building is heated and air conditioned. The HVAC System has an elevated outside air intake and provides a positive pressure environment within the structure in order to prevent the infiltration of heavier-than-air, noxious gases. The materials of construction are as follows: Structure : Light-Gage Metal Framing Exterior Walls :Outside - Preformed, Metal Siding :Inside - Insulated Metal Liner Panels Interior Partitions :Gypsum Board over Light-Gage Metal Framing Roof :Insulated, Preformed Metal Panels Ceilings :Mechanical & Electrical Rooms - Exposed underside of Roof Panels Control Room, Lunch Room, Toilets, Entry - Suspended Acoustical Lay-In Tile Floors :Mechanical & Electrical Rooms - Concrete Slab on Grade Control Room, Lunch Room, Toilets, Entry - Resilient Tile Exterior Doorsand Windows :Preformed Metal Panel Manufacturer's Standard Units

Jan 1, 1979

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987

By D. V. Roberts

Approximately 800 private consulting engineering firms in America specialize in geotechnical engineering. The gross income from these firms totals about $500 to $600 million per year. Sixty-five to seventy-five percent of this geotechnical work is per­formed by consulting engineers that belong to the Association of Soil and Foundation Engineers (ASFE). This paper presents statistics concerning the business activities and functions provided by ASFE member firms. The procedures used in typical projects are described. The paper concludes with a summary of major trends which are impacting the American geotechnical practice today.

Jan 1, 2010

To be able to continuously monitor the noise to which underground workers are exposed as a better way to help prevent hearing damage. The Approach: The Bureau of Mines has developed a Time-Resolved Audio Dosimeter which can be worn by miners to record noise level every 30 seconds and store It in a miniature solid state memory. Figure 1 is a photo of the dosimeter. [ ] How It Works: Acoustical noise is picked up by a micro-phone and fed to a sound level meter which produces a d-c voltage proportional to the A-weighted sound pressure level. (As specified by federal regulations, the A-weighted sound pres-sure level approximates the response of the ear by discounting the higher and lower frequency components of the noise.) This d-c voltage controls an oscillator which, together with related circuitry, produces a pulse train having a frequency that's proportional to the noise level.

Jan 1, 1975

By Enrique Alomia

Actualmente las organizaciones generan grandes cantidades de información que es necesario contar con un sistema diseñado manejable para anticiparse a los problemas que puedan suscitarse. Por ello, se creó un sistema de reportes de producción ((SRP) que provea información confiable y oportuna para la toma de decisiones. En ese sentido, el presente texto señala los beneficios del Sistema de Reportes de Producción (SRP) en el manejo de las organizaciones empresariales, de forma que provee a la Alta Dirección de SPCC, un medio de consulta con información de producción de forma consolidada de las diferentes unidades operativas de SPCC y permite recopilar, clasificar, procesar, interpretar y resumir cantidades de datos que facilitan la toma de decisiones oportunas y eficientes.

Sep 19, 2006

By A. M. Childs, R. F. Mather, K. R. Rawling

"The challenges encountered in the design and construction of mines and their process facilities today are becoming more intense and the engineering more competitive. The need to incorporate new techno1ogy to compensate for ever rising costs is always present, but its application in the harsh environment of Northern Canada increasingly requires the inclusion of new proven methods and innovative approaches to arrive at economically attractive projects.This paper deals with the development of the process design for the Cullaton Lake Gold Mine in the Northwest Territories. Particular emphasis is given to the interaction of the imposed construction and testwork schedules, and their effect on certain process decisions.The challenge that faced the project team may be defined by the following factors:1. A schedule which required that metallurgical testing, engineering, and procurement and delivery of all equipment and construction supplies should be complete within a period of ten months.2. Transportation of all personnel, equipment and supplies to the site by airlift, as no road was available or affordable.3. A six week period when transportation to the site was impossible.4. The extremes of temperature beyond the tree line in the Northwest Territories.5. A complete lack of infrastructure in the area."

Jan 1, 1983

By J. D. Steenkamp

Southern Africa has a history rich in the pyrometallurgical processing of ores. Two of the alloys produced are high-carbon ferromanganese (74?83 per cent Mn) and silicomanganese (59?67 per cent Mn and 14?31 per cent Si). The largest land-based manganese ore deposit in the world is based in the Northern Cape Province of South Africa. In 2010, 6.3 Mt of ore from the deposit was exported, mainly to China, Norway, Japan, and India, and an estimated 1.1 Mt beneficiated locally to produce manganese ferroalloys. In southern Africa the producers of manganese ferroalloys are Metalloys and Assmang, and of silicomanganese Transalloys, Mogale Alloys, and Match Corporation. Submerged arc furnace technology is utilized in the production of high-carbon ferromanganese (HCFeMn) and silicomanganese, applying the discard slag practice in both instances. The carbon content of HCFeMn is reduced using converter technology and that of SiMn using the Perrin process. Ninety per cent of the world?s manganese ferroalloys production is consumed by the steel industry. The consumption (and production) of manganese ferroalloys therefore closely follows worldwide steel production. From 2001 to 2010, the doubling of the worldwide production of manganese ferroalloys can be attributed to an increase in production capacity in Asia and Oceania, with the largest increase in the production of SiMn. Manganese ferroalloys produced in Asia and Oceania are mainly for the local market, with North America, Europe, Russia, and Turkey the major markets for alloys from southern Africa. The major challenges faced by the southern African manganese ferroalloy producers are increasing electricity tariffs and productivity of labour, which require a concerted effort by all parties involved to achieve a satisfactory solution. Keywords manganese ferroalloys, ferromanganese, silicomanganese, southern Africa, South Africa, manganese ore, high-carbon ferromanganese, refined ferromanganese, refined silicomanganese.

Aug 1, 2013

By L. A. Morely

The overall objective of the subject contract was to investigate the application, economic, and safety considerations of electrical-shock prevention techniques applied to surface and underground mines. Volume I of the four-volume final report starts by summarizing all research performed, and synopses of the three other report volumes are included. The balance of this volume concerns one major task of the contract, the protection of maintenance personnel. After specifying the scope of work for the task, electrical is defined, and needed ground-fault relay characteristics to prevent ventricular fibrillation are established. This is followed by an analysis of alternating-current systems, a comparison of these systems with respect to body currents, and the advantages and disadvantages of the various ground-fault protection techniques. An analysis of direct-current systems for off-track vehicles is then covered. These analyses form the basis for the research recommendations which along with suggestions for future research, conclude the report volume.

Jan 1, 1982

By Rafael Lopes

Os aços utilizados na fabricação do vergalhão CA50 conforme norma NBR7480 são usados em todo o Brasil. A grande aplicação deste tipo de produto é na indústria de construção civil em função de sua excelente resistência mecânica e soldabilidade. Estas características permitem o avanço na construção de grandes empreendimentos. Em 2009, a Votorantim Siderurgia na sua Unidade de Resende, iniciou a produção do vergalhão CA50 em escala, procurando aumentar a sua participação no mercado de construção civil. Foi identificada uma grande variação nos resultados de limite de escoamento nos ensaios de liberação de produto realizados a partir de amostras coletadas no início das bobinas de vergalhão CA50. Em função disso, foi feita a caracterização do limite de escoamento e microestrutura ao longo da bobina onde foi identificado que esta grande variação do limite de escoamento estava presente em toda a bobina. Desta forma, foram definidos os principais parâmetros do processo de laminação que poderiam estar influenciando na variação do limite de escoamento e realizado um planejamento de experimentos (DOE) para o vergalhão CA50 16,0mm, aço 1030, onde foram identificadas que a combinação da melhor distribuição da vazão de água nas Caixas d’água utilizadas no tratamento térmico de têmpera e auto revenido, somada à maior distribuição das espiras no pelo Formador e à ventilação do Stelmor no mínimo apresentaram resultados de limite de escoamento acima do mínimo especificado pela norma NBR 7480 com menor desvio padrão quando comparado aos parâmetros de processo que eram utilizados na produção do vergalhão CA50.

Oct 30, 2017