Search Documents

By Alexandre Silva Guimarães

O presente trabalho avaliou o comportamento de extração dos metais cálcio, magnésio e níquel, contidos em licores sintéticos sulfúricos, utilizando-se o extratante Cyanex 272 (0,64 mol/L) e misturas entre Cyanex 272 (0,64 mol/L) e ácido versático (0,53 mol/L). Os resultados revelaram que a adição de ácido versático ao Cyanex 272 provocou um aumento nas extrações de cálcio, que atingiram cerca de 40% em pH = 5,1, decrescendo com a elevação do pH do licor até atingir aproximadamente em 15% pH = 5,9. As extrações de níquel (em torno de 80% em pH = 7,1) foram favorecidas, enquanto as extrações de magnésio permaneceram em torno de 75-80%, numa faixa de pH entre 6,0 e 7,0, em comparação com a utilização de apenas Cyanex 272 como extratante. O níquel pode ser separado dos metais cálcio e magnésio, pela mistura dos extratantes nas concentrações estudadas, em pH = 5,1, utilizando-se de 2 a 3 estágios de contactação.

Aug 7, 2018

By M. Lombardero, J. Garcia-Guinea, J. Taboada, B. W. Roberts

The structural, textural and mineralogical properties of the slate formations of NW Spain make it the most important district in the world for quarrying roofing slates. Over the past 10 years the introduction of new methods has increased yields from 2 to 13%. The main factors affecting quality are quartz grain size less than 75 micrometres, homogeneity of slaty cleavage and S0-S1 intersection angle, very low metamorphic grade, absence of secondary foliation, beds 10-12 m thick and low content of oxidisable Fe sulphides. The two main controls on fissility are lithology and deformation accompanied by metamorphism. The minimum natural block size should be 0.6 m3 but this volume can be reduced for modern cutting tools such as diamond wire, chain and circular saws. Structural analysis is crucial in exploration and quarrying, as shown by the prospecting methodology applied at Dominio de Truchas in central Spain and the computer analysis of rock mass discontinuities at Casaio quarry

Jun 19, 1905

It has been fairly firmly established (Fisher, N. H., 1945) that the fineness of the gold in any ore deposit varies with the depth from the surface at which the deposit was formed, and, as a corollary to this, that it is dependent upon the temperature and pressure at the time of deposition. This relationship is such that, under certain conditions, the gold fineness, taken into consideration with other recognised criteria, furnishes a very sensitive and reliable guide to the relative temperature of ore formation, at least within the epithermal and the upper part of the mesothermal range.Definition of Fineness.The fineness of gold is calculated in parts per thousand and refers to the proportion of gold present in the naturally occurring metal in the lode, which is actually a gold-silver alloy, containing usually about 10 parts per thousand of base metal and up to 500 parts perthousand of silver. A clear distinction should be made between fineness and gold-silver ratio. The latter refers to the total gold and silver in the lode as determined by assay and is usually expressed as the ratio Au:Ag. Only in deposits where other silver-bearingminerals are entirely absent, which occurs comparatively rarely, can the gold-silver ratio be used as a measure of gold fineness and, in many cases, the two have no relationship. For instance, in the Edie Creek area in New Guinea, the lodes formed under shallow epithermal conditions all carry gold 500 to 550 fine, although the gold-silver ratio ranges from 1:100 to 1:1, in places in adjacent lodes.Determination of Gold Fineness.The fineness of lode gold can be determined only after it has been separated from all other minerals. Amalgamation recovers gold fairly cleanly - unless native silver is present - and the fineness of amalgam bullion is generally a reliable indication of the correct fineness of the gold. If the use of plates is involved, the bullion may be adulterated, but the effect of any copper, or other metal, that may have been introduced can be cancelled by assuming that the gold and silver shouJrl add up to about 990 fine, or by ignoring the base metal content altogether, which varies little in naturally-occurring gold, and in calculating for comparison purposes all fineness figures to the basis Au + Ag = 1,000.The composition of bullion obtained from cyanidation is generally intermediate between the true gold fineness and the total gold-silver proportion as determined by assay of mine or mill-head samples of Cyanide solution dissolves other silver-bearing minerals and the fineness of the resulting bullion is thereby lowered. Consequently, the fineness of cyanide bullion rarely corresponds to the true gold fineness and is useless for diagnostic purposes, although it is a common fallacy to refer to the fineness of cyanide bullion as the fineness of the gold.

Jan 1, 1950

By Luis de Montreul

El presente texto describe la mineralogía del oro que comprende sus asociaciones con otros minerales metálicos, relaciones con las gangas no metálica, granolometría, abundancia y las características textuales de los minerales. Para ello, es vital conocer la selección del método de tratamiento a emplear para obtener una óptima recuperación del oro.

May 1, 1986

By R. Larry Grayson, Joel R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. So far, environmental groups remain unconvinced and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This article presents a perspective on coal’s role in sustaining society by anchoring the message in a transparent way, including a material flow analysis, that links coal’s impacts across a range of social and environmental aspects. Past and continuing image problems In her 1994 paper, Nancy Bingham, with Caterpillar, outlined what the public thought about mining. Based on extensive interviews, the following results were found: • The public believed mining harms the environment. • The public believed mining harms people in nearby communities. • The public believed mining exploits workers. • The public believed mining has little personal benefit to the individual.

Jan 1, 2006

The objectives of this paper are two-fold. First, it will show what problems can arise when single estimated values are substituted for a distribution of values when evaluating an open pit mine project in the face of uncertainty. Secondly, it will show how the ability to deal with uncertainty and risk in mine project evaluation can have a significant impact on the ownersÆ and stakeholdersÆ investment decision-making. Here a new mine evaluation framework, the integrated valuation/ optimisation framework (named IVOF), is introduced as an alternative tool for mine project evaluation where uncertainty and risk are incorporated in the evaluation process.

Jan 1, 2009

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980

Chromium, a critical mineral for which the United States is largely dependent on foreign sources, is the subject of a new report just issued by the Interior Department's Bureau of Mines. The report is the first in a new series called "Mineral Commodity Profiles" (MCP's). Designed to give an updated review of important events affecting critical minerals, it also presents a comprehensive description of industry structure, supply-demand relationships, technology, and outlook for the future.

Jan 1, 1977

By James R. Evans

Orange County, adjacent to the populous and industrialized Los Angeles area, is the fastest growing county in California and is second only to Los Angeles County in total population (figure 1). In addition to an equable climate and a burgeoning economy, there is room in Orange County for growth and expansion. Growth over the past decade has resulted in rapid development of industrial tracts, housing areas, and shopping and commercial centers, mostly in former agricultural areas. The value of new building in 1972 was a record amount-over I billion dollars (figure 2). Problems relating to the proper direction of growth are the concern of both government and the private sector. The intelligent and efficient use of areas to be developed requires planning for the conservation and protection of the County's natural beauty and for the orderly development of natural resources. The availability of sand and gravel, which is used in many phases of construction, will be a major controlling factor in the future of the County.

Jan 1, 1974

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002

The Stawell Goldfield, the westernmost of the main Victorian fields, has produced over a million and a quarter ounces of gold from one and three-quarter million tons of ore. The lodes are quartz reefs and sulphide bodies occurring in sediments of lower Ordovician or upper Cambrian age. The lodes are confined to a relatively narrow suite of weak rocks lying between stronger ones above and below and there is a definite relationship between fold structure, pitch and strength of folding and ore.LOCATION HISTORY AND PAST PRODUCTIONThe town of Stawell, situated 150 miles north-westerly from Melbourne on the main railway and road to Adelaide, is the most westerly of the main gold areas of Victoria. Alluvial gold was found at Pleasant Creek (now Stawell West) in 1853 and the usual "rush" followed. Numerous alluvial leads, some surface, others buried under up to 100 ft. of Tertiary sediments were worked. The alluvial gold was soon exhausted, but in 1857 gold-bearing reefs were found on the slopes of a prominent ridge on the northern edgeof the present town. Early reef mining was by small working parties mining to shallow depths only and treating their ore at public crushing plants. Some of the early returns were very high grade. The next stage was the amalgamation of claims and the formation of companies, with their own treatment plants. This stage continued till the last mine closed in 1921. These companies had, by present standards, small holdings and far too many shafts were sunk, resulting in less efficient prospecting and operation.Since 1921 there have been one or two small scale attempts to revive mining but without success. Of recent years Gold...

Jan 1, 1960

By D. Leeb

El presente texto describe el principio de ensayo de dureza para los materiales metálicos, el cual se basa en lanzar un cuerpo móvil con una energía constante contra la probeta en reposo, produciéndose un rebote. La medida de la energía que aún queda en el cuerpo (energía residual) después del rebote es una medida de dureza. Dicho proceso comprende tres etapas: disparo, choque y rebote. En la fase de disparo, la energía potencial del cuerpo móvil se transformará en energía cinética por caída libre o por distensión de un muelle y el cuerpo móvil choca contra la probeta, a la velocidad de choque. El proceso de choque propiamente dicho se verifica en dos períodos: comprensión y restitución. Finalmente, en la fase de rebote, la energía cinética existente en el cuerpo móvil se vuelve a transformar en la energía potencial correspondiente a la magnitud del recorrido de rebote, es decir, a la altura o recorrido máximos de rebote

Mar 1, 1983

By J. Reed

The RockWorks EarthApps represent a free collection of 74 geology-related programs that read data from a built-in datasheet and create diagrams within Google Earth. EarthApps also includes programs that extract data from Google Earth. The programs that create diagrams include: point mapping (e.g. borehole locations), proportionally scaled icons (e.g. geochemistry), and strike & dip symbols. Line mapping utilities include; polylines, parabolas and pipelines. Polygon mapping programs include; thematic mapping (e.g. geology), mining claims, and public land survey sections. Image overlay capabilities include; draping (e.g. geologic maps) and time-based animations. Vertical image display capabilities are centered on either midpoints (e.g. drill-hole logs) or stretched between endpoints (e.g. cross-sections). The Flyover programs create virtual tours for site presentations. The cell-mapping includes a variety of algorithms (e.g. geochemical and geophysical contouring). Survey programs convert and export survey data to Google Earth as points and polygons. Programs that extract data from Google Earth include; points, lineations, polylines, and polygons. The RockWorks/EarthApps collection is developed by RockWare Incorporated based in Golden, Colorado.

Feb 27, 2013

By Enrique Monge

El presente texto señala las plantas de tratamiento mecánico de acero, así como las plantas de rodamiento para barras y planchas semiterminadas, las de rodamiento para la producción de barras comerciales, la producción de formas estructurales en la industría del acero en los Estados Unidos de Norteamérica.

Jan 1, 1958

By Joseph Yancik

El presente texto señala el método de evaluación que determine el sistema óptimo de los explosivos de una voladura. Los componentes básicos para una voladura óptima son: características de la roca, planificación de la mina, preparación, manipuleo, equipo de procesado y sistema de explosivos. Es preciso anotar que el punto óptimo de una voladura no está constituído por un grupo estático de condiciones. Si consideramos que los costos de perforación y disparo representan una parte significativa del costo total de la operación de minado, no es posible ignorar avances tecnológicos que ofrecen substanciales reducciones en el costo. Em este sentido, el sistema de potencia de campo, se plantea como el sistema adecuado para la predicción rendimiento de un explosivo a través de la determinación de su potencia, "in situ" bajo condiciones indicadas.

Jan 1, 1971

By Jesus Layten, Marcos Garayar

Los RPAS (Remotely Piloted Aircraft Systems, por sus siglas en inglés) o drones son aeronaves (plataformas) que vuelan sin tripulación de manera automatizada, a las que se les puede adaptar diversos tipos de sensores. Esta tecnología nos brinda la posibilidad de obtener imágenes de alta calidad y precisión, de manera eficiente, confiable, segura y de menor costo. Asimismo, permite realizar trabajos en zonas de difícil acceso, ya sea por razones geográficas o sociales. El desarrollo de los trabajos con drones involucra una serie de procedimientos y técnicas que se abordarán en el presente trabajo, junto con ejemplos de levantamientos exitosos realizados en proyectos mineros y de infraestructura en Perú.

Sep 20, 2019

By Herman Halupka

El presente texto describe los progresos alcanzados durante los cinco años de operación de dos hornos en la fabricación de pelets que desarrolló la mina Marcona a través del sistema de parrilla deslizante, patente Dravo-Lurg. Asimismo, se señala os procesos empleados para fabricar pelets como: molienda y concentración, filtración, bolas verdes, endurecimiento, y la preparación del concentrado de mineral de hierro para ser peletizado.

Jul 1, 1969

By Ralph B. Stevens

The objective of the Automatic Fire Sensing and Suppression Systems for Mobile Mining Equipment program is to document the design, fabrication, factory testing, 11-month in-mine testing, and final demonstrations of auto¬matic fire protection systems on several units of mobile mining equipment including trucks, front-end loaders, cranes, draglines, coal haulers, and cutters. Proper sealing of all system components from the elements, especially in corrosive mine conditions, is essential for reasonable life-cycles with minimum maintenance. Also, adequate power supplies, wire, connectors, and plumbing with adequate protection from the harsh mine environments and physical damage were necessary during the in-mine tests. The fire protection systems were developed from technology employed during two previous Bureau of Mines contracts: HO122053, Improved Sensors and Fire Sensing Systems for Mining Equipment, and H0232059, Validation Testing of Truck Fire Protection Systems.

Jan 1, 1978

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By George M. Robles

Dado que la máquina de flotación ha sido aceptada por la industria minera, el uso de la celda de flotación de volumen ofrece mayores ventajas y beneficios en tanto que el tonelaje a tratar va aumentando. En este sentido, el objeto del texto señala los beneficios de las celdas con mayor volumen individual en máquinas de flotación puesto que suministra suficiente cantidad de burbujas finamente dispersas que se adecúan a las partículas deseadas. Asimismo mantiene un espacio que lo separa de la especie flotable del resto de la pulpa y evita la atracción material inerte una vez que se forme la capa de espuma.

Nov 8, 1982