Search Documents

Overcasts are indispensible ventilation control devices to permit one airway to pass over another without mixing in room and pillar coal mining. The airflow distribution inside the overcast depends on its spe-cific configuration at which the flow enters into it. This study uses 3D numerical simulation to examine the pressure and velocity distributions inside an overcast. The effects of the overcast angle on the flow field are also examined. The flow is assumed to be turbulent and isothermal and the standard k-e model is utilized. Simulated results display flow separation and recirculation regions of different sizes occurring not only upstream and downstream from the overcast but also inside it. The results also show that the size of the recirculation regions in-creased with the increase in the angle before and after the overcast influencing significantly the flow field and pressure losses. The stream-lines are plotted to show the 3D structure of the flow field. The results from the simulation can guide overcast design commonly used in un-derground coal mines. Keywords: 3-D simulation, Overcast, Room and Pillar, Turbulence, Recirculation Region

Feb 27, 2013

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By P. Schilizzi, A. Jarosz, M. Karmis

This paper is concerned with subsidence prediction methods and in particular with two techniques, one based on profile functions and the other on influence functions. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. In more detail, the hyperbolic tangent profile function, as developed by VPI&SU from field data pertaining to the eastern U.S. coalfields, and an influence function method currently being adapted for the same region, are presented and discussed. The applicability, advantages and limitations of these techniques are examined and comparisons are presented with field measurements. Computer software developed for the application of these prediction methods, for two widely used personal computer systems, are also discussed and a number of examples are presented demonstrating the potential of such programs.

Jan 1, 1986

By Alencar de Andrade Soares

Este trabalho tem como objetivo descrever as ações que foram tomadas pela TKCSA com o objetivo de restabelecer a capacidade operacional plena do Gasômetro (BFG), pela sua estabilidade e, por conseguinte a sua continuidade operacional. Desde seu start-up, ambos os Gasômetros apresentaram vários problemas que impediram sua operação em plena capacidade; provocaram várias paradas para realinhamento, rebalanceamento, bem como repopeamento. Estas ocorrências interferiram fortemente na Geração de energia do complexo, devido a instabilidade dos Gasômetros, causada por irregular movimentação do pistão, provocando sua descentralização e desnivelamentos fora das tolerâncias aceitáveis, o que levou a TKCSA a limitar a operação dos Gasômetros e, mesmo assim ; sempre que descentralizava e ou desnivelava, era necessário novos ajustes (repopeamento e rebalanceamento). Tais eventos nestes importantes equipamentos, levaram a CSA a tomar várias ações conforme preconiza o IGEM (Instituition of Gas Engineer) passando por reparos estruturais e culminando com a troca do sistema de selagem dos Gasômetros.

Sep 25, 2017

By I. Liebman

Two triggered barrier systems and several extinguishing agents were tested against coal dust explosion propagating in the main entry of the Bureau of Mines Experimental Mine at Bruceton, Pa. One system used a high-pressure cylinder to propel the extinguishant; the second system used pressurized nitro-gas or Halon 1301 (CF3Br) in a low-pressure system to power the disperser. The relative efficiencies of the extinguishants were determined by compar¬ing calculated concentrations of the extinguishant clouds present in the mine during suppressing of the explosions. Results showed the following trend of increasing effectiveness: Purple-K (KHC03)<water<hybrids consisting of foam or water combined with Halon 1301<Halon alone. On a weight basis, water was two to three times as efficient as Purple-K, whereas the hybrids and Halon alone were only marginally superior to water. Maximum efficiency of an extinguishant is attained by high rates of discharge from the barrier and by minimizing the time interval between onset of discharge and flame arrival to that necessary for discharge. Both the high- and low-pressure barrier systems were demonstrated to be capable of suppressing coal dust explosions; however, because of the potential hazard of the former, the low-pressure system is considered to be the most attractive prototype.

Jan 1, 1979

By Antônio Peres, Rogério Guimaraes, Lauro Takata, Harold Wyslouzil

"Serrana’s concentrator, in Araxii, has capacity of producing approximately 800,000 tomes of phosphate rock per year, with a P205 grade of 36%, from ores grading between 13% and 14% P205. The annual mining rate is around 3.5 Mt and the apatite is concentrated according to the following sequence: crushing, grinding, desliming, flotation and low and high intensity magnetic separations.Two industrial flotation columns (3.0 m x 4.5 m x 14.5 m) were commissioned in 1993 as a replacement for circuits of barite and apatite fines flotation. In 1994, four additional flotation columns of the same dimensions were put into operation, replacing 42 Wemco mechanical cells (300 ft3 each), in the barite pre-flotation, coarse apatite (two columns) and tailings regrind flotation Circuits. Overall, 66 mechanical cells (300 ft3 each) were replaced by only six flotation columns, designed by Cominco Engineering Services Ltd - CESL.The present paper describes the stages of process development, pilot plant testwork and implementation of the industrial project, highlighting the most relevant aspects of each of them. The results achieved are related to improvements in flotation selectivity, gains in P205 recovery and better process control, resulting in better quality products and lower production costs. Other benefits included a decrease in flotation reagents, electrical energy and maintenance materials consumption. These factors contributed to a significant decrease in the cost of phosphate rock production at Serrana, in Araxa - M G."

Jan 1, 1999

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob.

By M. Schmidt, P. Nord, M. Larinkari

Cathode stripping machine technology has been developed significantly both in electrorefining (ER) and electrowinning (EW) applications in the last ten years. The main driver has been robotic cathode handling, which has enabled increased flexibility to meet different layout and material handling requirements for both ER and EW processes. Additionally, cathode stripping stations have been continuously developed to optimize speed and to reduce mechanical stress of permanent cathodes. 'taco' type cathodes have been proven as beneficial approach for high capacity operations (particularly in Cu ER), where over 600 cathodes per hour continuous throughput has been achieved. However, the latest developments also apply to split type cathode stripping. Besides material handling, the modern cathode stripping machine has also an important role to provide information for production and quality monitoring. This paper describes the latest developments from the field of copper cathode stripping based on several different projects implemented in the recent years. INTRODUCTION After introduction of the permanent cathode technology in the late 1970s, it became the prevailing technology in copper refineries over the traditional starting sheet process by the end of 1980s. The main driver was less labour-intensive production due to fewer processing steps required along with more automated electrode handling equipment (cathode stripping machine, anode preparation machine, anode scrap washing machine and tankhouse cranes). Since then the design of the cathode stripping machine has followed the development of permanent cathode technology. The main development steps so far can be summarized as follows: Full Deposit Stripping Machine (FDSM) based on waxed permanent cathodes or cathodes with bottom edge strips resulting in split cathodes (copper sheets separated, see Figure 1) Wax less cathode stripping based on V-groove on bottom of the edge strip resulting in either ‘taco’ cathodes (enveloped copper sheets, see Figure 1) or split cathodes Full Deposit Robotic Stripping Machines (FDRSM) using 1–5 robots for permanent cathode handling and cathode stacking.

Jan 1, 2019

A201 aluminium alloy is a high strength casting alloy with a nominal composition of Al-4.6Cu-0.3Mg-0.6Ag. It is strengthened by the O(Al2Cu) phase and the ??(Al2Cu) phase during heat treatment. Further strengthening of this alloy system can be obtained through the addition of transition elements, but care must be taken as other elements might have adverse effects on the mechanical properties. The objective of this study is to determine the influence of Mn on the tensile properties of rheo-processed Al-Cu-Mg-Ag alloy A201. ThermoCalc software was used to predict the different phases that can be expected in the alloys, and scanning electron microscopy(SEM) with energy dispersive spectroscopy (EDS) was used to investigate the actual phases that formed. The influence of these phases on tensile properties is quantified. SEM and ThermoCalc revealed that there is an increased amount of the Al20Cu2Mn3 with increasing Mn. The tensile properties showed that high amounts of Mn do have adverse effects on the tensile properties of alloy A201, especially the ductility. Keywords Semi-solid metal (SSM) forming, alloy A201, intermetallics, Al20Cu2Mn3

Jan 1, 2011

By Julio Villon

Actualmente en las técnicas de trabajo de minería es frecuente el uso de tecnologías como la teleoperación, telecomunicación, capacidad computacional masiva, redes de información, bases de datos más poderosas, etc. Por ello, es necesario considerar que el éxito en la implementación está relacionado al proceso de adopción, los requerimientos de capacitación y el manejo del cambio. En ese sentido, el presente texto señala la importancia de la integración tecnológica en la minería para mejorar la productividad y la gestión de los activos. La actividad minera debe ser enfocada como una cadena de valor que tiene diferentes procesos alineados con la estrategia y los objetivos de la empresa. Dichas definiciones van a reflejar la manera cómo la empresa decide relacionarse con su entorno: accionistas, clientes, proveedores, trabajadores, estado, comunidad. Los procesos se traducen a nivel de secuencias de actividades y de ejecución de estas definiciones.

Sep 19, 2006

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By Lance A. Roberts

Expansive soil formations can be found throughout the United States. When subjected to wetting, these formations have the potential to swell and exert large uplift forces on buildings and foundations. Lightly loaded structures, such as single family residences founded in areas of expansive soils, can be significantly damaged due to uplift movement from swelling actions. Designing an economical deep foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material or the use of drilled shafts can be costly. Piles made from recycled polymer materials could provide a solution. Due to a lower coefficient of friction along the interface of the soil-pile interface compared to traditional pile materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure, which minimizes the risk of significant structural damage from excessive movements. This paper presents the results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity. The remaining four piles were subjected to long-term monitoring of uplift movement during the course of the project. A concrete anchor was also installed at the test site for uplift monitoring. Data gathered during the field and laboratory testing was utilized in a non-linear soil-structure interaction model to predict the displacement behavior and internal stresses within a plastic pile and concrete anchor subjected to uplift forces from the swelling shale. While more research is needed to further understand the application for recycled plastic piles, the results from this research indicate that their use is a viable alternative for support of lightly loaded structures in expansive soil environments.

Jan 1, 2010

Marble deposits of dolomitic variety are available in large quantities in India and for extracting these deposits diamond wire saw cutting machine is mainly used. Cutting performance of the diamond wire saw machine depends on rock parameters, machine parameters and operational parameters. Rock parameters related to physico-mechanical properties, such as, compressive strength, tensile strength, shear strength, modulus of elasticity and abrasion resistance of marble play role in determining cutting rate and beads wear rate. Thus, this study was undertaken to determine the relationship between different physico-mechanical properties and cutting performance. This work also aimed at enhancing the cutting performance of diamond wire saw in dolomitic marble deposit. Study was conducted in the field at three different zones having deposit of soft, medium hard and hard dolomitic marble. During the study, cutting rates and wearing of diamond beads were recorded in the field. Physico-mechanical properties were determined in the laboratory. The results obtained were subsequently evaluated by using statistical analysis. Study revealed that these properties of marble play a significant role in the performance of diamond wire saw machine. Predictive equations for the wearing of diamond beads and cutting rate were developed based on regression models. Results of this study will be of ample use for operators of wire saw to achieve maximum cutting performance and for manufacturers in designing the diamond beads.

Dec 6, 2010

By K. Lombard

"‘Roof support awaiting time’ (RSAT) is a term used at Goedehoop Colliery’s Simunye Shaft to describe the potential production time lost due to the continuous miner (CM) standing idle waiting for roof support to catch up. Investigations revealed that in 2013, Simunye Shaft had approximately1400 hours of RSAT, which suggests that the mine could have potentially produced an additional 280 000 t of coal. This project consisted of two parts. Firstly, the causes of the high RSAT and means to improve the situation were investigated. Secondly, as insisted by mine management, the CM cutting sequence was investigated as a possible cause of high RSAT. Machine-related challenges due to the roofbolter installing support too slowly, geological conditions (mostly hard roof conditions and slips),logistical challenges pertaining to the CM cutting sequence, man-related challenges related to operator fatigue, re-support, operator inexperience, and the absence of support targets were identified as main contributors to RSAT. Furthermore, results showed that the roofbolters in the sections at Simunye Shaft are slower than the CMs. A target of 28% reduction in RSAT was set. Experts from Kennametal and Fletcher were consulted to find solutions for the identified causes. In total, eight solutions for RSAT were identified, but the solution that contributed most significantly to reducing RSAT was to use hard roof drill bits as a standard product at Simunye Shaft. Calculations showed that by using hard roof drill bits, RSAT can be reduced by 43%, which is more than the specified 28% target. The cutting sequences at Kriel, Greenside, and Simunye Shaft, togetherwith three newly developed cutting sequences, were simulated using the UCMS (Underground Coal Mining Simulation) program. A re-aligningprinciple was incorporated into the newly developed cutting sequences toalign the cutting sequences to general support work and to reduce RSAT. A decision matrix revealed that a cutting sequence in which boxing takesplace in R3 (third road to the right of the belt road) and in which the re-aligning principle has been incorporated will be the best option for Simunye Shaft. The recommended cutting sequence will lead to a 5% increase in production.The work presented in this paper was carried out as partial fullfilment for the degree BEng (Mining Engineering)"

Jan 1, 2015

By Andrew G. Martin

In 1991, Modular Mining Systems began marketing a Slope Monitoring System (SMS) now installed at twelve mines. The SMS uses automated wire line extensometers to monitor field conditions frequently. Every few minutes, the slope displacement values and current temperature are transmitted to a central computer via a packet radio telemetry system. The desktop workstation receiving the data continuously provides updated displays of active slope monitors and generates audible and visual alarms if movement exceeds user specified thresholds. The computer system also generates numerous graphs and reports for quick analysis of slope stability. This work describes the functionality of the SMS, details improvements to the SMS hardware and software developed for several clients, outlines different installation techniques needed for wall rock and spoil monitoring, and interprets slope movement data using illustrations of stable and unstable conditions.

Jan 1, 1996

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By Richard Pizzi

Built in 1806, Boston&apos;s African Meeting House is the oldest surviving Black church building in the country. A $7 million dollar renovation was begun in 2006 to restore this historic building to its 1855 appearance and to modernize the building&apos;s accessibility, electrical and mechanical systems. As part of the restoration, an underground utility room and elevator tower, needed to provide handicap access to the Meeting House, were constructed. Extending up to 17 feet below the foundations of the abutting buildings, the utility room was constructed within one foot of some of Boston&apos;s oldest and most expensive residences. All equipment and materials had to enter the work area through a narrow alley rendering conventional methods of excavation and construction of earth support using heavy equipment unfeasible. A unique combination of micropiles, structural cap beam, internal struts and shotcrete facing was designed and constructed to provide the permanent and temporary support of the lateral loads from the earth pressures and adjacent building surcharges and the vertical loads from the elevator tower. The narrow and congested streets of the Beacon Hill neighborhood presented many day-to-day challenges for the contractor.

Jan 1, 2011

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979