Search Documents

By C. A. Rhoades

The spillage that accumulates under conveyor belt lines presents a possible fire and explosion hazard fomiinqjetsoruiel, especially to those who must clean up the spillage. The U.S. Bureau of Mines conducted research to reduce this hazard by identifying and investigating the parameters affecting the efficiency of conveyor belt cleaning. The amount of material carried back under the conveyor and the wear rates of metal cleaning blades decreased with increasing blade-to-belt pressure to a limiting value, after which the carryback and wear rates remained essentially constant. The optimum blade-to-belt pressure was found to be 11 to 14 psi for the research conveyor system. Greater pressures increased the blade-belt friction without improving either cleaning or blade life. The modes of blade wear were three-body abrasion and slurry erosion caused by the sand-lime test mixture. Wear rates were reduced by increasing the metal hardness, opti-mizing the pressure, and removing conveyor belt imperfections. Corrosion was not observed to affect the wear of various steels in tests of less than 34 h. The results of this study should allow mine operators to run their conveyors under conditions that will maximize cleaning and minimize equipment wear.

Jan 1, 1989

By Stefan Aronsson, K. Rainer Massarsch

"ABSTRACT The geology of Sweden is characterized by the most recent glacial period with deposition of very soft clays and loose sand. Due to these difficult geotechnical conditions, new, innovative foundation and ground improvement methods were developed, which today are used in many other countries. Over centuries, Swedish scientists and engineers have made important contributions to the developments in foundation engineering. An important aspect of the success of Swedish foundation engineering in practice is the spirit of close cooperation between practitioners, engineers, and scientists. This has been achieved by the establishing of commissions, with the aim of finding solution of geotechnical problems. The paper focuses on developments in foundation engineering during the last century and does cover present activities in Sweden.IntroductionSoil mechanics and geotechnical engineering play an important role in Swedish society, as most construction activities require the consideration of foundation conditions. The objective of the paper is to summarize important developments in foundation engineering, primarily during the past century, which have influenced geotechnical engineering also in other countries. These achievements are the result of contributions by scientists, engineers and practitioners, only a few of which can be named. The paper does not claim to cover all aspects of geotechnical engineering, as emphasis is on the solution of foundation engineering problems from an international perspective. Thus, ongoing or recent research and development projects and activities within the geotechnical community are not included, as this would exceed the scope of the paper.Over the centuries, Swedish scientists and engineers contributed to the development of civil and foundation engineering. One important reason is the geology of Sweden, which is characterized by the most recent glacial period, resulting in the deposition of soft clays and loose sands in the coastal areas and dense glacial till in the interior of the country. Geotechnical engineering in Sweden has a long tradition and early contributions by several Swedish engineers and scientists have had a profound influence on the current foundation design in and beyond Sweden. A description of early Swedish geotechnical engineering has been presented in several publications by Flodin and Broms (1981), Broms and Flodin (1988), Massarsch and Fellenius (2012). The historic development of Swedish geotechnical and foundation engineering can be divided into four periods. During the “Early Era”, engineers were active in different sectors of military, civil, and mining engineering. Next, the “Industrial Era” comprised developments during the industrial revolution, when the transportation infrastructure of the country was modernized and extended. During the third period, possibly the “Golden era” of Swedish geotechnical engineering, which started at the end of the 19th century and lasted the following fifty years, geologists, engineers and scientists helped to establish modern geotechnical engineering. But also during the recent past, the “Modern Era”, several important contributions to geotechnical and foundation engineering which originated in Sweden, are used in many countries today."

Jan 1, 2014

A hard lump char containing only 4 to 5 per cent ash, 0·25-0·30 per cent sulphur and a trace of phosphorus has been produced from Latrobe Valley brown coal by slow drying and carbonization of ordinary industrial briquettes at temperatures between 7000 C and 14000 C. The briquette char can be made with a variety of reactivities by varying the maximum temperature of carbonization; the higher the temperature, the lower the reactivity. The strength of the fuel compares favourably with metallurgical coke made from black coal, though it may not be quite so resistant to abrasion. Experiments in a small experimental cupola indicate that it will make a satisfactory fuel for use in iron foundries. It may also find extensive application as a smokeless fuel in other branches of industry and in household heating appliances.INTRODUCTIONVictoria, like South Australia and Western Australia, is apparently without 'significant deposits of black coal of coking quality but there are huge reserves of brown coal of high moisture content (60-66 per cent) in the Latrobe Valley (well over 20,000 million tons have been proved) and there are other important deposits in the south central portion of the State (Herman, 1952).For three decades Victorian industries, including a few metallurgical firms, have been using the briquettes made at the Yallourn factory of the State Electricity Commission of Victoria (S.E.C.). These briquettes, having a moisture content of about 15 per cent and a calorific value of approximately 9,500 B.T.U. per pound, are satisfactory for certain grate-type furnaces but they are not suitable for use in cupolas of other shaft furnaces because they disintegrate badly on rapid heating.

Jan 1, 1956

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

By R. O. Williams

A recent article by Chernock, Singer, Mueller, and Beck 1 which supports the use of the integral of I sin $ d$ for comparing fiber texture data does not settle what happens to I sin ø as ø approaches zero, where I is the diffraction intensity for poles oriented 0 deg from the fiber axis. They indicate that they believe that it should approach some constant value (that is, I increases without bound) and the fact that in reality it does not was a result of the diffraction

Jan 1, 1960

By R. Lincoln

A surplus of vanadium has resulted from the tremendous output of uranium, of which vanadium is a byproduct. More knowledge of the properties and characteristics of vanadium as a pure metal has been needed so that industry can take advantage of its availability and use it according to the best principles of conservation. Besides the problem of utilization, there is the ever present need of finding new materials which will satisfy specific and demanding requirements of science and engineering; vanadium or one of its alloys may possess the latent potential for filling some of these needs. Thus this? research project was undertaken by the Bureau of Mines to determine and examine some of the physical and mechanical properties of pure vanadium. A corallary investigation was the determination of the effect of the interstitial contaminants, oxygen, nitrogen, and carbon, on unalloyed vanadium. The vanadium used for these determinations was principally the product of experimental production of the Bureau. The evaluation of this material, as small quantities became available, provided most of the data that have been obtained.

Jan 1, 1962

By Javaid M. Alvi

This paper is an attempt to outline the emergence of Augered Cast-ln-Place piles as one of the more economical types of foundation for supporting high-rise buildings and heavily loaded structures recently constructed in the flood plains in and around the Greater Pittsburgh area. To understand the process of selecting foundation types, it is important to understand the general geology of the area and past construction activities that have taken place in the flood plains, especially along the riverbanks, during the last century. The first part of this paper presents a brief description of the general geology of the area; the second part of the paper concentrates on the historical evolution of the use of deep foundations and selected case histories; and the last part presents the results of load tests on large diameter Augered Tremie Concrete (ATC) Piles placed in sandy alluvium which suggests a much larger load-carrying capacity of these piles and also provides an insight into their future application. 2.0 GENERAL GEOLOGY 2.1 Soil Overburden Most of the high rise buildings in the Central Business District as well as along the North Shore and South Side of Pittsburgh are situated in the flood plain at the confluence of the Allegheny River and the Monongahela River where their combined flow forms the Ohio River. The flood plain consists of unconsolidated deposits of Quaternary age that overlie the bedrock of Pennsylvanian age. These deposits are called alluvium or valley fill, and include moderately to poorly sorted clay, silt, sand, gravel and some boulders. Their thickness varies from zero at the edges of the valley to about 80 feet towards the rivers (Figure 1).

Jan 1, 2001

By Jorge Madias

O trabalho está baseado na análise de dados de perto de 200 fornos elétricos a arco de diferente design: convencional, de corrente contínua, de carcaças gémeas, com preaquecimento de sucata no transportador ou em shaft, etc. Incluem-se fornos que processam principalmente sucata, e fornos com carregamento parcial de gusa sólido ou líquido, ferro briquetado a quente (HBI) ou ferro esponja (DRI) a frio ou a quente. São avaliados os consumos de energia elétrica, oxigênio, gás natural e materiais carbonosos; os tempos entre vazamentos, com forno ligado e com forno desligado, assim como a produtividade horária. Com os dados obtidos, se analisa a influência dos metálicos (e seu estado térmico ao momento do carregamento), e o design do forno, sobre os consumos específicos mencionados e a produtividade.

Oct 30, 2017

By Axel Doelcken

?? Liebherr excavators in standard configuration are generally designed to operate in an ambient temperature range between -12°C and +55°C (10.4 °F and 131°F). ?? To operate effectively and efficiently in very low temperatures special consideration needs to be given to the design ??An inappropriately designed hydraulic system unable to withstand extreme changes in temperatures or varying working conditions will lead to: - premature wear and more frequent replacement of components - increased maintenance & unplanned downtime This will affect productivity & operating costs.

May 1, 2008

By Edward L. McHugh, Charles Sabine, David G. Long

While less than 1% of reported mine accidents are associated with slope stability problems, slope failure accidents were responsible for about 15% of U.S. surface mine fatalities between 1995 and 2003. Small rockfalls, which may involve hand-sized rocks weighing only a few pounds, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic yards of material or more can be fatal even for heavy-equipment operators. As part of an ongoing study at the Spokane Research Laboratory, several remote sensing technologies are being evaluated as tools to assess slope stability and monitor slopes for hazards. An interferometric radar device capable of detecting very small displacements on slopes has been assembled and tested. Radar techniques can provide new tools to augment current methods for monitoring ground control hazards in mines.

By Peter Edmunds

Durante mucho tiempo, la perforación subterránea se adaptaba a la energía eléctrica. Actualmente, la transición se sufre en la perforación de la superficie. En este sentido, el presente texto describe algunos aspectos de la perforadora hidraúlica de percusión -en tanto posible perforadora del futuro. Las aplicaciones posibles de las perforadoras hidráulicas de percusión en la perforación de superficie son: la perforación de banqueo de alta producción en canteras, perforación secundaria en minas metálicas a cielo abierto, explotación de minas de carbón a cielo abierto, construcciones importantes y otras obras de ingeniería civil. Asimismo, este tipo de perforación tiene futuro donde la productividad es alta y los costos de rendimiento bajos. De otro lado, al comparar las ventajas de la energía hidráulica y la neumática en la perforación de superficie, se considera como productiva la primera -en tanto existe una mayor capacidad, un mejor ambiente laboral y unos costos de operación más bajos.

Jan 1, 1980

By James Weaver

During the past 16 years, the authors have successfully used high-capacity rock anchors installed inside open-ended pipe piles, driven to bedrock, to provide uplift and overturning resistance for various structures including piers, bridges, power plant components and commercial buildings. These systems were ultimately used on the projects due to a combination of high uplift forces or overturning moments on the structures and the relatively poor subsurface conditions present at the sites. Other, foundation systems such as rock-socketed drilled shafts and spin fin piles were considered but were found to be economically prohibitive or not technically feasible.

Jan 1, 2011

By Stefan Larsson, Sebastian Adevik, Sadek Baker, Razvan Ignat

"Abstract Uncertain strength, deformation and flow properties in dry deep mixing columns often lead to conservative choices concerning design values where the design is regularly complemented with a surcharge fill. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle. The deformation properties of a ground improvement were studied by means of two small embankment load tests. The settlement measurements were also used in FEM analyses, where the effect of surcharge on creep settlements was investigated. Based on the results, the effects of the surcharge were considered negligible and could safely be ignored. The project is an example how the contractor can use a field test as an effective design approach.IntroductionGround improvement of soft soils with dry deep mixing columns, or lime-cement columns, is often combined with a surcharge fill. The main reason for using a surcharge is to force the primary settlement and some of the secondary settlement that would have occurred under the final embankment height alone, to take place under the surcharge loading. Another reason is to level out uneven settlements. Strength and deformation properties in improved soil cannot be sufficiently assessed in advance, before columns have been tested on-site, and this uncertainty often lead to conservative choices concerning design values. In order to compensate for a slow forecasted consolidation process, the design is regularly complemented with a surcharge. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle.Extensive research undertaken by Åhnberg (2006, 2007) shows, by means of triaxial and oedometer tests, that cementation processes and a load acting on the columns during hardening, makes the improved soil to behave as a heavily over-consolidated soil due to an increase in quasi pre-consolidation pressure. The effects of using a surcharge on the time for consolidation and creep properties are thus probably small, since the stress level does not normally exceed this quasi pre-consolidation pressure. A study presented by Venda Oliveira et al. (2013) shows that the stress level within small ranges has limited effect on the creep properties.This paper presents a case study where the deformation properties of a ground improvement using dry deep mixing columns was investigated by load tests on two small test embankments. The tests were performed at the Interchange Värtan project site, which is part of the Norra länken infrastructure project in Stockholm. The tests were not performed as a research project but simple load tests performed by the contractor with the purpose of rationalizing the design delivered by the client. One purpose of the load tests was to assess the deformations when the columns are loaded temporarily by overlaying concrete works. Another purpose was to provide some input data to a study of the effects of using surcharge on creep settlements. The analysis was conducted as finite element modeling using the commercial code PLAXIS, where creep settlements can be simulated using the built-in Soft Soil Creep model."

Jan 1, 2014

By S. M. Spottiswoode, J. A. L. Napier, M. Kataka

The move away from the use of strike stabilising pillars at depth and the adoption of the more flexible system of mining towards final dip remnant pillars brings new opportunities for optimising mine design. In the initial planning stage, the size and spacing of the final pillars is designed using classical design criteria, through limiting modelled values of Energy Release Rate (ERR), Average Pillar Stress (APS) and Excess Shear Stress (ESS). In reality, mines often leave pillars that are larger than those originally designed. One of the reasons for leaving more ground is an unexpectedly high rate of seismicity. In this paper, we present developments in integration of modelling and seismicity that are aimed at developing design criteria that are more responsive to local conditions.

Jan 1, 2003

By Larry A. Lien

"A brief summary of the different membrane separation options currently available to the mining industry will be presented and discussed. The processes described involve operating membrane plants on the following applications: pregnant leach solutions (PLS) in the copper and gold industries, fractionation and concentration of metals and acids in refineries, and wastewater treatments to meet state-of-the-art surface discharge criteria.Included is a specific discussion on cost savings resulting from an operating membrane treatment system of nearly 3,500 m3/hr barren water relative to the prior, conventional precipitation practice at a major heap leach gold mine. This Engineered Membrane Separation® (EMS®) plant has produced water for six years that has met all standards for direct discharge into the environment, and captures and returns to the operation valuable minerals and solvents which were not previously being extracted in the Merrill-Crowe process.INTRODUCTIONMembrane technology has been available for more than 35 years, but has been used sparingly in the mining industry. However, recent developments in polymer chemistry, spiral-wound element design and construction, water clarification pretreatment equipment and techniques, and an expanded understanding of membrane fouling and cleaning techniques have dramatically improved the reliability and robustness of membrane-based systems for potential use by the mining industry.In the past 15 years large operating plants have successfully demonstrated the use of this “new” membrane technology to include the separation of pay-metals from large-volume acid and cyanide heap leach mining solutions containing copper, zinc, gold and silver. Moreover, variations on these same membrane technologies are ideally suited to fractionations that add value to processing fluids from refineries, like separating metals from acids or concentrating acids and producing high-quality process fluids."

Jan 1, 2010

By Reinhard Gnilsen

Soil Nail walls, like any other structure, must meet high standards of design to be acceptable to the public and owners. On the other hand, the concept of soil nailing trails behind other structures in terms of defined design criteria that are commonly acknowledged. This is not to say that soil nail walls need to be less safe or less conservative than alternative more conventional concepts. Instead, the lack of established design criteria and design methodology entails that rules of thumb from past experience, overly simplified calculation assumptions, and the engineers' common sense judgement must substitute for a complex analysis of true stability and wall performance. Those "design approaches" must be conservative to ensure an adequate structure. Also, soil nailing may not be perceived prudent where site conditions are considered beyond past experience. For instance, site conditions may be perceived out-side the scope of soil nailing applicability where walls are very high, soil parameters variable or low, or nearby buildings close to the wall edge. The latter relates in particular to deep

Jan 1, 1988

By Peter N. Calder, J. L. Workman

There are many opportunities for computers to assist in dragline mine planning. Three important areas particularly lend themselves to computer assisted study. These are overall mine design and planning, the computation and display of range diagrams and the calculation of production and production variability. The computation of range diagrams is of particular interest because of the importance of matching the dragline and site geometries. This paper examines the uses of range diagrams in dragline mining and illustrates the application of computer techniques to the computation using one such program as an example. The use of computer generated range diagrams for machine selection, pit design and in parameter analysis is discussed. Directions for further development are also provided. There is a great deal that can be done to additionally enhance the ability to provide accurate designs for the dragline operation. One area that needs special attention is the dumping of overburden around access ramps into the pit. This situation is one of the most difficult dumping sequences and affects machine selection and pit operation. It is also suggested that programs that simulate the production schedule of the drag-line would be useful. It is concluded that large overall mine planning programs are very important in dragline mining. However, smaller programs designed for a specific, task are also important tools in many cases. These are easy to learn and use, well adapted to the PC environment and provide useful information, both for design and for daily planning.

Jan 1, 1989

By Gao Dazhao

This paper presents some research results of pile foundation performance. Measurements on the bearing behaviour and driving effects of piles have been carried out during pile testing and pile driving. It has been found that the ratio of end resistance to the ultimate load depends on the pile length, and the ratio in general is less than 40% for single piles. However for pile group, the end resistance seems to be greater than skin friction. The characteristic curves of skin friction and end re­sistance appear as interaction between soils and pile. The contribution of skin friction to the pile bearing capacity not only depends on soil properties but also on the relative position of the soil layer. The pore pressure and the lateral pressure in ground have been observed during the stage of driving piles. Based on the available data, the radius of plastic region and the coefficient of pore pressure A can be found analytically. The pore pressure time process curves which may be used for practice have been predicted by means of numerical method.

Jan 1, 1991

By Fabio Da Costa Garcia Filho

Durante os processos de beneficiamento de alumina, no processo Bayer, é gerado um resíduo insolúvel denominado lama vermelha. A incorporação de resíduos industriais em cerâmica vem sendo utilizada atualmente na busca de matérias-primas alternativas, e também buscando uma destinação ambientalmente correta aos resíduos que poluem. O objetivo deste trabalho foi utilizar planejamento experimental para estudar a absorção de água em cerâmica incorporada com lama vermelha. Foram tomados pontos experimentais, cujos teores dos materiais utilizados variaram de 0 a 100%, e as formulações queimadas a 950°C. A argila verde e as misturas contendo maiores percentuais da mesma apresentaram menores valores de absorção de água e retração linear de queima. O modelo matemático que mais se ajustou foi o cúbico especial. Os resultados obtidos no planejamento de misturas mostram que para as três regiões experimentais propostas, o modelo cúbico especial foi o que mais se ajustou aos resultados reais, e que este é estatisticamente o melhor modelo matemático e deve ser usado para avaliar a absorção de água.

Oct 30, 2017

By Seokbin Lim

In the design of explosives devices, an understanding of the behavior of explosively propelled matter is one of the most important steps in maximize the performance of these devices. For instance, an explosively driven metallic liner in LSCs (Linear Shaped Charges) creates its functional effect of penetration after a finite distance of travel (before collapse), thus the detailed study of the projection mechanism of the flat liner after detonation helps in the optimization of the design of LSCs. In a typical metallic flyer driven by explosive detonation, the detonation gas propels nearby matter including flat flyers. After a certain degree of expansion in the detonation gas, the flat flyer reaches its maximum velocity and slows down afterward. These typical behaviors are well investigated and numerically studied by many researchers. However, the rarefaction intrusion (detonation gas expansion) near the surface of the explosive charge creates significant deformation of the flat flyer , and produces U-shaped bending or deformation near the edge of the flyer during projection, creating unexpected behavior in explosive devices of interest. In this paper, a preliminary investigation of a localized Ushaped deformation of flat metallic flyers during projection is studied utilizing a theoretical approach and computational modeling facilitating an understanding of a general tendency of the deformation behavior.

Jan 1, 2010