Search Documents

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

Two small coral islands in the Pacific Ocean, situated close under the equator, and formerly classed among the Line Islands, have, during the last three or four years risen into prominence owing to the valuable deposits of phosphate of lime discovered on them.The deposits of Ocean and Pleasant Islands are under the control of the Pacific Islands Company (1902) Limited, of London and, Sydney, and the high grade of the phosphate, together with the exceptionally favourable facilities for mining this mineral, of which there are several millions of tons on these islands, give this company advantages which enable them to command the Australian and New Zealand markets, and also to make large contracts with Japan and other countries. Both islands, as far as surface indications are concerned, are entirely constructed of coral, with phosphate on the top from the highest points to the present sea level, there being no sign of volcanic rocks, with the exception of a few pieces of drift pumice on the coast.Banaba (Paanopa according to. the Admiralty charts), also known as Ocean Island, was discovered in 1804. It is situated in lat. 0° 52" S. and long. 169P 3[)" E.

Jan 1, 1904

By K Pery, J Leahy

Established metallurgical plants operate in a complex environment of interdependent drivers including technology change, operating and maintenance practice, evolving markets, HSEC requirements, statutory and plant requirements, personnel turnover, ore supply, and financial conditions, to name a few. A successful optimisation program should comprehend these factors and drive towards not only lower operating costs, but also higher rates of return for a given level of investment. Optimisation programs have the potential for very high rates of return on capital that Greenfield projects rarely have. This paper presents a robust strategy and methodology for plant optimisation initiatives as well as a case study of how it was implemented at the QNI Yabulu refinery in Queensland, Australia by an integrated team of researchers, engineers and operators. The methodology is premised on the fact that nobody knows the production asset as well as the current operating team. It covers the optimisation process from ideas generation, various stages of selection against the agreed criteria, development, including testwork, funding approval and implementation. It highlights the benefits in the use of integrated teams, the establishment of a sound project basis, and a diligent, phased approach.

Jan 1, 2004

By T. Holmes

Investigations reveal that the throughput difference between a perfect production day and the average is often on the order of 40%, and that bulk solids handling system deficiencies are the largest (>50%) class of lost opportunities. Root causes for underperformance of elements in material handling systems can often be traced back to the detailed design and even study-stage oversights. To reduce or eliminate bulk solids handling problems in an existing system requires an analysis of troublesome handling equipment – for example, a concentrate transfer chute that experiences plugging, poor flow to the furnace, unacceptable dust generation, and spillage. These problems often lead to significant maintenance costs related to downtime and personnel time. Understanding the cause and cost of flow issues is the first step in troubleshooting the problem. Next, measuring the material’s flow properties is critical to providing design data required to develop a comprehensive scientific solution. In the case of a new installation, the design data is required to properly design the system right first time and prevent flow problems from occurring so that the new equipment works correctly from start-up. This paper highlights the cost of material handling problems and discusses the best approach to evaluate material handling system deficiencies. A case study is given of how Anglo American's operation in Barro Alto Brazil enjoyed a 5-month payback from a bulk solid transfer chute debottleneck project. INTRODUCTION When operating a plant or designing a greenfield or brownfield operation, the intent is to have perfect production days (PPD) each and every day. Money is made by moving material through the plant in a controlled manner to produce the desired product. Mining operations and copper concentration processes are at the most basic level a practice in bulk solids handling (BSH). Unfortunately, many of the project planning steps are overlooked, particularly related to BSH. Investigations reveal that the throughput difference between a PPD and the actual average is often on the order of 40%, and that BSH system deficiencies are the largest (>50%) class of lost opportunities (Wellwood, 2017). Root causes for underperformance of elements in material handling systems can often be traced back to the detailed design and even study-stage oversights. BSH issues are essentially baked into the fabricated plant and left to operations to accept the deficiencies and deal with them for the life of the mine. These deficiencies then become part of the normal operation of the mine and plant.

Jan 1, 2019

Vale Inco?s Coleman Mine 153 Orebody is a narrow vein deposit with a dip that varies from 30 to 70 degrees. It has a strike length of 1200-feet and the current mining extends from the 4250 level to 5100 level. The primary mining method is mechanized cut-and-fill although drift-and-fill is also used in wider sections of the ore zone. The ore body is divided into six main mining horizons with an average of three mining blocks on each cut. There are some interesting rock mechanics challenges related to mining upward from the 4550 level and these challenges are increasing as the mining front progresses toward the 4400 level. The mining of the 4550 block is currently at cut 13 whereby the crown pillar thickness is approximately 60-feet. Significant factors including increased stress levels in the crown pillar, the change in the orebody dip at this level and a recently indentified geological structure in the footwall, have all combined to introduce seismic activity in the footwall of 4550 level. Closer studies revealed a consistent trend of seismicity that was further examined with core logging and Acoustic TeleViewer technology. The data from these assessment tools disclosed a geological structure that is influencing the mining environment. This paper reviews the seismic analysis for the 4550 level mining zone and the subsequent procedures used to locate the new geological structure. The paper also discusses the key mining practices used to successfully mine cut 13 of 4550 level and briefly reviews the studies that are underway to up-date the mine design for continued extraction of high-grade ore in a safe and productive manner.

May 1, 2009

By Kung-Lee Wang

This report describes the linkage of all mining sectors with all other manufacturing, services, and final demand sectors of the U.S. economy. Besides being a basic data source, it provides a framework for aggregate economic impact analysis with respect to the mining industries. The framework is an open-static input-output model specifying 48 mining industries as classified in the Standard Industrial Classification Manual for all mining activities and 76 nonmining industries which collectively exhaust, all economic activities. The 124-sector model used in this report is an expansion of the preliminary 82-industry aggregation estimates made by the Department of Commerce. In the expanded model, 48 ruining industries are substituted for the original 6. The methodology used to ascertain the industry-by-industry procurement cost estimates and product ion flows necessary to the construction and expansion of the basic 82-sector model included personal interviews, case studies of specific mining activity analysis, and published and unpublished data from the Bureau of Mines and the Census of Mineral Industries, The end products of this study are two tables arranged to show the direct purchases necessary for each industry to support the level of economic activity and the total purchases generated in each industry throughout the economy by each $1 of aggregate economic demand in 1958. The tables may he used for economic impact studies and market analysis by firms engaged in or closely associated with the mining industries. Some illustrations of their usages are presented.

Jan 1, 1967

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By Francisco Zenteno

Dado que la operación aurífera de Pierina representa uno de los costos operativos más competitivos del mundo, la minera Barrick Misquichilca trata de proporcionar un grato ambiente de trabajo para su personal, estimulando la creatividad y la polifuncionalidad en sus empleados. Por ello, nace el proyecto SIP2000 donde optimiza el sistema de información para el mantenimiento preventivo de la planta de procesos en la mina Pierina. El proyecto comprende el desarrollo de tres fases: La primera fase comprende la definición de los principales equipos críticos que podrían afectar a la producción, asímismo la implementación y estandarización de redes de comunicación entre equipos críticos para finalmente desarrollar interfaces HMI que supervisen variables relativas a Mantenimiento. La segunda fase, integra todos los sistemas de supervisión y control de planta con los sistemas de seguimiento “online” de Mantenimiento (fase 1), desarrollando un solo sistema de tratamiento y análisis de información de planta; y la tercera fase comprende la instalación y el desarrollo de aplicaciones basadas en tecnologías Cliente/Servidor con base SQL, que finalmente proporcionan la información y los medios para realizar consultas que optimizan el seguimiento y toma de decisiones relacionado al mantenimiento preventivo/predictivo.

Jul 17, 2000

By A. J. Magerowski

Energy consumption is a main component of operational costs for the comminution of mineral bearing ores. Reduction of energy consumption has continually been addressed by mill operators and equipment manufacturers. Our testing over the last few years strongly indicates that the overall energy needed to comminute a mineral bearing ore can be brought down significantly, if more work is done in the crushing stages of the comminution circuit.This calls for uprating of the conventional crushing equipment into a new generation of crushing equipment to produce finer products. This will result in the emergence of new ideas in the design and application of equipment and corrnninution circuits.

Jan 1, 1986

The Wamum and Idzan Creeks Prospect, located 79km W of Lae, Morobe Province, Papua New Guinea (PNG) was discovered by the exploration arm of Conzinc Riotinto of Australia Pty Ltd (CRAE). The detailed surface exploration and 11 vertical holes drilled by CRAE, combined with the recent work by Highlands Gold Limited, indicate the occurrence of porphyry copper-gold mineral- isation and associated alteration. The prospect occurs within andesitic volcanics of the Middle Miocene Langimar Beds. It is bounded by NE trending faults to the NW and SE. The alteration and mineral- isation is hosted in the andesitic tuffs adjacent to high level quartz diorite and hornblende diorite stocks. A NW trend to alteration and mineralisation is obvious in Wamum and Idzan Creeks. The main alteration type is propylitic with minor zones of potassic alteration. A late sericite-quartz-kaolinite-pyrite alteration overprinted the earlier alteration and mineralisation. Copper and gold mineralisation is related to a quartz-carbonate-chalcopyr-ite-pyrite (¦ bornite) vein stockwork and biotite ¦ K-feldspar alteration. The mineralisation system at Wamum and Idzan creeks is low in total sulphides. It is considered as a high- level fracture-controlled system with limited low grade Cu-Au mineralisation.

Jan 1, 1991

By Gerardo Álvarez

"Existe un proyecto en minería que está relacionado con equipos rotatorios utilizados en la molienda del mineral. Dichos equipos requieren un buen funcionamiento para el proceso productivo y monitoreo posterior de la operación. Sin embargo, cuando ocurre un mal funcionamiento, puede ser verificado mediante el rompimiento de la normalidad. En ese sentido, el presente texto describe el estudio de la factibilidad como un sistema capaz de enviar datos desde el equipo rotatorio sin necesidad de fabricarun equipo adicional para encontrar el punto que indique a qué posición corresponde cada registro. Es decir, se incorpora la tecnología Bluetooh a la transmisión de datos para el registro de la posición que está ubicado el sensor y así aprovechar las ventajas relacionadas con el registro de nivel de la señal. "

Apr 1, 2012

By David M. Jurich, Randy J. Essex, Alex de Aboitiz

An Automated People Mover (APM) transit system is planned for the growing Phoenix Sky Harbor International Airport. The APM will improve passenger movements between the terminals, and provide a link to parking facilities, a new rental car facility, and the planned metro Light Rail. The underground works will include shallow twin bored tunnels, taxiway crossings, and underground stations constructed beneath critical airport facilities. Challenging soft ground conditions will require extensive underpinning and ground improvements. Design is underway, and construction is scheduled to begin in 2007 with project completion in 2015. The owner’s planned delivery method for the APM Project will be Construction Manager at Risk (CMAR) with a Guaranteed Maximum Price.

Jan 1, 2005

By Guoqi He

Common offset seismic data collected over two active longwall panels at different stages of mining reveal that significant arrival time delays are produced in reflections from different levels within the mine cover. Mining-induced arrival time delays are also observed beyond the edges of the mine over unmined areas. Reflection arrival time delays increase with reflector depth and are laterally variable. The arrival time delays are produced by reductions of seismic velocity within the overburden. Reflection arrival time delays from a major strong unit located neutrally within the cover are proportional to subsidence, however, delays in other events are not.

Jan 1, 1989

By W. I. Watson

The study considered all the institutional, resource reserve, technological, and economic factors relevant to the industry's present and future status, such as markets and marketing techniques, competition from other producers both domestic and foreign, federal and state regulations affecting the industry, quarrying and processing technologies, slate reserves and resources, and industry structure and economics. Constraints to the growth of the industry were assessed and scenarios proposed to solve some of the problems.

Jan 1, 1980

By Juan Manuel Rivera Poma

El presente trabajo describe los métodos empleados para una buena administración y control de la fuerza laboral a través de la aplicación de técnicas en los temas de determinación de la carga de trabajo, los requerimientos del personal, distribución del personal a los requerimiento actuales de la labor y un sistema de control permanente de la fuerza laboral. En este sentido, fue CENTROMIN-PERÚ, quien realizó los análisis técnicos de los recursos humanos y costos por intermedio del Departamento de Ingeniería Industrial-División Sistemas y así mejorar la productividad y la eliminación de gastos innecesarios de la mina.

Nov 20, 1978

The projection of operating costs for mining, processing, and other site operating costs is an exercise which can be fraught with considerable peril. Not only are the physical characteristics of each mineral property unique, but a range of other factors will influence the consultant's approach to compiling cash flow estimates. This paper details some of the techniques used in estimating operating costs for use in order-of-magnitude cost studies and feasibility studies, and describes how to avoid common areas of difficulty. A series of examples relating to open pit gold mining and processing cost estimates illustrate these problems, and various corrective methods are described. The mining and treatment processes, and their associated cost elements, are followed in sequence of operation from on-going ore delineation through to disposal of the product. In addition the problem of assigning management, administration and overhead costs along with taxation allowances is addressed. Of critical importance is the application or possible misapplication of accrual procedures to the cost elements. In many cases such misapplication can introduce more pronounced errors with projects of short duration, such as the typical open pit/C.I.P. gold operation commenced in the last decade. The importance of providing verification of estimates depending upon the standard of the cost study is also investigated, and opinion is provided upon the minimum levels of verification necessary at various stages. Finally, the amalgamation of the various individual cost elements into a coherent whole is reviewed.

Jan 1, 1990

In redesigning the cyanide plant at Mount Torrens, in conjunction with Mr. L. W. Grayson, the manager, several minor alterations were introduced in order to have the operations under thorough control, and these having proved serviceable may be of sufficient interest to merit a description here. The lixiviation vats, though only 8 feet in diameter, were retained, but the pipes leading away from the bottom were reduced from two inches to half-an-inch in diameter, and had a fall to the zinc boxes of about 4 feet. As these small pipes were completely filled by the solutions fiowing away from the vats, they exerted a suction equal to their fall and thus hastened the rate of flow, so that tailings containing a larger proportion of slimes could be treated than was possible where the larger pipes were used, as, there not being sufficient fiow of solution to keep the latter filled, no suction could be obtained with them. It was found that with'most of the tailings treated a sufficient flow could be obtained from the half-inch pipes when the taps on, them were only one-third to half open. The lower end of each of these pipes was connected by means on indiarubber tubing with the sille hole of 11 in aspirator bottle, and to the mouth of this bottle a few feet of similar tubing was connected, so that the solutions coming through could be directed into either of the fixed tubes leading respectively to the waste water tank the strong solution zinc boxes or the weak solution zinc boxes.In working the vats, the following method was found to give good results. While filling the vats with tailings the taps were left open, so that the water might drain off into the waste water tank the surface of the tailings was carefully levelled. When the strong solution was run in at the top, the air contained in the interstices of the tailings was forced through the half-inch pipe at the bottom as a strong blast, instead of, as I believe js usual, escaping by means of channels formed by it through the tailings, and thus tending, it would appeal, to render the disposition of the tailings less even and to make.

By K. A. Lewandowski

Agglomeration techniques are widely used by industry to form fine particles into larger masses that are easier to handle and process. One area where agglomeration is potentially useful is in heap leaching operations. With-out agglomeration, fine particles travel through the heap, clogging the spaces between the larger particles and resulting in poor leach solution flow. Poor flow of leach solution will result in long leach rates and/or decreased metal recovery. Agglomeration immobilizes the fine particles and therefore improves heap permeability to fluid flow. Additional additives (binders) are needed to prevent agglomerates from breaking up as leaching solution percolates through the heap. Type II Portland cement and lime are two well-known binders used in gold and silver leaching, but these are limited to alkaline leaching environments. Various other products have been tested as binders, including polymers. This paper summarizes the benefits of agglomeration in heap leaching and the results obtained from the testing of several different agglomeration binders in heap leaching operations.

Jan 1, 2009

By Benjamin A. Allou

La seule production de columbo-tantalite réalisée en Côte d?Ivoire est effectuée dans les éluvions et alluvions du gisement d?Issia, localisé au Centre- Ouest de la Côte d?Ivoire. Même si un lien direct avec les roches granitiques est suspecté, aucune attention particulière n?a été accordée à l?étude de la minéralisation primaire en relation avec l?évolution des granites et des pegmatites associées. Ces granites, qui sont en intrusion dans les roches sédimentaires du Protérozoïque inférieur, comprennent : le granite orienté à deux micas (Lobo), le granite orienté à muscovite dominante (Bitapia) et le granite porphyroïde non orienté à muscovite dominante (Issia). Les résultats de cette étude indiquent que les pegmatites à Nb-Ta-Be-Li sont liées au granite de type Issia. Les observations de terrain et les analyses sur roche totale des granites montrent que: (1) les trois principaux granites de la région sont de type- S et peralumineux dans leur composition, (2) ils ont été formés pendant la période tardi- à post-Éburnéenne, (3) le granite d?Issia fut le dernier à se mettre en place. Les pegmatites liées au granite d?Issia ont été classées en quatre types : Apegmatites stériles; B- pegmatites à Be; C- pegmatites zonées à Nb-Ta-Be; et Dpegmatites zonées à Be-Nb-Ta-Li. Les pegmatites zonées comprennent les zones suivantes: I- zone à aplite; II- zone graphique; III- zone à albite, microcline, béryl et columbo-tantalite; IV - zone à microcline massive; V- zone à quartz. Ces pegmatites présentent une zone d?altération métasomatique externe. La minéralisation de Ta, Nb et Be est liées à la zone III des pegmatites de types C et D, et celle de Li est associée aux greisens qui peuvent être observés n?importe où dans les pegmatites de type D. Les données de terrain et de laboratoire indiquent que le granite d?Issia est la roche parentale des pegmatites à éléments rares de la région. Les pegmatites minéralisées sont distribuées seulement autour du granite d?Issia et les patrons des terres rares des granites et ceux des pegmatites à éléments rares sont très similaires. Les analyses de la composition totale montrent un lien génétique entre le granite d?Issia et les pegmatites à éléments rares. Il est suggéré que les pegmatites ont été formées durant le transport et la cristallisation fractionnée du magma.

May 1, 2003

By O. Schumacher

Guidelines for publication of information defining the amount and grade of resource material available in a deposit are well established in Australasia?s JORC Guidelines, Canada?s National Instrument 43-101 and similar documents in South Africa, Peru, Chile and elsewhere (Table 1). These guidelines provide standards to apply regarding the geologic and geostatistical basis for describing the level of confidence to be assumed for an estimate of the amount and grade of material. All of them provide for a strict distinction between material that has been demonstrated to be economically mineable and that which has not, and all of them provide terms such as ?resource? or ?exploration information? to be applied to data regarding material that has not been demonstrated to be economically mineable. It is not until an economic study has been completed that we are allowed to apply the powerful terms ?reserves? and ?ore? to our deposit material. Indeed, the application of these eye-catching labels immediately tells the reader that an economic study has been completed by a qualified person, and that the results of the study were positive. While extensive guidelines are established for describing the level of confidence in published geologic data, and the nature of the economic study that should be accomplished before using the terms ?reserves? or ?ore?, surprisingly little guidance is provided regarding the process to use, and the level of detail to attain, for estimating capital and operating costs for the study. The intent of this paper is to lay the groundwork for development of suitable guidelines for the cost estimating process. While the codes do not provide specific instructions for the cost estimate, they do provide numerous hints and clues to help determine the level of detail expected and the type of procedure to apply in preparing the estimate. This paper will first review the various codes to gain an insight into the thinking of the drafters of the codes regarding their unstated expectations for the cost estimating process. Based on this review, a series of guidelines are proposed for this purpose.

Feb 27, 2013