Search Documents

By V. M. Troughton

Large diameter bored piles with grouted bases have been adopted for the foundations of the majority of the buildings at Canary Wharf in London's Docklands, including a deep basement car park. The piles are founded in the Thanet Sand which forms part of London's aquifer where water levels are reported to be slowly rising. A special pile test has been carried out to determine the effects of both the basement excavation and a possible long term rise in the groundwater level on the performance of base grouted piles. These effects were simulated by injecting water around the pile toe and thus reducing the vertical effective stress. In this paper the test layout and procedures are described and the results are presented. The test results showed that the reduction in pile base resistance under increased water pressures was less than predicted by conventional design methods based on vertical effective stress. The end bearing resistance was found to be proportional to the mean effective stress.

Jan 1, 1989

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

Aurum Reef Resources is a provincially owned unlisted public company which holds a number of prospecting licences over Otago hard rock historically active minesites. The Bullendale Licence 31 1845 was applied for in 1985, granted 1991, including a DoC special condition allowing re-opening of the historic workings. The underground workings were commenced in 1862 and up to the mine's closure in 1906 some 40 000 ounces were produced at an average grade of 15.5 g Au/t. The purpose of the summer 1991 work programme was to enter the workings in an attempt to observe and sample the mullock between the lodes operated by the early miners. This objective was achieved on the third attempt. Samples were taken and subsequently a contract geologist resampled the workings and prepared a report indicating the Bullendale lode zone to be generally mineralised. Mullock interlode and schist foot-wall consistently returned assays over 0.5 g/t.

Jan 1, 1992

[1.1. The provisions of this code are minimum provisions and are designed to minimize hazards to life and property in and about underground coal mines where electrical equipment and circuits installed used. They indicate the Steps necessary in the selection, installation, operation, inspection, and maintenance of electrical equipment and circuits to obtain proper safeguards in reducing electric shock, fire, explosion and other hazards. Surface as well as underground installations were considered in formulating the code and, unless otherwise stated, each provision applies equal to both underground and surface installations. This code does not apply to buildings and installations not directly connected with mining operations, nor does apply to strip-mining operations.]

Jan 1, 1952

By Om P. Garg

The purpose of this paper is: 1) To summarize the capabilities and some of the limitations of the existing mine planning software. 2) To provide some guidelines for acquiring the software. 3) To identify problems and challenges in terms of how to justify increased use of computers (particularly the 32-bit microprocessor based super micro computers), for various activities related to a mining operation No attempt has been made to review the contents of available software packages in detail. Also the scope of this paper is limited to mine planning related computer applications. Applications related to accounting, inventory control, preventive maintenance, equipment scheduling, etc. have not been covered.

Jan 1, 1983

The trend for using larger equipment in open pit mining to achieve cost effectiveness raises the question about the optimum economic point of scale in the current world of globalization. The present paper treats this question through the prism of a new methodology of assessing the impact of the size of production equipment on the economic outcomes of coal mining ventures. The methodology incorporates a production scheduling optimization model that implements both principles of mine planning, coal quality optimization and waste deferment. The implementation of the waste deferment principle dealing with the spatial and time aspects of the mine sequence arrangement allows the adequate modeling of the optimality of production equipment scale through the use of mine investment parameters, such as, purchase and ownership costs and discounted cash flows analysis. A case study is provided to illustrate the applicability of the new methodology.

Jan 1, 2004

By G. F. Livingston, F. K. Shelton, J. C. Stahl, R. E. Churchward

"INTRODUCTION An investigation of the metallurgy of cobalt from domestic ores has been in progress since February 1940 and has resulted in the formation of a hydrometallurgleal process for the production of electrolytic cobalt metal. Previous reports of these investigations have been given by F. K. Shelton; 7/ and Ruth E. Churchwrd, F. K. Shelton, and G. Knickerbocker. 8/ Briefly, the process, as applied to ores containing cobalt oxide, consists of leaching with H2SO3 or, preferably, with H2SO3 and H2SO4, to dissolve the cobalt. The cobalt solution passes through one or more purification stages to remove iron and elements of the copper group, and cobalt carbonate is precipitated under carefully controlled pH conditions. The cobalt carbonate is dissolved in on acid electrolyte containing sulfuric acid, boric acid, and sodium fluoride. The electrolyte then proceeds to electrolytic cells where cobalt is plated as a metal and sulfuric acid is regenerated.The present paper contains the results of several investigations signed to give a more complete chemical and engineering understanding of different unit processes involved in the electrowinning of colbat. Some work has been done to broaden the process to include arseniferrous cobalt ores as well as the oxide ores upon which the investigation was initiated. Most of the data presented herein have been obtained since the release of the previous reports; any changes suggested heroin that conflict with recommendations in earlier reports are based on more complete data and usually are preferable."

Nov 1, 1945

By Mike Tracy

This section of the Handbook deals with general principles to be evaluated in the development of a mining operation. It addresses the major issues that must be examined to fully evaluate a mining venture. Of course, one of the main topics to be evaluated is mine planning, which is covered in more detail in other sections (13, 17) of the Handbook and should be referenced in mine development projects. The topics to be discussed in this introduction include equipment and supplies, infrastructure, utilities, and project management. In any of the aspects mentioned, the current existing conditions at or near the mine site must be evaluated. This will include assessment of current use of utilities, infrastructure, housing, equipment suppliers, etc., as well as anticipated growth, both in the supply aspect of these systems as well as projected usage on these systems. After full assessment of both these aspects, an evaluation must be made as to the requirements the project will place on these items. Assessment must be made as to any up-grades required to bring the project on line, what impact the project will have on existing or expanded systems, and anticipated future growth impacts on support systems not only of the project but of other surrounding industry and urban devel-opment

Jan 1, 2008

By Luciano Aparecido Kempski

O ferramental utilizado em processos de conformação é de grande interesse da Engenharia de Superfícies devido às características tribológicas específicas encontradas nestes processos. Portanto busca-se sempre melhorar o ferramental para se obter menores coeficientes de atrito, desgaste e adesão de material sobre a superfície da ferramenta, sendo empregadas diversas técnicas de tratamentos superficiais como a nitretação e os revestimentos depositados via PVD. Uma variável importante do par tribológico é o coeficiente de atrito desenvolvido entre as superfícies em contato nos processos de conformação a frio, portanto foram realizados ensaios de pino-sobre-disco e ensaios DST, para determinação de coeficientes de atrito em pares tribológicos. Desta forma, chapas de aço inoxidável austenítico AISI 304 foram conformadas sobre uma superfície de um aço ferramenta DIN X100CrMoV8-1-1, com o propósito de se conhecer o atrito desenvolvido entre os materiais. As amostras foram nitretadas a plasma e ou revestida com TiCN, posteriormente, a caracterização da microestrutura e as propriedades avaliadas através de ensaios mecânicos e tribológicos. O ensaios proporcionaram obter valores de coeficiente de atrito para as condições de tratamentos e lubrificação utilizados e as análises dos resultados mostram um aumento da dureza superficial das amostras tanto nitretadas quanto revestidas com TiCN e uma redução do coeficiente de atrito significativa quando se faz uso do revestimento.

Aug 8, 2018

By Harry Verakis, Thomas Lobb

Over the past decade, approximately 5.1 billion pounds of explosives were used annually, on average, in the United States. Most of the explosives were used by the mining industry. The coal mining industry was and still is the dominant user of explosives. About two-thirds of the explosives consumed was used in coal mining.

Jan 1, 2003

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By Fabiane Leocádia da Silva

Cristais da família cristalográfica do sal de Tutton A2B(XO4)2.6H2O, A=K, NH4, Rb, Cs, Tl, B=Mg, Mn, Fe, Co, Ni, Cu, Zn, Cd, V, Cr, X=S e Se tem sido investigados por diversas técnicas experimentais com o objetivo de compreender suas propriedades físicas e potenciais aplicações tecnológicas. Investigações sobre o comportamento estrutural têm sido realizadas por difração de raios-x a fim de compreender suas propriedades estruturais, principalmente a distorção Jahn-Teller presentes nos cristais com cromo e cobre. Soluções sólidas destes sais na forma A2B'xB”(1-x)- (SO4)2.6H2O, têm sido relativamente pouco investigadas embora possam apresentar distorção Jahn-Teller. A estrutura dos cristais desta série à temperatura ambiente é monoclínica, grupo espacial P21/a com duas moléculas por célula unitária. Bons monocristais da série (NH4)2NixCu(1-x)(SO4)2.6H2O com 0

Aug 16, 2017

By B. H. Clemmons, B. G. Saunders, R. H. Stacy

"INTRODUCTION This investigation was undertaken to determine the response of Birmingham (Alabama) red-iron ore to heavy-medium concentration. Specifically, the work involved a study of the efficiency of the process in separating coarse gangue diluents from the ore and an endeavor to evaluate the potential economic results. The investigative work was not intended, nor is it to be construed, to be adequately exhaustive in scope to enable immediate plant construction. Rather, the primary objective was to determine the grade of ore that could be produced by heavy-medium treatment and the resulting indicative or tentative benefits to be derived from such treatment. The latter, in turn, would determine the merits of the more exhaustive study that would be required for an ultimate decision on the heavy-medium treatment of the ores.The problem of avoiding excessive contamination of red-iron ores by shale and/or ferruginous sandstone has been before the operators of the iron mining industry of the Birmingham, Alabama, district for many years. Within the last two decades, increased mechanization of mining methods has increased this contamination to a considerable degree. In fact, general utilization of scraper loading and other mechanical methods of mining, in conjunction with small increases in the natural insoluble content of the ores, in some cases has actually resulted in the production of ""acid"" or excessively insoluble ore, where ""basic"" or excessively lime ores were produced formerly.The contaminating materials are derived largely from roof spells and natural parting seams in the ore, a condition that to some extent has been aggravated by the irregularity of the ore beds. The latter have been subjected to both primary and secondary folding in many places. Considerable faulting has taken place, also. In many localities these conditions render virtually impossible complete avoidance of ore contamination from the over and underlying sandstones and shales. However, in a few localities, where the ore beds are less disturbed and shale partings are absent, mining can and is being accomplished with relatively little dilution."

May 1, 1948

By Jim Truskoski, Alain Bouchard, Andy Kerr, Germain Labonté, Jim Barrett

"Improving mill grade recovery relationships is always good business. INCO’s Clarabelle Mill has just undergone a $16 million process upgrade that was designed to improve nickel recovery by 2%. The “Mill Redesign Project” was completed on time, under budget and delivered the promised improvement in recoveries.This paper describes the methodology of the Mill Redesign Team, details of the process improvements and the critical success factors that helped the team deliver on its promises.With a payback of under one year, the Mill Redesign Project will play a key role in ensuring a competitive edge as INCO embarks on its second century of operation.INTRODUCTIONIt is not uncommon in milling operations to encounter a crisis. That is the point when the process does not behave as expected and fails to respond to the increasingly desperate efforts of the metallurgists and operators. Flowsheet and process changes are attempted and abandoned. With luck, one or more of the changes achieves some mitigation of the original problem or more usually, the original cause of the problem disappears. Regardless, the metallurgist can sit back and bask in the apparent success of his or her endeavours.Less common is when a problem is carefully diagnosed, a team put together to explore all avenues and recommend a path of action that is implemented on time, on budget and immediately delivers on the promises which are sustained over time. This is one such story. It is the story of the Mill Redesign Project at INCO’s Clarabelle Mill in Copper Cliff, Ontario.BACKGROUNDThe Clarabelle Mill was built in 1971 on the southern rim of the Sudbury basin. At that time it was one of four mills operated by INCO in the Sudbury area. During the 1970’s, 80’s and 90’s, the need for increased process efficiency, higher levels of sulphur rejection to tails and the concurrent development of high capacity mills and flotation cells, resulted in the consolidation of INCO’s Sudbury area milling operations into a single, expanded facility at Clarabelle."

Jan 1, 2003

By B. J. du Plessis

Automation of the conventional grinding circuits of Palabora Mining Company (PMC) required that adequate instrumentation and a control system had to be put in place, after which extensive testing had to be done to evaluate different grinding control strategies. The objective was either to optimize the particle size from the grinding circuit, or to increase milling circuit throughput while maintaining particle size at existing levels. Prior to automation of the process as described below the circuits were controlled manually. No on-line information on cyclone feed densities, cyclone feed flow or cyclone overflow particle size was available. This type of control relied heavily on interpretation of the process parameters by the operator and on his ability to make informed decisions on what the set points should be. An integral component of the automation process was the installation of a SCADA package (SysCad SDX) for implementing the on-line control strategy. A self-correcting model for prediction of cyclone particle size was developed and implemented on the SDX. The model is calibrated using values from the particle size analysers while they are operational. If the particle size analysers choke or fail for any reason, the model continues to provide a good estimate of the particle size. This technique ensures that a continuous particle size indication is available compared to the intermittent reading from the instrument. The continuous signal allows particle size to be used as a process variable for control purposes. A strategy was developed and implemented which allows for the production of a controlled grind size from the conventional milling circuit to the flotation circuit. The grinding control strategy allows for the control of particle size from the individual cyclone overflows. This strategy allows the operator of the process to increase or decrease production rate by specifying a coarser or finer grind size required for flotation.

Jan 1, 2001

By Manuel Enrique Rodriguez Blanc

A planta industrial de produção de ferroníquel da Anglo American Barro Alto, localizada no Estado de Goiás, recebeu notificação de clientes como Aperam (Bélgica) e Acerinox (Espanha), em relação ao formato esférico apresentado pelo ferroníquel produzido. Para solucionar o problema, foi realizado teste na planta piloto da empresa de engenharia UHT para desenvolvimento de novos projetos e de nova tecnologia com objetivo de aperfeiçoar o formato do produto final. A utilização de disco de 4 canais solucionou o problema do formato esférico, no entanto, forma-se muito “bodes” ocasionando explosões. O sistema de granulação utilizando um tundish rotativo, mantem as mesmas características físicas do metal granulado com disco de 4 canais além de aumentar a segurança da operação, reduzindo os riscos de segurança do trabalho.

Oct 30, 2017

Validation and Application of Filtration Theory to Plate and Frame Pressure Filtration - From Laboratory to Full Scale

Sep 13, 2010

By Eustaquio Vieira Junior

O Alto-Forno 2 da thyssenkrupp CSA, no Rio de Janeiro, iniciou sua primeira campanha em 16 de dezembro de 2010. No decorrer de sua campanha, verificou-se problemas de deslocamento de staves de ferro fundido, deformação dos staves de cobre e desgaste acentuado do refratário do top cone. Na análise dos eventos adotou-se a inspeção por vídeo endoscopia e em seguida foram tomadas algumas ações para recuperação e preservação do Alto-Forno 2, sendo estendidas também do Alto-Forno 1. Dentre as ações de preservação dos Altos-Fornos destaca-se a projeção robotizada de material refratário, shotcrete, visando reduzir o desgaste acentuado dos staves e deterioração de suas tubulações de refrigeração. O trabalho apresenta o detalhamento das técnicas utilizadas e seleção de materiais assim como os preparativos operacionais que garantiram o bom desempenho do Alto-Forno 2 nos momentos que antecederam a parada e após seu retorno à operação, mostrando que a atividade é viável do ponto de vista técnico e financeiro.

Oct 30, 2017

By Felipe da Silva Siqueira, Mariana Sizenando Lyrio, Aline Cristine Lemos Duarte, Weslley Luiz da Silva Assis, Harison da Silva Ventura, André Luiz Moraes Alves, Paulo Rangel Rios

A nucleação nos contornos de grão é um fenômeno muito recorrente em materiais metálicos. Essa situação foi tratada por diversos autores como Cahn e Rios e Villa, usando a abordagem de nucleação em planos e linhas aleatórias. Neste trabalho estudou-se a nucleação nos contornos do polígono de Poisson-Voronoi e de uma matriz hexagonal em 2-d com métodos analíticos e simulação computacional. Utilizou-se uma equação baseada no método de Cahn para nucleação nos contornos de grão. Para nucleação nos contornos do polígono de Voronoi a equação não mostrou adequação total com os resultados simulados para dois tipos diferentes de casos, já para os contornos da matriz hexagonal, notou-se que quanto maior a quantidade de pontos sorteados na matriz, mais os resultados simulados concordaram com a equação proposta.

Nov 13, 2019

By T. E. Pogue

This paper traces the co-operative initiative undertaken by South Africa?s gold mining companies through the Chamber of Mines Research Organization (COMRO) in development of hydraulic technologies. After a brief description of the structure of these technologies? development under COMRO?s stewardship, the paper turns to an overview of the structure of innovation within which these hydraulic technologies were developed. A central focus of this paper is systematic review on whether similar technologies are likely to emerge in the present system of innovation and the role played by innovation policy.

Jan 1, 2006