Search Documents

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By Michael W. Oakland

Deer Island is the site of the Massachusetts Water Resources Authority (MWRA) wastewater treatment plant which, when completed in 1999, will serve 43 cities and towns in central eastern Massachusetts. Deer Island is located in the Boston Harbor, as shown on Figure 1. The existing wastewater treatment plant on Deer Island is being upgraded to include secondary treatment to comply with Federal require­ments. The new treatment facilities will process an average of 455 million gallons of sewage per day; total capacity will be about one billion gallons per day. The new treatment facilities will cover virtually the entire island. [ ]

Jan 1, 1994

By Jacques Deraisme

El método de minado es un componente importante de la estimaciòn de reservas, y el beneficio del proyecto está condicionado a la habilidad de minar selectivamente. En ese sentido, los métodos de lixiviación fallan en proveer estimaciones imparciales de mineral recuperable y exponen el proyecto a un riesgo indebido. Por ello, se preveó otro método alternativo como el Condicionamiento Uniforme y las Variables de Servicio donde las estimaciones puedan ser deducidas de un conjunto de simulaciones condicionales, que requieren menos hipòtesis pero consumen más tiempo. Por ello, el presente trabajo señala la variación de las reservas recuperables de acuerdo a la selección de método de estimación. La aplicación de tres métodos de estimación no linear- en un depósito de cobre se comparan con asunciones teòricas y las caracterìsticas geológicas del depósito. La performance relativa de cada método es evaluada por comparaciòn de las curvas de tonelaje-ley y contenido metàlico sobre un cut-off lìmite.

Aug 25, 2002

La prevención de accidentes es una de las obligaciones principales de la organización industrial, dado que la producción de estos, origina pérdidas económicas y humanitarias que detienen la producción y desarrollo de la compañía minera. En este contexto,el objetivo del presente texto es describir algunos aspectos preventivos sobre la política de accidentes en la mina como el formulario de informes empleado en la Cerro de Pasco Corporation. Los principios de la prevención de accidentes son: la creación y desarrollo del interés en la seguridad del empleado, análisis de hechos, y la aplicación de la acción correctiva adecuada. Una vez desarrollada las políticas del programa de seguridad, es necesario conocer las causas y circunstancias que derivaron al accidente, a través de un sistema de estadísticas que permita analizar los hechos de forma completa. Finalmente, se aplicará el procedimiento de informes sobre accidentes de trabajo, donde se indique las pautas consideradas a las autoridades pertinentes, se asegure la atención al accidentado y se reevalúe las condiciones que produjeron dicho accidente, evitando futuros infortunios y demoras de tipo burocráticas en la recopilación de datos.

Jul 20, 1957

This paper reports on recent field observations on the performance of support systems under different corrosion environments in Canadian underground mines. Phenomenological data are used to gain a better understanding of the main causes of corrosion in underground metal mines. Preliminary field data collected from five metal mines have been complemented by atmospheric and water sample analysis as well as fractography and metallographic studies. This has identified dominant factors that control the corrosion of support systems. The data are analysed in order to develop a support strategy for mines operating in corrosion environments.

Jan 1, 2008

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009

By E. Munnik

The Chambishi Metals Cobalt Plant in Zambia has recently installed a novel oxidation/precipitation pressure leach process as part of the COSAC (CObalt from Slag And Copper as by-product) Project. Aniron-cobalt-copper alloy, produced by the carbothermic reduction of slag, is atomized and pumped to the COSAC Leach Plant, where cobalt and copper are recovered as dissolved sulphate salts, andiron is rejected primarily as hematite. Cobalt and copper are subsequently recovered as cathode metal in the existing Chambish ioperation by conventional electrowinning. This paper examines the challenges faced during the design and subsequent successful commissioning of the COSAC Leach Plant. The challenges discussed include alloy handling, autoclave design, autoclave cooler design, residue liquor recovery and the water balance design. Keywords: Chambishi, Avmin, COSAC, Zambia, Copperbelt, cobalt, copper, alloy handling, pressure leach, autoclaves, cooling, filtration.

Jan 1, 2003

By Howard A. Perko, M. Mae Benvenga, Heather H. Trantham

Displacement of soil and groundwater during helical pile installation can produce excess pore water pressures (PWP) in fine-grained soils. Pore water pressure reduces effective stress in the soil immediately adjacent to the helical pile shaft and near the helical piles. Previous studies have shown generation of PWP may affect the capacity to torque ratios of the helical bearing elements. Large diameter helical piles that generate much of their torque and capacity from shaft adhesion are affected by PWP and therefore exhibit significant pile "freeze" after installation. Computer modeling is used herein to evaluate PWP immediately adjacent to helical pile shafts during installation in various soil types. The models show the degree and distance from the shaft that is influenced by PWP during installation and the amount of time required for the PWP to dissipate. Pile freeze has been measured on several project sites by re‐torque measurements. These re-torque data are compared with computer modeling and correlations between saturated hydraulic conductivity and dissipation time are presented and discussed. INTRODUCTION Helical piles are full-displacement piles, meaning installation does not produce drill spoil. Soil is displaced laterally as the pile progresses into the ground. This displacement of soil causes an increase in PWP, which reduces adhesion between the pile and the soil. For helical piles with small-diameter shafts, adhesion contributes little to the overall capacity and torque of the pile, so PWP changes are not typically considered in determining pile capacity. In modern construction, the use of larger diameter helical piles has become very common. For large-diameter helical piles, changes in PWP immediately adjacent the shaft can be quite large during installation. Increased pore water pressure and reduced adhesion can have a temporary effect on pile capacity and installation torque.

Jan 1, 2018

By Larry Schneider

Are you one of the thousands of hunters, fisherman, or hikers who purchased handheld GPS systems over the past several years and then been disappointed in their accuracy and performance. Or maybe you are one of the hundreds of blasters who have attempted to use GPS as a method for locating the exact position of their blast and measure distances from the blast to nearby structures. If so, you may have found that the accuracy of the handheld GPS systems left much to be desired. It may be time to get the units back out of storage and give them another try. As of midnight, May 1, 2000, the federal government has turned off the “error” built into the system known as “selective availability.” Here is a brief explanation of what that means in a question and answer format.

Jan 1, 2001

By Charles B. Carpenter

[The Bureau of Mines selected Anahuac for a petroleum-engineering study because it is one of the notable fields of the Gulf Coast region. It is outstanding because the producing for is very thick; every modern technique of drilling' and development has been applied; complete records of all operations,, including detailed subsurface information have been kept; the field has been developed systematically; and every effort has been made to utilize the reservoir energy efficiently Data and information pertaining to the development anal operation were collected, compiled, and studied by the writers as if the field were under single ownership. The chief aim-of the stud,, was to increase the accuracy of the existing methods of estimating reserves by applying all the data collected during the modern development of an oil-field, These scientific aids include coring; electric logging; micropaleontology determinations of porosity, permeability of oil-bearing sands, and their connate water content; subsurface sampling of the reservoir oil; and depth-pressure measurements. Because the reservoir structure in the Anahuac field is extremely complex, special attention was given to methods of calculating the reservoir volume.]

Jan 1, 1941

By D. K. Caddel

Several problems exist with the present design of coveralls used by miners in low coal (seam height 48 inches or less). The back portion of the coveralls often tears when roof bolts or rough areas in the roof are hit. Movement in the shoulder area is restricted. Female low coal miners find it difficult to purchase coveralls that fit properly, and must remove both their hard hat and safety belt in order to urinate and defecate. The objective of this research was to design coveralls which would alleviate these problems. The following features were incorporated into the coveralls; padding in the upper back area to avoid tearing, an action pleat in the shoulders to increase mobility, an inseam zipper to more easily allow miners to perform their bodily functions, and reflective tape to increase visibi¬lity of the miner. A heavyweight denim fabric was used to increase warmth and durability of the coveralls. The coveralls were assessed K long four parameters (comfort, safety, worker productivity, and fabric suitability) using both an in-field assessment by low coal miners and simulation studies. The experimental coveralls proved superior to conventional coveralls along all four parameters. Work clothing sizes for female miners were developed.

Jan 1, 1982

By Braden T. Lusk, Rex A. Meyr, Kyle A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by MSHA and required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. A polycarbonate safe haven wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed in both half-scale and small scales in the University of Kentucky Explosives Research Team’s (UKERT) explosives driven shock tube. The constructed polycarbonate walls were tested multiple times to determine the walls resistance to blast pressure. The results for each test were analyzed and averaged to create one pressure versus time waveform which was then imported into the finite element program and modeled to compare deflections of each part to that was measured during testing for model validation. This paper summarizes the results.

Jan 1, 2014

By S. K. R. Iyengar

This report presents the results of a study to develop optimal designs for light-weight mine roof supports for use in underground coal mines. A load capacity of 196 kN (22 tons) and a height adjustable between 1.829 m (72 inches) and 2.438 m (96 inches) were taken as the design parameters and the design goal was a unit weighing less than 22.3 kg (50 lbs). Three alternative design concepts were explored, viz. mechanical, hydraulic, and hydro-mechanical and a total of 13 designs analyzed in detail. Steel, aluminum alloy and composites were the main potential construction materials investigated for suitability from structural, life, and safety and other considerations. The designs considered most promising for development were: (i) the mechanical screw-pin type using telescopic tubes and a fine adjustment screw thread section (ii) the all-hydraulic type, of steel, aluminum alloy or aramid graphite construction (iii) the hydro-mechanical design using telescopic tubes and a short stroke hydraulic cylinder for fine adjustment It is shown that by using realistic mathematical models for stress and deflection calculations, it is possible to reduce prop weight to the design goal. The analysis presented for all-hydraulic props is applicable to hydraulic cylinders on all mining equipment and similar machinery. This report includes the computer program and user's guide for analyzing hydraulic cylinders as well as a cross-indexed bibliography on structural composites.

Jan 1, 1978

By Charles B. Carpenter

[The Bureau of Mines selected Anahuac for a petroleum-engineering study because it is one of the notable fields of the Gulf Coast region. It is outstanding because the producing formation is very thick; ever modern technique of drilling' and development has been applied; complete records of all operations,, including detailed subsurface information have been kept; the field has ,been developed systematically; and every effort has been made to utilize the reservoir energy efficiently. Data and information pertaining to the development anal operation were collected, compiled, and studied by the writers as if the field were under single ownership. The chief aim of the study was to increase the accuracy of the existing methods of estimating reserves by applying all the data collected during the modern development of an oil field, These scientific aids include coring; electric logging; micropaleontology determinations of porosity, permeability of oil-bearing sands, and their connate water content; subsurface sampling of the reservoir oil; and depth-pressure measurements. Because the reservoir structure in the Anahuac field is extremely complex, special attention was given to methods of calculating the reservoir volume.]

Jan 1, 1941

Background information, formulae and a systematic set of procedures for estimating capital and operating costs for open pit mining equipment are presented in this paper. Firstly, equipment capital costs are required. These can be obtained from either suppliers, contractors or from first principles. The equipment is then divided into cost elements. Typically these are fuel and power requirements, spare parts consumption, wear items such as tyres, teeth and drill bits and finally repair and operating labour requirements. By consideration of the cost and life of each element a base cost can be derived. The base cost is then adjusted to suit specific site conditions such as the proximity to spare parts suppliers, the duty or ground conditions and the management and operator skills specific to the site. Hence, the same item of equipment can be costed to reflect different operations. Included are tables and data for typical plant items. Several examples are also given to illustrate the methodology being presented. The intention is to provide a set of procedures to allow costs to be built up from base level in a systematic and repeatable way. Applications for these costs include feasibility studies, budgetting and data for economic analyses.

Jan 1, 1990

By M Pizey, M Kingsbury

Since 1950 Stockton Open Cast Mine has excavated over 60 million tonnes of Brunner Coal Measures overburden sandstones and mudstones. The current operator, Solid Energy New Zealand, recognises that acidic drainage from this overburden and from historic underground mines has led to depressed pH levels and elevated levels of metals in streams draining the Stockton Plateau. These streams report to the Ngakawau River. To quantify the effects of mine site acid drainage remediation/mitigation on the lower Ngakawau River water quality, a catchment hydrogeochemical model has been field calibrated and ecotoxicology tests have been undertaken. The hydrogeochemical model indicates that pre-mining and present pH values in the lower Ngakawau River are similar but present aluminium and iron concentrations are elevated. Ecotoxicology tests have semi-quantified the critical metal concentrations and interim water quality targets to achieve ecological recovery are presented. Analyses of long-term total suspended solids (TSS) and turbidity monitoring in the lower Ngakawau River and St Patrick's Stream indicate that TSS of 120 mg/L and turbidity of 20 NTU are exceeded for <20% per cent of the time. Hence, specific criteria to protect migratory native fish from turbid water are currently met in the Ngakawau River and St Patrick's Stream.

Jan 1, 2003

By Paul F. Gnirk, Ralph A. Wagner, Joe L. Ratigan

This thermomechanical analysis used the finite element method to investigate the behavior of crushed salt backfill in a waste disposal room situated in a salt dome repository. The first of two objectives was to determine the transient temperature rise and degree of thermomechanical consolidation that occur in the backfill as a function of drillhole depths. The second objective involved the evaluation of closure due to salt creep of unlined emplacement drillholes and the determination of pressure on steel sleeve liners in the drillholes should liners become necessary for canister retrieval. The retrievability period was considered to extend for 25 years after waste emplacement. The canisters were assumed to contain ten-year old high level waste with a thermal output of 4.3 kW at the time of emplacement.

Jan 1, 1981

This work presents: 1.) the results obtained from measurements of temperature profiles in pillars and at working faces of three coal mines located in Colorado and New Mexico, 2) a comparison of the experimental results with theoretical predictors based on linear heat flow models, and 3) temperature profile predictions based on a two dimensional coal mine model with an inclined crack located in the roof or wall of the opening. The thermal properties of the coal and shale samples taken from the mines were used as input data for the computer model. Good agreement was found between the measured profiles and the theoretical values obtained with the one dimensional model. The two dimensional model results show that a visible crack (0.01-0.07-ft thick) in a coal roof causes a surface temperature difference from 0.2 to 1°F at the edge of the crack for rock exposed to air from 1 hr to 288 hrs and with the air to rock temperature differences from 2°-6°F. A temperature difference of 0.3 °F was found between solid and broken rock in a shale roof with a 0.03-ft thick crack inclined 45° to the horizontal after a ventilating time of 48 hrs and the air to rock temperature difference of 2.1°F.

Jan 1, 1972

Geophysical anomalies result from the passage of hydrothermal fluids through rocks. Interpretation of these anomalies, when integrated with available geological and geochemical data, assists the construction of a conceptual model of the original hydrology of the system. The original extent of a geothermal system is often indicated by the distribution of low resistivity argillic clay alteration. Quartz-adularia vein deposits, silica sinters or stockwork (often mineralised) cause local increases in resistivity. Appropriately chosen electrical techniques can therefore be used to help target such structures. Airborne magnetic surveys have also proven useful in New Zealand epithermal exploration, because hydrothermal fluids destroy magnetite causing extensive demagnetisation anomalies. Ground magnetic surveys can sometimes be useful for geological interpretation on a local scale. Positive gravity anomalies may occur as a result of mineral precipitation (silica or calcite) in high porosity host rocks, while negative gravity anomalies can result from hydrothermal fracturing and leaching of relatively dense host rocks. The relative merits of these geophysical techniques as used in the exploration of epithermal mineral prospects are discussed, with particular reference to the Hauraki Goldfield. The preferred method for defining zones of quartz veining/silicification is vector or tensor gradient resistivity. Exploration strategies and technique refinements are suggested as a means of improving the resolution of potentially mineralised target structures, in a more efficient and cost effective manner.

Jan 1, 1993