Search Documents

By F. T. Cawood

One of the consequences of globalizing mine finance is a necessity to apply uniform accountancy and valuation standards that are clearly understood and consistently applied by the global investment community. However, each country has unique circumstances, which sometimes make it difficult to align domestic practice with international requirements. South Africa is no exception and issues such as its political history, a taxation regime enforcing different rules on different mineral producers and a unique mineral rights ownership distribution, are barriers to internationalization. The economy is in a transitional phase as a result of the many and diverse policy documents following the change in political dispensation in 1994. Many of these documents have recently been implemented through new legislation and, in the case of mining, negotiations are continuing in order to ensure an acceptable outcome. This paper discusses the challenges that the South African minerals industry faces in the field of mineral property valuation. It draws on international experience and includes a discussion on the unique considerations that the South African mineral property market must take into account in establishing a code for this purpose, as such a code could later be aligned with international practice.

Jan 1, 2004

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By Ralph Dawson

The following additions to SLP-4 “ALWAYS AND NEVERS” have been approved by the Board of Governors since the last printing 6/97 and will be included in the next printing soon. They are also included in the Second Printing of the 17th Edition of the ISEE Blasters Handbook. Review them and apply those which might be applicable into your blasting program now.

Jan 1, 2001

This Bureau of Mines report comprises tables listing the name, location, and other pertinent data concerning certain future fuel-related projects. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities; the report covers the 26 States east of the Mississippi River. Of the total 594 projects for which information is provided, 492 concern coal mines and electric generating plants.

Jan 1, 1976

By Mario Samamé Boggio

El presente texto describe la importancia de la minería como actividad económica peruana -en tanto esta contribuye con el 49% de las divisas indispensables para importar los alimentos que faltan y la maquinaria para nuestra industrialización. Asi también aporta a las necesidades fiscales con sustancial aporte, producto de los impuestos, gravámenes y arbitrios que paga la industria extractiva.

Sep 1, 1961

By Solange Tamara da Fonseca

Uma das maneiras de se reduzir os custos no transporte de cargas é aumentando a quantidade de carga transportada por vagão, isto eleva a tensão no eixo do vagão e, consequentemente, a roda deve possuir maior dureza sem perda da tenacidade para suportar o desgaste. Para atingir os níveis de dureza necessários estão sendo desenvolvidas rodas ferroviárias com aços microligados ao nióbio (Nb), vanádio (V), molibdênio (Mo) e titânio. A empresa MWL Brasil fabricante de rodas ferroviárias forjadas desenvolveu dois aços microligados: 1° contendo o elemento microligante vanádio (0,13 % em peso) e 2° contendo os microligantes nióbio+molibdênio (0,014 % + 0,12 %, respectivamente), ambos os aços com 0,7 % C. Estes aços foram analisados microestruturalmente e mecanicamente a partir da roda ferroviária pronta. A microestrutura destes aços é composta basicamente por ferrita-perlita. Nas propriedades mecânicas o aço ao V apresentou os melhores resultados em todos os ensaios (tração na temperatura ambiente e 540 ºC, energia absorvida no ensaio Charpy e KIC) quando comparado ao aço sem microligantes ou com a adição de Nb+Mo. O melhor desempenho do aço ao V foi atribuído ao seu menor tamanho de grão austenítico e espaçamento interlamelar da perlita mais refinado.

Aug 16, 2017

By Nathan T. Lowe

This report updates an accounting of mines and prospects in the Seafoam mining district, Custer County, Idaho, begun during mineral appraisal of the Idaho Primitive Area. Thirty-two mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of mineral appraisal of the River of No Return Wilderness; most previously known locations were field checked and the updated information added to the data base. The district's major deposits include polymetallic fissure veins of gold-silver-lead-zinc-copper hosted by granodiorite and quartz monzonite which have been intruded by dikes ranging in composition from rhyolite to dacite, and vein type replacements of silver-lead-zinc-copper hosted by calcareous xenoliths imbedded in major intrusives. These deposits may be related to the intrusion of the Rapid River pluton or the Casto pluton. The dominant northwest structural trend is parallel to an aeromagnetic high, a weak gravity salient, and the Blue Bunch Mountain dike swarm.

Jan 1, 1983

By Paul L. Russell

Interest in the western oil shales of the US began in about 1908, with the first retort in Colorado constructed in 1917. The most successful early developments were near Elko, NV, where the Catlin Shale Products Co. produced more than 1.9 dam3 (12 000 bbl) of shale oil during 1920-1924 and at Rulison, CO, where a US government operation produced about 570 in 3 (3 600 bbl) of shale oil during 1926-1929. Plentiful low-cost crude oil was developed about this time and shale oil was of little or no interest until after World War II. From 1944 to about 1972, several companies, and the US government, operated shale oil mines and recovery plants in Colorado. While technical successes were achieved and an estimated 40-56 clam' (250 000-350 000 bbl) of shale oil were produced, economics were not favorable and commercial production was not achieved. In recent years domestic production of crude oil supplies has not kept pace with US consumption. The growing shortfall has been met with imports. The cost of imported oil has continued to escalate and increased US dependence on petroleum imports are national concerns, because of the negative impact on US balance of payments and an increasing dependence on other nations for US energy needs. In 1978, petroleum imports equaled about 44% of demand, up from 23% in 1970, but down from 48% in 1977 because of availability of Alaskan North Slope crude oil. Reduced domestic consumption and other factors have reduced current imports to about 40-45% of de¬wand-but at ever increasing cost. The growing shortage of crude petroleum and its increasing cost have resulted in renewed worldwide interest in oil shales. In the past, the main obstacle to oil shale development (progress toward commercial production) has been economics-shale oil cost too much to develop and thus could not compete with conventional petroleum crudes. Even with today's inflated energy prices, some experts say the production of synthetic crude oil from oil shale is, at best, marginally economic. The 1973-74 Arab oil embargo and increased crude oil costs-along with the federal government's offer to lease oil shale lands-resulted in renewed

Jan 1, 1981

This paper describes the excavation of No. 1 Power Station Lift Shaft at the Kiewa Hydro-Electric Project. The advantages and limitations of the borehole method are outlined, and general principles of plant design are discussed.INTRODUCTIONFor many years, attempts have been made to reduce mine development costs by various methods. Some of the, techniques of tunnelling have been adopted in horizontal headings, and in main vertical shafts, mechanical plant has displaced hand labour with notable success. However, in the field of small rises and winzes, improvements have largely been effected by attention to details of procedure. The most promising avenues for' substantial reductions in cost relate to:(a) Long-hole drilling(b) The borehole method(c) Calyx drilling.Whilst each of these methods has its peculiar advantages, the borehole rising method is probably most useful, and capable of wide application.In brief, the borehole method of rising requires a, drill hole parallel to the axis of the rise. A hoisting rope is passed through the borehole, and is attached to a platform on which the rising crew are raised with their equipment to the drilling position in the rise.When properly planned, the method is particularly safe, and has generally received the approval of mine inspectors and safety authorities. Rising work is generally hazardous, even when special timbering methods are used. In...

Jan 1, 1959

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020

By Adauto Martins de Assis, Atan de Assunção Cardoso

Devido a sua alta demanda de produção e padrão de qualidade a indústria automotiva tem utilizado ao longo da história robôs nas mais diversas atividades como montagem, soldagem, pintura e inspeção. No intuito de levar esta realidade para a sala de aula de alunos de Engenharia Mecânica, foi desenvolvido um braço robótico didático, apresentando configuração semelhante à um modelo industrial, a ser utilizado como ferramenta de apoio ao ensino de robótica e outras disciplinas correlacionadas. Para isto, fez-se o uso associado da placa eletrônica Arduino e do software Matlab. Inicialmente foram obtidas as equações de cinemática direta e inversa. Os resultados mostraram que a posição teórica obtida apresentou um comportamento esperado conforme a metodologia adotada e o resultado experimental mostrou pequena variação de posição. Para a cinemática inversa, o tempo de resolução do conjunto de equações foi comparado à resolução do problema através de um método numérico. Com base nos resultados experimentais, foram feitas algumas sugestões de melhoria para o braço robótico didático e considerações relacionadas a acurácia de um robô industrial.

Oct 1, 2019

By Richard H. Spencer

The purpose of this program was threefold: (1) to identify the symptoms of poor or inadequate performance of trolley carrier phone systems; (2) to assess the root causes of performance difficulties and classify them on the basis of equipment, coupling, or transmission; (3) to propose, analyze, test, evaluate and verify means of overcoming performance difficulties. Based on interviews and discussions with knowledgeable persons, laboratory experiments, and in-mine measurements, it was determined that the major impediment to good carrier phone system performance is the extreme signal attenuation found on the trolley wire/rail largely due to the many bridging loads. Three means are identified to help overcome the performance difficulties: the low impedance trolley wire, a method of improving performance by capacitively loading the transmission line; the dedicated wire, a low-loss means of extending trolley signal coverage; the use of isolators to remove the offending bridging loads at the carrier frequency. Other subjects treated in the report are design reviews of hardware, guidelines for the use of information in the report, recommendations, and a description of a probe for measuring trolley wire current.

Jan 1, 1977

By R. A. Isberg

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75o coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 1, 1981

By R. Switalski, M. Schafer, R. Pintabona, M. Kritzer, B. Lukajic, S. Janosko

Methane gas caused an eight-month shutdown of mining operations at the Mill Creek, Phase 3, Tunnel. The gas-related shutdown occurred as the tunnel was advanced to an approximate distance of 2,700 feet, which constitutes approximately18% of the total tunnel length. The construction of an emergency ventilation shaft, a comprehensive program of de-gassing wells and an expanded gas monitoring system were used to mitigate the gas condition. When complete, this tunnel will be utilized to convey and store combined storm and sanitary sewage collected from a portion of Cleveland, Ohio and ten suburbs. This paper will provide an overview of gas related remedial measures and explain how these measures were integrated into the project to ensure safe tunneling conditions.

Jan 1, 2007

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By Bruno Leonardy Sousa Lopes

Este trabalho tem como objetivo mostrar a correlação entre as fases constituintes do aço superdúplex SAF 2507 na junta soldada por processo MIG-MAG, considerando os efeitos da energia de soldagem nas propriedades mecânicas e de corrosão. Os resultados mostraram que a energia de soldagem causou mudanças no balanço das fases a/?, na formação pontual da fase s nos contornos de grãos ferriticos e mudanças de microdureza e tenacidade nas regiões da zona fundida (ZF) e zona termicamente afetada (ZTA), além de promover o aumento da fase ? e do índice de resistência à corrosão por pite (PREN?), quanto maior energia de soldagem. Entretanto, a tenacidade na ZF diminuiu mesmo com maior formação da fase ?, coalescimento dos grãos ferriticos, elevando a microdureza na ZTA sob baixa energia de soldagem. Assim, espera-se que estes resultados permitam estabelecer diretrizes para procedimentos de reparo em aços superdúplex sob processo de soldagem

Aug 17, 2017

By Takashi Saito

Since early 1970?s skirt suction foundations (skirted foundation / bucket foundation) have been used as support for large fixed substructures or anchors for floating structures in offshore hydrocarbon development projects. In recent years skirt suction foundations are recognized as one of the solutions in foundations applicable to bridge substructures installed in waters, because skirt foundations have a wide variety of functions such as control of settlement during service life, less impact to environments during operation at installation site. This paper introduces general features of skirt suction foundations, and then discusses design practice of them for the application to bridge substructures, with reference to experiments in both laboratory and field.

Jan 1, 2013

By Heinrich Ries

I. INTRODUCTION. THE facts is presented in this paper, based chiefly on recon¬naissance made, during the summer of 1903, by myself and my assistant, Mr. R.. C. Brooks, cover practically all that portion of Texas lying east of the 99th meridian. The work was undertaken for the University of Texas Mineral Survey, and was to have been extended over the entire State, but the sudden termination of the survey prevented even the official publication of the results already obtained. Most of the mineral resources of Texas were fully treated by the First Geological Survey, but the clay-industry was tit that time little developed, so that only a few scattered notes concerning it are to be found in the Survey reports. The extensive exploitation of the clay-deposits, however, has emphasized their commercial importance, and has also made accessible many facts of exceptional interest concerning their geologic conditions. The erection of new plants for the utilization of clay-products is usually preceded by more or less prospecting, which, by reason of the scarcity of outcrops, and the geologic and topographic conditions of eastern and southeastern Texas, is often slow and difficult work. This is especially true in the Tertiary and Pleistocene areas, where the structural conditions much resemble those of the Atlantic coastal plain, the deposits being mostly lenticular in form, and surrounded by beds of sand. II. GENERAL GEOLOGY OF THE CLAY-DEPOSITS. The accompanying sketch-map, Fig. 1, shows the location of nearly all the deposits examined, their relation to the geology of the State, and the type of clay found in each. The geology is based on the published work of Hill, Cummins, Tail, Adams, Hayes and Kennedy, but the boundaries have unfortunately not been determined over the entire region covered by the map, and, in many areas, are only approximate. It will be seen that the clay-deposits range from Carboniferous to Pleistocene in age, the older deposits being found in the northwestern part of the area, while those of Cretaceous and Tertiary age lie to the east, southeast and south. The Pleistocene clays are found in part in a belt along the coast, and in part along many of the larger rivers, where they often underlie extensive terraces.

Sep 1, 1906

By R Harding, T Hunt

For the past 120 years, Portland cement manufacture has been undertaken on the shores of the Whangarei Harbour in northern New Zealand. Through a serendipitous conjunction of geo-chemistry, the argillaceous marl found on Limestone Island in the harbour and Tikorangi Hill provides a perfect mix of the various elements required for strong and durable cement. Golden Bay Cement, and its predecessors, have been the guardians and managers of the use of these minerals. As the demands of the concrete industry have increased, so have the needs of the manufacturing process. Careful mapping of the resource at both Portland and Wilsonville Quarries has been undertaken. This has allowed the Company to change the Quarry operation from a purely volume basis to one of selection and blending of constituent minerals. Within the manufacturing process, change has also been introduced. Analytical techniques, using x-ray fluorescence spectrometry, microscopy and the application of modem data collation, has allowed fine tuning of the process. The Company now produces an increasing diverse range of products for both the domestic New Zealand market and exports to various South Pacific countries. This paper discusses the processing of limestone and æcement rockÆ into cement clinker, an intermediate synthetic mineral ground into cement. It examines control and blending regimes, and some methods used in determining process efficiency. An important technique ærediscoveredÆ has been the application of microscopy to clinker.  Examination of the major silicate minerals enables interpretation of the kiln processing and feedback to process operators. It also enables a prediction of indicated performance when ground into cement. Examples this paper give an insight into the use of minerals from Northland in some of the more important construction projects in modem New Zealand.

Jan 1, 1999

By W E. Vance, B H. Ashton

The emission of seam gases into underground workings in coal mines is acknowledged as a major hazard, particularly methane due to its possible ignition. Acknowledge of seam gas parameters is important for the prediction of gas emission rates into the ventilating air current. They are also important as the basis for the evaluation of the likely contained gas as a possible energy source.   Gas content determinations for the Kupakupa seam have been made at the Huntly West Mine.  Applying the method of Creedy (1986) to face samples, gas contents of 1.80 and 1.66 have been determined. Using desorbed and residual gas content data a content of 1.92 m3/t has been derived. These are on an ash included basis. Calculations using the adsorption equation of Kim (1977) and coal quality have given a gas content of 2.19 m3 t. Long-hole exploration drilling at Huntly West Mine has provided information on gas pressure. A pressure rise test has given a reading of 500 kPa (absolute); this is low compared with the pressure given for the determined gas content from theoretical adsorption isotherms.

Jan 1, 1991