Search Documents

By M. Leroux, P. Lacombe, S. R. Rao, J. Y. Kim, J. A. Finch, G. Labonté, N. Macminn, M. Ounpuu

"Laboratory investigations on two complex ores, the A1 zone ore from Les Mines Selbaie and the Lyon Lake ore from Mattabi Mines Ltd. (Division of Noranda Minerals), have been carried out to determine some of the main variables in collectorless flotation. In particular, the effect of pulp potential (controlled by gas composition), conditioning time, pH and grinding media have been studied.Chalcopyrite showed the greatest response to collectorless flotation among the four major sulphide minerals present, followed by galena. Flotation of sphalerite was variable from minimal to important depending on the mineralogy and the pre-treatment performed. Appreciable silver recovery was achieved collectorlessly for the Lyon Lake ore while it could not be achieved for the A1 zone ore of Les Mines Selbaie. It appears that the difference between the two ores is related to silver's predominance as tetrahydrite in the Lyon Lake ore while it is as argentite and native silver in the A1 zone ore.The response of the ores to collectorless flotation is strongly dependent on the pulp potential, Ep, and pH. Using different gas compositions and different conditioning times it was found that collectorless flotation occurs when Ep is +195 to +295 mv (vs SHE). The actual on-set potential for collectorless flotation is dependent on the ore. A too high potential or prolonged oxidation leads to a decrease in selectivity. Some other factors were examined, notably the effect of pH and the type of grinding media on the selectivity achieved in the laboratory.Preliminary results from a plant trial at Mattabi Mines Ltd. confirmed that collectorless flotation occurs and that it is preferential for chalcopyrite and to a lesser extent galena. Collectorless flotation was not attempted at Les Mines Selbaie. However, examination of the distribution of collector between the different addition points in the copper circuit suggests that it may be present."

Jan 1, 1990

By Syd S. Peng, C. Y. Chen

Introduction The Surface Mining Control and Reclamation Act was passed in 1977 to put an end to the uneven environmental standards and enforcement established by various coal mining states in the US. One year after passage, the Secretary of Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for state regulatory programs under the Act and to allow states to assume primary regulatory responsibility. To implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules. But they must take into consideration the differences between surface and underground coal mining. The regulations developed by the Secretary in 1979, with respect to subsidence control, included: • a subsidence control plan as part of the permitting process; • substantive provisions establishing performance standards for subsidence control; and • provisions providing for the prohibition of mining under perennial streams, impoundments larger than 24.6 dam3 (20 acre ft), and certain public facilities and urban areas. Industry challenged the Secretary's regulations implementing the subsidence control provisions. The litigation was consolidated with all other challenges to the permanent program regulations. (Permanent Surface Mining Regulation Litigation, Civil Action No. 79-1144; D. D.C., May 16, 1980.) In two opinions dealing with the multitude of issues raised by both industry and environmental groups, the US District Court of the District of Columbia ruled against industry. It upheld the promulgated subsidence control provisions. The US Court of Appeals stayed the appeals pending the agency's review and revision of its regulations. The regulatory reform was conducted in accordance with the order from the Secretary of Interior and the President in 1981. As a result, the subsidence control regulation was revised, reproposed, and finalized in June 1983 (Federal Register). This regulation, along with others, was again challenged by environmental groups and industry. On Oct. 1, 1984, the court, after finding the Secretary's reading of the Act reasonable, upheld the 1983 subsidence regulation except for one section. On Feb. 21, 1985, in accordance with the court's ruling, the Office of Surface Mining (OSM) suspended a portion of 30 CFR 817.121 (c)(2) concerning the damage correction requirement for structures or facilities and reproposed it on July 8, 1985 (Federal Register). In conjunction with a request for public comments, OSM now also seeks comments on the omission from the 1983 rule of the requirement in the 1979 rule regarding a presubsidence survey and monitoring of damage to structures. Technical issues related to subsidence regulations The subsidence regulations of June 1, 1983, consist mainly of two parts: a subsidence control plan as part of the permitting process; and substantive provisions establishing performance standards. The latter also includes provisions for prohibiting mining under certain areas. Under subsidence control plan section 784.20, minimum require-

Jan 2, 1986

By Å. Kruukka, H. F. Broicher

The iron ores of the Kiruna mine in Sweden are of exceptional quality except for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998, LKAB has been testing prototypes of LIF (laser-induced fluorescence) analyzers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground, the mining engineer supports the efforts of the metallurgist in the processing plant.

Jan 1, 2002

By M. N. Barbier

Según la obra del Ministerio de Educación Nacional de Francia existen 112 escuelas de ingenieros que este año formarán total alrededor de 6.000 ingenieros. Sin embargo, surgen algunos problemas en la formación de esta profesión como: aquellos ligados al reclutamiento de los alumnos de las escuelas de ingenieros, para obtener el mayor número posible de alumnos jóvenes y bien preparados, y los relacionados a la actividad misma de las escuelas de ingenieros, tales como programas, métodos de enseñanza y relaciones con la industria. En ese sentido, el presente texto revisa dichos problemas y plantea soluciones respecto a ellos como: diversas mejoras en el régimen de los concursos de las grandes escuelas y duracíón de la preparación, así como una reducción del número de materias enseñadas y la adopción de métodos activos de la enseñanza en lugar de aquéllos que se limitaban a exigir la presencia física de los alumnos.

May 1, 1965

By Andrés Llatas

El presente trabajo describe el comportamiento anódico de los sulfuros de cobre en las soluciones de ácido sulfúrico y férrico a través de la técnica potenciostática. En este sentido, se realiza una interpretación de los fenómenos psíquicos y cinéticos de la disolución en los sulfuros de cobre, considerando su importancia económica y las características de materiales refractarios que poseen los procesos convencionales de lixiviación.

Aug 26, 1988

By Roger C. Malan

The Monument Valley and White Canyon districts are in northeastern Arizona and southeastern Utah. Exploration and mining for uranium has been conducted in these districts since the late 1940's. In July 1965, ore reserves plus ore production at 174 properties were approximately 3.3 million tons of ore containing about 19 million pounds U3O8, of which about 10 per cent remained in reserves. The two largest mines, Monument No. 2 and Happy Jack, together account for about 45 per cent of the sum of production and reserves. Approximately half the deposits in these districts contain less than 1000 tons of ore. Nearly 5000 feet of Permian, Triassic, and Jurassic sedimentary rocks, mainly continental in origin, are exposed in these districts. All the important uranium deposits are in the Shinarump, the basal member of the Chinle Formation of Triassic age. The Shinarump lies on a widespread unconformity. It is composed of fluvial sediments, generally less than 100 feet thick, that were deposited by streams flowing from a source to the south. Most of the deposits are in an arcuate belt, convex to the west. This belt, 3 to 12 miles wide, extends from Monument Valley northward nearly 130 miles. It is along the western flank of the ancient Monument Valley-Monticello upland, an area that was slightly uplifted at the beginning and again at the end of deposition of the Shinarump. Erosion and subsequent reworking of the Shinarump sediments in the vicinity of this upland are postulated to have made possible the transportation, in solution, of the uranium contained in these sediments. The soluble uranium probably was carried by migrating ground water into sites favorable for precipitation in Shinarump beds bordering the upland. Thus, the original very small amounts of dispersed uranium in the early Shinarump sediments were accreted in the favorable belt where the accumulations of carbonaceous plant remains and their decay products provided a persistent reducing environment.

Jan 1, 1968

The Awareness and Preparedness for Emergencies at the Local Level (APELL) program is a process that helps people prevent, prepare for and respond appropriately to accidents and emergencies. APELL was developed by the United Nations Environment Program, in cooperation with industry groups, governments and local communities. Since its beginnings in1988, the program has been implemented in more than30 countries. APELL is a tool for bringing people together to allow effective communication about risks and emergency response. The program provides a common-sense approach to accident prevention and response.

Jan 1, 2003

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By R. S. Dean

[In E;encralt the I~8:al:ul',~,C,-J. Div:'sion conducts in\'8stigations relat-ing to the treatment of OrGR o.nd L!\3tallurl..'"lcal prod tctR froJ] t~e condi tion in :hich they are Itinod to t!1e refi!l(,u r.etal, . ' th 'the ob,icct of conserving natmal' resources .e..nd 81:mir..3.tin~ wacte by furn.i:::hir..g :nforInf'_tiou on current methods of metal11:.rgical practice, Tfu'..:.kir..g fund T!l;ntal .;;.otudie'" of metal-lurgical processe~, and de~eloping ~e~ proc6sses O~Q lloys to the point of dewonctrati:r:g the:'..r practicab'lity or va.lue}

Jan 1, 1941

By C. Froger

Since its creation in 1950, the Centre d'Etudes et Recherches des Charbonnages de France at Verneuil-en-Halatte (Oise) has been conducting many investigations concerned with airborne dust measurements, particularly in underground mines. The work has resulted in the development, a few years ago, of a new process of dust sampling, whereby the airborne dust particles are collected by a rotary filter of polyurethane foam rotating at high speed within 8 housing.

Jan 1, 1973

By F. Keith Shelton

"INTRODUCTION Cobalt is an essential metal in the normal industrial ac¬tivity of the United States. Being an important constituent of high-speed steels and other cutting-tool materials, it becomes of critically essential importance during periods of national emergency. 3/ The Presidential order of December 20, 1940, included cobalt among other essential commodities that could be exported only under license. The Executive order 4/ listed cobalt metal, cobalt oxide, and alloys containing more than 5 per¬cent cobalt as being within the licensing requirements.There was no domestic marketed production of, cobalt products from 1931 until 1940 when the Pyrites Co. 5/ produced some cobalt oxide. The major portion of the domestic cobalt requirements has been obtained from Northern Rhodesia, the Belgian Congo, and French Morocco. 6/ The uncertainty of sea transportation from those sources of supply demanded that steps be taken to obtain from domestic raw materials an adequate supply of cobalt for use in the materials required for production of indispensable machined war metal products. In connection with the national policy for attaining self-sufficiency of strategic and critical materials, the Bureau of Mines, Boulder City, Nev., Experiment Station initiated studies to recover cobalt from the low-grade oxidized cobalt deposits in the Goodsprings district, Nevada. Hewett 7/ reported occurrence of cobalt specifically in the Blue Jay, Columbia, Copper Chief, and Highline mines and generally over a widespread area in the district."

Jan 1, 1946

By J. L. Viljoen

t has long been the drive of the industry and all operations to create an environment that is free of injury and illness. We have come a long way; the leaders, executives, managers, supervisors and workers are to be commended for relentlessly driving to create, what I call a ?White Flag Day Every Day?. Yet I am also aware of the huge shift we still need to create in the industry, on the operations and in the workplaces to have them free of injury and illness. Keywords People, values, care, trust, belief.

Jan 1, 2011

By R. A. Vik

The influence of thermal treatments on the grindability of low-grade hematitic iron ores from Michigan and Minnesota was examined in bench-scale tests. Treatment factors were roasting temperature, roasting atmosphere, and ore cooling conditions. Bond ball mill grindability and work indices were used as response indicators in evaluating the condition of the ore. Of the three treatment factors evaluated, roasting atmosphere, which brought about the con version of iron oxides to magnetite, had the most significant effect; roasting temperature had the next most important effect; and cooling condition had the least effect. Optimum grindability was obtained with reduced-quenched products of both ores at 650° C, near the alpha-beta phase transformation of quartz.

Jan 1, 1971

By J. D. Davis

THIS-report gives results of in investigation of the carbonizing properties of 18 coals, including 2 from Alaska, 12 from British Columbia, 3 from Washington, and 1 from Utah. Each coal was carbonized in the standard 13-inch Bureau of Mines-American Gas Association (BM-AGA) retort at 900° C. Plastic properties were determined by the Gieseler and Davis methods, and agglutinating and free-swelling properties were determined by standard methods. Expanding properties were measured in the Bureau of Mines sole-heated oven. From the results of the tests on these single coals, three coals from the Crowsnest area in British Columbia, representing Elk River Nos. 4, 9, and 10, were selected for blending with the Utah coal, which was from the Lower Sunnyside bed, Horse Canyon mine, Emery County. Lower Sunnyside also was blended with Wilkeson -Nos. 2 and 3 (Washington) coals, Pocahontas No. 3 from McDowell County, W. Va., and the Oklahoma low-volatile coal used in the blend carbonized at, the Provo, (Utah) coke plant at the time this investigation was started. Most of the blends contained 3 percent hard pitch, which is the proportion used at the Provo plant. The blends were also carbonized in 13-inch BM AGA retorts at 900° C. High-volatile B coal from the No. 3 bed, Evan-Jones mine, Lower Matanuska, Valley, Alaska, yielded poorly fused coke or char. M-bed coal from the Chickaloon mine, Upper Matanuska. Valley, Alaska, ranked as medium-volatile bituminous and coked strongly. It expanded 39.6 percent in the sole-heated oven at a. charge density of 55.5 pounds per cubic foot..

Jan 1, 1952

By C. E. Brechtel

A testing program was conducted to design a cemented backfill fur hydraulic placement in underhand cut and fill mining of a steeply dipping coal seam. The testing evaluated the use of three different backfill aggregates, locally available at the coal mine, with Portland cement and five different pozzolans, including a Class F fly ash, a Class C fly ash, a cement kiln dust and ground smelter slag. Both viscosity and uniaxial compressive strength of backfill mixtures with different pozzolan and Portland cement contents were used to evaluate their suitability. Based upon the results of preliminary testing, an optimum mixture of alluvial sand with six percent Portland cement and ten percent Class F pozzolan was chosen for further compression testing.

Jan 1, 1985

A new method, localized uniform conditioning (LUC), was proposed in 2006 for modelling grades of small blocks of ore when data spacing is too broad for their accurate modelling by the linear regression based techniques, such as kriging (Abzalov, 2006). It represents a modified uniform conditioning (UC) technique that calculates the grade distribution functions for the large panels. LUC uses partitioning of the panels onto the small blocks and then ranks them in increasing order of grade. Based on the block ranks, a single grade value can be deduced for each block from the UC model of the gradetonnage relationships of the corresponding panel. After being first presented in 2006, the LUC method has been implemented in ISATIS© (commercial software) and became one of the common approaches for grade estimation when data spacing is broad in comparison with the estimated block size. Several years of study on the LUC method and its application to different geological environments, have allowed identification of the strengths and weaknesses of the method, which are as follows: ? The method produces accurate grade-tonnage functions, which are in a good accordance with a volume-variance relationship principles ? An initial ranking of the selective mining unit (SMU) blocks can be made by direct kriging from the sparse data grid. Therefore, the LUC method can be particularly useful at the early stages of exploration and mining project evaluations when sparsely distributed data is often the only available information ? Accuracy of the local estimation depends on the SMU ranking techniques. When ranking performed by direct kriging of the SMU blocks their spatial distribution is approximate. When the variogram of the studied variable is characterized by a large nugget effect, the block ranks produced by kriging can significantly differ from their ?true? distribution ? Block ranking can be improved using auxiliary data, either geophysical or geochemical. This allows use of the LUC method for integrating different data sets. In particular, LUC can be used for grade control in open pits by integrating resource definition data (e.g. drill-hole assays) and blast-hole assays. The latter are used for the block ranking.

Jan 1, 2014

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By S. J. Schatzel, W. P. Diamond

High methane emissions originating from the active face areas and from the fractured formations overlying and underlying the mined coalbed can adversely affect both safety and productivity in underground coal mines. Since ventilation alone may not be sufficient to control the methane levels in the longwall mining environment, gob gas ventholes have become a standard supplementary methane control option in many mines. As mines progress into deeper and gassier coalbeds, or as longwall panel size increases, ventilation and gob gas ventholes together may not be sufficient to maintain methane levels within statutory limits. To decrease the risk associated with methane emissions under these circumstances, in-seam horizontal methane drainage is often used to reduce the gas content of the coalbed prior to mining. Horizontal methane drainage borehole completion designs, drilling strategies, and degasification lead times may need to be adjusted for site-specific conditions due to mine design, geology, and the gas content of the coalbed. This study investigates different horizontal methane drainage borehole patterns, borehole lengths, and degasification times prior to and during panel extraction to evaluate their effectiveness in reducing methane emissions using a "dynamic" 3D reservoir modeling of a 38 1-m wide longwall panel operating in the Pittsburgh coalbed. Results of this study showed that dual and tri-lateral boreholes are more effective in decreasing emissions and in shielding the entries compared to fewer shorter, cross-panel, horizontal boreholes parallel to the longwall face. Modeling results showed that after 12 months of pre-mining methane drainage, the average longwall face emission rates can be reduced by as much as 10.3 m3/min and 6.8 m3/min using tri- and dual-lateral boreholes, respectively. It was also shown that if pre-mining methane drainage time is short, it is important to continue methane drainage during the panel extraction to maximize reductions in longwall face emissions since additional face emission reductions achieved during this period can be comparable to pre-mining degasification.

By Marcelo Macedo Fialho

No processo produtivo de aço, as empresas buscam continuamente a redução do custo de produção. Isto pode ocorrer através de diversas formas, tendo como as principais, o ganho de rendimento, o aumento de produtividade, a redução do homem hora aplicado e a redução do custo de matéria prima. Objetivando reduzir o custo de produção integrado placa bobina, a ArcelorMittal Tubarão busca aumentar o percentual de placas enviadas diretamente do Lingotamento Contínuo de Placas para o Laminador de Tiras a Quente. Os ganhos se dão, em primeiro plano, através da redução da intervenção nas placas aumentando o rendimento de placa e exigindo menos mão de obra para o corte e escarfagem de placa e, em segundo plano, através do aumento da temperatura média de enfornamento, propiciando maior produtividade no laminador de tiras a quente e menor consumo de energia para realizar o pré-aquecimento da placa antes do processo de laminação. Somado a isto, a maior disponibilidade de placas no pátio do LTQ, aumenta a chance de laminação exigindo menos paradas do LTQ e aumentando a produção. Os ganhos estimados com o projeto, apenas no que diz respeito a redução de custo de condicionamento são de 6MUSD/ano.

Jul 30, 2018