Search Documents

By L. Li

The backfilling of underground stopes is a common practice throughout the mining industry. The stresses imposed by the backfill on the surrounding rock mass need to be assessed because of their influence on ground stability and on the hydro-geochemical response of the fill material. There is, however, a complex interaction between the relatively soft backfill and the much stiffer adjacent rock mass. In recent years, the authors have presented results from investigations conducted on stress distributions (obtained numerically and analytically) in and around backfilled stopes with (sub)vertical walls. In this paper, the influence of stope inclination and of backfill properties is evaluated. Results indicate that, in general, the vertical and horizontal stresses in inclined stopes are close to, but somewhat smaller than the stresses in vertical stopes. Nonetheless, significant differences can be observed in some cases, especially for the vertical stress along the inclined central line and along the hanging wall. It is further shown that neglecting deformability in limit equilibrium analyses is an acceptable assumption. However, Poisson?s ratio and the dilatancy angle, usually neglected in limit equilibrium analyses, may have significant effect on the stress distribution. Results also confirm that the backfill strength parameters (cohesion and friction angle) are critical factors required to properly evaluate the stress distribution, at least within a certain range of parameter values.

May 1, 2007

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007

By Sérgio Luis de Moura Paiva Júnior

A reciclagem de materiais provenientes de combustíveis fósseis é essencial para a redução do impacto desses materiais no meio ambiente. Utilizar materiais reciclados exige, não somente a reutilização direta do produto, mas a criação de processamento e técnica desses materiais no intuito de produzir materiais melhorados após o tempo de uso, justificando o desenvolvimento de tecnologias nesse âmbito. Esse trabalho de conclusão de curso foi executado no intuito de auxiliar nas técnicas utilizadas por uma empresa de reciclagem de polietileno para a produção de pellets reciclados. Foram avaliadas as propriedades mecânicas e espectroscópicas de cada uma das fases e os processos realizados para a produção do material final: uma blenda polimérica constituída de diferentes tipos de polietileno reciclado. As técnicas de caracterização utilizadas foram Ensaios de Tração para a avaliação da tensão máxima e módulo de elasticidade dos materiais, Microscopia Eletrônica de Varredura (MEV) para avaliar dimensionalmente a região de fratura dos polímeros, Infravermelho com Transformada de Fourier (FTIR) para identificar os grupos funcionais presentes nos polímeros analisados, TG/DTG para o estudo das propriedades térmicas das fases separadamente e da blenda e determinação do grau de cristalinidade por meio da densidade. Foi possível não só identificar as funções orgânicas do polietileno na técnica de espectroscopia de infravermelho, mas também analisar um pico desconhecido em um dos polietilenos envolvido na mistura da blenda, que pode se relacionar com o seu resultado obtido no ensaio de TG/DTG, o qual aponta uma maior porcentagem de resíduo após a degradação total da massa do mesmo.

Oct 30, 2017

By Guido Huarcaya

El control de costos es una actividad en la minería que se relaciona con la gestión de la empresa en diversos aspectos. En ese sentido, el presente texto plantea los modelos de control de costos empleados en dicha compañía durante el período 2004-2011, donde se reduce los diversos ratios de consumo, de forma que permanezca ubicada en el primer cuartil de las empresas mineras en costos unitarios de producción.

Sep 12, 2011

By J. S. Dunning

One Federal Bureau of Mines research goal, to minimize requirements for domestically scarce mineral commodities through conservation and substitution, can be accomplished by utilizing more abundant elements such as iron, molybdenum, and titanium. An example of this research is the study of precipitation-hardening, iron-base alloys containing molybdenum and titanium, as substitutes for the high-tonnage stainless steels that are high in imported nickel and chromium. The precipitation hardened iron-base alloys are strengthened by a dispersion of the ternary Laves phase, Fe2 (Mo, Ti). Aluminum and chromium additions changed the solid solubility limits of molybdenum and titanium in a-iron and affected the composition of precipitating phases. A baseline composition of Fe-7Mo-2Ti was selected to study the effects of aluminum and chromium additions on the precipitation-hardening mechanism and microstructure and was also used in studies of mechanical properties and oxidation resistance. The study yielded workable, precipitation-hardening alloys, with elevated temperature strengths equivalent to or superior to types 304 and 316 stainless steels. Chromium and aluminum additions in combination were more effective in providing oxidation resistance than either addition was alone.

Jan 1, 1980

By P. J. Bethell

Background Increasingly complex geological conditions, with the presence of high ash binders in the mining horizon were encountered at the A.C. I. Dugout Mine near Price, Utah. This led to the production of high ash coal from the Dugout Mine during 2003 and 2004. This material had poor marketability and posed operating issues for the utilities burning the coal. Ash levels increased from typical levels in the 9-12% range to between 15 and 25%. etween 15 and 25%. Reviews of the mine plan and expected geological conditions indicated that further periods of high ash production could be expected. Action Plan Detailed sampling of the mine high ash production was carried out. The majority of the coal from the Dugout Mine is trucked to the Savage Coal Terminal (SCT) at Wellington, Utah where it is stored in multiple piles by quality. Coal at the mine is segregated by a CoalScan 2600, on-line analyzer into high ash, low ash and rock chute (waste material). From these piles, the material is crushed prior to shipment to SCT. The samples obtained from the various high ash piles were subjected to detailed sizing and washability analysis. Once this information was obtained, alternative circuit configurations were evaluated to process this material into a salable product. Water supplies in the arid terrain where the plant is located are scarce. This factor played a part in the final circuit design.

Jan 1, 2008

By D. F. Machuca-Mory

A change of support model consists of a procedure to change a stationary histogram at a small data scale to represent a larger scale; typically a distribution of sample drill-hole data is changed to represent a chosen selective mining unit (SMU) scale. Most grade variables average arithmetically. Thus, the mean stays the same for different scales, and the variance changes according to well-established theory using average variogram values. The longstanding challenge has been to predict how the shape of the histogram changes. The discrete gaussian model is widely used because it appears reasonable and introduces few artifacts; there are no artificial minimum/maximum values and the target mean and variance are reproduced exactly. The resulting distribution shape, however, is strongly dependent on a multivariate gaussian distribution. The authors generalize the approach by taking advantage of a property of the isofactorial model, which allows one to specify where the random function falls on the spectrum between a low-entropy mosaic model and a maximum-entropy diffusion model. A measure of dissemination (MD) is computed using a ratio of the madogram and the variogram. The change of support algorithm is developed that uses a variable measure of dissemination (VMD) that is easily calculated and fit to data from the deposit. The resulting VMD change of support model is very flexible to represent different mineralization styles encountered in practice; global predictions of recoverable reserves are more accurate and decision-making is improved. A number of real examples are shown to demonstrate the approach.

Jan 1, 2008

By M. L. Bakker

Keywords: Pyrometallurgy, top submerged lance (TSL), nickel, PGM, calcium ferrite, lime ferrite The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 9 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, whereupon it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and Platinum Group Metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By David J. Mack

A survey and critical appraisal of published information about Young's modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on. mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young's modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young's modulus. CalculatioX oP YouNg's Modulus from Theoretical or Empirical CoNsidera-tions Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Souther-land (1891), but Fess'enden4',~ made extensive calculations a few years later and arrived at the relationship: £ = 78.TOw(i)* where V is the atomic volume. In 1923, Peczalski, working from the same standpoint but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: where B is a constant of value about 8 . 107, p is density and mis atomic weight; the atomic volume, of course, being ml p. Portevind4 immediately pointcd out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: F- KT" where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson. Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff.50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium, 18

Jan 1, 1946

By P. C. Fletcher, E. Kaya

The Bond grindability testing procedure has been standardized to measure the same grindability values, i.e. Bond work index (BWi), for the same ore when tests are performed in different laboratories or by different operators. This is accomplished by the standardization of mill dimensions, tumbling speed, grinding ball charge weight and distribution, sample ore charge weight in the mill and operating practice. The results of this investigation reveal that the Bond work index grindability values may differ substantially with different standard Bond ball mills. This paper will review the results.

Jan 1, 2002

Your Excellency, on behalf of the Council of the Australasian Institute of Mining and Metallurgy, and, indeed, on behalf of everyone present, I extend to you a welcome, and our thanks for your gracious acceptance of the invitation to be here to-day and, later on, to present Honorary Membership Certificates. I also welcome the several official representatives of our Allies, of Great Britain and our sister Dominions.To Messrs. E. C. Driffield and E. J. Rigby, two of the original Foundation Members, who are with us to-day, I extend greetings.The present occasion is opportune to express, on behalf of a representative body of professional men, deep appreciation of the sacrifice which His Majesty the King has made, and will continue to make, by appointing His Royal Highness the Duke of Gloucester as Governor General of Australia and, therefore, His Majesty's senior personal representative in this country.I suppose, that as the primary reason for our assembly to-day is to celebrate the Fiftieth Year of the Institute's existence, I should properly on this occasion, give an account of its history and development. However, as this subject was ably covered by Mr. L. V. Waterhouse, in his Presidential Address in 1938, I trust I may be excused for selecting some other subject. I shall, therefore, exercise my privilege as President and give you a short history of the Mining and Metallurgical Industry of this country with special reference to its effect on the development of the Commonwealth and on the national economy. I apologize in advance for any statistics which I inflict upon you; some of these will be three or four years out of date, because of censorship restrictions. I shall as far as possible refer firstly to the industry prior to and including 1893, the Institute's foundation year, and then to subsequent development.Australia, is pre-eminently a pastoral and agricultural country and it leads the world in the production of wool. Nevertheless, it has an international reputation as a producer of gold and various metals and of minetal products.The development of gold mining in the decade 1840-50 was an epoch-making event in Australia's history, because, to quote one writer's apt phrase, "it precipitated Australia into nationhood." It was certainly responsible for a rapid increase in population. Thus, during the period 1841-1861 the population of Australia increased fourfold, from 221,000 to 1,170,000.The effect of the discovery of gold in Western Australia was even more striking. In 1890 the population of that State was 49,000 and in 1900 it was 180,000.Statistics in respect of gold are reasonably complete, even for the years prior to Federation, and it is interesting to note that the gold declared as...

Jan 1, 1944

By Sparrow G. J

The effect of polyelectrolyte flocculants on the de-watering of a tailing suspension of very fine clay was investigated.Sedimentation and filtration experiments were carried out in the labqratory to characterise the de-watering properties of the tailing. The results were used to calculate the effect of flocculant additions on the drainage and vaporation components of the de-watering of a clay suspension ponded on to a sand drainage bed.A flocculant increased the drainage rate, but decreased the volume of water that could be removed by drainage leaving more water to be lost by evaporation.The sorptivity values measured in the laboratory were used in the de-watering equation previously established for the tailing to estimate the effect of flocculant additions on the time required to de-water the suspension from 18.2 to 60 per cent solids w/w. The calculated de-watering times were found to increase or decrease depending on the volume of water removed by drainage and the prevailing evaporation rate.

Jan 1, 1980

By Peter W. Kauffman

This Bureau of Mines publication is designed primarily to provide mine engineers and production-level mine managers with the following: 1. Information to assist them in making the decision to retreat mine and in selecting the best retreat mining technique for specific mining conditions. 2. Information on mine planning that will enable them to design mine layouts for safe and efficient retreat mining. 3. Information that will enable them to develop a section foreman's handbook. The manual has been organized to gradually increase in level of detail as the reader progresses from beginning to end. Individuals interested in an overview of retreat mining can confine themselves to the first few chapters. Those interested in mine planning, should read the middle chapters as well. Those interested in the development of a foreman's handbook should read the entire manual.

Jan 1, 1981

An Integrated Solid Waste Management Method for Western Macedonia, Greece

Sep 13, 2010

By Daryl W. Wurster

The Liberty Bridge in Greenville, South Carolina is a curved, cable-stayed, pedestrian bridge with primary support provided by two towers. The bridge is part of the Falls Park redevelopment. The bridge was originally designed to be supported on drilled piers. Alternately, the bridge was supported on a combination of micropiles and anchor piles because of difficult access and subsurface conditions. The use of micropiles and anchor piles led to improved construction scheduling and reduced costs. Micropiles were used to resist compressive loads. Anchor piles were used to resist tensile forces and to eliminate excessive settlement of pile caps into underlying fill during pre-stressing. This paper describes the site history, bridge construction, site and subsurface conditions encountered, and the decisions that led to support of the bridge using micropiles and anchor piles and foundation construction.

Jan 1, 2006

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

By Charles B. Kenahan

A summary of Bureau of Mines research on utilization and disposal of solid wastes is presented, accompanied by an extensive bibliography of related publications. The Bureau's Solid Waste and Materials Recycling Program is directed toward four main areas of research, development, and demonstration: (1) extraction of mineral, metal, and energy values from urban refuse; (2) upgrading and recycling of automotive and related ferrous and nonferrous scrap; (3) utilization and stabilization of mine, mill, and smelter wastes; and (4) recovery and reuse of values from industrial waste products. A contract and grant program that supplements the in-house research and aids in the training of manpower in management of mineral-, metal-, and energy -based solid wastes is also discussed. This publication is an updating of Bureau of Mines Information Circular 8460 issued March 1970.

Jan 1, 1971

By Fun-Den Wang

This report presents theoretical studies and experimental work dealing with the detection of dangerous roof and pillar conditions in underground mines through measure¬ment of temperature differences on the surface of the mine opening. The theoretical work is directed at modeling the circumstances where a loose slab of rock might be detected. The experimental work provides input data for the theoretical models. At the beginning of the project, little was known by the authors of the conditions that would permit detection of a loose slab of rock or coal by measuring the surface temperature differences. The U.S. Bureau of Mines had found that there were detectable surface temperature differences on the roofs and pillars of mines. The Bureau contracted with Colorado School of Mines to measure temperature profiles around mine openings in an effort to learn if the temperature differences they had detected were directly related to loose pieces of roof and pillar rock. The Bureau was principally interested in learning if loose rock could be found in coal mines by measurement of surface temperature differences with an infrared thermometer.

Jan 1, 1972

The selective placement of coal strip mine overburden is examined. Physical end chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions of similar problems. Five mining methods already used in the industry, that are capable of selectively handling; waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons arc made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided.

Jan 1, 1981

By James L. Oleson, Hunter R. Propsom, Kevan J. R. Ford, Robert D. Henderson, Bob Musgrove

"Kinross’ Fort Knox Gold mine, near Fairbanks, Alaska has successfully implemented two major metallurgical continuous improvement projects resulting in growth of gold production and an extension of mine life. In 2009, Fort Knox produced 263,153 oz of gold at a cash operating cost of $543/oz. In 2010, approximately 63% of the gold will be produced from the CIP circuit, 15% of the gold from the gravity circuit and 22% of the gold from the heap leach.In 2009, a 44,000 ton per day run-of-mine valley fill heap leach facility was constructed and commissioned as a cost effective treatment option for low grade ores to supplement the higher grade mill. The heap leach facility will produce approximately 100,000 ounces of gold per year under severe winter conditions. Heap leach gold recovery, based on test work shows 30% after a 55-day leach cycle, with long term ultimate gold recovery targeted at 65%. The paper presents the heap leach design concepts and production data.Additionally in 2009, installation of a Knelson gravity concentrator unit (XD70) was completed. This together with an Acacia intense leach reactor (AILR) has increased overall mill gold recovery from 79.3% to 80.7%. A manual shaking table gold recovery operation has been replaced by batch intensive cyanidation of the high grade Knelson concentrates. Increased removal of coarse gold and difficult-to-leach gold species from the grinding circuit, via the gravity circuit, has improved gold leach recovery in the conventional whole-ore tank leach CIP circuit. The paper presents plant operating data, showing the improvements over the old flowsheet.Focus on the metallurgical properties of the high grade and low grade end components of the Fort Knox ore has resulted in significant improvement to gold recovery."

Jan 1, 2011