Search Documents

By E. A. Holbrook

The data in this bulletin were obtained during an investigation of screening practice by the University of Illinois engineering experiment station and the United States Bureau of Mines under a cooperative agreement between them and the State of Illinois Geological Survey Division. Earlier work on this subject includes a study of the general practice of coal preparation in Illinois, made in 1914 and published in 1916,1 and an investigation of Illinois coal-washing methods, results of which were published in 1912 in a bulletin 2 that contained complete information on the methods then in use for sizing washed coal. OBJECTS OF THE INVESTIGATION The present investigation was limited to a study of screening as applied in preparing mineral products with the expectation of obtaining more comprehensive information on screening machinery.

Jan 1, 1925

By James D. Noll, Eileen Birch

In a previous study, the e?cacy of commercial and prototype impactors for sampling diesel particulate matter (DPM) in coal mines was investigated. Laboratory and ?eld samples were collected on quartz-?ber ?lters and analyzed for organic and elemental carbon. Coal dust contributed a minimal amount of elemental carbon when commercial cascade impactors and prototype impactors, designed by the University of Minnesota (UMN) and the US Bureau of Mines (BOM), were used to collect submicrometer dust fractions. Other impactors were not as e?ective at excluding coal dust. The impactors evaluated in that study were either not commercially available or were multi-stage, expensive, and di?cult to use for personal measurements. A commercial version of the BOM impactor, called the DPM Cassette, was recently introduced by SKCs. Tests were conducted to evaluate the performance of the DPM Cassette for measuring diesel-source elemental carbon in the presence of coal dust. Bituminous coals from three mines in two di?erent coal provinces were examined. The dust particle diameters were small and the coal dust contained a high percentage of carbon, there by giving a worst-case condition for non-anthracite coal mines. Results for the DPM Cassette were essentially identical to those obtained by the BOM impactors in a previous study. At a respirable coal dust concentration of 5.46mg m3, which is 3.8 times the regulatory limit, the DPM Cassette collected only 34µg m3 of coal-source elemental carbon.

By Thomas L. Ochs

The stripping of iron-laden solvent with hydrochloric acid in the iron-removal step of the clay-hydrochloric acid process for the extraction of alumina from calcined kaolinitic clay results in a loaded ferric chloride stripping liquor. Treatment of this stripping liquor at boiling with calcined kaolin to form insoluble Fe203(s) and a dilute A1C13 solution was undertaken by the Bureau of Mines to characterize process problems and to aid in sizing of solids-liquid separation equipment. Variables identified as important in the chemical reaction were calcined kaolin particle size, ratio of calcined kaolin to FeC13, and reaction time. These parameters were tested for significance and their interactions investigated. Fine calcined kaolin (-65 mesh) at a greater than 1:1 mole ratio of contained acid-soluble A1203 to Fe203 equivalent of the FeC13 in the stripping liquor required less reaction time than coarser (-16 mesh) material. Solids-liquid separation of the reacted slurries by both settling and filtration requires flocculation.

Jan 1, 2011

By Eldon Keith Stanek

This annual report deals with four distinct tasks related to research on the safety and reliability of mine electrical power systems. Task one is to develop tests and the associated instrumentation to detect incipient faults on a mine or any low-voltage power system. Task two is a dual effort related to the digital prediction of electrical transients on mine power systems and laboratory testing of transient suppression devices. Task three is also a dual effort. This task consists of both theoretical and laboratory work to assess both the reliability and the fail-safe characteristics of several items of protective equipment used in mine power systems. Task four consists of an effort to use programmable calculators and/or computer terminals to check overcurrent protective device coordination.

Jan 1, 1976

By Henry S. Washington

I. INTRODUCTION. DURING the last twenty years or so the chemical investigation of rocks has made great advances, and it is now generally recognized that a knowledge of the chemical composition is as essential as that of the texture or mineral composition-if not more so-for the proper classification of rocks and study of their origin and relationships. Rock-analyses have vastly increased in numbers and, what is of greater importance, in quality. New and improved methods permit of greater accuracy than was possible in the early days, and the list of chemical constituents frequently determined has risen from the seven or eight of the greater part of the nineteenth century to twenty or more. Indeed, rock-analyses with determinations of so many constituents are now commonly made by the chemists of the United States and Australia, while in Germany, Great Britain, France, and Italy the rarer constituents are determined more frequently than formerly. As a consequence of this modern, accurate work, it has been discovered that some elements which were formerly supposed to be rare are of wide-spread occurrence and are often present in considerable amount. The fact is further being developed that the elements tend to show certain relations of occurrence or abundance in connection with each other. This is a fact which is applicable to the rarer elements, and which also finds a broad geological and petrological expression in the recognition of petrographic provinces. We are beginning to obtain some definite, though as yet rudimentary, knowledge of the distribution of the elements among igneous rocks. Some of the results along these lines obtained by study of the vast accumulation of analytical data now available are well known to petrologists, while others do not seem to be so gener-

Sep 1, 1908

By F. A. Penning

This report describes the development of skip and guide desings for vertical shafts in deep vein mines. Skip and guide systems for bottom dump skips are identified as being used in current practice. Mine visits were made to obtain current information on the needs and problems of operating mines. Methods of structural and mechanical analysis of skip bodies and bails are outlined. A dynamic computer model was written to find the dynamic interaction between skips and guides for guides with geometric misalinements. A materials evaluation section identifies currentavailable and applicable materials that can be used effectively for new skip construction. Guide materials are also presented. Analysis includes the economies resulting from streamlined buntons and from low skip payload ratios. Selection of materials is based on strength, abra¬sion and corrosion resistance. Design requirements related to the shaft environment are presented. Consideration for the selection of guides and buntons is also given. Conceptual design includes the concept of cylindrical skips, center-seeking guide rollers, and asymmetric bail design to decrease dynamic interaction. An outline for field tests is presented. Future research areas are: testing, guide geometry measure¬ment, advanced suspension, dynamics, and structural configurations.

Jan 1, 1977

By Matthew Wallin

A part of the East Bay Municipal Utility District?s Folsom South Canal Connection Project, 430 feet of raw water pipe was installed using micro tunneling beneath the Mokelumne River. The access shafts for this crossing were constructed 50 and 35 feet deep through very dense sands and soft sandstone and siltstone. High groundwater and the immediate source of recharge from the river required watertight shaft construction methods. The shaft contractor, Drill Tech of Antioch, CA, used a brand new Bauer cutter-soil mixing (CSM) rig to construct the large shafts. The structural concept is similar to secant piles, but instead of creating cylinders of soilcrete, the CSM rig creates interlocking rectangular panels. This technology has been used previously in Europe, Asia, and Canada, but this was the first project to use CSM technology in the United States. Cutter-soil mixing technology has other applications beyond shaft construction, including retaining wall construction and levee reinforcement.

By C. M. Young

THE following paper has been prepared with the object of placing on record in the Transactions some facts concerning the present condition and future prospects of the coal industry of Illinois. In presenting it, the writer wishes to say that a considerable amount of the material contained is taken from the publications and records of the Illinois Coal Mining Investigations, the annual Coal Report of the State Mining Board, and the work of the State Geological Survey. Coal Beds and Mining Methods According to the latest maps of the State Geological Survey, there are only 19 of the 102 counties of the State some portion of whose territory is not within the borders of the coal measures. If outlying areas in Calhoun and Whiteside Counties are considered, the number is reduced to 17. This does not mean that all of the 85 counties that are partly or wholly underlain by coal measures will become producers, as there are some portions of the State in which the coal does not occur in beds of such thickness as to warrant the hope that it can be mined. The mining of coal is widespread, however, for in 1916 there was production from 51 of the 102 counties of the State. There seem to be no cases in which operations will be limited by depth, as none of the coal measures lie at depths much greater than those at which it has been proved that coal may be profitably mined in this field. In fact, the deepest shaft reaching a bed of bituminous coal in the United States is located in this State at Assumption, where coal only 3 ½ ft. (1.07 m.) thick is worked at a depth of 1004 ft.. (306 m.) The coal beds occur in the form of a basin which is deepest along a line extending through the central part of the State and bearing a, little west of north. The northern, western and southern borders of this basin lie within the boundaries of the State, but on the eastern side the Illinois field is continuous with the Indiana field. The glacial drift covers all except the extreme southern end of the State and the visible outcropping

Jan 9, 1917

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopic techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relating their inherent properties to properties such as volatile-matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used commercially.

Jan 1, 1970

In 1967 the United States consumed 58.8 quadrillion Btu of energy. Both the Atomic Energy Commission and the Resources for the Future, Inc., a private economic forecasting group, predict that the United States energy requirements will reach 135 quadrillion Btu by the year 2000. In 1967 bituminous coal produced 21.4 percent of the energy used in the United States and anthracite coal another 0. 5 percent. Coal Reserves Coal reserves make up about four-fifths of the United States storehouse of fuel in proven reserves. Seventy-five percent of all fuel, likely to be found and recovered is coal. Electric utilities consume more than half of the bituminous coal mined in the United States in generating 53 percent of the nation's electricity. Atomic Energy Commission analysts have proposed the development of a vast "national energy system" based upon long-distance electrical transmission from abundant untapped coal reserves in the western United States. The study predicts that even if uranium supplies are available and economic breeder reactors developed, coal requirements for electricity generation will more than double by 1980 and increase another 50 percent before the year 2000.

Jan 1, 1970

By Kermit G. Davis, Sean Gallagher, William S. Marras, Kimberly Kovacs

This study evaluated spinal loads associated with lifting and hanging heavy mining cable in a variety of postures. This electrical cable can weigh up to 10 kg per metre and is often lifted in restricted spaces in underground coal mines. Seven male subjects performed eight cable lifting and hanging tasks, while trunk kinematic data and trunk muscle electromyograms (EMGs) were obtained. The eight tasks were combinations of four postures (standing, stooping kneeling on one knee, or kneeling on both knees) and two levels of cable load (0 N or 100 N load added to the existing cable weight). An EMG-assisted model was used to calculate forces and moments acting on the lumbar spine. A two-way split-plot ANOVA showed that increased load (p<0.05) and changes in lifting posture (p<0.05) independently affected trunk muscle recruitment and spinal loading. The increase in cable load resulted in higher EMG activity of all trunk muscles and increased axial and lateral bending moments on the spine (p < 0.05). Changes in posture caused more selective adjustments in muscle recruitment and affected the sagittal plane moment (p < 0.05). Despite the more selective nature of trunk EMG changes due to posture, the magnitude of changes in spinal loading was often quite dramatic. However, average compression values exceeded 3400 N for all cable lifting tasks.

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

By S. E. Phillipson

The Mine Safety and Health Administration?s (MSHA) Roof Control Division (RCD) collects a variety of geological and engineering information pertaining to mining conditions in surface and underground mines throughout the United States. Recently, lineament analyses, trends of geologic structures, and inferred stress directions based on mapping at mines with problematic ground conditions, have been integrated into a GIS. The incorporation of different kinds of information into the same geographic coordinates and map projection, placed on digital geologic maps, allows site specific data to be evaluated in a regional geospatial context, identifying trends in the orientation of horizontal stress or patterns of structural geologic features. As more information is collected, the GIS will evolve as a tool for district- and basin-wide evaluations of controls on ground instability, and may evolve into a predictive tool for some kinds of geologic hazards. In addition to the geologic and geotechnical evaluations, the GIS also serves as a searchable database of previous mine investigations. The database can be searched for a variety of criteria, and the results displayed in real geographic coordinates to find the locations of previously visited mines or to evaluate mine fatality and injury data. This not only allows old reports to be found, but also places the information in a geospatial context with respect to neighboring mines or geographic areas. The GIS also has the capability to serve as a digital mine map repository, where maps can be stored in digital, georeferenced format for display in relation to each other and various themes of interest. This allows evaluation of multiple seam mining interactions and proximity to other mines, and on a national level could serve as an abandoned mine map database.

Jan 1, 2008

By B. P. Watson

Several large falls of ground occur annually in the narrow, tabular stopes mined in the Bushveld Complex. These falls comprise safety risks and cause substantial production losses and compromise efforts to increase productivity. Underground observations in conjunction with instrumentation sites were used to establish the strategic parameters required to describe the rock mass behaviour of shallow-dipping stopes on the Bushveld platinum mines. Existing rock mass rating systems were evaluated using the observations and instrumentation results. None of the current systems adequately described all the relevant geotechnical conditions. Thus a hybrid of several current systems was developed, and the proposed system is discussed in the paper. The new rock mass rating system is termed the ?New Modified Stability Graph? system and follows the method originally described by Mathews et al.1and revised by Hutchinson and Diederichs2.Changes have been made to some of the tables provided by Barton3and to the stress analysis suggested by Hutchinson and Diederichs2. In addition, the logistical regression analysis has been applied to databases, formed using the suggested analyses, for three support resistances and risk levels established.

Jan 1, 2004

The excavation of ramps and tunnels often requires high-speed development with (or without) the use of high-energy mining equipment such as loaders, dump trucks, TBMs and roadheaders. This high-speed development creates a challenge in terms of providing a safe and productive working environment. For example, heat from continuously exposed surrounding rock, heat from broken rock, heat generated by mining equipment, potential in flows of hot ground water, pollution from associated diesel equipment and the distance of the advancing face from fresh through-ventilation all have to be taken into account when designing ventilation systems for high-speed ramp and tunnel developments. This paper discusses methods of achieving acceptable environments at the face and along the length of the tunnel. The methodology has been successfully implemented in the development of long (up to 20 km) TBM drives in the Lesotho Highlands Project and in mining projects in hot rock using drill and blast methods as well as mechanized methods using continuous miners and roadheaders. The determination of heat loads includes calculation of the heat flow within the surrounding rock, evaluation of the operating cycle of the equipment and the contribution to the overall heat load of the broken rock as it travels out of the tunnel. The determination of heat loads from surrounding rock in new tunnels required a modification of the algorithms generally used for established excavations. The paper also examines the use of, for example, mobile duct and fan systems to ensure that fresh air is delivered to the specific areas where workers are located.

Jan 1, 2000

By Daniel Hauer

In considering the cost of rock excavation, but little attention has been given to the economical handling and breaking up of boulders. Very few records seem to have been kept as to the cost of such work, and although it is difficult for this reason, to set a fair price for breaking up and handling boulders of various sizes, yet the cost of this detail work enters very materially into the cost of solid rock excavation. The subject is worthy of close and prolonged study.

Jan 1, 2006

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user&apos;s manual, including a program listing, is included in the appendices.

Jan 1, 1974

By M I. Pownceby, N A. S Webster, R Pattel, N Ware

The decrease in quality of Australian iron ore, coupled with the demand for more efficient energy use, necessitates closer monitoring and optimisation of process conditions for iron ore sinter production. Sinter properties are correlated with the mineralogical content and traditionally, quality control has relied on methods such as Fe2+ determination, point counting via optical microscopy and automated electron beam techniques such as QEMSCAN; these can have a typical turnaround time of several days between sampling and reporting of results. As well, there is additional uncertainty around quantifying some of the complex mineralogical phases in sinter such as silico-ferrite of calcium and aluminium (SFCA) and SFCA-I, which are key phases influencing sinter quality. There is a clear need for the implementation of alternative analytical methodologies that offer a turnaround in hours or even minutes to provide information to accurately maintain production conditions.X-ray diffraction (XRD) is a technique widely used for the quantitative mineralogical phase analysis (QPA) of ores and processed materials in the iron ore industry. Partial least squares regression (PLSR) analysis methods have recently been suggested as an indicator of sinter Fe2+ content from powder XRD data without the need for rigorous and often time-consuming mineralogical analysis by the operator. In this study we provide results from the implementation of PLSR to predict the strength of iron ore sinter. Results are sourced from a well-constrained data set comprising strength properties (as quantified by a tumble index (TI)) from a series of compact laboratory test samples. Using this data set it was determined that PLSR has potential to be used as a method for calculation of sinter TI from powder XRD data and, therefore, process control.CITATION:Webster, N A S, Pownceby, M I, Ware, N and Pattel, R, 2017. Predicting iron ore sinter strength through X-ray diffraction analysis, in Proceedings Iron Ore 2017, pp 331–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. F. Skala

Additional testing of two prototype instruments for the discrete detec­tion of submicrometer particles in metal and nonmetal underground mines is described. The detectors are designed to utilize properties of submicrometer particles to distinguish between those produced by fires from mine ambient particles primarily resulting from diesel engine exhaust. One instrument is based on the ability to pyrolyze fire produced parti­cles, but not diesel exhaust particles. An alarm is produced when the ratio of pyrolyzed to unpyrolyzed particles exceeds a preset value. The other detector utilizes a continuous flow ion chamber preceded by a denuder to remove charged particles. Discrimination against diesel produced submicrometer particles results because the diesel particles are naturally more highly charged than fire produced particles. In-mine testing was conducted over a period of several months. Both in­struments exhibited an ability to discriminate against diesel exhaust. However, problems with the recording equipment, and with the instruments themselves, due to large ambient dust particles, prevented enough data from being obtained to choose between the two methods. Recommendations to correct the problems are made.

Jan 1, 1982